| Age | Commit message (Collapse) | Author |
|---|
|
The check for infoframe transmit status in hdmi_infoframe_uptodate()
makes the assumption that packet buffer index is set to zero.
Align code with specification and explicitly set the index before
AC_VERB_GET_HDMI_DIP_XMIT. The packet index setting affects both
DIP-Data and DIP-XmitCtrl verbs.
There are no known cases where the old implementation has caused driver
to work incorrectly. This change is purely based on code review against
the specification (HDA spec rev1.0a).
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211131613.3271407-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The debug prints from patch_hdmi.c are not aligned with HDA common code
in hda_codec.c nor with other HDA codec drivers.
To align with rest of the codebase, use hexadecimal formatting whenever
printing value of a HDA NID. Also refer to NIDs with capital letters in
traces as is done other modules. This presentation is also aligned with
the formatting used in HDA codec procfs entry.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201211124547.3243871-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now that the DSP's audio configuration is understood, remove previous
hacky methods of trying to properly configure it.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-6-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Make sure that the DSP has no DMA channels allocated once the firmware
is downloaded, and that the default audio streams in use by the DSP are
setup in the correct order.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-5-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add functions for both reading and writing to the 8051's exram. Also,
add a little bit of documentation on how the addresses are segmented.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-4-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add function for remapping a ChipIO stream's ports. Also include some
documentation as to how this works.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-3-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Reset the codec upon initialization to clear out anything that may have
been setup on a previous boot into Windows, or in case of an improper
shutdown.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201210160658.461739-2-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A problem exists in enabling silent stream when connection type is
DisplayPort. Silent stream programming is completed when a new DP
receiver is connected, but infoframe transmission does not actually
start until PCM is opened for the first time. This can result in audible
gap of multiple seconds. This only affects the first PCM open.
Fix the issue by properly assigning a converter to the silent stream,
and modifying the required stream ID programming sequence.
This change only affects Intel display audio codecs.
BugLink: https://github.com/thesofproject/linux/issues/2468
Fixes: 951894cf30f4 ("ALSA: hda/hdmi: Add Intel silent stream support")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201210174445.3134104-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change the Input Source enumerated control's strings to make it play
nice with pulseaudio.
Fixes: 7cb9d94c05de9 ("ALSA: hda/ca0132: add alt_select_in/out for R3Di + SBZ")
Cc: <stable@kernel.org>
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201208195223.424753-2-conmanx360@gmail.com
Link: https://lore.kernel.org/r/20201210173550.2968-2-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Windows driver sets the pincfg for the AE-5's rear-headphone to
report as a microphone. This causes issues with Pulseaudio mistakenly
believing there is no headphone plugged in. In Linux, we should instead
set it to be a headphone.
Fixes: a6b0961b39896 ("ALSA: hda/ca0132 - fix AE-5 pincfg")
Cc: <stable@kernel.org>
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20201208195223.424753-1-conmanx360@gmail.com
Link: https://lore.kernel.org/r/20201210173550.2968-1-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Steinberg UR22 (with USB ID 0499:1509) requires the implicit feedback
for the proper playback, otherwise it causes occasional cracks.
This patch adds the corresponding the quirk table entry with the
recently added generic implicit fb support.
Reported-and-tested-by: Kilian <meschi@posteo.de>
Link: https://lore.kernel.org/r/20201209161835.13625-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It seems that the HD-audio clear and reconfig sysfs don't work any
longer after the recent driver core change. There are multiple issues
around that: the linked list corruption and the dead device handling.
The former issue is fixed by another patch for the driver core itself,
while the latter patch needs to be addressed in HD-audio side.
This patch corresponds to the latter, it recovers those broken
functions by replacing the device detach and attach actions with the
standard core API functions, which are almost equivalent with unbind
and bind actions.
Fixes: 654888327e9f ("driver core: Avoid binding drivers to dead devices")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209207
Link: https://lore.kernel.org/r/20201209150119.7705-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To help in debugging issues with DisplayPort Multi-Stream Transport (aka
DP-MST) support, print information of active connections for each device
of a display audio pin widget.
