| Age | Commit message (Collapse) | Author |
|---|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
|
|
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
For imx27, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock handling
code any more. Without this patch, it will cause below data
abort when accessing usbmisc registers.
usbcore: registered new interface driver usb-storage
Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600
pgd = c0004000
[f4424600] *pgd=10000452(bad)
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089
Hardware name: Freescale i.MX27 (Device Tree Support)
task: c7832b60 ti: c783e000 task.ti: c783e000
PC is at usbmisc_imx27_init+0x4c/0xbc
LR is at usbmisc_imx27_init+0x40/0xbc
pc : [<c03cb5c0>] lr : [<c03cb5b4>] psr: 60000093
sp : c783fe08 ip : 00000000 fp : 00000000
r10: c0576434 r9 : 0000009c r8 : c7a773a0
r7 : 01000000 r6 : 60000013 r5 : c7a776f0 r4 : c7a773f0
r3 : f4424600 r2 : 00000000 r1 : 00000001 r0 : 00000001
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc783e190)
Stack: (0xc783fe08 to 0xc7840000)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Acked-by: Shawn Guo <shawnguo@kernel.org>
|
|
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc2
First round of fixes for this -rc cycle. We have the
usual set of miscellaneous fixes. The important
thing here is support for Intel Broxton SoC on dwc3,
some fixes for Rockchip SoCs on dwc2 and a fix on
dwc3 to let it report lower speeds than
USB_SPEED_SUPER.
|
|
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad87 ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The current code tries to allocate memory with GFP_KERNEL at
interrupt context, it would show below warning during the enumeration
when I test it with chipidea hardware, change GFP flag as GFP_ATOMIC
can fix this issue.
[ 40.438237] zero gadget: high-speed config #2: loopback
[ 40.444924] ------------[ cut here ]------------
[ 40.449609] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x108/0x128()
[ 40.461715] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 40.467130] Modules linked in:
[ 40.470216] usb_f_ss_lb g_zero libcomposite evbug
[ 40.473822] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0-rc5-00168-gb730aaf #604
[ 40.481496] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 40.487345] Backtrace:
[ 40.489857] [<80014e94>] (dump_backtrace) from [<80015088>] (show_stack+0x18/0x1c)
[ 40.497445] r6:80b67a80 r5:00000000 r4:00000000 r3:00000000
[ 40.503234] [<80015070>] (show_stack) from [<802e27b4>] (dump_stack+0x8c/0xa4)
[ 40.510503] [<802e2728>] (dump_stack) from [<8002cfe8>] (warn_slowpath_common+0x80/0xbc)
[ 40.518612] r6:8007510c r5:00000009 r4:80b49c88 r3:00000001
[ 40.524396] [<8002cf68>] (warn_slowpath_common) from [<8002d05c>] (warn_slowpath_fmt+0x38/0x40)
[ 40.533109] r8:bcfdef80 r7:bdb705cc r6:000080d0 r5:be001e80 r4:809cc278
[ 40.539965] [<8002d028>] (warn_slowpath_fmt) from [<8007510c>] (lockdep_trace_alloc+0x108/0x128)
[ 40.548766] r3:809d0128 r2:809cc278
[ 40.552401] r4:600b0193
[ 40.554990] [<80075004>] (lockdep_trace_alloc) from [<801093d4>] (kmem_cache_alloc+0x28/0x15c)
[ 40.563618] r4:000080d0 r3:80b4aa8c
[ 40.567270] [<801093ac>] (kmem_cache_alloc) from [<804d95e4>] (ep_alloc_request+0x58/0x68)
