Age | Commit message (Collapse) | Author |
|
This reverts commit 16b5f5ce351f8709a6b518cc3cbf240c378305bf
where it restructures do_reset. There are patches being tested that
would require major rework if this is committed first.
We will resend this after the other patches have been applied.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20201106191745.1679846-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ido Schimmel says:
====================
nexthop: Add support for nexthop objects offload
This patch set adds support for nexthop objects offload with a dummy
implementation over netdevsim. mlxsw support will be added later.
The general idea is very similar to route offload in that notifications
are sent whenever nexthop objects are changed. A listener can veto the
change and the error will be communicated to user space with extack.
To keep listeners as simple as possible, they not only receive
notifications for the nexthop object that is changed, but also for all
the other objects affected by this change. For example, when a single
nexthop is replaced, a replace notification is sent for the single
nexthop, but also for all the nexthop groups this nexthop is member in.
This relieves listeners from the need to track such dependencies.
To simplify things further for listeners, the notification info does not
contain the raw nexthop data structures (e.g., 'struct nexthop'), but
less complex data structures into which the raw data structures are
parsed into.
Tested with a new selftest over netdevsim and with fib_nexthops.sh:
Tests passed: 164
Tests failed: 0
Patch set overview:
Patches #1-#4 introduce the aforementioned data structures and convert
existing listeners (i.e., the VXLAN driver) to use them.
Patches #5-#6 add a new RTNH_F_TRAP flag and the ability to set it and
RTNH_F_OFFLOAD on nexthops. This flag is used by netdevsim for testing
purposes and will also be used by mlxsw. These flags are consistent with
the existing RTM_F_OFFLOAD and RTM_F_TRAP flags.
Patches #7-#14 gradually add the new nexthop notifications.
Patches #15-#18 add a dummy implementation for nexthop offload over
netdevsim and a selftest to exercise both good and bad flows.
Changes since RFC [1]:
Patch #1: s/is_encap/has_encap/
Patch #3: Add a blank line in __nh_notifier_single_info_init()
Patch #5: Reword commit message
Patch #6: s/nexthop_hw_flags_set/nexthop_set_hw_flags/
Patch #7: Reword commit message
Patch #11: Allocate extack on the stack
Follow-up patch sets:
selftests: forwarding: Add nexthop objects tests
mlxsw: Preparations for nexthop objects support - part 1/2
mlxsw: Preparations for nexthop objects support - part 2/2
mlxsw: Add support for nexthop objects
mlxsw: Add support for blackhole nexthops
mlxsw: Update adjacency index more efficiently
[1] https://lore.kernel.org/netdev/20200908091037.2709823-1-idosch@idosch.org/
====================
Link: https://lore.kernel.org/r/20201104133040.1125369-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Test various aspects of the nexthop offload API on top of the netdevsim
implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previous patches added the ability to program nexthop objects.
Therefore, no longer forbid the programming of routes that point to such
objects.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement dummy nexthop "offload" in the driver by storing currently
"programmed" nexthops in a hash table. Each nexthop in the hash table is
marked with "trap" indication and increments the nexthops resource
occupancy.
This will later allow us to test the nexthop offload API on top of
netdevsim.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Spectrum ASIC has a dedicated table where nexthops (i.e., adjacency
entries) are populated. The size of this table can be controlled via
devlink-resource.
Add such a resource to netdevsim so that its occupancy will reflect the
number of nexthop objects currently programmed to the device.
By limiting the size of the resource, error paths could be exercised and
tested.
Example output:
# devlink resource show netdevsim/netdevsim10
netdevsim/netdevsim10:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 4 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 3 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name IPv6 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 1 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 2 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name nexthops size unlimited occ 0 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove in-kernel route notifications when the configuration of their
nexthop changes.
These notifications are unnecessary because the route still uses the
same nexthop ID. A separate notification for the nexthop change itself
is now sent in the nexthop notification chain.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When registering a new notifier to the nexthop notification chain,
replay all the existing nexthops to the new notifier so that it will
have a complete picture of the available nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used by the next patch which extends the function to replay
all the existing nexthops to the notifier block being registered.
