| Age | Commit message (Collapse) | Author |
|---|
|
The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a redundant semicolon, this patch removes it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause parameters include source address, transmit gap and pause time.
The default value of the pause source address is zero in the hardware.
Default pause parameters need to be set to the hardware. Also, when
setting new mac address, the pause source address need to be updated.
Fixes: 9dc2145d910e ("net: hns3: Add support for PFC setting in TM module")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When initializing the MAC, the MTU vlaue need to be set to the hardware
too. Otherwise, the MTU value of software will be different from the MTU
value of hardware.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when changing MTU, The new MTU must need to be set to netdevice.
Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.
This patch fixes the bug setting a error max frame size to hardware.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a9c782822166 ("net: hns3: add support for set_pauseparam")
adds set_pauseparam support for ethtool cmd, but forgets to update
fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam().
The wrong fc_mode_last_time will be used to update flow control mode
when lldpad has been running. As a result, when using the ethtool
command "-a", user will get a wrong pause parameter.
This patch adds the fc_mode_last_time update when PFC mode is disabled.
Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The result of tqp statistics query was read with an
error position, fix it according to the user manual.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add packet statistics of netdev for ethtool -S, in
order to show the statistics data for current net
device.
Remove update_stats() calling because it has been
completed in hns3_get_netdev_stats().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The member "stats_size" of struct hns3_stats is useless,
remove it and fix the macro definition which has uses this
struct.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The member "stats_offset" was designed to indicate the offset
of each member of struct ring_stats in struct hns3_enet_ring,
but forgot to add the offset of the member in struct ring_stats.
Fixes: 496d03e960a ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An error loop index was used while querying statistics data
of tqps, which may cause call trace.
Fixes: 496d03e960ae ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dropped tx/rx packets number of each tqp should also
be counted into the total drop tx/rx packets numbers.
Fixes: 76ad4f0ee74 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the HNS3_NIC_STATE_DOWN bit when NIC state changes.
When NIC is down, mask the packet statistics for querying
with ifconfig command. It's a common practice.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It takes more than 200 query response messages between
driver and IMP, while updating the packet statistics.
It's too heavy for IMP to update it per second.
Extend the update period of packet statistics data from
1 second to 300 seconds(if too long, the statistics may
overflow).
As a result, we need to update it while querying with
ifconfig tool to keep the statistics data fresh.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The igu_rx_err_pkt indicates the same error with
mac_rx_fcs_err_pkt_num, so remove it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix spelling error "overrsize" --> "oversize".
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rxvlan offload status can only be changed by PF. Initialize
the value of NETIF_F_HW_VLAN_CTAG_RX bit of hw_features for
VFS to false, make sure user can't be able to change it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds vlan filter enable switch to
support ethtool -K ethX rx-vlan-filter on/off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subash Abhinov Kasiviswanathan says:
====================
net: qualcomm: rmnet: Enable csum offloads
This series introduces the MAPv4 packet format for checksum
offload plus some other minor changes.
Patches 1-3 are cleanups.
Patch 4 renames the ingress format to data format so that all data
formats can be configured using this going forward.
Patch 5 uses the pacing helper to improve TCP transmit performance.
Patch 6-9 defines the the MAPv4 for checksum offload for RX and TX.
A new header and trailer format are used as part of MAPv4.
For RX checksum offload, only the 1's complement of the IP payload
portion is computed by hardware. The meta data from RX header is
used to verify the checksum field in the packet. Note that the
IP packet and its field itself is not modified by hardware.
This gives metadata to help with the RX checksum. For TX, the
required metadata is filled up so hardware can compute the
checksum.
Patch 10 enables GSO on rmnet devices
v1->v2: Fix sparse errors reported by kbuild test robot
v2->v3: Update the commit message for Patch 5 based on Eric's comments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Real devices may support scatter gather(SG), so enable SG on rmnet
devices to use GSO. GSO reduces CPU cycles by 20% for a rate of
146Mpbs for a single stream TCP connection.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX checksum offload applies to TCP / UDP packets which are not
fragmented using the MAPv4 checksum trailer. The following needs to be
done to have checksum computed in hardware -
1. Set the checksum start offset and inset offset.
2. Set the csum_enabled bit
3. Compute and set 1's complement of partial checksum field in
transport header.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.
rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -
1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
value from step 3.
5. Compares the value from step 4 to the checksum value from the
TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
and the packet is passed on to network stack. If there is a
failure, then the packet is passed on as such without modifying
the ip_summed field.
The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.
If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAPv4 packet format adds support for RX / TX checksum offload.
For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly
10% CPU cycles are saved.
