aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-05spi: tegra114: use unpacked mode for below 4 bytesSowjanya Komatineni
Packed mode expects minimum transfer length of 4 bytes. This patch fixes this by using unpacked mode for transfers less than 4 bytes. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-05spi: tegra114: set supported bits per wordSowjanya Komatineni
Tegra SPI supports 4 through 32 bits per word. This patch sets bits_per_word_mask accordingly to support transfer with these bits per word. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-05spi: tegra114: dump SPI registers during timeoutSowjanya Komatineni
This patch dumps SPI registers on transfer error or timeout for debug purpose. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-05Merge branch 'spi-5.1' into spi-5.2Mark Brown
2019-04-05spi: tegra114: avoid reset call in atomic contextSowjanya Komatineni
This patch moves SPI controller reset out of spin lock. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-05spi: tegra114: de-assert CS before SPI mode changeSowjanya Komatineni
With SW CS, during the transfer completion CS is de-asserted by writing default command1 register value to SPI_COMMAND1 register. With this both mode and CS state are set at the same time and if current transfer mode is different to default SPI mode and if mode change happens prior to CS de-assert, clock polarity can change while CS is active before transfer finishes. This causes Slave to see spurious clock edges resulting in data mismatch. This patch fixes this by de-asserting CS before writing SPI_COMMAND1 to its default value so through out the transfer it will be in same SPI mode. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-04spi: sh-msiof: Convert to use GPIO descriptorsGeert Uytterhoeven
Convert GPIO chip selects in the Renesas MSIOF SPI driver from legacy GPIO numbers to GPIO descriptors. Notes: - The board file for the SH7724-based Ecovec24 development board now registers a GPIO descriptor lookup, instead of passing a GPIO number through controller_data, - sh_msiof_get_cs_gpios() must release all GPIOs, else spi_get_gpio_descs() cannot claim them during SPI controller registration. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-04spi: bcm2835aux: polling_limit_us can be statickbuild test robot
Fixes: 5fd917afc4bf ("spi: bcm2835aux: make the polling duration limits configurable") Signed-off-by: kbuild test robot <lkp@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-04spi: Add missing error handling for CS GPIOsGeert Uytterhoeven
While devm_gpiod_get_index_optional() returns NULL if the GPIO is not present (i.e. -ENOENT), it may still return other error codes, like -EPROBE_DEFER. Currently these are not handled, leading to unrecoverable failures later in case of probe deferral: gpiod_set_consumer_name: invalid GPIO (errorpointer) gpiod_direction_output: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) gpiod_set_value_cansleep: invalid GPIO (errorpointer) Detect and propagate errors to fix this. Fixes: f3186dd876697e69 ("spi: Optionally use GPIO descriptors for CS GPIOs") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-04spi: spi-gpio: Remove spi->controller_data commentGeert Uytterhoeven
The conversion from GPIO numbers to GPIO descriptors removed the use of spi->controller_data, but forgot to update a comment referring to it. Fixes: 9b00bc7b901ff672 ("spi: spi-gpio: Rewrite to use GPIO descriptors") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: add driver stats to debugfsMartin Sperl
To estimate efficiency add statistics on transfer types (polling and interrupt) used to debugfs. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: sh-msiof: Add reset of registers before starting transferGeert Uytterhoeven
In accordance with hardware specification Ver 1.0, reset register transmission / reception setting before transfer. Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> [geert: Use readl_poll_timeout_atomic()] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: sh-msiof: Use readl_poll_timeout_atomic() instead of open-codingGeert Uytterhoeven
Replace the open-coded loop in sh_msiof_modify_ctr_wait() by a call to the readl_poll_timeout_atomic() helper macro. Suggested-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: lpspi: add missing complete in abort func at dma modeClark Wang
Add the missing complete operations for dma_completion to fix the problem of blocking at the wait_for_completion_interruptible() function when use spi_slave_abort(). Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: gpio: Drop unused pdata copy in struct spi_gpioAndrey Smirnov
Drop unused pdata copy in struct spi_gpio. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: gpio: Simplify SPI_MASTER_NO_TX check in spi_gpio_probe()Andrey Smirnov
Swap branches of the if statement in order to simplify it's logical condition being checked. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: gpio: Add local struct spi_bitbang pointer in spi_gpio_probe()Andrey Smirnov
Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for brevity. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: gpio: Add local struct device pointer in spi_gpio_probe()Andrey Smirnov
Use a local "struct device *dev" in spi_gpio_probe() for brevity. No functional change intended. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: gpio: Drop unused spi_to_pdata()Andrey Smirnov
Spi_to_pdata() is not used anywhere in the code. Drop it. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: make the polling duration limits configurableMartin Sperl
Under some circumstances the default 30 us polling limit is not optimal and may lead to long delays because we are waiting on an interrupt. with this patch we have the possibility to influence this policy. So make this limit (in us) configurable via a module parameters (but also modifyable via /sys/modules/...) Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: setup gpio-cs to output and correct level during setupMartin Sperl
Setup gpio-cs to the correct levels during setup and also make the gpio definitely an output GPIO. This is transparently fixing some badly configured DTs in the process where cs-gpio is set but the gpios are still configured with native cs. It also makes 100% sure that the initial CS levels are as expected - especially on systems with devices on a bus with mixed CS_HIGH/CS_LOW settings. Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: warn in dmesg that native cs is not really supportedMartin Sperl
