| Age | Commit message (Collapse) | Author |
|---|
|
- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
in the message header and firmware modules use h/w queue ID from
message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
messages. Used to translate host tag to firmware tag. bfa_lpuid()
is changed to bfa_fn_lpu() that encodes both PCI function and port
ID in BFI message header.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- If flash controller is halted unconditionally, this results in
illegal write access to flash controller register domain. Since
flash controller registers are only accessible once s_clk is started
- added logic to check for WGN status and halt flash controller only
if it is already running.
- Added check to wait for flash controller halt to be completed before
proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
are complete.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add logic to handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Added logic to unlock hw semaphore if the previos FW boot was
from flash based and the current FW initialization attempt is from OS.
- Added fix to update hbfails and hb_count stats during hwerror event.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added ASIC block configuration APIs:
- to create/delete/update the physical functions
- to do adapter/port mode configuration
- to query the current ASIC block configuration.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Bumped version from 2.6.2.3 to 2.7.0.3
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The init routine will now examine the cnic->max_iscsi_conn variable
before registering to CNIC during ulp_init.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch breaks the SCSI cmd completion into two parts:
1. The bh will allocate and queued work to the cmd specific CPU IO
completion kthread. The CPU for the cmd is from the sc->request->cpu.
2. The CPU specific IO completion kthread will call the scsi_cmd_resp
routine to do the actual cmd completion.
In the normal case, these IO completion kthreads should complete before
the blk IO times out at 60s. However, in the case when these kthreads
are blocked for whatever reason and exceeded the timeout, the call
to conn_destroy will have to iterate and exhaust all related work in the
percpu work list for all online CPUs. This will guarantee the protection
of the work->session and conn pointers before they get freed.
Also modified the event coalescing formula to have at least the
event_coal_min outstanding cmds in the pipeline so the SCSI producer
would not get underrun.
Also changed the following SCSI parameters:
- can_queue from 1024 to 2048
- cmds_per_lun from 24 to 128
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Have libiscsi_tcp have upper layers allocate the LLD data
along with the iscsi_cls_conn struct, so it is refcounted.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
iscsi_sw_tcp_conn_restore_callbacks could have set
the sk_user_data field to NULL then iscsi_sw_tcp_data_ready
could read that and try to access the NULL pointer. This
adds some checks for NULL sk_user_data in the sk
callback functions and it uses the sk_callback_lock to
set/get that sk_user_data field.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
be2iscsi passes the boot functions its phba object which is
allocated in the shost, but iscsi_ibft passes in a object
allocated for each item to display. The problem is that
iscsi_boot_sysfs was managing the lifetime of the object
passed in and doing a kfree on release. This causes a double
free for be2iscsi which frees the shost in its pci_remove.
This patch fixes the problem by adding a release callback
which the drivers can call kfree or a put() type of function
(needed for be2iscsi which will do a get/put on the shost).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This moves the check for NULL boot_sets to the iscsi_boot_sysfs
module instead of having the drivers do it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixed missing programming of the pages sizes for DMA.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When NPIV port destroy handler is called it does not do all the cleanup
required for the given NPIV port. This was happening as some of the
lport cleanup moved to fcoe_interface_cleanup() routine, which is not
called as part of the vport delete process.
This patch rearranges the sequence in which the fcoe_if_destory() and
fcoe_interface_cleanup() functions are being called from various places
in the code. It now matches the sequence they are constructed during the
create process for both N_Port as well as NPIV port.
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Post an FCH_EVT_LIPRESET event on lport reset as
as lport reset occurs on FIP cleat virtual link,
this could be due to change in fcoe vlan and this
event will allow user app fcoemon to switch to
new fcoe vlan.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
to be deleted.
Problem: After fixing the issue in TCM core w.r.t LUN Reset (Task
Management request) , ran into issue where during the completing of
this LUN Reset command, reference count of "ft_sess" drops to zero
which caused "sess" to be deleted.
Fix: As part of handling task management request (e.g. LUN Reset), TCM
core function "transport_generic_do_tmr" ends up calling ft_free_cmd
which in turn calls "ft_sess_put" (which drops session's reference
count by 1) and then frees ft_cmd. Then function
"transport_generic_do_tmr" calls "transport_cmd_check_stop" which in
turn also calls ft_free_cmd (which calls ft_sess_put - which drops
reference count of sess by 1, hence reference count of sess becomes
zero and session gets deleted). Fix is to just send response in case
of tmr from function "ft_queue_resp_code" and not delete "ft_cmd"
(means don't call ft_free_cmd). Earlier code was to send the response
code and also free ft_cmd. ft_free_cmd will be freed later after
sending response code as a result of "transport_cmd_check_stop" (which
calls ft_release_cmd -> ft_free_cmd) being called from
"transport_generic_do_tmr" after sening TMR response code.
