| Age | Commit message (Collapse) | Author |
|---|
|
Remove the include of <mach/hardware.h>, as no definitions
from it are used by the OHCI driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Lots of users are getting confused about the cp2101 driver. It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.
Cc: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch lowers the logging priority of certain messages to prevent
users from flooding the log files.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205. An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1. A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use kzfree() instead of memset() + kfree().
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1223) removes a bunch of unnecessary "inline"
annotations from the usbfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
These devices are better controlled with the LGPL userspace library
found at:
http://www.phidgets.com/downloads.php?os_id=3
and full documentation at:
http://www.phidgets.com/documentation/web/cdoc/index.html
Cc: Chester Fitchett <fitchett@phidgets.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The code in uhci-q.c doesn't have to use pseudo-negative values. I did
it that way because it was easy and because it would give the expected
output during debugging. But it doesn't have to work that way. Here's
another approach.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch disables USB regulators VUSB1V5, VUSB1V8, and VUSB3V1
when the USB cable is unplugged to reduce power consumption.
Added a depencency from twl4030 usb driver to TWL_REGULATOR.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support. Missing:
(a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
when DAVINCI_N_GPIO increases;
(b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
driven according to the ID signal, if cpu_is_..._dm355()
The new PHY control bits are ignored on DM6446.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host. This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.
However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable. And the procfs entry which once
allowed a manual workaround for this is now gone.
This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.
[ dbrownell@users.sourceforge.net: tweak patch description ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled. (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Tested with PIO, Inventra DMA, CPPI DMA.
[ dbrownell@users.sourceforge.net: fold in start_urb() update;
clarify only for bulk RX; don't accidentally clear WZC bits ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Avoid the following INFO from lock debugging:
[ 369.126112] =================================
[ 369.132063] [ INFO: inconsistent lock state ]
[ 369.136457] 2.6.28-maemo1 #1
[ 369.139387] ---------------------------------
[ 369.143782] inconsistent {hardirq-on-W} -> {in-hardirq-W} usage.
[ 369.149855] swapper/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
[ 369.154890] (&cdev->lock){+-..}, at: [<bf1979f0>] composite_disconnect+0x1c/0]
[ 369.163404] {hardirq-on-W} state was registered at:
[ 369.168348] [<c00788a8>] __lock_acquire+0x5d0/0x7d8
[ 369.173506] [<c0078b14>] lock_acquire+0x64/0x78
[ 369.178266] [<c0263a34>] _spin_lock+0x4c/0x80
[ 369.182905] [<bf19597c>] usb_function_deactivate+0x20/0x70 [g_nokia]
[ 369.189527] [<bf1a0a88>] 0xbf1a0a88
[ 369.193281] [<bf19f450>] 0xbf19f450
[ 369.197004] [<bf19fa3c>] 0xbf19fa3c
[ 369.200758] [<bf1a03a0>] 0xbf1a03a0
[ 369.204481] [<bf19f254>] 0xbf19f254
[ 369.208204] [<bf1a0158>] 0xbf1a0158
[ 369.211927] [<bf1a130c>] 0xbf1a130c
[ 369.215650] [<c01c21f0>] usb_gadget_register_driver+0x12c/0x28c
[ 369.221846] [<bf1a06bc>] 0xbf1a06bc
[ 369.225569] [<bf1a06e8>] 0xbf1a06e8
[ 369.229322] [<c002c2dc>] __exception_text_end+0x64/0x19c
[ 369.234877] [<c0081628>] sys_init_module+0x9c/0x194
[ 369.240004] [<c002c8e0>] ret_fast_syscall+0x0/0x2c
[ 369.245039] [<ffffffff>] 0xffffffff
[ 369.248793] irq event stamp: 218356
[ 369.252302] hardirqs last enabled at (218355): [<c003a77c>] omap3_enter_idle+8
[ 369.260420] hardirqs last disabled at (218356): [<c0264774>] __irq_svc+0x34/0x0
[ 369.267927] softirqs last enabled at (218348): [<c00585a4>] __do_softirq+0x134
[ 369.275892] softirqs last disabled at (218335): [<c005899c>] irq_exit+0x60/0xb0
[ 369.283308]
[ 369.283308] other info that might help us debug this:
[ 369.289930] no locks held by swapper/0.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
modules
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1212) converts usb-storage's freecom subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1211) converts usb-storage's shuttle_usbat subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1210) converts usb-storage's cypress_atacb subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1209) converts usb-storage's sddr55 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1208) converts usb-storage's isd200 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1207) converts usb-storage's sddr09 subdriver into a
separate module.
