| Age | Commit message (Collapse) | Author |
|---|
|
The current VFIO_DEVICE_RESET interface only maps to PCI use cases
where we can isolate the reset to the individual PCI function. This
means the device must support FLR (PCIe or AF), PM reset on D3hot->D0
transition, device specific reset, or be a singleton device on a bus
for a secondary bus reset. FLR does not have widespread support,
PM reset is not very reliable, and bus topology is dictated by the
system and device design. We need to provide a means for a user to
induce a bus reset in cases where the existing mechanisms are not
available or not reliable.
This device specific extension to VFIO provides the user with this
ability. Two new ioctls are introduced:
- VFIO_DEVICE_PCI_GET_HOT_RESET_INFO
- VFIO_DEVICE_PCI_HOT_RESET
The first provides the user with information about the extent of
devices affected by a hot reset. This is essentially a list of
devices and the IOMMU groups they belong to. The user may then
initiate a hot reset by calling the second ioctl. We must be
careful that the user has ownership of all the affected devices
found via the first ioctl, so the second ioctl takes a list of file
descriptors for the VFIO groups affected by the reset. Each group
must have IOMMU protection established for the ioctl to succeed.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
|
|
Having PCIe/PCI-X capability isn't enough to assume that there are
extended capabilities. Both specs define that the first capability
header is all zero if there are no extended capabilities. Testing
for this avoids an erroneous message about hiding capability 0x0 at
offset 0x100.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm changes from Ingo Molnar:
"Misc smaller fixes:
- a parse_setup_data() boot crash fix
- a memblock and an __early_ioremap cleanup
- turn the always-on CONFIG_ARCH_MEMORY_PROBE=y into a configurable
option and turn it off - it's an unrobust debug facility, it
shouldn't be enabled by default"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: avoid remapping data in parse_setup_data()
x86: Use memblock_set_current_limit() to set limit for memblock.
mm: Remove unused variable idx0 in __early_ioremap()
mm/hotplug, x86: Disable ARCH_MEMORY_PROBE by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 relocation changes from Ingo Molnar:
"This tree contains a single change, ELF relocation handling in C - one
of the kernel randomization patches that makes sense even without
randomization present upstream"
* 'x86-kaslr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: Move ELF relocation handling to C
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timers/nohz changes from Ingo Molnar:
"It mostly contains fixes and full dynticks off-case optimizations, by
Frederic Weisbecker"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
nohz: Include local CPU in full dynticks global kick
nohz: Optimize full dynticks's sched hooks with static keys
nohz: Optimize full dynticks state checks with static keys
nohz: Rename a few state variables
vtime: Always debug check snapshot source _before_ updating it
vtime: Always scale generic vtime accounting results
vtime: Optimize full dynticks accounting off case with static keys
vtime: Describe overriden functions in dedicated arch headers
m68k: hardirq_count() only need preempt_mask.h
hardirq: Split preempt count mask definitions
context_tracking: Split low level state headers
vtime: Fix racy cputime delta update
vtime: Remove a few unneeded generic vtime state checks
context_tracking: User/kernel broundary cross trace events
context_tracking: Optimize context switch off case with static keys
context_tracking: Optimize guest APIs off case with static key
context_tracking: Optimize main APIs off case with static key
context_tracking: Ground setup for static key use
context_tracking: Remove full dynticks' hacky dependency on wide context tracking
nohz: Only enable context tracking on full dynticks CPUs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fb changes from Ingo Molnar:
"This tree includes preparatory patches for SimpleDRM driver support,
by David Herrmann. They clean up x86 framebuffer support by creating
simplefb devices wherever possible. More background can be found at
http://lwn.net/Articles/558104/"
* 'x86-fb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fbdev: fbcon: select VT_HW_CONSOLE_BINDING
fbdev: efifb: bind to efi-framebuffer
fbdev: vesafb: bind to platform-framebuffer device
fbdev: simplefb: add common x86 RGB formats
x86: sysfb: move EFI quirks from efifb to sysfb
x86: provide platform-devices for boot-framebuffers
fbdev: simplefb: mark as fw and allocate apertures
fbdev: simplefb: add init through platform_data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu feature fixes from Ingo Molnar:
"Two small cpufeature support updates"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix override new_cpu_data.x86 with 486
x86, cpufeature: Use new CC_HAVE_ASM_GOTO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull tiny x86 boot cleanups from Ingo Molnar.
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix a sanity check in printf.c
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix warning due to undeclared strlen()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/asmlinkage changes from Ingo Molnar:
"As a preparation for Andi Kleen's LTO patchset (link time
optimizations using GCC's -flto which build time optimization has
steadily increased in quality over the past few years and might
eventually be usable for the kernel too) this tree includes a handful
of preparatory patches that make function calling convention
annotations consistent again:
- Mark every function without arguments (or 64bit only) that is used
by assembly code with asmlinkage()
- Mark every function with parameters or variables that is used by
assembly code as __visible.