[ 40.575550] r10:7f01f104 r9:00000001 r8:bcfdef80 r7:bdb705cc r6:bc178700 r5:00000000
[ 40.583512] r4:bcfdef80 r3:813c0a38
[ 40.587183] [<804d958c>] (ep_alloc_request) from [<7f01f7ec>] (loopback_set_alt+0x114/0x21c [usb_f_ss_lb])
[ 40.596929] [<7f01f6d8>] (loopback_set_alt [usb_f_ss_lb]) from [<7f006910>] (composite_setup+0xbd0/0x17e8 [libcomposite])
[ 40.607902] r10:bd3a2c0c r9:00000000 r8:bcfdef80 r7:bc178700 r6:bdb702d0 r5:bcfdefdc
[ 40.615866] r4:7f0199b4 r3:00000002
[ 40.619542] [<7f005d40>] (composite_setup [libcomposite]) from [<804dae88>] (udc_irq+0x784/0xd1c)
[ 40.628431] r10:80bb5619 r9:c0876140 r8:00012001 r7:bdb71010 r6:bdb70568 r5:00010001
[ 40.636392] r4:bdb70014
[ 40.638985] [<804da704>] (udc_irq) from [<804d64f8>] (ci_irq+0x5c/0x118)
[ 40.645702] r10:80bb5619 r9:be11e000 r8:00000117 r7:00000000 r6:bdb71010 r5:be11e060
[ 40.653666] r4:bdb70010
[ 40.656261] [<804d649c>] (ci_irq) from [<8007f638>] (handle_irq_event_percpu+0x7c/0x13c)
[ 40.664367] r6:00000000 r5:be11e060 r4:bdb05cc0 r3:804d649c
[ 40.670149] [<8007f5bc>] (handle_irq_event_percpu) from [<8007f740>] (handle_irq_event+0x48/0x6c)
[ 40.679036] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:bdb05cc0 r5:be11e060
[ 40.686998] r4:be11e000
[ 40.689581] [<8007f6f8>] (handle_irq_event) from [<80082850>] (handle_fasteoi_irq+0xd4/0x1b0)
[ 40.698120] r6:80b56a30 r5:be11e060 r4:be11e000 r3:00000000
[ 40.703898] [<8008277c>] (handle_fasteoi_irq) from [<8007ec04>] (generic_handle_irq+0x28/0x3c)
[ 40.712524] r7:00000000 r6:80b4aaf4 r5:00000117 r4:80b445fc
[ 40.718304] [<8007ebdc>] (generic_handle_irq) from [<8007ef20>] (__handle_domain_irq+0x6c/0xe8)
[ 40.727033] [<8007eeb4>] (__handle_domain_irq) from [<800095d4>] (gic_handle_irq+0x48/0x94)
[ 40.735402] r9:c080f100 r8:80b4ac6c r7:c080e100 r6:80b67d40 r5:80b49f00 r4:c080e10c
[ 40.743290] [<8000958c>] (gic_handle_irq) from [<80015d38>] (__irq_svc+0x58/0x78)
[ 40.750791] Exception stack(0x80b49f00 to 0x80b49f48)
[ 40.755873] 9f00: 00000001 00000001 00000000 80024320 80b48000 80b4a9d0 80b4a984 80b433e4
[ 40.764078] 9f20: 00000001 807f4680 00000000 80b49f5c 80b49f20 80b49f50 80071ca4 800113fc
[ 40.772272] 9f40: 200b0013 ffffffff
[ 40.775776] r9:807f4680 r8:00000001 r7:80b49f34 r6:ffffffff r5:200b0013 r4:800113fc
[ 40.783677] [<800113d4>] (arch_cpu_idle) from [<8006c5bc>] (default_idle_call+0x28/0x38)
[ 40.791798] [<8006c594>] (default_idle_call) from [<8006c6dc>] (cpu_startup_entry+0x110/0x1b0)
[ 40.800445] [<8006c5cc>] (cpu_startup_entry) from [<807e95dc>] (rest_init+0x12c/0x168)
[ 40.808376] r7:80b4a8c0 r3:807f4b7c
[ 40.812030] [<807e94b0>] (rest_init) from [<80ad7cc0>] (start_kernel+0x360/0x3d4)
[ 40.819528] r5:80bcb000 r4:80bcb050
[ 40.823171] [<80ad7960>] (start_kernel) from [<8000807c>] (0x8000807c)
It fixes commit 91c42b0da8e3 ("usb: gadget: loopback: Fix looping back
logic implementation").
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In commit 734643dfbdde ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59fda ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbdde ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
otg_dev->extcon was referenced before otg_dev was initialized. Fix.