Device drivers will be able to pass extack to the function since it is
passed to them upon reload from devlink.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a single nexthop is deleted, the configuration of all the groups
using the nexthop is effectively modified. In this case, emit a
notification in the nexthop notification chain for each modified group
so that listeners would not need to keep track of which nexthops are
member in which groups.
In the rare cases where the notification fails, emit an error to the
kernel log. This is done by allocating extack on the stack and printing
the error logged by the listener that rejected the notification.
Changes since RFC:
* Allocate extack on the stack
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a single nexthop is replaced, the configuration of all the groups
using the nexthop is effectively modified. In this case, emit a
notification in the nexthop notification chain for each modified group
so that listeners would not need to keep track of which nexthops are
member in which groups.
The notification can only be emitted after the new configuration (i.e.,
'struct nh_info') is pointed at by the old shell (i.e., 'struct
nexthop'). Before that the configuration of the nexthop groups is still
the same as before the replacement.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The notification is emitted after all the validation checks were
performed, but before the new configuration (i.e., 'struct nh_info') is
pointed at by the old shell (i.e., 'struct nexthop'). This prevents the
need to perform rollback in case the notification is vetoed.
The next patch will also emit a replace notification for all the nexthop
groups in which the nexthop is used.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Emit a notification in the nexthop notification chain when an existing
nexthop group is replaced.
The notification is emitted after all the validation checks were
performed, but before the new configuration (i.e., 'struct nh_grp') is
pointed at by the old shell (i.e., 'struct nexthop'). This prevents the
need to perform rollback in case the notification is vetoed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Emit a notification in the nexthop notification chain when a new nexthop
is added (not replaced). The nexthop can either be a new group or a
single nexthop.
The notification is sent after the nexthop is inserted into the
red-black tree, as listeners might need to callback into the nexthop
code with the nexthop ID in order to mark the nexthop as offloaded.
A 'REPLACE' notification is emitted instead of 'ADD' as the distinction
between the two is not important for in-kernel listeners. In case the
listener is not familiar with the encoded nexthop ID, it can simply
treat it as a new one. This is also consistent with the route offload
API.
Changes since RFC:
* Reword commit message
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a function that can be called by device drivers to set "offload" or
"trap" indication on nexthops following nexthop notifications.
Changes since RFC:
* s/nexthop_hw_flags_set/nexthop_set_hw_flags/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The flag indicates to user space that the nexthop is not programmed to
forward packets in hardware, but rather to trap them to the CPU. This is
needed, for example, when the MAC of the nexthop neighbour is not
resolved and packets should reach the CPU to trigger neighbour
resolution.
The flag will be used in subsequent patches by netdevsim to test nexthop
objects programming to device drivers and in the future by mlxsw as
well.
Changes since RFC:
* Reword commit message
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the sole listener of the nexthop notification chain (the VXLAN
driver) to the new notification info.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare the new notification information so that it could be passed to
listeners in the new patch.
Changes since RFC:
* Add a blank line in __nh_notifier_single_info_init()
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The next patch will add extack to the notification info. This allows
listeners to veto notifications and communicate the reason to user space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add data structures that will be used for nexthop replace and delete
notifications in the previously introduced nexthop notification chain.
New data structures are added instead of passing the existing nexthop
code structures directly for several reasons.
First, the existing structures encode a lot of bookkeeping information
which is irrelevant for listeners of the notification chain.
Second, the existing structures can be changed without worrying about
introducing regressions in listeners since they are not accessed
directly by them.
Third, listeners of the notification chain do not need to each parse the
relatively complex nexthop code structures. They are passing the
required information in a simplified way.
Note that a single 'has_encap' bit is added instead of the actual
encapsulation information since current listeners do not support such
nexthops.
Changes since RFC:
* s/is_encap/has_encap/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-11-03
This series includes updates to mlx5 software steering component.
1) Few improvements in the DR area, such as removing unneeded checks,
renaming to better general names, refactor in some places, etc.
2) Software steering (DR) Memory management improvements
This patch series contains SW Steering memory management improvements:
using buddy allocator instead of an existing bucket allocator, and
several other optimizations.
The buddy system is a memory allocation and management algorithm
that manages memory in power of two increments.