For the vanilla kernel this has documentation, consistency and
debuggability advantages, for the time being"
* 'x86-asmlinkage-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asmlinkage: Fix warning in xen asmlinkage change
x86, asmlinkage, vdso: Mark vdso variables __visible
x86, asmlinkage, power: Make various symbols used by the suspend asm code visible
x86, asmlinkage: Make dump_stack visible
x86, asmlinkage: Make 64bit checksum functions visible
x86, asmlinkage, paravirt: Add __visible/asmlinkage to xen paravirt ops
x86, asmlinkage, apm: Make APM data structure used from assembler visible
x86, asmlinkage: Make syscall tables visible
x86, asmlinkage: Make several variables used from assembler/linker script visible
x86, asmlinkage: Make kprobes code visible and fix assembler code
x86, asmlinkage: Make various syscalls asmlinkage
x86, asmlinkage: Make 32bit/64bit __switch_to visible
x86, asmlinkage: Make _*_start_kernel visible
x86, asmlinkage: Make all interrupt handlers asmlinkage / __visible
x86, asmlinkage: Change dotraplinkage into __visible on 32bit
x86: Fix sys_call_table type in asm/syscall.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/asm changes from Ingo Molnar:
"Main changes:
- Apply low level mutex optimization on x86-64, by Wedson Almeida
Filho.
- Change bitops to be naturally 'long', by H Peter Anvin.
- Add TSX-NI opcodes support to the x86 (instrumentation) decoder, by
Masami Hiramatsu.
- Add clang compatibility adjustments/workarounds, by Jan-Simon
Möller"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, doc: Update uaccess.h comment to reflect clang changes
x86, asm: Fix a compilation issue with clang
x86, asm: Extend definitions of _ASM_* with a raw format
x86, insn: Add new opcodes as of June, 2013
x86/ia32/asm: Remove unused argument in macro
x86, bitops: Change bitops to be native operand size
x86: Use asm-goto to implement mutex fast path on x86-64
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/apic changes from Ingo Molnar:
"Smaller fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioapic: Check attr against the previous setting when programmed more than once
x86/ioapic/kcrash: Prevent crash_kexec() from deadlocking on ioapic_lock
x86/acpi: Fix incorrect sanity check in acpi_register_lapic()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer changes from Ingo Molnar:
"Various clocksource driver updates: extend the core with memory mapped
hardware (mmio) support and add new (ARM) Moxart SoC and sun4i
hardware support"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
clocksource: arch_timer: Add support for memory mapped timers
clocksource: arch_timer: Push the read/write wrappers deeper
Documentation: Add memory mapped ARM architected timer binding
clocksource: arch_timer: Pass clock event to set_mode callback
clocksource: arch_timer: Make register accessors less error-prone
ARM: clocksource: moxart: documentation: Update device tree bindings document
ARM: clocksource: moxart: Add bitops.h include
ARM: clocksource: moxart: documentation: Fix device tree bindings document
ARM: clocksource: Add support for MOXA ART SoCs
clocksource: cadence_ttc: Reuse clocksource as sched_clock
clocksource: cadence_ttc: Remove unused header
clocksource: sun4i: Fix bug when switching from periodic to oneshot modes
clocksource: sun4i: Cleanup parent clock setup
clocksource: sun4i: Remove TIMER_SCAL variable
clocksource: sun4i: Factor out some timer code
clocksource: sun4i: Fix the next event code
clocksource: sun4i: Don't forget to enable the clock we use
clocksource: sun4i: Add clocksource and sched clock drivers
clocksource: sun4i: rename AUTORELOAD define to RELOAD
clocksource: sun4i: Wrap macros arguments in parenthesis
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler changes from Ingo Molnar:
"Various optimizations, cleanups and smaller fixes - no major changes
in scheduler behavior"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix the sd_parent_degenerate() code
sched/fair: Rework and comment the group_imb code
sched/fair: Optimize find_busiest_queue()
sched/fair: Make group power more consistent
sched/fair: Remove duplicate load_per_task computations
sched/fair: Shrink sg_lb_stats and play memset games
sched: Clean-up struct sd_lb_stat
sched: Factor out code to should_we_balance()
sched: Remove one division operation in find_busiest_queue()
sched/cputime: Use this_cpu_add() in task_group_account_field()
cpumask: Fix cpumask leak in partition_sched_domains()
sched/x86: Optimize switch_mm() for multi-threaded workloads
generic-ipi: Kill unnecessary variable - csd_flags
numa: Mark __node_set() as __always_inline
sched/fair: Cleanup: remove duplicate variable declaration
sched/__wake_up_sync_key(): Fix nr_exclusive tasks which lead to WF_SYNC clearing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf changes from Ingo Molnar:
"As a first remark I'd like to point out that the obsolete '-f'
(--force) option, which has not done anything for several releases,
has been removed from 'perf record' and related utilities. Everyone
please update muscle memory accordingly! :-)
Main changes on the perf kernel side:
- Performance optimizations:
. for trace events, by Steve Rostedt.
. for time values, by Peter Zijlstra
- New hardware support:
. for Intel Silvermont (22nm Atom) CPUs, by Zheng Yan
. for Intel SNB-EP uncore PMUs, by Zheng Yan
- Enhanced hardware support:
. for Intel uncore PMUs: add filter support for QPI boxes, by Zheng Yan
- Core perf events code enhancements and fixes:
. for full-nohz feature handling, by Frederic Weisbecker
. for group events, by Jiri Olsa
. for call chains, by Frederic Weisbecker
. for event stream parsing, by Adrian Hunter
- New ABI details:
. Add attr->mmap2 attribute, by Stephane Eranian
. Add PERF_EVENT_IOC_ID ioctl to return event ID, by Jiri Olsa
. Export u64 time_zero on the mmap header page to allow TSC
calculation, by Adrian Hunter
. Add dummy software event, by Adrian Hunter.