Cc: <stable@vger.kernel.org> # v4.3
Fixes: a2fd2423240f ("usb: phy: omap-otg: Replace deprecated API of extcon")
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e460 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
PCI IDs for Broxton based platforms.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Mostly updates to the perf tool plus two fixes to the kernel core code:
- Handle tracepoint filters correctly for inherited events (Peter
Zijlstra)
- Prevent a deadlock in perf_lock_task_context (Paul McKenney)
- Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
Melo)
- Print full source file paths when using 'perf annotate --print-line
--full-paths' (Michael Petlan)
- Fix 'perf probe -d' when just one out of uprobes and kprobes is
enabled (Wang Nan)
- Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)
- Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
the 'perf test' LLVM entries, when running it in-tree, to
.gitignore (Yunlong Song)
- libbpf error reporting improvements, using a strerror interface to
more precisely tell the user about problems with the provided
scriptlet, be it in C or as a ready made object file (Wang Nan)
- Do not be case sensitive when searching for matching 'perf test'
entries (Arnaldo Carvalho de Melo)
- Inform the user about objdump failures in 'perf annotate' (Andi
Kleen)
- Improve the LLVM 'perf test' entry, introduce a new ones for BPF
and kbuild tests to check the environment used by clang to compile
.c scriptlets (Wang Nan)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
tools include: Add compiler.h to list.h
perf probe: Verify parameters in two functions
perf session: Add missing newlines to some pr_err() calls
perf annotate: Support full source file paths for srcline fix
perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
perf: Fix inherited events vs. tracepoint filters
perf: Disable IRQs across RCU RS CS that acquires scheduler lock
perf test: Do not be case sensitive when searching for matching tests
perf test: Add 'perf test BPF'
perf test: Enhance the LLVM tests: add kbuild test
perf test: Enhance the LLVM test: update basic BPF test program
perf bpf: Improve BPF related error messages
perf tools: Make fetch_kernel_version() publicly available
bpf tools: Add new API bpf_object__get_kversion()
bpf tools: Improve libbpf error reporting
perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
perf annotate: Inform the user about objdump failures in --stdio
perf stat: Make stat options global
perf sched latency: Fix thread pid reuse issue
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single fix to prevent math underflow in the numa balancing code"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Fix math underflow in task_tick_numa()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull liblockdep fixes from Thomas Gleixner:
"Three small patches to synchronize liblockdep with the latest core
changes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: explicitly declare lockdep API we call from liblockdep
tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
tools/liblockdep: remove task argument from debug_check_no_locks_held
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes and updates related to x86:
- Fix the W+X check regression on XEN
- The real fix for the low identity map trainwreck
- Probe legacy PIC early instead of unconditionally allocating legacy
irqs
- Add cpu verification to long mode entry
- Adjust the cache topology to AMD Fam17H systems
- Let Merrifield use the TSC across S3"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Call verify_cpu() after having entered long mode too
x86/setup: Fix low identity map for >= 2GB kernel range
x86/mm: Skip the hypervisor range when walking PGD
x86/AMD: Fix last level cache topology for AMD Fam17h systems
x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq and timer fixes from Thomas Gleixner:
- An irq regression fix to restore the wakeup behaviour of chained
interrupts.
- A timer fix for a long standing race versus timers scheduled on a
target cpu which got exposed by recent changes in the workqueue
implementation.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/PM: Restore system wake up from chained interrupts
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Use proper base migration in add_timer_on()
|
|
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc"
* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pci: depend on ZONE_DMA
ALSA: hda - Simplify phantom jack handling for HDMI/DP
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
ALSA: ctxfi: constify rsc ops structures
ALSA: usb: Add native DSD support for Aune X1S
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
sound: fix check for error condition of register_chrdev()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Found a couple of brown paper bag bugs with the prev pull request
(including a SMP build breakage report from Guenter). Since these are
urgent I also decided to send over a bunch of other pending fixes
which could have otherwise waited an rc or two.
Summary:
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
failure)
- cpu_relax() now compiler barrier for UP as well
- handling of userspace Bus Errors for ARCompact builds"
* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
ARCv2: lib: memcpy: use local symbols
|
|
|
|
cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.
Link: http://lkml.kernel.org/r/53A7D3AA.9020100@synopsys.com
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARCompact and ARCv2 only have ASL, while binutils used to support LSL as
a alias mnemonic.