For receive path, there is a checksum trailer appended to the end of
the MAP packet. The valid field indicates if hardware has computed
the checksum. csum_start_offset indicates the offset from the start
of the IP header from which hardware has computed checksum.
csum_length is the number of bytes over which the checksum was
computed and the resulting value is csum_value.
In the transmit path, a header is appended between the end of the MAP
header and the start of the IP packet. csum_start_offset is the offset
in bytes from which hardware will compute the checksum if the
csum_enabled bit is set. udp_ip4_ind indicates if the checksum
value of 0 is valid or not. csum_insert_offset is the offset from the
csum_start_offset where hardware will insert the computed checksum.
The use of this additional packet format for checksum offload is
explained in subsequent patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The real device over which the rmnet devices are installed also
aggregate multiple IP packets and sends them as a single large
aggregate frame to the hardware. This causes degraded throughput
for TCP TX due to bufferbloat.
To overcome this problem, pacing shift value of 8 is set using the
sk_pacing_shift_update() helper. This value was determined based
on experiments with a single stream TCP TX using iperf for a
duration of 30s.
Pacing shift | Observed data rate (Mbps)
10 | 9
9 | 140
8 | 146 (Max link rate)
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is done so that we can use this field for both ingress and
egress flags.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet_map_demultiplex() is only declared but not defined anywhere,
so remove it.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rmnet devices cannot have a mux id of 255. This is validated when
assigning the mux id to the rmnet devices. As a result, checking for
mux id 255 does not apply in egress path.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already check the headroom once in rmnet_map_egress_handler(),
so this is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
ipv6: Align nexthop behaviour with IPv4
This set tries to eliminate some differences between IPv4's and IPv6's
treatment of nexthops. These differences are most likely a side effect
of IPv6's data structures (specifically 'rt6_info') that incorporate
both the route and the nexthop and the late addition of ECMP support in
commit 51ebd3181572 ("ipv6: add support of equal cost multipath
(ECMP)").
IPv4 and IPv6 do not react the same to certain netdev events. For
example, upon carrier change affected IPv4 nexthops are marked using the
RTNH_F_LINKDOWN flag and the nexthop group is rebalanced accordingly.
IPv6 on the other hand, does nothing which forces us to perform a
carrier check during route lookup and dump. This makes it difficult to
introduce features such as non-equal-cost multipath that are built on
top of this set [1].
In addition, when a netdev is put administratively down IPv4 nexthops
are marked using the RTNH_F_DEAD flag, whereas IPv6 simply flushes all
the routes using these nexthops. To be consistent with IPv4, multipath
routes should only be flushed when all nexthops in the group are
considered dead.
The first 12 patches introduce non-functional changes that store the
RTNH_F_DEAD and RTNH_F_LINKDOWN flags in IPv6 routes based on netdev
events, in a similar fashion to IPv4. This allows us to remove the
carrier check performed during route lookup and dump.
The next three patches make sure we only flush a multipath route when
all of its nexthops are dead.
Last three patches add test cases for IPv4/IPv6 FIB. These verify that
both address families react similarly to netdev events.
Finally, this series also serves as a good first step towards David
Ahern's goal of treating nexthops as standalone objects [2], as it makes
the code more in line with IPv4 where the nexthop and the nexthop group
are separate objects from the route itself.
1. https://github.com/idosch/linux/tree/ipv6-nexthops
2. http://vger.kernel.org/netconf2017_files/nexthop-objects.pdf
Changes since RFC (feedback from David Ahern):
* Remove redundant declaration of rt6_ifdown() in patch 4 and adjust
comment referencing it accordingly
* Drop patch to flush multipath routes upon NETDEV_UNREGISTER. Reword
cover letter accordingly
* Use a temporary variable to make code more readable in patch 15
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check that IPv4 and IPv6 react the same when the carrier of a netdev is
toggled. Local routes should not be affected by this, whereas unicast
routes should.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check that IPv4 and IPv6 react the same when a netdev is being put
administratively down.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test cases to check that IPv4 and IPv6 react to a netdev being
unregistered as expected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, IPv6 deletes nexthops from a multipath route when the
nexthop device is put administratively down. This differs from IPv4
where the nexthops are kept, but marked with the RTNH_F_DEAD flag. A
multipath route is flushed when all of its nexthops become dead.
Align IPv6 with IPv4 and have it conform to the same guidelines.
In case the multipath route needs to be flushed, its siblings are
flushed one by one. Otherwise, the nexthops are marked with the
appropriate flags and the tree walker is instructed to skip all the
siblings.
As explained in previous patches, care is taken to update the sernum of
the affected tree nodes, so as to prevent the use of wrong dst entries.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch is going to allow dead routes to remain in the FIB tree
in certain situations.
When this happens we need to be sure to bump the sernum of the nodes
where these are stored so that potential copies cached in sockets are
invalidated.
