| Age | Commit message (Collapse) | Author |
|---|
|
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tobias Waldekranz says:
====================
net: dsa: mv88e6xxx: Improve indirect addressing performance
The individual patches have all the details. This work was triggered
by recent work on a platform that took 16s (sic) to load the mv88e6xxx
module.
The first patch gets rid of most of that time by replacing a very long
delay with a tighter poll loop to wait for the busy bit to clear.
The second patch shaves off some more time by avoiding redundant
busy-bit-checks, saving 1 out of 4 MDIO operations for every register
read/write in the optimal case.
v1 -> v2:
- Make sure that we always poll the busy bit at least twice, in the
unlikely event that the first one is quick to query the hardware,
but is then scheduled out for a long time before the timeout is
checked.
v2 -> v3:
- Fallback to the longer sleeps after the initial two poll attempts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this change, both the read and write callback would start out
by asserting that the chip's busy flag was cleared. However, both
callbacks also made sure to wait for the clearing of the busy bit
before returning - making the initial check superfluous. The only
time that would ever have an effect was if the busy bit was initially
set for some reason.
With that in mind, make sure to perform an initial check of the busy
bit, after which both read and write can rely the previous operation
to have waited for the bit to clear.
This cuts the number of operations on the underlying MDIO bus by 25%
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid a long delay when a busy bit is still set and has to be polled
again.
Measurements on a system with 2 Opals (6097F) and one Agate (6352)
show that even with this much tighter loop, we have about a 50% chance
of the bit being cleared on the first poll, all other accesses see the
bit being cleared on the second poll.
On a standard MDIO bus running MDC at 2.5MHz, a single access with 32
bits of preamble plus 32 bits of data takes 64*(1/2.5MHz) = 25.6us.
This means that mv88e6xxx_smi_direct_wait took 26us + CPU overhead in
the fast scenario, but 26us + 1500us + 26us + CPU overhead in the slow
case - bringing the average close to 1ms.
With this change in place, the slow case is closer to 2*26us + CPU
overhead, with the average well below 100us - a 10x improvement.
This translates to real-world winnings. On a 3-chip 20-port system,
the modprobe time drops by 88%:
Before:
root@coronet:~# time modprobe mv88e6xxx
real 0m 15.99s
user 0m 0.00s
sys 0m 1.52s
After:
root@coronet:~# time modprobe mv88e6xxx
real 0m 2.21s
user 0m 0.00s
sys 0m 1.54s
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ipv6 neighbor solicitation and advertisement messages
isn't handled gracefully in bond6 driver, we can see packet
drop due to inconsistency between mac address in the option
message and source MAC .
Another examples is ipv6 neighbor solicitation and advertisement
messages from VM via tap attached to host bridge, the src mac
might be changed through balance-alb mode, but it is not synced
with Link-layer address in the option message.
The patch implements bond6's tx handle for ipv6 neighbor
solicitation and advertisement messages.
Suggested-by: Hu Yadi <huyd12@chinatelecom.cn>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Sun Shouxin <sunshouxin@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since v2.5.44 and addition of ip_options_fragment()
ip_options_build() does not render headers for fragments
directly. @is_frag is always 0.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Robert Hancock says:
====================
Cadence MACB/GEM support for ZynqMP SGMII
Changes to allow SGMII mode to work properly in the GEM driver on the
Xilinx ZynqMP platform.
Changes since v3:
-more code formatting and error handling fixes
Changes since v2:
-fixed missing includes in DT binding example
-fixed phy_init and phy_power_on error handling/cleanup, moved
phy_power_on to open rather than probe
Changes since v1:
-changed order of controller reset and PHY init as per suggestion
-switched device reset to be optional
-updated bindings doc patch for switch to YAML
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Cadence GEM/MACB driver now utilizes the platform-level reset on the
ZynqMP platform. Add reset definitions to the ZynqMP platform device
tree to allow this to be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GEM controllers on ZynqMP were missing some initialization steps which
are required in some cases when using SGMII mode, which uses the PS-GTR
transceivers managed by the phy-zynqmp driver.
The GEM core appears to need a hardware-level reset in order to work
properly in SGMII mode in cases where the GT reference clock was not
present at initial power-on. This can be done using a reset mapped to
the zynqmp-reset driver in the device tree.