From personal bad experience (even as the author of the original driver) it shows that native-cs is "somewhat" supported by the spi bus driver when using a buggy device tree. So make sure that the driver is warning in dmesg about this fact that we are running in a not supported mode that may have surprizing limitations. Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: fix driver to not allow 65535 (=-1) cs-gpiosMartin Sperl
The original driver by default defines num_chipselects as -1. This actually allicates an array of 65535 entries in of_spi_register_master. There is a side-effect for buggy device trees that (contrary to dt-binding documentation) have no cs-gpio defined. This mode was never supported by the driver due to limitations of native cs and additional code complexity and is explicitly not stated to be implemented. To keep backwards compatibility with such buggy DTs we limit the number of chip_selects to 1, as for all practical purposes it is only ever realistic to use a single chip select in native cs mode without negative side-effects. Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...") Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: remove dead codeMartin Sperl
Remove dead code that never can get reached, as we limit count to a max of 3. Suggested-by: Hubert Denkmair <h.denkmair@intence.de> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: fix corruptions for longer spi transfersMartin Sperl
On long running tests with a mcp2517fd can controller it showed that on rare occations the data read shows corruptions for longer spi transfers. Example of a 22 byte transfer: expected (as captured on logic analyzer): FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 85 86 87 88 89 8a 8b read by the driver: FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 88 89 8a 00 00 8b 9b To fix this use BCM2835_AUX_SPI_STAT_RX_LVL to determine when we may read data from the fifo reliably without any corruption. Surprisingly the only values ever empirically read in BCM2835_AUX_SPI_STAT_RX_LVL are 0x00, 0x10, 0x20 and 0x30. So whenever the mask is not 0 we can read from the fifo in a safe manner. The patch has now been tested intensively and we are no longer able to reproduce the "RX" issue any longer. Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...") Reported-by: Hubert Denkmair <h.denkmair@intence.de> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: remove dangerous uncontrolled read of fifoMartin Sperl
This read of the fifo is a potential candidate for a race condition as the spi transfer is not necessarily finished and so can lead to an early read of the fifo that still misses data. So it has been removed. Fixes: 1ea29b39f4c812ec ("spi: bcm2835aux: add bcm2835 auxiliary spi device...") Suggested-by: Hubert Denkmair <h.denkmair@intence.de> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: bcm2835aux: unifying code between polling and interrupt driven codeMartin Sperl
Sharing more code between polling and interrupt-driven mode. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: spi-mem: export spi_mem_default_supports_op()Naga Sureshkumar Relli
Export spi_mem_default_supports_op(), so that controller drivers can use this. spi-mem driver already exports this using EXPORT_SYMBOL, but not declared it in spi-mem.h. This patch declares spi_mem_default_supports_op() in spi-mem.h and also removes the static from the function prototype. Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03spi: sh-msiof: Use BIT() and GENMASK()Geert Uytterhoeven
Improve maintainability by converting the register bit, bitmask, and bitfield definitions from hexadecimal constants to constructs using BIT(), GENMASK(), or "val << shift". Suggested-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-02spi: spi-fsl-spi: automatically adapt bits-per-word in cpu modeRasmus Villemoes
Taking one interrupt for every byte is rather slow. Since the controller is perfectly capable of transmitting 32 bits at a time, change t->bits_per-word to 32 when the length is divisible by 4 and large enough that the reduced number of interrupts easily compensates for the one or two extra fsl_spi_setup_transfer() calls this causes. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-02spi: spi-fsl-spi: allow changing bits_per_word while CS is still activeRasmus Villemoes
Commit c9bfcb315104 (spi_mpc83xx: much improved driver) introduced logic to ensure bits_per_word and speed_hz stay the same for a series of spi_transfers with CS active, arguing that The current driver may cause glitches on SPI CLK line since one must disable the SPI controller before changing any HW settings. This sounds quite reasonable. So this is a quite naive attempt at relaxing this sanity checking to only ensure that speed_hz is constant - in the faint hope that if we do not causes changes to the clock-related fields of the SPMODE register (DIV16 and PM), those glitches won't appear. The purpose of this change is to allow automatically optimizing large transfers to use 32 bits-per-word; taking one interrupt for every byte is extremely slow. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-02spi: pxa2xx: Unify remaing prints in pxa2xx_spi_transfer_one()Jarkko Nikula
Use SPI device pointer in the remaining two error and warning prints in pxa2xx_spi_transfer_one() instead of platform device of the controller It make prints in the function uniform and more useful especially the error print here as it can reveal the driver that has mapped the DMA itself and attempts to transfer more than the maximum supported DMA transfer length. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-02spi: pxa2xx: Use struct spi_device directly in pxa2xx_spi_transfer_one()Jarkko Nikula
Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there is no need to access it through the current SPI message pointer. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: add SPI_LSB_FIRST supportSowjanya Komatineni