. Add a new PERF_SAMPLE_IDENTIFIER to make samples always
parseable, by Adrian Hunter.
. Make Power7 events available via sysfs, by Runzhen Wang.
- Code cleanups and refactorings:
. for nohz-full, by Frederic Weisbecker
. for group events, by Jiri Olsa
- Documentation updates:
. for perf_event_type, by Peter Zijlstra
Main changes on the perf tooling side (some of these tooling changes
utilize the above kernel side changes):
- Lots of 'perf trace' enhancements:
. Make 'perf trace' command line arguments consistent with
'perf record', by David Ahern.
. Allow specifying syscalls a la strace, by Arnaldo Carvalho de Melo.
. Add --verbose and -o/--output options, by Arnaldo Carvalho de Melo.
. Support ! in -e expressions, to filter a list of syscalls,
by Arnaldo Carvalho de Melo.
. Arg formatting improvements to allow masking arguments in
syscalls such as futex and open, where the some arguments are
ignored and thus should not be printed depending on other args,
by Arnaldo Carvalho de Melo.
. Beautify futex open, openat, open_by_handle_at, lseek and futex
syscalls, by Arnaldo Carvalho de Melo.
. Add option to analyze events in a file versus live, so that
one can do:
[root@zoo ~]# perf record -a -e raw_syscalls:* sleep 1
[ perf record: Woken up 0 times to write data ]
[ perf record: Captured and wrote 25.150 MB perf.data (~1098836 samples) ]
[root@zoo ~]# perf trace -i perf.data -e futex --duration 1
17.799 ( 1.020 ms): 7127 futex(uaddr: 0x7fff3f6c6674, op: 393, val: 1, utime: 0x7fff3f6c6470, ua
113.344 (95.429 ms): 7127 futex(uaddr: 0x7fff3f6c6674, op: 393, val: 1, utime: 0x7fff3f6c6470, uaddr2: 0x7fff3f6c6648, val3: 4294967
133.778 ( 1.042 ms): 18004 futex(uaddr: 0x7fff3f6c6674, op: 393, val: 1, utime: 0x7fff3f6c6470, uaddr2: 0x7fff3f6c6648, val3: 429496
[root@zoo ~]#
By David Ahern.
. Honor target pid / tid options when analyzing a file, by David Ahern.
. Introduce better formatting of syscall arguments, including so
far beautifiers for mmap, madvise, syscall return values,
by Arnaldo Carvalho de Melo.
. Handle HUGEPAGE defines in the mmap beautifier, by David Ahern.
- 'perf report/top' enhancements:
. Do annotation using /proc/kcore and /proc/kallsyms when
available, removing the forced need for a vmlinux file kernel
assembly annotation. This also improves this use case because
vmlinux has just the initial kernel image, not what is actually
in use after various code patchings by things like alternatives.
By Adrian Hunter.
. Add --ignore-callees=<regex> option to collapse undesired parts
of call graphs, by Greg Price.
. Simplify symbol filtering by doing it at machine class level,
by Adrian Hunter.
. Add support for callchains in the gtk UI, by Namhyung Kim.
. Add --objdump option to 'perf top', by Sukadev Bhattiprolu.
- 'perf kvm' enhancements:
. Add option to print only events that exceed a specified time
duration, by David Ahern.
. Improve stack trace printing, by David Ahern.
. Update documentation of the live command, by David Ahern
. Add perf kvm stat live mode that combines aspects of 'perf kvm
stat' record and report, by David Ahern.
. Add option to analyze specific VM in perf kvm stat report, by
David Ahern.
. Do not require /lib/modules/* on a guest, by Jason Wessel.
- 'perf script' enhancements:
. Fix symbol offset computation for some dsos, by David Ahern.
. Fix named threads support, by David Ahern.
. Don't install scripting files files when perl/python support
is disabled, by Arnaldo Carvalho de Melo.
- 'perf test' enhancements:
. Add various improvements and fixes to the "vmlinux matches
kallsyms" 'perf test' entry, related to the /proc/kcore
annotation feature. By Adrian Hunter.
. Add sample parsing test, by Adrian Hunter.
. Add test for reading object code, by Adrian Hunter.
. Add attr record group sampling test, by Jiri Olsa.
. Misc testing infrastructure improvements and other details,
by Jiri Olsa.
- 'perf list' enhancements:
. Skip unsupported hardware events, by Namhyung Kim.
. List pmu events, by Andi Kleen.
- 'perf diff' enhancements:
. Add support for more than two files comparison, by Jiri Olsa.
- 'perf sched' enhancements:
. Various improvements, including removing reliance on some
scheduler tracepoints that provide the same information as the
PERF_RECORD_{FORK,EXIT} events. By David Ahern.
. Remove odd build stall by moving a large struct initialization
from a local variable to a global one, by Namhyung Kim.
- 'perf stat' enhancements:
. Add --initial-delay option to skip measuring for a defined
startup phase, by Andi Kleen.
- Generic perf tooling infrastructure/plumbing changes:
. Tidy up sample parsing validation, by Adrian Hunter.