Also, when in SGMII mode, the GEM driver needs to ensure the PHY is
initialized and powered on.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updated macb DT binding documentation to reflect the phy-names, phys,
resets, reset-names properties which are now used with ZynqMP GEM
devices, and added a ZynqMP-specific DT example.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
* tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (30 commits)
Bluetooth: Increment management interface revision
Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set
Bluetooth: hci_h5: Add power reset via gpio in h5_btrtl_open
Bluetooth: btrtl: Add support for RTL8822C hci_ver 0x08
Bluetooth: hci_event: Fix HCI_EV_VENDOR max_len
Bluetooth: hci_core: Rate limit the logging of invalid SCO handle
Bluetooth: hci_event: Ignore multiple conn complete events
Bluetooth: msft: fix null pointer deref on msft_monitor_device_evt
Bluetooth: btmtksdio: mask out interrupt status
Bluetooth: btmtksdio: run sleep mode by default
Bluetooth: btmtksdio: lower log level in btmtksdio_runtime_[resume|suspend]()
Bluetooth: mt7921s: fix btmtksdio_[drv|fw]_pmctrl()
Bluetooth: mt7921s: fix bus hang with wrong privilege
Bluetooth: btmtksdio: refactor btmtksdio_runtime_[suspend|resume]()
Bluetooth: mt7921s: fix firmware coredump retrieve
Bluetooth: hci_serdev: call init_rwsem() before p->open()
Bluetooth: Remove kernel-doc style comment block
Bluetooth: btusb: Whitespace fixes for btusb_setup_csr()
Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
...
====================
Link: https://lore.kernel.org/r/20220128205915.3995760-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the dwmac-sun8i's stmmaceth clk isn't disabled even if the
the device has been runtime suspended. The reason is the driver gets
the "stmmaceth" clk as tx_clk and enabling it during probe. But
there's no other usage of tx_clk except preparing and enabling, so
we can remove tx_clk and its usage then rely on the common routine
stmmac_probe_config_dt() to prepare and enable the stmmaceth clk
during driver initialization, and benefit from the runtime pm feature
after probed.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Luiz Angelo Daros de Luca says:
====================
net: dsa: realtek: MDIO interface and RTL8367S,RTL8367RB-VB
The old realtek-smi driver was linking subdrivers into a single
realtek-smi.ko After this series, each subdriver will be an independent
module required by either realtek-smi (platform driver) or the new
realtek-mdio (mdio driver). Both interface drivers (SMI or MDIO) are
independent, and they might even work side-by-side, although it will be
difficult to find such device. The subdriver can be individually
selected but only at buildtime, saving some storage space for custom
embedded systems.
Existing realtek-smi devices continue to work untouched during the
tests. The realtek-smi was moved into a realtek subdirectory, but it
normally does not break things.
I couldn't identify a fixed relation between port numbers (0..9) and
external interfaces (0..2), and I'm not sure if it is fixed for each
chip version or a device configuration. Until there is more info about
it, there is a new port property "realtek,ext-int" that can inform the
external interface.
The rtl8365mb might now handle multiple CPU ports and extint ports not
used as CPU ports. RTL8367S has an SGMII external interface, but my test
device (TP-Link Archer C5v4) uses only the second RGMII interface. We
need a test device with more external ports to test these features.
The driver still cannot handle SGMII ports.
RTL8367RB-VB support was added using information from Frank Wunderlich
<frank-w@public-files.de> but I didn't test it myself.
The rtl8365mb was tested with a MDIO-connected RTL8367S (TP-Link Acher
C5v4) and a SMI-connected RTL8365MB-VC switch (Asus RT-AC88U)
The rtl8366rb subdriver was not tested with this patch series, but it
was only slightly touched. It would be nice to test it, especially in an
MDIO-connected switch.
Best,
Luiz
Changelog:
v1-v2)
- formatting fixes
- dropped the rtl8365mb->rtl8367c rename
- other suggestions
v2-v3)
* realtek-mdio.c:
- cleanup realtek-mdio.c (BUG_ON, comments and includes)
- check devm_regmap_init return code
- removed realtek,rtl8366s string from realtek-mdio
* realtek-smi.c:
- removed void* type cast
* rtl8365mb.c:
- using macros to identify EXT interfaces
- rename some extra extport->extint cases
- allow extint as non cpu (not tested)
- allow multple cpu ports (not tested)
- dropped cpu info from struct rtl8365mb
* dropped dt-bindings changes (dealing outside this series)
* formatting issues fixed
v3-v4)
* fix cover message numbering 0/13 -> 0/11
* use static for realtek_mdio_read_reg
- Reported-by: kernel test robot <lkp@intel.com>
* use dsa_switch_for_each_cpu_port
* mention realtek_smi_{variant,ops} to realtek_{variant,ops}
in commit message
v5) sent again v4 branch. Sorry
v4-v6)
- added support for RTL8367RB-VB
- cleanup mdio_{read,write}, removing misterious START_OP, checking and
returning errors
- renamed priv->phy_id to priv->mdio_addr
- duplicated priv->ds_ops into ds_ops_{smi,mdio}. ds_ops_smi must not
set
phy_read or else both dsa and this driver might free slave_mii.