Newer binutils (upstream) don't want to do that so replace it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)
- So move mem_service exception handler from common code into ARCv2 code.
- In ARCompact code, define mem_service as L2 interrupt handler which
just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com>
Tested-by: Ana Martins <amartins@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's the branch of chrome platform changes for v4.4. Some have been
queued up for the full 4.3 release cycle since I forgot to send them
in for that round (rebased early on to deal with fixes conflicts).
Most of these enable EC communication stuff -- Pixel 2015 support,
enabling building for ARM64 platforms, and a few fixes for memory
leaks.
There's also a patch in here to allow reading/writing the verified
boot context, which depends on a sysfs patch acked by Greg"
* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: Fix i2c-designware adapter name
platform/chrome: Support reading/writing the vboot context
sysfs: Support is_visible() on binary attributes
platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
platform/chrome: cros_ec: Fix leak in sequence_store()
platform/chrome: Enable Chrome platforms on 64-bit ARM
platform/chrome: cros_ec_dev - Add a platform device ID table
platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
platform/chrome: cros_ec_lpc - Use existing function to check EC result
platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull another x86 platform driver update from Darren Hart:
"Support for the unfortunately rather unique ESC key on the Ideapad
Yoga 3 and two DMI matches for rfkill support. Solitary fix for
potential missed errors for asus-wmi. Downgrade a thinkpad_acpi
message to info.
asus-wmi:
- fix error handling in store_sys_wmi()
ideapad-laptop:
- Add Lenovo Yoga 900 to no_hw_rfkill dmi list
- include Yoga 3 1170 in add rfkill whitelist
- add support for Yoga 3 ESC key
thinkpad_acpi:
- Don't yell on unsupported brightness interfaces"
* tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
asus-wmi: fix error handling in store_sys_wmi()
ideapad-laptop: Add Lenovo Yoga 900 to no_hw_rfkill dmi list
ideapad-laptop: include Yoga 3 1170 in add rfkill whitelist
ideapad-laptop: add support for Yoga 3 ESC key
thinkpad_acpi: Don't yell on unsupported brightness interfaces
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"An update to the tsc2005 driver that allows it to also support tsc2004
(basically the same controller, but uses i2c instead of spi bus), and
a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: parkbd - drop bogus __init from parkbd_allocate_serio()
Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
Input: tsc2004 - add support for tsc2004
Input: tsc200x-core - rename functions and variables
Input: tsc2005 - separate SPI and core functions
|
|
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c2f ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f78
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs xattr cleanups from Al Viro.
* 'for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
f2fs: xattr simplifications
squashfs: xattr simplifications
9p: xattr simplifications
xattr handlers: Pass handler to operations instead of flags
jffs2: Add missing capability check for listing trusted xattrs
hfsplus: Remove unused xattr handler list operations
ubifs: Remove unused security xattr handler
vfs: Fix the posix_acl_xattr_list return value
vfs: Check attribute names in posix acl xattr handers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- three fixes tagged for -stable including a crash fix, simple
performance tweak, and an invalid i/o error.
- build regression fix for the nvdimm unit tests
- nvdimm documentation update
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix __dax_pmd_fault crash
libnvdimm: documentation clarifications
libnvdimm, pmem: fix size trim in pmem_direct_access()
libnvdimm, e820: fix numa node for e820-type-12 pmem ranges
tools/testing/nvdimm, acpica: fix flag rename build breakage
|
|
Now that the xattr handler is passed to the xattr handler operations, we
have access to the attribute name prefix, so simplify
f2fs_xattr_generic_list.
Also, f2fs_xattr_advise_list is only ever called for
f2fs_xattr_advise_handler; there is no need to double check for that.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Changman Lee <cm224.lee@samsung.com>
Cc: Chao Yu <chao2.yu@samsung.com>
Cc: linux-f2fs-devel@lists.sourceforge.net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Now that the xattr handler is passed to the xattr handler operations, we
have access to the attribute name prefix, so simplify the squashfs xattr
handlers a bit.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Phillip Lougher <phillip@squashfs.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Now that the xattr handler is passed to the xattr handler operations, we
can use the same get and set operations for the user, trusted, and security
xattr namespaces. In those namespaces, we can access the full attribute
name by "reattaching" the name prefix the vfs has skipped for us. Add a
xattr_full_name helper to make this obvious in the code.