The algorithm is well-known and well-described, such as here:
https://en.wikipedia.org/wiki/Buddy_memory_allocation
Linux uses this algorithm for managing and allocating physical pages,
as described here:
https://www.kernel.org/doc/gorman/html/understand/understand009.html
In our case, although the algorithm in principal is similar to the
Linux physical page allocator, the "building blocks" and the circumstances
are different: in SW steering, buddy allocator doesn't really allocates
a memory, but rather manages ICM (Interconnect Context Memory) that was
previously allocated and registered.
The ICM memory that is used in SW steering is always power
of 2 (order), so buddy system is a good fit for this.
Patches in this series:
[PATH 4] net/mlx5: DR, Add buddy allocator utilities
This patch adds a modified implementation of a well-known buddy allocator,
adjusted for SW steering needs: the algorithm in principal is similar to
the Linux physical page allocator, but in our case buddy allocator doesn't
really allocate a memory, but rather manages ICM memory that was previously
allocated and registered.
[PATH 5] net/mlx5: DR, Handle ICM memory via buddy allocation instead of bucket management
This patch changes ICM management of SW steering to use buddy-system mechanism
Instead of the previous bucket management.
[PATH 6] net/mlx5: DR, Sync chunks only during free
This patch makes syncing happen only when freeing memory chunks.
[PATH 7] net/mlx5: DR, ICM memory pools sync optimization
This patch adds tracking of pool's "hot" memory and makes the
check whether steering sync is required much shorter and faster.
[PATH 8] net/mlx5: DR, Free buddy ICM memory if it is unused
This patch adds tracking buddy's used ICM memory,
and frees the buddy if all its memory becomes unused.
3) Misc code cleanups
* tag 'mlx5-updates-2020-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net: mlx5: Replace in_irq() usage
net/mlx5: Cleanup kernel-doc warnings
net/mlx4: Cleanup kernel-doc warnings
net/mlx5e: Validate stop_room size upon user input
net/mlx5: DR, Free unused buddy ICM memory
net/mlx5: DR, ICM memory pools sync optimization
net/mlx5: DR, Sync chunks only during free
net/mlx5: DR, Handle ICM memory via buddy allocation instead of buckets
net/mlx5: DR, Add buddy allocator utilities
net/mlx5: DR, Rename matcher functions to be more HW agnostic
net/mlx5: DR, Rename builders HW specific names
net/mlx5: DR, Remove unused member of action struct
====================
Link: https://lore.kernel.org/r/20201105201242.21716-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds a new network driver implementing MHI transport for
network packets. Packets can be in any format, though QMAP (rmnet)
is the usual protocol (flow control + PDN mux).
It support two MHI devices, IP_HW0 which is, the path to the IPA
(IP accelerator) on qcom modem, And IP_SW0 which is the software
driven IP path (to modem CPU).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function can be used by client driver to determine whether it's
possible to queue new elements in a channel ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ioana Ciornei says:
====================
net: phy: add support for shared interrupts (part 1)
This patch set aims to actually add support for shared interrupts in
phylib and not only for multi-PHY devices. While we are at it,
streamline the interrupt handling in phylib.
For a bit of context, at the moment, there are multiple phy_driver ops
that deal with this subject:
- .config_intr() - Enable/disable the interrupt line.
- .ack_interrupt() - Should quiesce any interrupts that may have been
fired. It's also used by phylib in conjunction with .config_intr() to
clear any pending interrupts after the line was disabled, and before
it is going to be enabled.
- .did_interrupt() - Intended for multi-PHY devices with a shared IRQ
line and used by phylib to discern which PHY from the package was the
one that actually fired the interrupt.
- .handle_interrupt() - Completely overrides the default interrupt
handling logic from phylib. The PHY driver is responsible for checking
if any interrupt was fired by the respective PHY and choose
accordingly if it's the one that should trigger the link state machine.
From my point of view, the interrupt handling in phylib has become
somewhat confusing with all these callbacks that actually read the same
PHY register - the interrupt status. A more streamlined approach would
be to just move the responsibility to write an interrupt handler to the
driver (as any other device driver does) and make .handle_interrupt()
the only way to deal with interrupts.