. Fix up jobserver setup in libtraceevent Makefile.
by Arnaldo Carvalho de Melo.
. Debug improvements, by Adrian Hunter.
. Fix correlation of samples coming after PERF_RECORD_EXIT event,
by David Ahern.
. Improve robustness of the topology parsing code,
by Stephane Eranian.
. Add group leader sampling, that allows just one event in a group
to sample while the other events have just its values read,
by Jiri Olsa.
. Add support for a new modifier "D", which requests that the
event, or group of events, be pinned to the PMU.
By Michael Ellerman.
. Support callchain sorting based on addresses, by Andi Kleen
. Prep work for multi perf data file storage, by Jiri Olsa.
. libtraceevent cleanups, by Namhyung Kim.
And lots and lots of other fixes and code reorganizations that did not
make it into the list, see the shortlog, diffstat and the Git log for
details!"
[ Also merge a leftover from the 3.11 cycle ]
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Prevent race in unthrottling code
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (237 commits)
perf trace: Tell arg formatters the arg index
perf trace: Add beautifier for open's flags arg
perf trace: Add beautifier for lseek's whence arg
perf tools: Fix symbol offset computation for some dsos
perf list: Skip unsupported events
perf tests: Add 'keep tracking' test
perf tools: Add support for PERF_COUNT_SW_DUMMY
perf: Add a dummy software event to keep tracking
perf trace: Add beautifier for futex 'operation' parm
perf trace: Allow syscall arg formatters to mask args
perf: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node()
perf: Export struct perf_branch_entry to userspace
perf: Add attr->mmap2 attribute to an event
perf/x86: Add Silvermont (22nm Atom) support
perf/x86: use INTEL_UEVENT_EXTRA_REG to define MSR_OFFCORE_RSP_X
perf trace: Handle missing HUGEPAGE defines
perf trace: Honor target pid / tid options when analyzing a file
perf trace: Add option to analyze events in a file versus live
perf evlist: Add tracepoint lookup by name
perf tests: Add a sample parsing test
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core/locking changes from Ingo Molnar:
"Main changes:
- another mutex optimization, from Davidlohr Bueso
- improved lglock lockdep tracking, from Michel Lespinasse
- [ assorted smaller updates, improvements, cleanups. ]"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
generic-ipi/locking: Fix misleading smp_call_function_any() description
hung_task debugging: Print more info when reporting the problem
mutex: Avoid label warning when !CONFIG_MUTEX_SPIN_ON_OWNER
mutex: Do not unnecessarily deal with waiters
mutex: Fix/document access-once assumption in mutex_can_spin_on_owner()
lglock: Update lockdep annotations to report recursive local locks
lockdep: Introduce lock_acquire_exclusive()/shared() helper macros
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"Main RCU changes this cycle were:
- Full-system idle detection. This is for use by Frederic
Weisbecker's adaptive-ticks mechanism. Its purpose is to allow the
timekeeping CPU to shut off its tick when all other CPUs are idle.
- Miscellaneous fixes.
- Improved rcutorture test coverage.
- Updated RCU documentation"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
nohz_full: Force RCU's grace-period kthreads onto timekeeping CPU
nohz_full: Add full-system-idle state machine
jiffies: Avoid undefined behavior from signed overflow
rcu: Simplify _rcu_barrier() processing
rcu: Make rcutorture emit online failures if verbose
rcu: Remove unused variable from rcu_torture_writer()
rcu: Sort rcutorture module parameters
rcu: Increase rcutorture test coverage
rcu: Add duplicate-callback tests to rcutorture
doc: Fix memory-barrier control-dependency example
rcu: Update RTFP documentation
nohz_full: Add full-system-idle arguments to API
nohz_full: Add full-system idle states and variables
nohz_full: Add per-CPU idle-state tracking
nohz_full: Add rcu_dyntick data for scalable detection of all-idle state
nohz_full: Add Kconfig parameter for scalable detection of all-idle state
nohz_full: Add testing information to documentation
rcu: Eliminate unused APIs intended for adaptive ticks
rcu: Select IRQ_WORK from TREE_PREEMPT_RCU
rculist: list_first_or_null_rcu() should use list_entry_rcu()
...
|
|
Pull pwm changes from Thierry Reding:
"A set of patches makes the device tree documentation for the various
PWM drivers more consistent. Device tree support is added to the
Renesas TPU driver. The sysfs interface now makes use of dev_groups.
Other than that there is a healthy assortment of fixes and
enhancements for minor issues that have shown up"
* tag 'for-3.12-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: pxa: Use module_platform_driver
pwm: tiehrpwm: add missing __iomem annotation
pwm: tiecap: add CONFIG_PM_SLEEP to ecap_pwm_{save,restore}_context()
pwm: simplify use of devm_ioremap_resource
pwm: renesas-tpu: Add DT support
ARM: dts: Use the PWM polarity flags
pwm: Update DT bindings to reference pwm.txt for cells documentation
pwm: Use the DT macro directly when parsing PWM DT flags
pwm: Add PWM polarity flag macro for DT
pwm: mxs: Check the return value from stmp_reset_block()
pwm: convert class code to use dev_groups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull pstore changes from Tony Luck:
"A big part of this is the addition of compression to the generic
pstore layer so that all backends can use the pitiful amounts of
storage they control more effectively. Three other small
fixes/cleanups too.