For the "system.posix_acl_access" and "system.posix_acl_default"
attributes, handler->prefix is the full attribute name; the suffix is the
empty string.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: v9fs-developer@lists.sourceforge.net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The xattr_handler operations are currently all passed a file system
specific flags value which the operations can use to disambiguate between
different handlers; some file systems use that to distinguish the xattr
namespace, for example. In some oprations, it would be useful to also have
access to the handler prefix. To allow that, pass a pointer to the handler
to operations instead of the flags value alone.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The vfs checks if a task has the appropriate access for get and set
operations, but it cannot do that for the list operation; the file system
must check for that itself.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The list operations can never be called; they are even documented to be
unused.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Ubifs installs a security xattr handler in sb->s_xattr but doesn't use the
generic_{get,set,list,remove}xattr inode operations needed for processing
this list of attribute handlers; the handler is never called. Instead,
ubifs uses its own xattr handlers which also process security xattrs.
Remove the dead code.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
When a filesystem that contains POSIX ACLs is mounted without ACL support
(-o noacl), the appropriate behavior is not to list any existing POSIX ACL
xattrs. The return value for list xattr handlers in this case is 0, not an
error code: several filesystems that use the POSIX ACL xattr handlers do
not expect the list operation to fail.
Symlinks cannot have ACLs, so posix_acl_xattr_list will never be called for
symlinks in the first place.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The get and set operations of the POSIX ACL xattr handlers failed to check
the attribute names, so all names with "system.posix_acl_access" or
"system.posix_acl_default" as a prefix were accepted. Reject invalid names
from now on.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull VFIO updates from Alex Williamson:
- Use kernel interfaces for VPD emulation (Alex Williamson)
- Platform fix for releasing IRQs (Eric Auger)
- Type1 IOMMU always advertises PAGE_SIZE support when smaller mapping
sizes are available (Eric Auger)
- Platform fixes for incorrectly using copies of structures rather than
pointers to structures (James Morse)
- Rework platform reset modules, fix leak, and add AMD xgbe reset
module (Eric Auger)
- Fix vfio_device_get_from_name() return value (Joerg Roedel)
- No-IOMMU interface (Alex Williamson)
- Fix potential out of bounds array access in PCI config handling (Dan
Carpenter)
* tag 'vfio-v4.4-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: make an array larger
vfio: Include No-IOMMU mode
vfio: Fix bug in vfio_device_get_from_name()
VFIO: platform: reset: AMD xgbe reset module
vfio: platform: reset: calxedaxgmac: fix ioaddr leak
vfio: platform: add dev_info on device reset
vfio: platform: use list of registered reset function
vfio: platform: add compat in vfio_platform_device
vfio: platform: reset: calxedaxgmac: add reset function registration
vfio: platform: introduce module_vfio_reset_handler macro
vfio: platform: add capability to register a reset function
vfio: platform: introduce vfio-platform-base module
vfio/platform: store mapped memory in region, instead of an on-stack copy
vfio/type1: handle case where IOMMU does not support PAGE_SIZE size
VFIO: platform: clear IRQ_NOAUTOEN when de-assigning the IRQ
vfio/pci: Use kernel VPD access functions
vfio: Whitelist PCI bridges
|
|
Pull SMB3 updates from Steve French:
"A collection of SMB3 patches adding some reliability features
(persistent and resilient handles) and improving SMB3 copy offload.
I will have some additional patches for SMB3 encryption and SMB3.1.1
signing (important security features), and also for improving SMB3
persistent handle reconnection (setting ChannelSequence number e.g.)
that I am still working on but wanted to get this set in since they
can stand alone"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
Allow copy offload (CopyChunk) across shares
Add resilienthandles mount parm
[SMB3] Send durable handle v2 contexts when use of persistent handles required
[SMB3] Display persistenthandles in /proc/mounts for SMB3 shares if enabled
[SMB3] Enable checking for continuous availability and persistent handle support
[SMB3] Add parsing for new mount option controlling persistent handles
Allow duplicate extents in SMB3 not just SMB3.1.1
|