An unexpected complication arises because of DPCM devices, in which
one LUN uses the sddr09 transport and one uses the standard CB
transport. Since these devices can be used even when
USB_STORAGE_SDDR09 isn't configured, their entries in unusual_devs.h
require special treatment. If SDDR09 isn't configured then the
entries remain in unusual_devs.h; if it is then the entries are
present in unusual_sddr09.h instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
With "nousb" cmdline booting, built-in serial drivers (ie. airecable)
will trigger kernel oops.
Indeed, if nousb, usb_serial_init will failed, and the usb serial bus type
will not be registerd, then usb_serial_register call driver_register
which try to register the driver to a not registered bus.
Here add usb_disabled() check in usb_serial_register to fix it.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix ehci printk formats:
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Driver originally written by Qualcomm, but rewritten by me due to the
totally different coding style. Cleaned up the probe logic to make a
bit more sense, this is one wierd device. They could have prevented all
of this by just writing sane firmware for the modem.
Cc: Tamm Liu <tamml@qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We need to figure out what userspace programs are expecting from this
driver, so log them so we can try to get it right.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is for the Symbol 6608 barcode scanner in a fake "HID" mode.
Thanks to Dalibor Grgec for working with me to get this to start to work
properly.
Cc: Dalibor Grgec <dalibor.grgec@zemris.fer.hr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The patch changes the prototype of the isp1760_register() function to use
predefined types like phys_addr_t and resource_size_t rather than u64
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1204) adds a software retry mechanism to ehci-hcd. It
gets invoked when the driver encounters transaction errors on an
asynchronous endpoint. On many systems, hardware deficiencies cause
such errors to occur if one device is unplugged while the host is
communicating with another device. With the patch, the failed
transactions are retried and generally succeed the second or third
time through.
This is based on code originally written by Koichiro Saito.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Koichiro Saito <Saito.Koichiro@adniss.jp>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 64a87b24: [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
changed the scsi_eh_prep_cmnd logic by making it clear
the ->cmnd buffer. But the sat to cypress atacb translation supposed
the ->cmnd buffer wasn't modified.
This patch makes it set the ->cmnd buffer after scsi_eh_prep_cmnd call.
The problem and a fix was reported by Matthieu CASTET <castet.matthieu@free.fr>
It also removes all the hackery fiddling of scsi_cmnd and scsi_eh_save by
requesting from scsi_eh_prep_cmnd to prepare a read into ->sense_buffer,
which is much more suitable a buffer for HW transfers, then after the command
execution the regs read is copied into regs buffer before actual preparation
of sense_buffer.
Also fix an alien comment character to my utf-8 editor.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: stable <stable@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line. Over the years it has grown too big to be inline
any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove old comments about USB_EHCI_HCD.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
A USB-serial converter device is plugged into a system, and a process
opens it's device node. If the device is physically removed whilst the
process still has its device node open, then other processes can
sucessfully open the now non-existent device's node. I would expect
that open() on a device that has been physically removed should return
ENODEV.
This is manifesting itself with getty on my system. I do the following:
1. set up inittab to spawn getty on ttyUSB0, eg:
T1:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100
2. Plug in USB-serial converter cable
3. Wait for a login prompt on a terminal program attached to the serial
cable
4. Login
5. Pull the USB-serial converter cable from the box
6. getty doesn't realise that ttyUSB0 no longer exists as /dev/ttyUSB0
can still be opened.
7. Re-insert the USB-serial converter cable
8. You should no longer get a login prompt over the serial cable, as
the the USB-serial cable now shows up as /dev/ttyUSB1, and getty is
trying to talk to /dev/ttyUSB0.
The attached patch will cause open("/dev/ttyUSB0", O_RDONLY) to return
ENODEV after the USB-serial converter has been pulled. The patch was
created against 2.6.28.1. I can supply it against something else if
needs be. It is fairly simple, so should be OK.
I am using a pl2303 device, although I don't think that makes any
difference.
From: James Woodcock <James.Woodcock@ACULAB.COM>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This removes the fallback to the generic method. It is cleaner to
explicitely request it. Introducing this was my mistake. This will
be solved by an explicit test and the driver being allowed to request
what it needs to be done upon resumption.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
338b67b0c1a97ca705023a8189cf41aa0828d294 removed the info macro and
replaced its uses with dev_info. This patch does so for
usb-skeleton.c, which was missed.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make lines about usb_storage depending on SCSI visible when configuring the
kernel in a 80x25 console
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