Example output with the patch with two monitors connected to a DP-MST hub:
Devices: 4
Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
Dev 01: PD = 1, ELDV = 1, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
*Dev 02: PD = 1, ELDV = 1, IA = 0, Connections [ 0x03 0x05* 0x07 0x09 ]
Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x03* 0x05 0x07 0x09 ]
Connection: 4
0x03 0x05* 0x07 0x09
Format of existing "Connection:" entry is left intact to keep
compatibility.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201208185736.2877541-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The runtime->avail field may be accessed concurrently while some
places refer to it without taking the runtime->lock spinlock, as
detected by KCSAN. Usually this isn't a big problem, but for
consistency and safety, we should take the spinlock at each place
referencing this field.
Reported-by: syzbot+a23a6f1215c84756577c@syzkaller.appspotmail.com
Reported-by: syzbot+3d367d1df1d2b67f5c19@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201206083527.21163-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The snd_seq_queue struct contains various flags in the bit fields.
Those are categorized to two different use cases, both of which are
protected by different spinlocks. That implies that there are still
potential risks of the bad operations for bit fields by concurrent
accesses.
For addressing the problem, this patch rearranges those flags to be
a standard bool instead of a bit field.
Reported-by: syzbot+63cbe31877bb80ef58f5@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20201206083456.21110-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Yet another quirk for Pioneer DJ DDJ-SR2, which is quite similar like
other DJ DDJ models but with slightly different EPs or channels.
Reported-by: Geraldo <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/20201130083714.10640-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The macro use will already have a semicolon.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201127192312.2861127-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The check for the FW_FEATURE_PS3_LV1 firmware feature is already performed
in ps3_system_bus_init() before registering the driver. So if the probe
function is actually used, this feature is already known to be available.
The check for the match id is also superfluous; the condition is always
true because the bus' match function (ps3_system_bus_match()) only
considers this driver for devices having:
dev->match_id == snd_ps3_bus_driver_info.match_id.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Leonard Goehrs <l.goehrs@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Geoff Levand <geoff@infradead.org>
Link: https://lore.kernel.org/r/20201127152259.1470079-1-l.goehrs@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The remove callback is only called for devices that were probed
successfully before. As the matching probe function cannot complete
without error if dev->match_id != PS3_MATCH_ID_SOUND, we don't have to
check this here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geoff Levand <geoff@infradead.org>
Link: https://lore.kernel.org/r/20201126165950.2554997-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch allows the Pioneer DJ DDJ-RR to be seen as a USB audio
device under Linux and therefore usable in such applications as
Mixxx.
Tested Master Audio out, headphones (both output jacks) and microphone
input. All work perfectly.
Signed-off-by: Daniel Martin <dmanlfc@gmail.com>
Link: https://lore.kernel.org/r/20201128084035.2958-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The setup of unsolicited event callbacks should be done only once at
the parser phase, not in the init phase that is called multiple times
at each resume.
This patch moves the unsol setup code in ca0132 codec driver to the
more appropriate place.
Reported-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200930113008.9307-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With a stream with low bitrate, user can't pause or resume the stream
near the end of the stream because current ALSA doesn't allow it.
If the stream has very low bitrate enough to store whole stream into
the buffer, user can't do anything except stop the stream and then
restart it from the first because most of applications call draining
after sending last frame to the kernel.
If pause, resume are allowed during draining, user experience can be
enhanced.
To prevent malfunction in HW drivers which don't support pause
during draining, pause during draining will only work if HW driver
enable this feature explicitly by calling
snd_compr_use_pause_in_draining().
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/000101d6c3f0$89b312b0$9d193810$@samsung.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull the USB audio improvement
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now that the usb audio driver correctly finds implicit feedback endpoints,
the implicit feedback quirk for the MOTU M-Series is no longer required.