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore/ram: (really) fix undefined usage of rounddown_pow_of_two
pstore/ram: Read and write to the 'compressed' flag of pstore
efi-pstore: Read and write to the 'compressed' flag of pstore
erst: Read and write to the 'compressed' flag of pstore
powerpc/pseries: Read and write to the 'compressed' flag of pstore
pstore: Add file extension to pstore file if compressed
pstore: Add decompression support to pstore
pstore: Introduce new argument 'compressed' in the read callback
pstore: Add compression support to pstore
pstore/Kconfig: Select ZLIB_DEFLATE and ZLIB_INFLATE when PSTORE is selected
pstore: Add new argument 'compressed' in pstore write callback
powerpc/pseries: Remove (de)compression in nvram with pstore enabled
pstore: d_alloc_name() doesn't return an ERR_PTR
acpi/apei/erst: Add missing iounmap() on error in erst_exec_move_data()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"A lot of activities on the cgroup front. Most changes aren't visible
to userland at all at this point and are laying foundation for the
planned unified hierarchy.
- The biggest change is decoupling the lifetime management of css
(cgroup_subsys_state) from that of cgroup's. Because controllers
(cpu, memory, block and so on) will need to be dynamically enabled
and disabled, css which is the association point between a cgroup
and a controller may come and go dynamically across the lifetime of
a cgroup. Till now, css's were created when the associated cgroup
was created and stayed till the cgroup got destroyed.
Assumptions around this tight coupling permeated through cgroup
core and controllers. These assumptions are gradually removed,
which consists bulk of patches, and css destruction path is
completely decoupled from cgroup destruction path. Note that
decoupling of creation path is relatively easy on top of these
changes and the patchset is pending for the next window.
- cgroup has its own event mechanism cgroup.event_control, which is
only used by memcg. It is overly complex trying to achieve high
flexibility whose benefits seem dubious at best. Going forward,
new events will simply generate file modified event and the
existing mechanism is being made specific to memcg. This pull
request contains prepatory patches for such change.
- Various fixes and cleanups"
Fixed up conflict in kernel/cgroup.c as per Tejun.
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (69 commits)
cgroup: fix cgroup_css() invocation in css_from_id()
cgroup: make cgroup_write_event_control() use css_from_dir() instead of __d_cgrp()
cgroup: make cgroup_event hold onto cgroup_subsys_state instead of cgroup
cgroup: implement CFTYPE_NO_PREFIX
cgroup: make cgroup_css() take cgroup_subsys * instead and allow NULL subsys
cgroup: rename cgroup_css_from_dir() to css_from_dir() and update its syntax
cgroup: fix cgroup_write_event_control()
cgroup: fix subsystem file accesses on the root cgroup
cgroup: change cgroup_from_id() to css_from_id()
cgroup: use css_get() in cgroup_create() to check CSS_ROOT
cpuset: remove an unncessary forward declaration
cgroup: RCU protect each cgroup_subsys_state release
cgroup: move subsys file removal to kill_css()
cgroup: factor out kill_css()
cgroup: decouple cgroup_subsys_state destruction from cgroup destruction
cgroup: replace cgroup->css_kill_cnt with ->nr_css
cgroup: bounce cgroup_subsys_state ref kill confirmation to a work item
cgroup: move cgroup->subsys[] assignment to online_css()
cgroup: reorganize css init / exit paths
cgroup: add __rcu modifier to cgroup->subsys[]
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
|
|
Pull workqueue updates from Tejun Heo:
"Nothing interesting. All are doc / comment updates"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Correct/Drop references to gcwq in Documentation
workqueue: Fix manage_workers() RETURNS description
workqueue: Comment correction in file header
workqueue: mark WQ_NON_REENTRANT deprecated
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull single percpu update from Tejun Heo:
"Just a single patch to update type verification macro for percpu
accessors.
Christoph is trying to replace __get_cpu_var() with this_cpu accessors
which needs this update. There are still some issues to be resolved
but eventually the conversion patches are likely to be routed through
different trees, so I think it'd be convenient to merge this commit
early"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Make __verify_pcu_ptr handle per cpu pointers to arrays
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"The first patch is to address a long standing issue where INQUIRY
vendor + model response data was not correctly padded with ASCII
spaces, causing MSFT and Falconstor multipath stacks to not function
with our LUNs.
The second -> forth patches are additional iscsi-target regression
fixes for the post >= v3.10 iser-target changes. The second and third
are failure cases that have appeared during further testing, and the
forth is only reproducible with malformed NOP packets.
The fifth patch is a v3.11 specific regression caused by a recent
optimization that showed up during WRITE I/O failure testing.
I'll be sending Patch #1 and Patch #5 to Greg-KH separately for
stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix se_cmd->state_list leak regression during WRITE failure
iscsi-target: Fix potential NULL pointer in solicited NOPOUT reject
iscsi-target: Fix iscsit_transport reference leak during NP thread reset
iscsi-target: Fix ImmediateData=Yes failure regression in >= v3.10
target: Fix trailing ASCII space usage in INQUIRY vendor+model
|
|
Pull first round of SCSI updates from James Bottomley:
"This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]).
We also have a new driver: esas2r which has a number of static checker
problems, but which I expect to resolve over the -rc course of 3.12
under the new driver exception.