Tegra SPI controller supports lsb first mode. Default is MSB bit first and on selection of SPI_LSB_FIRST through SPI mode transmission happens with LSB bit first. This patch adds SPI_LSB_FIRST flag to mode_bits and also configures it on request. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: use packed mode for 32 bits per wordSowjanya Komatineni
Fixes: Use packed mode for 32 bits per word transfers to increase performance as each packet is a full 32-bit word. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: spi-fsl-spi: relax message sanity checking a littleRasmus Villemoes
The comment says that we should not allow changes (to bits_per_word/speed_hz) while CS is active, and indeed the code below does fsl_spi_setup_transfer() when the ->cs_change of the previous spi_transfer was set (and for the very first transfer). So the sanity checking is a bit too strict - we can change it to follow the same logic as is used by the actual transfer loop. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: spi-fsl-spi: remove always-true conditional in fsl_spi_do_one_msgRasmus Villemoes
__spi_validate() in the generic SPI code sets ->speed_hz and ->bits_per_word to non-zero values, so this condition is always true. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: reset controller on probeSowjanya Komatineni
Fixes: SPI driver can be built as module so perform SPI controller reset on probe to make sure it is in valid state before initiating transfer. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: configure dma burst size to fifo trig levelSowjanya Komatineni
Fixes: Configure DMA burst size to be same as SPI TX/RX trigger levels to avoid mismatch. SPI FIFO trigger levels are calculated based on the transfer length. So this patch moves DMA slave configuration to happen before start of DMAs. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: flush fifosSowjanya Komatineni
Fixes: Flush TX and RX FIFOs before start of new transfer and on FIFO overflow or underrun errors. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: terminate dma and reset on transfer timeoutSowjanya Komatineni
Fixes: terminate DMA and perform controller reset on transfer timeout to clear the FIFO's and errors. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: fix for unpacked mode transfersSowjanya Komatineni
Fixes: computation of actual bytes to fill/receive in/from FIFO in unpacked mode when transfer length is not a multiple of requested bits per word. unpacked mode transfers fails when the transfer includes partial bytes in the last word. Total words to be written/read to/from FIFO is computed based on transfer length and bits per word. Unpacked mode includes 0 padding bytes for partial words to align with bits per word and these extra bytes are also accounted for calculating bytes left to transfer in the current driver. This causes extra bytes access of tx/rx buffers along with buffer index position crossing actual length where remain_len becomes negative and due to unsigned type, negative value is a 32 bit representation of signed value and transferred bytes never meets the actual transfer length resulting in transfer timeout and a hang. This patch fixes this with proper computation of the actual bytes to fill in FIFO during transmit and the actual bytes to read from FIFO during receive ignoring 0 padded bytes. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: tegra114: clear packed bit for unpacked modeSowjanya Komatineni
Fixes: Clear packed bit when not using packed mode. Packed bit is not cleared when not using packed mode. This results in transfer timeouts for the unpacked mode transfers followed by the packed mode transfers. Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-01spi: pic32: fix dma channels terminationCezary Gapinski
When timeout occurs DMA TX and RX channels should be stopped instead of stopping RX channel twice time. Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-27spi: tegra20-slink: change chip select action orderRandolph Maaßen
To transfer via SPI the tegra20-slink driver first sets the command register, which contains the chip select value, and after that the command2 register, which contains the chip select line. This leads to a small spike in the chip selct 0 line between the set of the value and the selection of the chip select line. This commit changes the order of the register writes so that first the chip select line is chosen and then the value is set, removing the spike. Signed-off-by: Randolph Maaßen <gaireg@gaireg.de> Reviewed-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-26spi: stm32-qspi: add dma supportLudovic Barre
This patch adds the dma support for the stm32-qspi hardware. The memory buffer constraints (lowmem, vmalloc, kmap) are taken into account by framework. In read mode, the memory map is preferred vs dma (due to better throughput). If the dma transfer fails the buffer is sent by polling. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-26spi: stm32-qspi: add spi_master_put in release functionLudovic Barre
This patch adds spi_master_put in release function to drop the controller's refcount. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-25spi: mt7621: Move SPI driver out of stagingStefan Roese
This patch moves the MT7621 SPI driver, which is used on some Ralink / MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to the source code are done in this patch. This driver version was tested successfully on an MT7688 based platform with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so far). This patch also documents the devicetree bindings for the MT7621 SPI device driver. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Rob Herring <robh@kernel.org> Cc: Mark Brown <broonie@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: NeilBrown <neil@brown.name> Cc: Sankalp Negi <sankalpnegi2310@gmail.com> Cc: Chuanhong Guo <gch981213@gmail.com> Cc: John Crispin <john@phrozen.org> Cc: Armando Miraglia <arma2ff0@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-25spi: at91-usart: Remove duplicated checking for spi->bits_per_wordAxel Lin
This checking is already done in __spi_validate_bits_per_word(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-03-25spi: atmel-quadspi: Make atmel_qspi_get_name staticYueHaibing
Fix sparse warning: drivers/spi/atmel-quadspi.c:369:12: warning: symbol 'atmel_qspi_get_name' was not declared. Should it be static? Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-14 08:16:47 +0000