| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
|
|
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Remove inode->i_count manipulation in exofs_new_inode
fs/exofs: typo fix of faild to failed
exofs: Set i_mapping->backing_dev_info anyway
exofs: Cleaup read path in regard with read_for_write
|
|
Commit b40827fa7268 ("x86-32, mm: Add an initial page table for core
bootstrapping") added an include directive which is needless and is
taken care of by a previous one. Remove it.
Caught-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
exofs_new_inode() was incrementing the inode->i_count and
decrementing it in create_done(), in a bad attempt to make sure
the inode will still be there when the asynchronous create_done()
finally arrives. This was very stupid because iput() was not called,
and if it was actually needed, it would leak the inode.
However all this is not needed, because at exofs_evict_inode()
we already wait for create_done() by waiting for the
object_created event. Therefore remove the superfluous ref counting
and just Thicken the comment at exofs_evict_inode() a bit.
While at it change places that open coded wait_obj_created()
to call the already available wrapper.
CC: Dave Chinner <dchinner@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (48 commits)
[S390] topology: export cpu topology via proc/sysinfo
[S390] topology: move topology sysinfo code
[S390] topology: clean up facility detection
[S390] cleanup facility list handling
[S390] enable ARCH_DMA_ADDR_T_64BIT with 64BIT
[S390] dasd: ignore unsolicited interrupts for DIAG
[S390] kvm: Enable z196 instruction facilities
[S390] dasd: fix unsolicited interrupt recognition
[S390] dasd: fix use after free in dbf
[S390] kvm: Fix badness at include/asm/mmu_context.h:83
[S390] cio: fix I/O cancel function
[S390] topology: change default
[S390] smp: use correct cpu address in print_cpu_info()
[S390] remove ieee_instruction_pointer from thread_struct
[S390] cleanup system call parameter setup
[S390] correct alignment of cpuid structure
[S390] cleanup lowcore access from external interrupts
[S390] cleanup lowcore access from program checks
[S390] pgtable: move pte_mkhuge() from hugetlb.h to pgtable.h
[S390] fix SIGBUS handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: Orphan the UWB and WUSB subsystems
uwb: Remove the WLP subsystem and drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
eeepc-wmi: Add cpufv sysfs interface
eeepc-wmi: add additional hotkeys
panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
panasonic-laptop: Handle errors properly if they happen
intel_pmic_gpio: fix off-by-one value range checking
IBM Real-Time "SMI Free" mode driver -v7
Add OLPC XO-1 rfkill driver
Move hdaps driver to platform/x86
ideapad-laptop: Fix Makefile
intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
ideapad: Add param: no_bt_rfkill
ideapad: Change the driver name to ideapad-laptop
ideapad: rewrite the sw rfkill set
ideapad: rewrite the hw rfkill notify
ideapad: use EC command to control camera
ideapad: use return value of _CFG to tell if device exist or not
ideapad: make sure we bind on the correct device
ideapad: check VPC bit before sync rfkill hw status
ideapad: add ACPI helpers
dell-laptop: Add debugfs support
...
|
|
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
|
|
Commit b0ae19811375 ("security: remove unused parameter from
security_task_setscheduler()") broke the build of
arch/mips/kernel/mips-mt-fpaff.c. The function arguments were
unnecessary, not the semicolon ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'ieee1394-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: remove the old IEEE 1394 driver stack
ieee1394: move init_ohci1394_dma to drivers/firewire/
Fix trivial change/delete conflict: drivers/ieee1394/eth1394.c is
getting removed, but was modified by the networking merge.
|
|
Replace the BKL with a mutex to protect the venus_comm structure which
binds the mountpoint with the character device and holds the upcall
queues.
Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that shared inode state is locked using the cii->c_lock, the BKL is
only used to protect the upcall queues used to communicate with the
userspace cache manager. The remaining state is all local and we can
push the lock further down into coda_upcall().
Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We mostly need it to protect cached user permissions. The c_flags field
is advisory, reading the wrong value is harmless and in the worst case
we hit a slow path where we have to make an extra upcall to the
userspace cache manager when revalidating a dentry or inode.
Signed-off-by: Yoshihisa Abe <yoshiabe@cs.cmu.edu>
Signed-off-by: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (75 commits)
Input: wacom - specify Cinitq supported tools
Input: ab8500-ponkey - fix IRQ freeing in error path
Input: adp5588-keys - use more obvious i2c_device_id name string
Input: ad7877 - switch to using threaded IRQ
Input: ad7877 - use attribute group to control visibility of attributes
Input: serio - add support for PS2Mult multiplexer protocol
Input: wacom - properly enable runtime PM
Input: ad7877 - filter events where pressure is beyond the maximum
Input: ad7877 - implement EV_KEY:BTN_TOUCH reporting
Input: ad7877 - implement specified chip select behavior
Input: hp680_ts_input - use cancel_delayed_work_sync()
Input: mousedev - correct lockdep annotation
Input: ads7846 - switch to using threaded IRQ
Input: serio - support multiple child devices per single parent
Input: synaptics - simplify pass-through port handling
Input: add ROHM BU21013 touch panel controller support
Input: omap4-keypad - wake-up on events & long presses
Input: omap4-keypad - fix interrupt line configuration
Input: omap4-keypad - SYSCONFIG register configuration
Input: omap4-keypad - use platform device helpers
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "block: fix accounting bug on cross partition merges"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
|
|
Export the cpu configuration topology via sysinfo. Two new lines are
introduced:
CPU Topology HW: 0 0 0 4 6 4
CPU Topology SW: 0 0 0 0 4 24
The HW line describes the cpu topology nesting levels when the maximum
nesting level is used to get the corresponding SYSIB.
The SW line describes what Linux is actually using. In this case it
supports only two levels (CONFIG_SCHED_BOOK off) and therefore the
hardware folded the two lower levels in the SYSIB response block.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Move the topology sysinfo SYSIB definitions to the proper place in
asm/sysinfo.h where they should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Move cpu topology facility detection to early setup code where it
should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Store the facility list once at system startup with stfl/stfle and
reuse the result for all facility tests.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For the DASD DIAG discipline IO is started through special diagnose
calls. Unsolicited interrupts may contain information about the device
itself. But this information is not needed because the device is not
used directly.
Fix the case that an unimplemented dicipline function may be called
by ignoring unsolicited interrupts for the DIAG disciplin.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Enable PFPO, floating point extension, distinct-operands,
fast-BCR-serialization, high-word, interlocked-access, load/store-
on-condition, and population-count facilities for guests.
(bits 37, 44 and 45).
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The dasd interrupt handler needs to distinguish solicited from
unsolicited interrupts, as unsolicited interrupts may require special
handling (e.g. summary unit checks) and solicited interrupts require
proper error recovery for the failed I/O request.
The interrupt handler needs to check several bit fields in the
interrupt response block (irb) to make this distinction.
So far our check of the status control bits has not been specific
enough, which may lead to a failed request getting just retried
instead of the necessary error recovery.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Writing to /proc/dasd/statistics while the debug level of the
generic dasd debug entry is set to DBF_DEBUG will lead to an
use after free when accessing the debug entry later.
Since for the format string "%s" in the s390 dbf only a pointer
to the string is stored in the debug feature and the buffer used
here is freed afterwards.
To fix this just remove the debug message.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
commit 050eef364ad700590a605a0749f825cab4834b1e
[S390] fix tlb flushing vs. concurrent /proc accesses
broke KVM on s390x. On every schedule a
Badness at include/asm/mmu_context.h:83 appears. s390_enable_sie
replaces the mm on the __running__ task, therefore, we have to
increase the attach count of the new mm.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Function ccw_device_cancel_halt_clear may cause an unexpected kernel
panic if a clear function is currently active at the subchannel for
which it is called. In that case, the iretry counter used to determine
the number of retries is never initialized, leading to an immediate
failure of the function which results in a kernel panic.