We also have the error return that were discussed at LSF"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (118 commits)
[SCSI] sg: push file descriptor list locking down to per-device locking
[SCSI] sg: checking sdp->detached isn't protected when open
[SCSI] sg: no need sg_open_exclusive_lock
[SCSI] sg: use rwsem to solve race during exclusive open
[SCSI] scsi_debug: fix logical block provisioning support when unmap_alignment != 0
[SCSI] scsi_debug: fix endianness bug in sdebug_build_parts()
[SCSI] qla2xxx: Update the driver version to 8.06.00.08-k.
[SCSI] qla2xxx: print MAC via %pMR.
[SCSI] qla2xxx: Correction to message ids.
[SCSI] qla2xxx: Correctly print out/in mailbox registers.
[SCSI] qla2xxx: Add a new interface to update versions.
[SCSI] qla2xxx: Move queue depth ramp down message to i/o debug level.
[SCSI] qla2xxx: Select link initialization option bits from current operating mode.
[SCSI] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support.
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN
[SCSI] qla2xxx: Correct Interrupt Register offset for ISPFX00
[SCSI] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen().
[SCSI] qla2xxx: Send all AENs for ISPFx00 to above layers.
[SCSI] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS
...
|
|
While we are likley to succeed and break out of this loop, it isn't
guaranteed. We should be power and thread friendly if we do have to
go around for a second (or third, or more) attempt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues,
removing the 3-4 different locks that were taken for every character.
This code has been beaten on for a long time in linux-next with no
reported regressions.
Other than that, a range of serial and tty driver updates and
revisions. Full details in the shortlog"
* tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (226 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
serial: imx: initialize the local variable
tty: ar933x_uart: add device tree support and binding documentation
tty: ar933x_uart: allow to build the driver as a module
ARM: dts: msm: Update uartdm compatible strings
devicetree: serial: Document msm_serial bindings
serial: unify serial bindings into a single dir
serial: fsl-imx-uart: Cleanup duplicate device tree binding
tty: ar933x_uart: use config_enabled() macro to clean up ifdefs
tty: ar933x_uart: remove superfluous assignment of ar933x_uart_driver.nr
tty: ar933x_uart: use the clk API to get the uart clock
tty: serial: cpm_uart: Adding proper request of GPIO used by cpm_uart driver
serial: sirf: fix the amount of serial ports
serial: sirf: define macro for some magic numbers of USP
serial: icom: move array overflow checks earlier
TTY: amiserial, remove unnecessary platform_set_drvdata()
serial: st-asc: remove unnecessary platform_set_drvdata()
msm_serial: Send more than 1 character on the console w/ UARTDM
msm_serial: Add support for non-GSBI UARTDM devices
msm_serial: Switch clock consumer strings and simplify code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree merge from Greg KH:
"Here's the bit staging tree pull request for 3.12-rc1.
Lots of staging driver updates, and fixes. Lustre is finally enabled
in the build, and lots of cleanup started happening in it. There's a
new wireless driver in here, and 2 new TTY drivers, which cause the
overall lines added/removed to be quite large on the "added" side.
The IIO driver updates are also coming through here, as they are tied
to the staging iio drivers"
* tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (942 commits)
staging: dwc2: make dwc2_core_params documentation more complete
staging: dwc2: validate the value for phy_utmi_width
staging: dwc2: interpret all hwcfg and related register at init time
staging: dwc2: properly mask the GRXFSIZ register
staging: dwc2: remove redundant register reads
staging: dwc2: re-use hptxfsiz variable
staging: dwc2: simplify debug output in dwc_hc_init
staging: dwc2: add missing shift
staging: dwc2: simplify register shift expressions
staging: dwc2: only read the snpsid register once
staging: dwc2: unshift non-bool register value constants
staging: dwc2: fix off-by-one in check for max_packet_count parameter
staging: dwc2: remove specific fifo size constants
Staging:BCM:DDRInit.c:Renaming __FUNCTION__
staging: bcm: remove Version.h file.
staging: rtl8188eu: off by one in rtw_set_802_11_add_wep()
staging: r8188eu: copying one byte too much
staging: rtl8188eu: || vs && typo
staging: r8188eu: off by one bugs
staging: crystalhd: Resolve sparse 'different base types' warnings.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull first batch of s390 updates from Martin Schwidefsky:
"The most interesting change is that Martin converted s390 to generic
hardirqs. Which means that all current architectures have been
converted and that CONFIG_GENERIC_HARDIRQS can be removed. Martin
prepared a patch for that already (see genirq branch), but the best
time to merge that is probably at the end of the merge window / begin
of -rc1.
Another patch converts s390 to software referenced bits instead of
relying on the reference bit in the storage key. Therefore s390
doesn't use storage keys anymore, except for kvm.
