| Age | Commit message (Collapse) | Author |
|---|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
NVRAM depends on RTC_DRV_CMOS
rename platform_driver name "flash" to "sa1100-mtd"
annotate that [fp, #-4] is the saved lr
Use __SPIN_LOCK_UNLOCKED to initialize bad_irq_desc.lock
ARM: OMAP: fix fault in enter_full_retention()
ARM: OMAP: Mask interrupts when disabling interrupts, v2
ARM: OMAP: gptimer min_delta_ns corrected
ARM: OMAP: Fix hsmmc init, v2
ARM: OMAP: Fix omap34xx revision detection for ES3.1
ARM: OMAP: DMA: Fix uninitialized channel flags
ARM: OMAP: Fix race in OMAP2/3 DMA IRQ handling
ARM: OMAP: Fix McBSP spin_lock deadlock
[ARM] 5366/1: fix shared memory coherency with VIVT L1 + L2 caches
[ARM] call undefined instruction exception handler with irqs enabled
[ARM] msm: fix build errors
[ARM] etherh: continue fixing build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: add quota call to ocfs2_remove_btree_range()
ocfs2: Wakeup the downconvert thread after a successful cancel convert
ocfs2: Access the xattr bucket only before modifying it.
configfs: Silence lockdep on mkdir(), rmdir() and configfs_depend_item()
ocfs2: Fix possible deadlock in ocfs2_write_dquot()
ocfs2: Push out dropping of dentry lock to ocfs2_wq
|
|
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
[XFS] Warn on transaction in flight on read-only remount
xfs: Check buffer lengths in log recovery
don't reallocate sxp variable passed into xfs_swapext
|
|
Till VFS can correctly support read-only remount without racing,
use WARN_ON instead of BUG_ON on detecting transaction in flight
after quiescing filesystem.
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Before trying to obtain, read or write a buffer,
check that the buffer length is actually valid. If
it is not valid, then something read in the recovery
process has been corrupted and we should abort
recovery.
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Tested-by: Eric Sesterhenn <snakebyte@gmx.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
libata: add no penalty retry request for EH device handling routines
libata: improve probe failure handling
libata: add @spd_limit to sata_down_spd_limit()
libata: clear dev->ering in smarter way
libata: check onlineness before using SPD in sata_down_spd_limit()
libata: move ata_dev_disable() to libata-eh.c
libata: fix EH device failure handling
sata_nv: ck804 has borked hardreset too
ide/libata: fix ata_id_is_cfa() (take 4)
libata: fix kernel-doc warnings
ahci: add a module parameter to ignore the SSS flags for async scanning
sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
[libata] sata_sil: Fix compilation error with libata debugging enabled
|
|
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count. This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions. As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed. This often leads to consecutive hotplug events
without successful probing.
This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.
As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants. This parameter doesn't get in the way even
when it's too low. The closest possible limit is applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed. Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ata_dev_disable() is about to be more tightly integrated into EH
logic. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.
This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay). Seriously, how diverse can you get with hardreset
behaviors? Anyways, make ck804 use noclassify variant too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When checking for the CFA feature set support, ata_id_is_cfa() tests bit 2 in
word 82 of the identify data instead the word 83; it also checks the ATA/PI
version support in the word 80 (which the CompactFlash specifications have as
reserved), this having no slightest chance to work on the modern CF cards that
don't have 0x848A in the word 0...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix libata kernel-doc warnings:
Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.
This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.
Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:
CC [M] drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2
include/linux/libata.h has the following enabled:
#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP
This fixes the compilation.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: fix per cpu kmem_cache_cpu array memory leak
kmalloc: return NULL instead of link failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched_rt: don't use first_cpu on cpumask created with cpumask_and
sched: fix buddie group latency
sched: clear buddies more aggressively
sched: symmetric sync vs avg_overlap
sched: fix sync wakeups
cpuset: fix possible deadlock in async_rebuild_sched_domains
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits)
V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning
V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio
V4L/DVB (10229): ivtv: fix memory leak
V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming.
V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled
V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo
V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback.
V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged
V4L/DVB (10287): af9015: fix second FE
V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock
V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at ffffffff
V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown
V4L/DVB (10257): em28xx: Fix for KWorld 330U Board
V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97
V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition
V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use
V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings.
V4L/DVB (10243): em28xx: fix compile warning
V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic
V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add text file detailing queue/ sysfs files
bio.h: If they MUST be inlined, then use __always_inline
Fix misleading comment in bio.h
block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
block: fix oops in blk_queue_io_stat()
|
|
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is
using a lot of memory.