Notes/Dependencies: This bug was found after fixing NULL pointer
access issue in TCM core (in LUN Reset codepath)
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
target and connected to windows initaitor
Problem: Linux based SW target (TCM) connected to windows initiator
was unable to satisfy write request of size > 2K.
Fix: Existing linux implememtation of FCoE stack is expecting sequence
number to match w.r.t incoming framme. When DDP is used on target in
response to write request from initiator, SW stack is notified only
when last data frame arrives and only the pakcket header of last data
frame is posted to NetRx queue of storage. When that last packet was
processed in libfc:Exchange layer, implementation was expecting
sequence number to match, but in this case sequence number which is
embedded in FC Header is assigned by windows initaitor, hence due to
sequence number mismatch post-processing which shall result into
sending RSP is not done. Enhanced the code to utilize the sequence
number of incoming last frame and process the packet so that, it will
eventually complete the write request by sending write response (RSP)
GOOD.
Notes/Dependencies: This patch is validated using windows and linux
initiator to make sure, it doesn't break anything.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
post processing of incoming request for FCoE target
Problem: Selection of RX queue on target is based on RX-ID. FCoE used
8 Net Rx queues. HW post the packets based on rx_id %
num_rx_queue. Due to this has based filtering, only one CPU is busy
servicing incoming request including post-processing of incoming
request. This is gating factor because
1. Only one CPU is utilized 100% while others CPUs are not used at all.
2. CPU which received request assign "sequence' by selecting exchange
from per CPU pool (num_ddp_context / num_online_cpus,
approxi.). Due to which if if rate of incoming request is higher
than rate of servicing request, existing code path end of sending
"BUSY" response (SAM_STAT_BUSY because unable to allocate
exchange).
Fix: Fan-out incoming request to all other CPUs excluding the CPU
which is receiving all incoiming request. This path also addresses,
selecting same CPU based on rx_id from received frame for completion
of the request such as "releasing exchange to the per CPU Pool". This
fix is applicable for FCoE target since initiator code path already
takes care of selecting CPU to complete post-processing of request
once OX_ID is assigned.
Notes: N/A
Dependencines: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
incoming commands
Problem: Earlier mechanism of selection of CPU was, to select the same CPU
which has received incoming request. Hence in case of rx_id = 0xFFFF,
request was always posted to same NetRx queue, hence only 1 CPU is utilized
for handling the command. It was also causing problem of "running out of
exchanges from per CPU pool of exchanges (in case of DDP offload)
Fix: Implemented new algo. to select CPU for post-processing of
incoming commands when rx_id is unknown. This is simple Round robin
algo. for CPU selection.
Notes/Dependencies: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
targets
Problem: When initiator sends write command to target, target tries to
assign new sequence. It allocates new exchangeID (RX_ID)
always from non-offloaded pool (Non-offload EMA)
Fix: Enhanced fcoe_oem_match routine to look at F_CTL flags and if it
is exchange responder and command type is WRITEDATA, then function
returns TRUE instead of FALSE. This function is used to determine
which pool to use (offload pool of exchange is used only if this
function returns TRUE).
Technical Notes: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add ddp_target() support to the Open-FCoE sw fcoe hba driver (fcoe.ko).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
FCoE DDP in target mode
The fcoe driver can implement ddp_targ() similarly to ddp_setup() when fcoe
stack works with existing target frame, e.g., tcm, where the ddp_targ() would
eventually point to the underlying hardware driver's implementation of
ndo_fcoe_ddp_targ() through net_device_ops. This new API sets up DDP context
for target appropriately by setting required bits for DDP context.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Problem: Existing RPORT state machine continues witg FLOGI/PLOGI
process only after it receices beacon from other end. Once claiming
stage is over (either clain notify or clain repose), beacon is sent
and state machine enters into operational mode where it initiates the
rlogin process (FLOGI/PLOGI) to the peer but before this rlogin is
initiated, exitsing implementation checks if it received beacon from
other end, it beacon is not received yet, rlogin process is not
initiated. Other end initiates FLOGI but peer end keeps on rejecting
FLOGI, hence after 3 retries other end deletes associated rport, then
sends a beacon. Once the beacon is received, peer end now initiates
rlogin to the peer end but since associated rport is deleted FLOGI is
neither accepted nor the reject response send out because rport is
deleted. Hence unable to proceed withg FLOGI/PLOGI process and fails
to establish VN2VN connection.