Besides that we have improvements, cleanups and fixes in PCI, DASD and
all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (32 commits)
s390/pci: use virtual memory for iommu bitmap
s390/cio: fix unlocked access of global bitmap
s390/pci: update function handle after resume from hibernate
s390/pci: try harder to modify a function
s390/pci: split lpf
s390/hibernate: add early resume function
s390/pci: add recover sysfs knob
s390/pci: use claim_resource
s390/pci/hotplug: convert to be builtin only
s390/mm: implement software referenced bits
s390/dasd: fix statistics for recovered requests
s390/tx: allow program interruption filtering in user space
s390/pgtable: fix mprotect for single-threaded KVM guests
s390/time: return with irqs disabled from psw_idle
s390/kprobes: add support for compare and branch instructions
s390/switch_to: fix save_access_regs() / restore_access_regs()
s390/bitops: fix inline assembly constraints
s390/dasd: enable raw_track_access reads without direct I/O
s390/mm: introduce ptep_flush_lazy helper
s390/time: clock comparator revalidation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Kill harmless warning messages when running a multi-platform kernel
on Atari
- Correct virt/phys mixups that didn't actually hurt due to identity
mappings"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: ARAnyM - Always use physical addresses in NatFeat calls
m68k: Ignore disabled HSYNC interrupt on Atari for irqs_disabled()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for HTU21D (humidity sensor)
- add support for Fam16h (Kabini) to k10temp
- add support for NCT6102D/6106D and NCT6791D to nct6775 driver
- add support for ADS1115 to ads1015 driver
- add support for hibernate to w83627ehf and nct6775 drivers
- some minor cleanups
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (htu21) Add Measurement Specialties HTU21D support
hwmon: Change my email address.
hwmon: (k10temp) Add support for Fam16h (Kabini)
hwmon: (adt7462) ADT7462_REG_VOLT_MAX() should return 0
hwmon: (ads1015) Add support for ADS1115
hwmon: (w83627ehf) Add support for hibernate
hwmon: (nct6775) Add support for hibernate
hwmon: use dev_get_platdata()
hwmon: (nct6775) Fix size of data->temp array
hwmon: (nct6775) Avoid using device platform data outside probe function
hwmon: (nct6775) Add support for NCT6791D
hwmon: (nct6775) Add support for beep attributes
hwmon: (nct6775) Add support for critical low/high temperature limits on NCT6106
hwmon: (nct6775) Add support for NCT6102D/6106D
hwmon: (nct6775) Support two SuperIO chips in the same system
hwmon: (nct6775) Allocate attributes dynamically from templates
hwmon: (coretemp) Atom CPUs don't support TjMax; no warning needed
|
|
The check if the queue is full and adding current to the wait queue of
pending msgsnd() operations (ss_add()) must be atomic.
Otherwise:
- the thread that performs msgsnd() finds a full queue and decides to
sleep.
- the thread that performs msgrcv() first reads all messages from the
queue and then sleeps, because the queue is empty.
- the msgrcv() calls do not perform any wakeups, because the msgsnd()
task has not yet called ss_add().
- then the msgsnd()-thread first calls ss_add() and then sleeps.
Net result: msgsnd() and msgrcv() both sleep forever.
Observed with msgctl08 from ltp with a preemptible kernel.
Fix: Call ipc_lock_object() before performing the check.
The patch also moves security_msg_queue_msgsnd() under ipc_lock_object:
- msgctl(IPC_SET) explicitely mentions that it tries to expunge any
pending operations that are not allowed anymore with the new
permissions. If security_msg_queue_msgsnd() is called without locks,
then there might be races.
- it makes the patch much simpler.
Reported-and-tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: stable@vger.kernel.org # for 3.11
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Not much exciting going on with the regulator API this time around,
lots of driver fixes and enhancements - the main thing is the addition
of a new API to help make the stubbing code do the right thing for
missing regulator mappings.
Highlights:
- A new regulator_get_optional() API call for regulators that can be
absent in normal operation. This currently does nothing but will
be used to improve the stubbing code for unspecified regulators,
helping avoid some of the issues we've seen with adding new
regulator support.
- Helpers for devices with multiple linear ranges of voltages in the
same regulator.
- Moved the helpers into a separate file since core.c is getting
rather large.
- New drivers for Dialog DA9210 and DA9063, Freescale pfuze100 and
Marvell 88pm800"
* tag 'regulator-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (70 commits)
regulator: da9063: Statize da9063_ldo_lim_event
regulator: lp872x: Make REGULATOR_LP872X depend on I2C rather than I2C=y
regulator: tps65217: Convert to use linear ranges
regulator: da9063: Use IS_ERR to check return value of regulator_register()
regulator: da9063: Optimize da9063_set_current_limit implementation
regulator: build: Allow most regulators to be built as modules
regulator: Add devm_regulator_get_exclusive()
regulator: da9063: Add Dialog DA9063 voltage regulators support.
regulator: ti-abb: simplify platform_get_resource_byname/devm_ioremap_resource
hwmon: (sht15) Use devm_regulator_get_optional()
regulator: core: Use bool for exclusivitity flag
regulator: 88pm800: forever loop in pm800_regulator_probe()
cpufreq: cpufreq-cpu0: Use devm_regulator_get_optional()
regulator: da9210: Remove redundant MODULE_ALIAS
regulator: 88pm800: Fix checking whether num_regulator is valid
regulator: s2mps11: Fix setting ramp_delay
regulator: s2mps11: Fix wrong arguments for regmap_update_bits() call
regulator: palmas: Update the DT binding doc for smps10 out1 and out2
regulator: palmas: model SMPS10 as two regulators
regulator: core: Move list_voltage_{linear,linear_range,table} to helpers.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Business as usual for SPI - some new drivers, lots of fixes and
updates to existing drivers plus some new framework features. Notable
changes are:
- Support for dual and quad data lines, commonly used by flash chips
to improve performance, from Wang Yuhang.