This also removes some unnecessary vendor specific messages from the MOTU
M-Series boot quirk. The removed vendor specific messages turned on vendor
specific interrupts to the host every 32 samples. The only thing the boot
quirk needs to do is wait for 2 seconds.
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Signed-off-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-42-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A few other BOSS devices (BR-80, GT-100v2, Katana) seem requiring the
same quirk as BOSS GT-001, i.e. no implicit feedback for playback but
tying with capture. Add and correct the corresponding quirk table
entries for them.
Reported-and-tested-by: Keith Milner <kamilner@superlative.org>
Link: https://lore.kernel.org/r/20201123085347.19667-41-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A new module option, implicit_fb, is added to specify the driver
looking for the implicit feedback sync. This can be useful for a
device that could be working better in the implicit feed back mode and
user wants to test it quickly. When this works, we can add the quirk
entry easily.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-40-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch extends the implicit feedback mode parser code to check the
description more generically, so that the quirk entries can be added
without the explicit EP and interface numbers. The search is done for
the next and the previous interface of the given altset, and if both
entries are ASYNC mode and the direction matches, it just takes as the
sync endpoint. The generic parser is applicable only for the playback
stream.
As of now, only a few M-Audio devices have been converted to use this
mode.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-39-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The code dealing with the implicit feedback mode grew recently, and
it's becoming messy. As we receive more and more devices that need
the similar handling, it's better to be processed through a table
instead of the open code.
This patch moves the code that is relevant with parsing the implicit
feedback mode and some helpers into another file, implicit.c. The
detection and the setup of the implicit feedback sync EPs are
rewritten to use the ID/class matching table instead.
There should be no functional changes.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-38-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The capture stream of BOSS GT-001 seems always requiring to be tied
with the playback stream. OTOH, the playback stream of this device
doesn't seem working in the implicit fb mode, per se, since the
playback must be running before the capture stream.
This patch tries to address the points above:
- Avoid the implicit fb mode for the playback
- Set up a fake sync EP for the capture stream with the hard-coded
playback stream using the implicit fb mode
Reported-by: Keith Milner <kamilner@superlative.org>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-37-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now the sync endpoints have been parsed at the beginning and won't be
changed dynamically, let's show them in the proc outputs for helping
debugging.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-36-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Just for consistency, use unsigned char for iface and altsetting in
allover places. Also rearrange the field positions of
snd_usb_endpiont and tidy up with some comments.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-35-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Follow the inclusive terminology, just replace sync_master/sync_slave
with sync_source/sync_sink. It's also a bit clearer from its meaning,
too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-34-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are multiple places in format.c performing the similar code for
setting the rate_min, rate_max and rates fields. This patch unifies
those in a helper function and calls it at the end of the parser phase
so that all rate_table entries have been already determined.
No functional changes, just a minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-33-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are two places calculating the next packet size for the playback
stream in the exactly same way. Provide the single helper for this
purpose and use it from both places gracefully.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-32-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some fields like interface and alt_idx in snd_usb_substream are mostly
useless now as they can be referred via either cur_audiofmt or
data_endpoint assigned to the substream. Drop those, and also assure
the concurrency about the access of cur_audiofmt field.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-31-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Minor code refactoring to consolidate the URB deactivation code in
endpoint.c. A slight behavior change is that the error handling in
snd_usb_endpoint_start() leaves EP_FLAG_STOPPING now. This should be
synced with the later PCM sync_stop callback.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-30-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The endpoint objects may be started/stopped concurrently by different
substreams in the case of implicit feedback mode, while the current
code handles the reference counter without any protection.
This patch changes the refcount to atomic_t for avoiding the
inconsistency. We need no reference_t here as the refcount goes only
up to 2.
Also the name "use_count" is renamed to "running" since this is about
actually the running status, not the open refcount.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The implicit feedback mode uses a ring buffer for storing the received
packet sizes from the feedback source, and the code has a slight flaw;
when a playback stream stalls by some reason and the URBs aren't
processed, the next_packet FIFO might become empty, but the driver
can't distinguish whether it's empty or full because it's managed with
read_poss and write_pos.