Fix: VN2VN spec is not standard yet but based on exitsing collateral
on T11, it appears that, both end shall send beacon and enter into
'operational mode' without explictly waiting for beacon from other
end. Fix is to allow the RPORT login process as long as respective
RPORT is created (as part of claim notification / claim response) even
though state of RPORT is INIT. Means don't wait for beacon from peer
end, if peer end initiates FLOGI (means peer end exist and
responding).
Notes: This patch is preparing the FCoE stack for target wrt
offload. This is generic patch and harmless even if applied on storage
initiator because 'else if' condition of function 'fcoe_oem_found'
shall evaluate to TRUE only for targets.
Dependencies: None
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
shutdown call
Driver should not call shutdown call from _scsih_remove otherwise,
The scsi midlayer can be deadlocked when devices are removed from the driver
pci_driver->shutdown handler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Properly handling of target reset in multi-initiator environment
Clean up in broadcast change handling:
(1) Need to look at the status of each task management request, and retry
the TM when there are failures.
(2) Need quiescence IO so the driver doesn't take on more IO request while
it's in the middle of sending TM request to firmware
(3) Add support to keep track of how many pending broadcast AEN events
are received while the broadcast handling is active, then loop back at
the end of this routine if there were any events received.
Clean up in mpt2sas_scsih_issue_tm routine:
(1) Make sure proper status is returned when host reset fails
(2) Clean up sanity checks near end of routine, insuring all outstanding
IOs were completed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This feature is to override the default
max_sectors setting at load time, taking max_sectors as an
command line option when loading the driver. The setting is
currently hard-coded in the driver to 8192 sectors (4MB transfers).
If max_sectors is specified at load time, minimum specified
setting will be 64, and the maximum is 8192. The driver will
modify the setting to be on even boundary. If max_sectors is not
specified, the driver will default to 8192.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
mpt2sas driver revision q header update:
(1) Modified the descriptions of the LocalAddress bit in the
Flags field of the MPI SGE Format description and the MPI
Simple Element.
(2) Modified Data Location Address Space bits in the Flags field
of the IEEE Chain Element.
(3) Added more detail to the description of the DataLength field
for the SCSI IO Request and Target Assist Request. Removed
restriction on using chained SGLs when using multicast or
bidirectional support.
(4) In Manufacturing Page 7, added ReceptacleID field to
ConnectorInfo, and reworked how the Pinout field is used.
(5) In IO Unit Page 7, added BoardTemperature and
BoardTemperatureUnits fields.
(6) In IOC Page 1, changed CoalescingTimeout to units of
half-microsecond and updated descriptions.
(7) Modified descriptions of SATASlumberTimeout and
SASSlumberTimeout fields in SAS IO Unit Page 5 to indicate
the timers start after partial mode is entered.
(8) Added Extended Manufacturing configuration pages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch addresses many endian issues solved by runing sparse with the
option __CHECK_ENDIAN__ turned on.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Driver was incorrectly using the SLAB_CACHE_DMA flag when creating a cache
for SGLs. fnic device does not have 24-bit DMA restrictions. Remove the flag
and allocations from ZONE_DMA.
Thanks to Roland Dreier and David Rientjes for pointing out the bug.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added BSG interface support to BFA driver
- Adds support to send ELS/CT FC passthru commands and
few vendor specific BSG requests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Moved FCS initialization, which internally does the im_port creation
as well as the scsi_host creation before bfa_init.
Once the bfa_init is complete & successful:
- Reset the FCS base port cfg params such as pwwn/nwwn and setup fc host
params - based on the values learned during the ioc getattr request.
- Change needed to support BSG commands even on bfa init failure.
- Model description fixes for Brocade adapters.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
from a free IOtag pool.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fixes.
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
when asic blck is programmed flash controller's continuous access
blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
initialization, since not doing so will cause LPU to be
uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduced IOC poll mechanism which replaces current interrupt
based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
1. Use the queue_process flag to see if iocfc configuration is done
in INTX mode.
2. Split the MSIX handler installation in two - one for IOC intr
handler and the other for cpe/rme queue handler - and delay
assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes:
drivers/scsi/sun3_NCR5380.c:475: warning: ‘merge_contiguous_buffers’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes a.o.:
drivers/scsi/sun3_scsi.h:225:5: warning: "NDEBUG" is not defined
drivers/scsi/sun3_scsi.h:345:14: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/sun3_scsi.h:351:14: warning: "NDEBUG_TAGS" is not defined
drivers/scsi/sun3_scsi.h:357:14: warning: "NDEBUG_MERGING" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes:
drivers/scsi/sun3_NCR5380.c:1448:5: warning: "NCR_TIMEOUT" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
and call it from sun3scsi_release(), cfr. the other NCR5380 drivers.
This fixes:
drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
WARNING: vmlinux.o(.text+0x18545c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x18556c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187692): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187770): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