The function that performs this update assumes the table lock is not
taken when it is invoked, but that will not be the case when it is
invoked by the tree walker.
Have the function assume the lock is taken and make the single caller
take the lock itself.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to allow dead routes to stay in the FIB tree (e.g., when
they are part of a multipath route, directly connected route with no
carrier) and revive them when their nexthop device gains carrier or when
it is put administratively up.
This is equivalent to the addition of the route to the FIB tree and we
should therefore take care of updating the sernum of all the parent
nodes of the node where the route is stored. Otherwise, we risk sockets
caching and using sub-optimal dst entries.
Export the function that performs the above, so that it could be invoked
from fib6_ifup() later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in previous patch, fib6_ifdown() needs to consider the
state of all the sibling routes when a multipath route is traversed.
This is done by evaluating all the siblings when the first sibling in a
multipath route is traversed. If the multipath route does not need to be
flushed (e.g., not all siblings are dead), then we should just skip the
multipath route as our work is done.
Have the tree walker jump to the last sibling when it is determined that
the multipath route needs to be skipped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When routes that are a part of a multipath route are evaluated by
fib6_ifdown() in response to NETDEV_DOWN and NETDEV_UNREGISTER events
the state of their sibling routes is not considered.
This will change in subsequent patches in order to align IPv6 with
IPv4's behavior. For example, when the last sibling in a multipath route
becomes dead, the entire multipath route needs to be removed.
To prevent the tree walker from re-evaluating all the sibling routes
each time, we can simply evaluate them once - when the first sibling is
traversed.
If we determine the entire multipath route needs to be removed, then the
'should_flush' bit is set in all the siblings, which will cause the
walker to flush them when it traverses them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the RTNH_F_DEAD flag was only reported in route dump when
the 'ignore_routes_with_linkdown' sysctl was set. This is expected as
dead routes were flushed otherwise.
The reliance on this sysctl is going to be removed, so we need to report
the flag regardless of the sysctl's value.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, dead routes are only present in the routing tables in case
the 'ignore_routes_with_linkdown' sysctl is set. Otherwise, they are
flushed.
Subsequent patches are going to remove the reliance on this sysctl and
make IPv6 more consistent with IPv4.
Before this is done, we need to make sure dead routes are skipped during
route lookup, so as to not cause packet loss.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to previous patch, there is no need to check for the carrier of
the nexthop device when dumping the route and we can instead check for
the presence of the RTNH_F_LINKDOWN flag.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the RTNH_F_LINKDOWN flag is set in nexthops, we can avoid the
need to dereference the nexthop device and check its carrier and instead
check for the presence of the flag.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is valid to install routes with a nexthop device that does not have a
carrier, so we need to make sure they're marked accordingly.
As explained in the previous patch, host and anycast routes are never
marked with the 'linkdown' flag.
Note that reject routes are unaffected, as these use the loopback device
which always has a carrier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to IPv4, when the carrier of a netdev changes we should toggle
the 'linkdown' flag on all the nexthops using it as their nexthop
device.
This will later allow us to test for the presence of this flag during
route lookup and dump.
Up until commit 4832c30d5458 ("net: ipv6: put host and anycast routes on
device with address") host and anycast routes used the loopback netdev
as their nexthop device and thus were not marked with the 'linkdown'
flag. The patch preserves this behavior and allows one to ping the local
address even when the nexthop device does not have a carrier and the
'ignore_routes_with_linkdown' sysctl is set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make IPv6 more in line with IPv4 we need to be able to respond
differently to different netdev events. For example, when a netdev is
unregistered all the routes using it as their nexthop device should be
flushed, whereas when the netdev's carrier changes only the 'linkdown'
flag should be toggled.
Currently, this is not possible, as the function that traverses the
routing tables is not aware of the triggering event.
Propagate the triggering event down, so that it could be used in later
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patch marked nexthops with the 'dead' and 'linkdown' flags.
Clear these flags when the netdev comes back up.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a netdev is put administratively down or unregistered all the
nexthops using it as their nexthop device should be marked with the
'dead' and 'linkdown' flags.
Currently, when a route is dumped its nexthop device is tested and the
flags are set accordingly. A similar check is performed during route
lookup.
Instead, we can simply mark the nexthops based on netdev events and
avoid checking the netdev's state during route dump and lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By the time fib6_net_exit() is executed all the netdevs in the namespace
have been either unregistered or pushed back to the default namespace.
That is because pernet subsys operations are always ordered before
pernet device operations and therefore invoked after them during
namespace dismantle.
Thus, all the routing tables in the namespace are empty by the time
fib6_net_exit() is invoked and the call to rt6_ifdown() can be removed.
This allows us to simplify the condition in fib6_ifdown() as it's only
ever called with an actual netdev.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