Fix this by initializing the iretry counter when the function is
first called. Also replace the kernel panic with a return code: a
single malfunctioning I/O device should not automatically cause a
system-wide kernel panic.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Switch default value of the kernel parameter 'topology' from off to on.
Various performance measurements have finally shown that there are no
(known) regressions anywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Up to now print_cpu_info() uses the cpu address stored in it's local
lowcore to print a message to the console. The cpu address in the
lowcore is (in this case) however not the physical cpu address of the
local cpu. It's the address of the cpu that issued the sigp restart
which started the local cpu.
Fix this by using the store cpu address instruction instead.
It's not that anybody really cares since this is broken since more than
ten years...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The ieee_instruction_pointer can not be read from user space anymore
since git commit 613e1def6b52c399a8b72a5e11bc2e57d2546fb8, the ptrace
interface always returns zero. Remove it from the thread_struct. It
is still present in the user_regs_struct for compatability reasons.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Do the setup of the stack overflow argument for the sixth system
call parameter right before the branch to the system call function.
That simplifies the system call parameter access code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The store-cpu-id instruction has a minimum alignment of 8. Reflect
that in the definition of struct cpuid.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Read external interrupts parameters from the lowcore in the first
level interrupt handler in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Read all required fields for program checks from the lowcore in the
first level interrupt handler in entry[64].S. If the context that
caused the fault was enabled for interrupts we can now re-enable the
irqs in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
All architectures besides s390 have pte_mkhuge() defined in pgtable.h.
So move the function to pgtable.h on s390 as well.
Fixes a compile error introduced with "hugetlb: hugepage migration core"
in linux-next which only happens on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Raise SIGBUS with a siginfo structure. Deliver BUS_ADRERR as si_code and
the address of the fault in the si_addr field.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch adds a notification mechanism to inform ccw drivers
about changes to channel paths, which occured while the device
is online.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Update the subchannel descriptor while resuming from hibernate
in order to obtain current link addresses.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Update the channel path descriptors after hibernation.
This is done unlocked, since we are the only active
task at this time.
Note: chsc_determine_base_channel_path_desc is changed
to use spin_lock_irqsave, since it's called with
interrupts disabled in this case.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Update the channel path descriptor at the beginning of to the
vary_on operation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
chsc_determine_channel_path_desc is called by a wrapper
who allocates a response struct. The response data
is then memcpy'ed to this response struct by
chsc_determine_channel_path_desc.
Change chsc_determine_base_channel_path_desc to use the
global chsc_page and deliver it to the function doing
the actual chsc call. The channel path desriptor is
then directly read from the response data.
As a result we get rid of the additional allocation
for the response struct.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Most wrappers around the channel subsystem call have their own logic
to allocate memory (with proper alignment) or use preallocated or
static memory. This patch converts most users of the channel
subsystem call to use the same preallocated page (proteced by a
spinlock).
Note: The sei_page which is used in our crw handler to call
"store event information" has to coexist, since
a) in crw context, while accessing the sei_page, sleeping is allowed
(which will conflict with the spinlock protection of the chsc_page)
b) in crw context, while accessing the sei_page, channel subsystem
calls are allowed (which itself would require the page).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch fixes:
* kfree vs. free_page usage
* structure definition for determine_css_characteristics
* naming convention for the chsc init function
* deregistration of crw handlers in the cleanup path
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Serialize access to members of struct channel_path with a mutex.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If a ccwdevice is lost during hibernation and a different
ccwdevice is attached to the same subchannel, we will
deregister the old ccw device and register the new one.
Since deregistration is not allowed in this context, we
handle this action later. However, some parts of the
registration process for the new device were started anyway,
so that the old device structure is no longer accessible.
Fix this by deferring both actions to the afterwards
scheduled subchannel event.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
