aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-02-23ath9k_htc: Remove OP_PROTECT_ENABLESujith Manoharan
CTS protection can be obtained from mac80211 directly. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Remove OP_PREAMBLE_SHORTSujith Manoharan
mac80211's BSS info can be used for this. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Fix error handling in add_interfaceSujith Manoharan
Addition of a station might fail - handle this error properly by removing the VAP on the target. Also, bail out immediately if the max. no of interfaces has been reached. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Unify target capability updatingSujith Manoharan
Update capabilites on the target once, when start() is called, there is no need for redundant updating on adding an interface. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Allow upto two simultaneous interfacesSujith Manoharan
Multiple interfaces can be configured if a slot is free on the target. Monitor mode also requires a slot. The maximum number of stations that can be handled in the firmware is 8, manage the station slots accordingly. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Handle storage devicesSujith Manoharan
Some AR7010 based devices are recognized as storage media. Sending a CD-EJECT command to the device will 'convert' it into a WLAN device. Do this within the driver itself, removing the dependancy on an external program (usb_modeswitch). Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23mwl8k: Invert tx queues for set_hw_spec and set_edca_paramsNishant Sarmukadam
mac80211 and mwl8k FW tx queue priorities map inversely to each other. Fix this. Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Tested-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23mwl8k: Tell mac80211 we have rate adaptation in FWNishant Sarmukadam
All mwl8k parts perform rate control in firmware. Make this known to mac80211 so that it does not launch minstrel. Also, because actual tx rate information is not available from the firmware, invalidate the rate status before returning the skb to mac80211. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23mwl8k: fix rf_antenna rx argument for APNishant Sarmukadam
When configuring rx antennas using CMD_RF_ANTENNA, the argument input is the number of antennas to be enabled. For AP, we support 3 rx antennas and hence set the field to 3. For tx antennas, value is a bitmap, so 0x7 enables all three. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23Merge branch 'for-linville' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx
2011-02-23Merge branch 'wireless-next-2.6' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
2011-02-23wl12xx: AP-mode - management of links in PS-modeArik Nemtsov
Update the PS mode of each link according to a bitmap polled from fw_status. Manually notify mac80211 about PS mode changes in connected stations. mac80211 will only be notified about PS start when the station is in PS and there is a small number of TX blocks from this link ready in HW. This is required for waking up the remote station since the TIM is updated entirely by FW. When a station enters mac80211-PS-mode, we drop all the skbs in the low-level TX queues belonging to this sta with STAT_TX_FILTERED to keep our queues clean. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: AP-mode - count free FW TX blocks per linkArik Nemtsov
Count the number of FW TX blocks allocated per link. We add blocks to a link counter when allocated for a TX descriptor. We remove blocks according to counters in fw_status indicating the number of freed blocks in FW. These counters are polled after each IRQ. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: AP mode - fix bug in cleanup of wl1271_op_sta_add()Arik Nemtsov
Remove an active hlid when chip wakeup fails. In addition rename the involved functions. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: AP-mode - support HW based link PS monitoringArik Nemtsov
When operating in AP mode the wl1271 hardware filters out null-data packets as well as management packets. This makes it impossible for mac80211 to monitor the PS mode by using the PM bit of incoming frames. Disable mac80211 automatic link PS-mode handling by supporting IEEE80211_HW_AP_LINK_PS in HW flags. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: report invalid TX rate when returning non-TX-ed skbsArik Nemtsov
Report a TX rate idx of -1 and count 0 when returning untransmitted skbs to mac80211 using ieee80211_tx_status(). Otherwise mac80211 tries to use the returned (essentially garbage) status. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: AP-mode - TX queue per link in ACArik Nemtsov
When operating in AP-mode we require a per link tx-queue. This allows us to implement HW assisted PS mode for links, as well as regulate per-link FW TX blocks consumption. Split each link into ACs to support future QoS for AP-mode. AC queues are emptied in priority and per-link queues are scheduled in a simple round-robin fashion. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: AP-mode - fix race condition on sta connectionArik Nemtsov
If a sta starts transmitting immediately after authentication, sometimes the FW deauthenticates it. Fix this by marking the sta "in-connection" in FW before sending the autentication response. The "in-connection" entry is automatically removed when connection succeeds or after a timeout. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: fix potential race condition with TX queue watermarkArik Nemtsov
Check the conditions for the high/low TX queue watermarks when the spin-lock is taken. This prevents race conditions as tx_queue_count and the flag checked are only modified when the spin-lock is taken. The following race was in mind: - Queues are almost full and wl1271_op_tx() will stop the queues, but it doesn't get the spin-lock yet. - (on another CPU) tx_work_locked() dequeues 15 skbs from this queue and tx_queue_count is updated to reflect this - wl1271_op_tx() does not check tx_queue_count after taking the spin-lock and incorrectly stops the queue. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: always set mac_address when configuring ht capsEliad Peller
The mac_address should be set also when ht caps are disabled. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-23wl12xx: use standard ALIGN() macroEliad Peller
Use the standard ALIGN() macro instead of redefining similar macros. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: declare support for IEEE80211_HW_REPORTS_TX_ACK_STATUSEliad Peller