Dropped
401fd75c92f37
- Map port to extint using code instead of device-tree property. Added
comment
about port number, port description and external interfaces. Dropped
'realtek,ext-int' device-tree property
- Redacted the non-cpu ext port commit message, not highlighting the
possibility of using multiple CPU ports as it was just a byproduct.
- In a possible case of multiple cpu ports, use the first one as the
trap port.
Dropped 'realtek,trap-port' device-tree property
- Some formatting fixes
- BUG: rtl8365mb_phy_mode_supported was still checking for a cpu port
and not
an external interface
- BUG: fix trapdoor masking for port>7. Got a compiler error with a
bigger
constant value
- WARN: completed kdoc for rtl8366rb_drop_untagged()
- WARN: removed marks from incomplete kdoc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trap door number is a 4-bit number divided in two regions (3 and 1-bit).
Both values were not masked properly. This bug does not affect supported
devices as they use up to port 7 (ext2). It would only be a problem if
the driver becomes compatible with 10-port switches like RTL8370MB and
RTL8310SR.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
External interfaces can be configured, even if they are not CPU ports.
The first CPU port will also be the trap port (for receiving trapped
frames from the switch).
The CPU information was dropped from chip data as it was not used
outside setup. The only other place it was used is when it wrongly
checks for CPU port when it should check for extint.
The supported modes check now uses port type and not port usage.
As a byproduct, more than one CPU can be configured. although this
might not work well with DSA setups. Also, this driver is still only
blindly forwarding all traffic to CPU port(s).
This change was not tested in a device with multiple active external
interfaces ports.
realtek_priv->cpu_port is now only used by rtl8366rb.c
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8367RB-VB is a 5+2 port 10/100/1000M Ethernet switch.
It is similar to RTL8367S but in this version, both
external interfaces are RGMII.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek's RTL8367S, a 5+2 port 10/100/1000M Ethernet switch.
It shares the same driver family (RTL8367C) with other models
as the RTL8365MB-VC. Its compatible string is "realtek,rtl8367s".
It was tested only with MDIO interface (realtek-mdio), although it might
work out-of-the-box with SMI interface (using realtek-smi).
This patch was based on an unpublished patch from Alvin Šipraga
<alsi@bang-olufsen.dk>.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of a fixed CPU port, assume that DSA is correct.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"extport" 0, 1, 2 was used to reference external ports id (ext0, ext1,
ext2). Meanwhile, port 0..9 is used as switch ports, including external
ports. "extport" was renamed to extint to make it clear it does not mean
the port number but the external interface number id.
The macros that map extint numbers to registers addresses now use inline
ifs instead of binary arithmetic.
Realtek uses in docs and drivers EXT_PORT0 (GMAC1) and EXT_PORT1
(GMAC2), with EXT_PORT0 being converted to ext_id == 1 and so on. It
might introduce some confusing while reading datasheets but it will not
be exposed to users.
"extint" was hardcoded to 1. However, some chips have multiple external
interfaces. It's not right to assume the CPU port uses extint 1 nor that
all extint are CPU ports. Now it came from a map between port number and
external interface id number.
This patch still does not allow multiple CPU ports nor extint as a non
CPU port.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is a mdio_driver instead of a platform driver (like
realtek-smi).
ds_ops was duplicated for smi and mdio usage as mdio interfaces uses
phy_{read,write} in ds_ops and the presence of phy_read is incompatible
with external slave_mii_bus allocation.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preparing for multiple interfaces support, the drivers
must be independent of realtek-smi.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the only two direct calls from subdrivers to realtek-smi.
Now they are called from realtek_priv. Subdrivers can now be
linked independently from realtek-smi.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to adding other interfaces, the private data structure
was renamed to priv. Also, realtek_smi_variant and realtek_smi_ops
were renamed to realtek_variant and realtek_ops as those structs are
not SMI specific.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed kdoc mark for incomplete struct description.