- Factored out a common pattern for runtime PM implementation into
the core saving a bunch of code.
- A particularly nice set of updates to the ep93xx driver from
H Hartley Sweeten, modernising it and reducing the code size a lot.
- New drivers for Blackfin v3, EFM32, Freescale DSPI and TI QSPI"
* tag 'spi-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (133 commits)
spi/qspi: fix missing unlock on error in ti_qspi_start_transfer_one()
spi: quad: fix the name of DT property
spi: core: Fix spi_register_master error handling
spi: efm32: Fix build error
spi: altera: Use DIV_ROUND_UP to calculate hw->bytes_per_word
spi: rspi: Add spi_master_get() call to prevent use after free
spi: quad: Make DT properties optional
spi: quad: Fix missing return
spi: Use dev_get_drvdata at appropriate places
spi: use dev_get_platdata()
spi: nuc900: Fix mode_bits setting
spi: simplify devm_request_mem_region/devm_ioremap
spi: altera: Simplify altera_spi_txrx implementation for noirq case
spi: spi-rspi: fix inconsistent spin_lock_irqsave
spi/qspi: Add compatible string for am4372.
spi/qspi: Fix device table entry
spi/sirf: fix the misunderstanding about len of spi_transfer
spi/qspi: Add dual/quad spi read support
spi: sirf: fix error return code in spi_sirfsoc_probe()
spi: bcm2835: Add spi_master_get() call to prevent use after free
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq"
* tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Make cache_present bitmap per node
regmap: rbtree: Reduce number of nodes, take 2
regmap: rbtree: Simplify adjacent node look-up
regmap: debugfs: Fix continued read from registers file
regcache-rbtree: Fix reg_stride != 1
regmap: Allow multiple patches to be registered
regmap: regcache: allow read-only regs to be cached
regmap: fix regcache_reg_present() for empty cache
regmap: core: allow a virtual range to cover its own data window
regmap: irq: document mask/wake_invert flags
regmap: irq: make flags bool and put them in a bitfield
regmap: irq: Allow to acknowledge masked interrupts during initialization
regmap: Provide __acquires/__releases annotations
|
|
Merge lockref infrastructure code by me and Waiman Long.
I already merged some of the preparatory patches that didn't actually do
any semantic changes earlier, but this merges the actual _reason_ for
those preparatory patches.
The "lockref" structure is a combination "spinlock and reference count"
that allows optimized reference count accesses. In particular, it
guarantees that the reference count will be updated AS IF the spinlock
was held, but using atomic accesses that cover both the reference count
and the spinlock words, we can often do the update without actually
having to take the lock.
This allows us to avoid the nastiest cases of spinlock contention on
large machines under heavy pathname lookup loads. When updating the
dentry reference counts on a large system, we'll still end up with the
cache line bouncing around, but that's much less noticeable than
actually having to spin waiting for the lock.
* lockref:
lockref: implement lockless reference count updates using cmpxchg()
lockref: uninline lockref helper functions
vfs: reimplement d_rcu_to_refcount() using lockref_get_or_lock()
vfs: use lockref_get_not_zero() for optimistic lockless dget_parent()
lockref: add 'lockref_get_or_lock() helper
|
|
The endianness attribute on the 'aux' local variable is wrong, and can
lead to wrong endianness on big-endian machines,
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Push file descriptor list locking down to per-device locking. Let sg_index_lock
only protect device lookup.
sdp->detached is also set and checked with this lock held.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
@detached is set under the protection of sg_index_lock. Without getting the
lock, new sfp will be added during sg removal and there is no chance for it
to be picked out. So check with sg_index_lock held in sg_add_sfp().
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Open exclusive check is protected by o_sem, no need sg_open_exclusive_lock.
@exclude is used to record which type of rwsem we are holding.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
A race condition may happen if two threads are both trying to open the same sg
with O_EXCL simultaneously. It's possible that they both find fsds list is
empty and get_exclude(sdp) returns 0, then they both call set_exclude() and
break out from wait_event_interruptible and resume open.
Now use rwsem to protect this process. Exclusive open gets write lock and
others get read lock. The lock will be held until file descriptor is closed.
This also leads 'exclude' only a status rather than a check mark.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
unmap_alignment != 0
Commit b90ebc3d5c41c9164ae04efd2e4f8204c2a186f1 ("[SCSI] scsi_debug:
fix logical block provisioning support") fixed several issues with
logical block provisioning support, but it still doesn't properly fix
the cases when unmap_alignment > 0.
For example, load scsi_debug module with the following module parameters
and make all blocks mapped by filling the storage with zero.
# modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4
# dd if=/dev/zero of=$DEV
Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS
unexpectedly reports that the last UNMAP has done nothing.
# sg_unmap --lba=1 --num=4 $DEV
# sg_get_lba_status --lba=1 $DEV
descriptor LBA: 0x0000000000000001 blocks: 16383 mapped
The problem is in map_index_to_lba(), which should return the first
LBA which is corresponding to a given index of provisioning map
(map_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
With module parameter num_parts > 0, partition table is built on the
ramdisk storage when loading the driver. Unfortunately, there is an
endianness bug in sdebug_build_parts(). So the partition table is not
correctly initialized on big-endian systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