Another advantage with this approach would be that phylib would gain
support for shared IRQs between different PHY (not just multi-PHY
devices), something which at the moment would require extending every
PHY driver anyway in order to implement their .did_interrupt() callback
and duplicate the same logic as in .ack_interrupt(). The disadvantage
of making .did_interrupt() mandatory would be that we are slightly
changing the semantics of the phylib API and that would increase
confusion instead of reducing it.
What I am proposing is the following:
- As a first step, make the .ack_interrupt() callback optional so that
we do not break any PHY driver amid the transition.
- Every PHY driver gains a .handle_interrupt() implementation that, for
the most part, would look like below:
irq_status = phy_read(phydev, INTR_STATUS);
if (irq_status < 0) {
phy_error(phydev);
return IRQ_NONE;
}
if (!(irq_status & irq_mask))
return IRQ_NONE;
phy_trigger_machine(phydev);
return IRQ_HANDLED;
- Remove each PHY driver's implementation of the .ack_interrupt() by
actually taking care of quiescing any pending interrupts before
enabling/after disabling the interrupt line.
- Finally, after all drivers have been ported, remove the
.ack_interrupt() and .did_interrupt() callbacks from phy_driver.
This patch set is part 1 and it addresses the changes needed in phylib
and 7 PHY drivers. The rest can be found on my Github branch here:
https://github.com/IoanaCiornei/linux/commits/phylib-shared-irq
I do not have access to most of these PHY's, therefore I Cc-ed the
latest contributors to the individual PHY drivers in order to have
access, hopefully, to more regression testing.
Changes in v2:
- Rework the .handle_interrupt() implementation for each driver so that
only the enabled interrupts are taken into account when
IRQ_NONE/IRQ_HANDLED it returned. The main idea is so that we avoid
falsely blaming a device for triggering an interrupt when this is not
the case.
The only devices for which I was unable to make this adjustment were
the BCM8706, BCM8727, BCMAC131 and BCM5241 since I do not have access
to their datasheets.
- I also updated the pseudo-code added in the cover-letter so that it's
more clear how a .handle_interrupt() callback should look like.
====================
Tested-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201101125114.1316879-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Michael Walle <michael@walle.cc>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.
After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.
For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.
At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.
To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.
Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet(6)_skb_parm was removed from sctp_input_cb by Commit a1dd2cf2f1ae
("sctp: allow changing transport encap_port by peer packets"), as it
thought sctp_input_cb->header is not used any more in SCTP.
syzbot reported a crash:
[ ] BUG: KASAN: use-after-free in decode_session6+0xe7c/0x1580
[ ]
[ ] Call Trace:
[ ] <IRQ>
[ ] dump_stack+0x107/0x163
[ ] kasan_report.cold+0x1f/0x37
[ ] decode_session6+0xe7c/0x1580
[ ] __xfrm_policy_check+0x2fa/0x2850
[ ] sctp_rcv+0x12b0/0x2e30
[ ] sctp6_rcv+0x22/0x40
[ ] ip6_protocol_deliver_rcu+0x2e8/0x1680
[ ] ip6_input_finish+0x7f/0x160
[ ] ip6_input+0x9c/0xd0
[ ] ipv6_rcv+0x28e/0x3c0
It was caused by sctp_input_cb->header/IP6CB(skb) still used in sctp rx
path decode_session6() but some members overwritten by sctp6_rcv().
This patch is to fix it by bring inet(6)_skb_parm back to sctp_input_cb
and not overwriting it in sctp4/6_rcv() and sctp_udp_rcv().
Reported-by: syzbot+5be8aebb1b7dfa90ef31@syzkaller.appspotmail.com
Fixes: a1dd2cf2f1ae ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/136c1a7a419341487c504be6d1996928d9d16e02.1604472932.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kurt Kanzenbach says:
====================
Hirschmann Hellcreek DSA driver
this series adds a DSA driver for the Hirschmann Hellcreek TSN switch
IP. Characteristics of that IP:
* Full duplex Ethernet interface at 100/1000 Mbps on three ports
* IEEE 802.1Q-compliant Ethernet Switch
* IEEE 802.1Qbv Time-Aware scheduling support
* IEEE 1588 and IEEE 802.1AS support
That IP is used e.g. in
https://www.arrow.com/en/campaigns/arrow-kairos
Due to the hardware setup the switch driver is implemented using DSA. A special
tagging protocol is leveraged. Furthermore, this driver supports PTP and
hardware timestamping.