Added a return description for rtl8366rb_drop_untagged.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool rx-buf-len is for setting receive buffer size,
support setting it via ethtool -G parameter and getting
it via ethtool -g parameter.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
SUNRPC: add some netns refcount trackers
Effort started in linux-5.17
Our goal is to replace get_net()/put_net() pairs with
get_net_track()/put_net_track() to get instant notifications
of imbalance bugs in the future.
Patches were split from a bigger series sent one month ago.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct svc_xprt holds a long lived reference to a netns,
it is worth tracking it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
ethtool: add header/data split indication
TCP ZC Rx requires data to be placed neatly into pages, separate
from the networking headers. This is not supported by most devices
so to make deployment easy this set adds a way for the driver to
report support for this feature thru ethtool.
The larger scope of configuring splitting headers and data, or DMA
scatter seems dauntingly broad, so this set focuses specifically
on the question "is this device usable with TCP ZC Rx?".
The aim is to avoid a litany of conditions on HW platforms, features,
and firmware versions in orchestration systems when the drivers can
easily tell their SG config.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aggregation rings imply header-data split.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Robert Hancock says:
====================
Allow disabling KSZ switch refclock
The reference clock output from the KSZ9477 and related Microchip
switch devices is not required on all board designs. Add a device
tree property to disable it for power and EMI reasons.
Changes since v3:
-rework some code for simplicity
Changes since v2:
-check for conflicting options in DT, added note in bindings doc
Changes since v1:
-added Acked-by on patch 1, rebase to net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new microchip,synclko-disable property which can be specified
to disable the reference clock output from the device if not required
by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document the new microchip,synclko-disable property which can be
specified to disable the reference clock output from the device if not
required by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir points out that since we removed mii_lpa_to_linkmode_lpa_sgmii(),
mii_lpa_mod_linkmode_lpa_sgmii() is also no longer called.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of unnecessary if check on tx_desc pointer in
mvneta_xdp_submit_frame routine since num_frames is always greater than
0 and tx_desc pointer is always initialized.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert sparx5 to use the mac_select_interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for
PCS and eventually remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pavel Begunkov says:
====================
udp/ipv6 optimisations
Shed some weight from udp/ipv6. Zerocopy benchmarks over dummy showed
~5% tx/s improvement, should be similar for small payload non-zc
cases.
The performance comes from killing 4 atomics and a couple of big struct
memcpy/memset. 1/10 removes a pair of atomics on dst refcounting for
cork->skb setup, 9/10 saves another pair on cork init. 5/10 and 8/10
kill extra 88B memset and memcpy respectively.
====================
Link: https://lore.kernel.org/r/cover.1643243772.git.asml.silence@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Inline a part of ipv6_fixup_options() to avoid extra overhead on
function call if opt is NULL.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
udpv6_sendmsg() doesn't need dst after calling ip6_make_skb(), so
instead of taking an additional reference inside ip6_setup_cork()
and releasing the initial one afterwards, we can hand over a reference
into ip6_make_skb() saving two atomics. The only other user of
ip6_setup_cork() is ip6_append_data() and it requires an extra
dst_hold().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
udpv6_sendmsg() first initialises an on-stack 88B struct flowi6 and then
copies it into cork, which is expensive. Avoid the copy in corkless case
by initialising on-stack cork->fl directly.
The main part is a couple of lines under !corkreq check. The rest
converts fl6 variable to be a pointer.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Another preparation patch. inet_cork_full already contains a field for
iflow, so we can avoid passing a separate struct iflow6 into
__ip6_append_data() and ip6_make_skb(), and use the flow stored in
inet_cork_full. Make sure callers set cork->fl, i.e. we init it in
ip6_append_data() and before calling ip6_make_skb().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert a struct inet_cork argument in __ip6_append_data() to struct
inet_cork_full. As one struct contains another inet_cork is still can
be accessed via ->base field. It's a preparation patch making further
changes a bit cleaner.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It doesn't appear there is any reason for ip6_cork_release() to zero
cork->fl, it'll be fully filled on next initialisation. This 88 bytes
memset accounts to 0.3-0.5% of total CPU cycles.
It's also needed in following patches and allows to remove an extar flow
copy in udp_v6_push_pending_frames().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clean up ip6_setup_cork() and ip6_cork_release() adding a local variable
for v6_cork->opt. It's a preparation patch for further changes.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ipv6_push_nfrag_opts() doesn't change passed daddr, and so
__ip6_make_skb() doesn't actually need to keep an on-stack copy of
fl6->daddr. Set initially final_dst to fl6->daddr,
ipv6_push_nfrag_opts() will override it if needed, and get rid of extra
copies.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