This patch addresses those by changing the next_packet array
management. Instead of keeping read and write positions, now the head
position and the queued amount are kept. It's easier to understand
about the emptiness. Also, the URB active flag is now cleared before
calling queue_pending_output_urbs() for avoiding (theoretically)
possible inconsistency.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is an intensive surgery for the endpoint and stream management
for achieving more robust and clean code.
The goals of this patch are:
- More clear endpoint resource changes
- The interface altsetting control in a single place
Below are brief description of the whole changes.
First off, most of the endpoint operations are moved into endpoint.c,
so that the snd_usb_endpoint object is only referred in other places.
The endpoint object is acquired and released via the new functions
snd_usb_endpoint_open() and snd_usb_endpoint_close() that are called
at PCM hw_params and hw_free callbacks, respectively. Those are
ref-counted and EPs can manage the multiple opens.
The open callback receives the audioformat and hw_params arguments,
and those are used for initializing the EP parameters; especially the
endpoint, interface and altset numbers are read from there, as well as
the PCM parameters like the format, rate and channels. Those are
stored in snd_usb_endpoint object. If it's the secondary open, the
function checks whether the given parameters are compatible with the
already opened EP setup, too.
The coupling with a sync EP (including an implicit feedback sync) is
done by the sole snd_usb_endpoint_set_sync() call.
The configuration of each endpoint is done in a single shot via
snd_usb_endpoint_configure() call. This is the place where most of
PCM configurations are done. A few flags and special handling in the
snd_usb_substream are dropped along with this change.
A significant difference wrt the configuration from the previous code
is the order of USB host interface setups. Now the interface is
always disabled at beginning and (re-)enabled at the last step of
snd_usb_endpoint_configure(), in order to be compliant with the
standard UAC2/3. For UAC1, the interface is set before the parameter
setups since there seem devices that require it (e.g. Yamaha THR10),
just like how it was done in the previous driver code.
The start/stop are almost same as before, also single-shots. The URB
callbacks need to be set via snd_usb_endpoint_set_callback() like the
previous code at the trigger phase, too.
Finally, the flag for the re-setup is set at the device suspend
through the full EP list, instead of PCM trigger. This catches the
overlooked cases where the PCM hasn't been running yet but the device
needs the full setup after resume.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The function to evaluate the match of the parameters with an EP
assumes only the discrete rate tables and doesn't handle the
continuous rates properly.
This patch fixes match_endpoint_audioformats() to handle the
continuous rates. Also the almost useless debug prints there are
dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit 92adc96f8eec ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The prepare_data_urb and retire_data_urb fields of the endpoint object
are set dynamically at PCM trigger start/stop. Those are evaluated in
the endpoint handler, but there can be a race, especially if two
different PCM substreams are handling the same endpoint for the
implicit feedback case. Also, the data_subs field of the endpoint is
set and accessed dynamically, too, which has the same risk.
As a slight improvement for the concurrency, this patch introduces the
function to set the callbacks and the data in a shot with the memory
barrier. In the reader side, it's also fetched with the memory
barrier.
There is still a room of race if prepare and retire callbacks are set
during executing the URB completion. But such an inconsistency may
happen only for the implicit fb source, i.e. it's only about the
capture stream. And luckily, the capture stream never sets the
prepare callback, hence the problem doesn't happen practically.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
start_endpoints() may leave the data endpoint running if an error
happens at starting the sync endpoint. We should stop both streams
properly, instead.
While we're at it, move the debug prints into the endpoint.c that is a
more suitable place.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Setting the active altsetting at changing sample rate seems
unrecommended. The host should deselect the altsetting at first
before that, then select it again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-18-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a helper function to retrieve the usb_host_interface object from
the given interface and altsetting number pair, which is a commonly
used procedure in the driver code.
No functional changes, just minor code refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-17-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This behavior turned out to be invalid from the USB spec POV and
shouldn't be applied. As it's an optional flag that is set only via
an card control element that must be hardly used, let's drop it
again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