This work is part of the AccessTSN project: https://www.accesstsn.com/
The previous versions can be found here:
* https://lkml.kernel.org/netdev/20200618064029.32168-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20200710113611.3398-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20200723081714.16005-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20200820081118.10105-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20200901125014.17801-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20200904062739.3540-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20201004112911.25085-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/20201028074221.29326-1-kurt@linutronix.de/
Changes since v7:
* Simplify tagging code (rebase to net-next)
* Pass info instead of ptr (Florian Fainelli)
* Fix yamllint warnings (Rob Herring)
Changes since v6:
* Add .tail_tag = true (Vladimir Oltean)
* Fix vlan_filtering=0 bridges (Vladimir Oltean)
* Enforce restrictions (Vladimir Oltean)
* Sort stuff alphabetically (Vladimir Oltean)
* Rename hellcreek.yaml to hirschmann,hellcreek.yaml
* Typo fixes
Changes since v5:
* Implement configure_vlan_while_not_filtering behavior (Vladimir Oltean)
* Minor cleanups
Changes since v4:
* Fix W=1 compiler warnings (kernel test robot)
* Add tags
Changes since v3:
* Drop TAPRIO support (David Miller)
=> Switch to mutexes due to the lack of hrtimers
* Use more specific compatible strings and add platform data (Andrew Lunn)
* Fix Kconfig ordering (Andrew Lunn)
Changes since v2:
* Make it compile by getting all requirements merged first (Jakub Kicinski, David Miller)
* Use "tsn" for TSN register set (Rob Herring)
* Fix DT binding issues (Rob Herring)
Changes since v1:
* Code simplifications (Florian Fainelli, Vladimir Oltean)
* Fix issues with hellcreek.yaml bindings (Florian Fainelli)
* Clear reserved field in ptp v2 event messages (Richard Cochran)
* Make use of generic ptp parsing function (Richard Cochran, Vladimir Oltean)
* Fix Kconfig (Florian Fainelli)
* Add tags (Florian Fainelli, Rob Herring, Richard Cochran)
Changes since RFC ordered by reviewers:
* Andrew Lunn
* Use dev_dbg for debug messages
* Get rid of __ function names where possible
* Use reverse xmas tree variable ordering
* Remove redundant/useless checks
* Improve comments e.g. for PTP
* Fix Kconfig ordering
* Make LED handling more generic and provide info via DT
* Setup advertisement of PHYs according to hardware
* Drop debugfs patch
* Jakub Kicinski
* Fix compiler warnings
* Florian Fainelli
* Switch to YAML DT bindings
* Richard Cochran
* Fix typo
* Add missing NULL checks
====================
Link: https://lore.kernel.org/r/20201103071101.3222-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add basic documentation and example.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hirschmann is building devices for automation and networking. Add them to the
vendor prefixes.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch has two controllable I/Os which are usually connected to LEDs. This
is useful to immediately visually see the PTP status.
These provide two signals:
* is_gm
This LED can be activated if the current device is the grand master in that
PTP domain.
* sync_good
This LED can be activated if the current device is in sync with the network
time.
Expose these via the LED framework to be controlled via user space
e.g. linuxptp.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch has the ability to take hardware generated time stamps per port for
PTPv2 event messages in Rx and Tx direction. That is useful for achieving needed
time synchronization precision for TSN devices/switches. So add support for it.
There are two directions:
* RX
The switch has a single register per port to capture a timestamp. That
mechanism is not used due to correlation problems. If the software processing
is too slow and a PTPv2 event message is received before the previous one has
been processed, false timestamps will be captured. Therefore, the switch can
do "inline" timestamping which means it can insert the nanoseconds part of
the timestamp directly into the PTPv2 event message. The reserved field (4
bytes) is leveraged for that. This might not be in accordance with (older)
PTP standards, but is the only way to get reliable results.
* TX
In Tx direction there is no correlation problem, because the software and the
driver has to ensure that only one event message is "on the fly". However,
the switch provides also a mechanism to check whether a timestamp is
lost. That can only happen when a timestamp is read and at this point another
message is timestamped. So, that lost bit is checked just in case to indicate
to the user that the driver or the software is somewhat buggy.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|