The wl12xx fw supports ack status reporting for tx frames, so add the IEEE80211_HW_REPORTS_TX_ACK_STATUS flag to our supported features. Since we do the rate control in the fw, we'll probably want to adjust the STA_LOST_PKT_THRESHOLD heuristics in the future, to account for retransmissions as well. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: fix MODULE_AUTHOR email addressLuciano Coelho
Change my old email address to the new one in MODULE_AUTHOR. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: avoid blocking while holding rcu lock on bss info changeArik Nemtsov
Some blocking functions were called while holding the rcu lock for accessing STA information. This can lead to a deadlock. Save the required info beforehand and release the rcu without blocking. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: fix identification of beacon packets (debug)Eliad Peller
for debugging purposes, wl12xx determines whether a rx packet is a beacon packet. however, it checks only the frame_control subtype without checking the actual packet type, which leads to false identification in some cases. use ieee80211_is_beacon instead. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: update PLT initialization for new firmwareGery Kahn
In revision > 6.1.3.0.0 the firmware expects memory configuration command as part of boot. This was missing if driver boots in PLT mode. The patch adds the memory configuration command, which fixes PLT commands tx continuous and rx statistics. Signed-off-by: Gery Kahn <geryk@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-22wl12xx: change type from u8 to intDan Carpenter
ret is used to store int types. Using an u8 will break the error handling. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-21ath9k_hw: Fix power on resetSujith Manoharan
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET" added an extra udelay to the reset routine. As the required delay is already present, remove this. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Add support for RT5390 chipRA-Shiang Tu
Add new RT5390 chip support Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Add/Modify the GPIO register definitionShiang Tu
Revise/Add GPIO register related definitions Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Add/Modify protection related register definitionsShiang Tu
Make the definition of protection related registers more precisely Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Remove superfluos empty lineHelmut Schaa
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21Revert "rt2x00 : avoid timestamp for monitor injected frame."Helmut Schaa
This reverts commit e81e0aef32bfa7f593b14479b9c7eaa7196798ac "rt2x00 : avoid timestamp for monitor injected frame." as it breaks proper timestamp insertion into probe responses injected by hostapd for example. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Benoit PAPILLAULT <benoit.papillault@free.fr> Cc: Alban Browaeys <prahal@yahoo.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Minor optimization for devices with RTS/CTS offloadHelmut Schaa
Only devices that don't have RTS/CTS offload need to check for IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT. By swapping both conditions we keep the same number of needed conditionals for devices without RTS/CTS offload but save one conditional on devices with RTS/CTS offload. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Fix rt2800 txpower setting to correct valueRA-Jay Hung
TX_PWR_CFG_* setting need to consider below cases -compesate 20M/40M tx power delta for 2.4/5GHZ band -limit maximum EIRP tx power to power_level of regulatory requirement Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna ↵RA-Jay Hung
diversity support For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select default antenna using gpio control way even if we do not turn on antenna diversity feature. Seperate the meaning of TX/RX chain and antenna. Some chips use 2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain but may have 2 RX antennas to do antenna diversity. Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Remove obsolete/unused macrosLarry Finger
The original code has many macros that are no longer needed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192ce: Fix endian warningsLarry Finger
Drivers rtlwifi, and rtl8192ce generate a large number of sparse warnings. This patch fixes most of them. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Modify build system for rtl8192cuLarry Finger
Modify Kconfig and Makefile to build rtl8192cu. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine trxGeorge
Add routine rtlwifi/rtl8192cu/trx.c. This routine differs from the rtl8192ce file of the same name. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine tableGeorge
Add rtlwifi/rtl8192cu/table.c. These tables are different than the ones used in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine rfGeorge
Add rtlwifi/rtl8192cu/rf.c. This routine is distinct from the one in rtl8192ce with the same name. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine phyGeorge
Add the routine rtlwifi/rtl8192cu/phy.c. Most of the code is included from rtlwifi/rtl8192c/phy_common.c. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine macGeorge
Add the routine rtlwifi/rtl8192cu/hw.c. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routine hwGeorge
Add the routine rtlwifi/rtl8192cu/hw.c. This one is distinct from the routine of the same name in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: rtl8192cu: Add routines dm, fw, led and swGeorge
Add the rtlwifi/rtl8192cu routines for dm.c, fw.c, led.c and sw.c. Where possible, these routines use the corresponding code in rtl8192ce. Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Move common parts of rtl8192ce/phy.cLarry Finger
Move common routines from rtlwifi/rtl8192ce/phy.c and .../rtl8192cu/phy.c into rtlwifi/rtl8192c/phy_common.c. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Modify wifi.h for rtl8192cuLarry Finger
Further merge of parameters needed for rtl8192cu. In addition, some changes needed for rtl8192se and rtl8192de are included and additional Hungarian notation is removed. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Add headers for rtl8187cuGeorge
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: George <george0505@realtek.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-21rtlwifi: Modify some rtl8192ce routines for merging rtl8192cuLarry Finger
Modify some rtl8192ce routines for merging with rtl8192cu. In addition, remove some usage of Hungarian notation. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 09:53:08 +0000