Each 'struct module' contains an [NR_CPUS] array of full cache lines.
This patch uses existing infrastructure (percpu_modalloc() &
percpu_modfree()) to allocate percpu space for the refcount storage.
Instead of wasting NR_CPUS*128 bytes (on i386), we now use
nr_cpu_ids*sizeof(local_t) bytes.
On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce
size of module files by about 2 Mbytes. (1Kb per module)
Instead of having all refcounters in the same memory node - with TLB misses
because of vmalloc() - this new implementation permits to have better
NUMA properties, since each CPU will use storage on its preferred node,
thanks to percpu storage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We weren't reclaiming the clusters which get free'd from this function,
so any user punching holes in a file would still have those bytes accounted
against him/her. Add the call to vfs_dq_free_space_nodirty() to fix this.
Interestingly enough, the journal credits calculation already took this into
account.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Acked-by: Jan Kara <jack@suse.cz>
|
|
When two nodes holding PR locks on a resource concurrently attempt to
upconvert the locks to EX, the master sends a BAST to one of the nodes. This
message tells that node to first cancel convert the upconvert request,
followed by downconvert to a NL. Only when this lock is downconverted to NL,
can the master upconvert the first node's lock to EX.
While the fs was doing the cancel convert, it was forgetting to wake up the
dc thread after a successful cancel, leading to a deadlock.
Reported-and-Tested-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
In ocfs2_xattr_value_truncate, we may call b-tree codes which will
extend the journal transaction. It has a potential problem that it
may let the already-accessed-but-not-dirtied buffers gone. So we'd
better access the bucket after we call ocfs2_xattr_value_truncate.
And as for the root buffer for the xattr value, b-tree code will
acess and dirty it, so we don't need to worry about it.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
When attaching default groups (subdirs) of a new group (in mkdir() or
in configfs_register()), configfs recursively takes inode's mutexes
along the path from the parent of the new group to the default
subdirs. This is needed to ensure that the VFS will not race with
operations on these sub-dirs. This is safe for the following reasons:
- the VFS allows one to lock first an inode and second one of its
children (The lock subclasses for this pattern are respectively
I_MUTEX_PARENT and I_MUTEX_CHILD);
- from this rule any inode path can be recursively locked in
descending order as long as it stays under a single mountpoint and
does not follow symlinks.
Unfortunately lockdep does not know (yet?) how to handle such
recursion.
I've tried to use Peter Zijlstra's lock_set_subclass() helper to
upgrade i_mutexes from I_MUTEX_CHILD to I_MUTEX_PARENT when we know
that we might recursively lock some of their descendant, but this
usage does not seem to fit the purpose of lock_set_subclass() because
it leads to several i_mutex locked with subclass I_MUTEX_PARENT by
the same task.
>From inside configfs it is not possible to serialize those recursive
locking with a top-level one, because mkdir() and rmdir() are already
called with inodes locked by the VFS. So using some
mutex_lock_nest_lock() is not an option.
I am proposing two solutions:
1) one that wraps recursive mutex_lock()s with
lockdep_off()/lockdep_on().
2) (as suggested earlier by Peter Zijlstra) one that puts the
i_mutexes recursively locked in different classes based on their
depth from the top-level config_group created. This
induces an arbitrary limit (MAX_LOCK_DEPTH - 2 == 46) on the
nesting of configfs default groups whenever lockdep is activated
but this limit looks reasonably high. Unfortunately, this alos
isolates VFS operations on configfs default groups from the others
and thus lowers the chances to detect locking issues.
This patch implements solution 1).
Solution 2) looks better from lockdep's point of view, but fails with
configfs_depend_item(). This needs to rework the locking
scheme of configfs_depend_item() by removing the variable lock recursion
depth, and I think that it's doable thanks to the configfs_dirent_lock.
For now, let's stick to solution 1).
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
It could happen that some limit has been set via quotactl() and in parallel
->mark_dirty() is called from another thread doing e.g. dquot_alloc_space(). In
such case ocfs2_write_dquot() must not try to sync the dquot because that needs
global quota lock but that ranks above transaction start.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
Dropping of last reference to dentry lock is a complicated operation involving
dropping of reference to inode. This can get complicated and quota code in
particular needs to obtain some quota locks which leads to potential deadlock.
Thus we defer dropping of inode reference to ocfs2_wq.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: linux-ide@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
