aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-12-01rt2x00: use timeout in rt2x00usb_vendor_requestStanislaw Gruszka
Use provided timeout value in rt2x00usb_vendor_request() instead of iterating REGISTER_BUSY_COUNT times. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-12-01brcmsmac: extend hardware info shown in debugfsArend van Spriel
The hardware info now also include radio and phy information, which can be helpful in debugging issues. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-12-01brcmutil: add helper function to format board revisionArend van Spriel
The board revision that is available in hardware can be translated so it matches the labelling on the board. This is accomplished by this helper function. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-12-01rt2800: calculate tx power temperature compensation on selected chipsStanislaw Gruszka
Currently implemented temperature compensation is only valid on some of supported chips. Other chips do not need temperature compensation or need different way to do this (not yet implemented in the rt2800 driver). Trying to do run rt2800_get_gain_calibration_delta() when this is not appropriate on particular chip gives bogus result of TX power and can make connection unstable. This is follow up to commit 8c8d2017ba25c510ddf093419048460db1109bc4 "rt2800: fix RT5390 & RT3290 TX power settings regression". On that commit we avoid setting BBP_R1 register, but the real problem is wrong temperature compensation calculation. Reported-and-tested-by: Ronald Wahl <ronald.wahl@raritan.com> Debugged-by: Ronald Wahl <ronald.wahl@raritan.com> Cc: Mike Romberg <mike-romberg@comcast.net> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-12-01wil6210: Fix potential memory leaks on error pathsLino Sanfilippo
Fix missing memory deallocation on error paths in wil_write_file_wmi() and wil_write_file_txmgmt(). Reported-by: Ahmed Tamrawi <ahmedtamrawi@gmail.com> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-12-01Merge branch 'for-linville' of git://github.com/kvalo/athJohn W. Linville
2014-12-01Merge branch 'for-upstream' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2014-12-01ath10k: simplify rx ring size/fill calculationMichal Kazior
Don't bother with fancy arithmetic and just hardcode the final values. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: prevent pci tx/rx starvationMichal Kazior
In theory it was possible to starve the system if a tx/rx handler could implicitly trigger more tx/rx pci events. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: remove transfer_id from ath10k_hif_cb::tx_completionMichal Kazior
Pass the eid argument via skbuff control buffer. This will make it possible to work with queues of HTC event buffers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: remove unused callback argument from struct ath10k_hif_cb::rx_completionMichal Kazior
This wasn't used since forever and there are no plans on using it. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: make wmi service bitmap non-debugMichal Kazior
The service bitmap can be used to determine firmware capabilities. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: add sanity checks for service bmap parsingMichal Kazior
This shouldn't really happen but take into account the original service bitmap length when mapping service ids. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: fix wmi svc bitmap dbg printMichal Kazior
The dump print uses sizeof() but since service_map was a mere pointer the dump was too short. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: add pointer constness to tracesMichal Kazior
Traces shouldn't modified passed data. This will make it possible to pass const arguments to traces. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-12-01ath10k: do not limit RTS threshold value to 2347Vivek Natarajan
Increase the rts threshold from the legacy value of 2347 to support higher threshold limit. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-27Bluetooth: Automatically flushable packets aren't allowed on LE linksSteven Walter
The Bluetooth spec states that automatically flushable packets may not be sent over a LE-U link. Signed-off-by: Steven Walter <stevenrwalter@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-11-26Bluetooth: ath3k: Add support of MCI 13d3:3408 bt deviceDmitry Tunin
Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This Bluetooth module requires loading patch and sysconfig by ath3k driver. T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3408 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
2014-11-26ath10k: fix station count enforcementMichal Kazior
The number of peers isn't directly translatable to the number of stations because ath10k needs to reserve a few extra peers for special cases like multi-vif concurrency. The previous limit was 126 and 15 stations in AP mode for 10.x and main firmware branches respectively. The limit is now 128 and 16 which was the original intention. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: clean up num_peers lockingMichal Kazior
The var was supposed to be protected by data_lock but it wasn't so in all instances. It's actually not necessary to have a spinlock protected num_peers so drop it. All instances of num_peers are already within conf_mutex sections so use that. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: add missing gotoMichal Kazior
This prevents warning spamming if peer creation fails during sta_state in some cases. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: add memory dump debugfs interfaceYanbo Li
Add mem_val debugfs file for dumping the firmware (target) memory and also for writing to the memory. The firmware memory is accessed through one file which uses position of the file as the firmware memory address. For example, with dd use skip parameter for the address. Beucase target memory width is 32 bits it's strongly recommended to use blocksize divisable with 4 when using this interface. For example, when using dd use bs=4 to set the block size to 4 and remember to divide both count and skip values with four. To read 4 kB chunk from address 0x400000: dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1 To write value 0x01020304 to address 0x400400: echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832 To read 4 KB chunk of memory and then write back after edit: dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576 emacs tmp.bin dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576 Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: add register access debugfs interfaceYanbo Li
Debugfs files reg_addr and reg_val are used for reading and writing to the firmware (target) registers. reg_addr contains the address to be accessed, which also needs to be set first, and reg_value is when used for reading and writing the actual value in ASCII. To read a value from the firmware register 0x100000: # echo 0x100000 > reg_addr # cat reg_value 0x00100000:0x000002d3 To write value 0x2400 to address 0x100000: # echo 0x100000 > reg_addr # echo 0x2400 > reg_value # Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix bug reported by lockdepSujith Manoharan
ath10k_tx_wep_key_work() acquires conf_mutex, so cancelling it when conf_mutex is already taken in ath10k_remove_interface() is incorrect, so move it outside the lock. Snippet from the lockdep report: kernel: ====================================================== kernel: [ INFO: possible circular locking dependency detected ] kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O kernel: ------------------------------------------------------- kernel: hostapd/451 is trying to acquire lock: kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290 kernel: but task is already holding lock: kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core] kernel: which lock already depends on the new lock. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix locking for WEP keysSujith Manoharan
peer->keys needs to be protected by data_lock since it is also accessed from the WMI path. Both install() and clear() routines for peer keys modify the key contents, so use the data_lock to avoid races. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix shared WEPSujith Manoharan
When static keys are used in shared WEP, when a station is associated, message 3 is sent with an encrypted payload. But, for subsequent authentications that are triggered without a deauth, the auth frame is decrypted by the HW. To handle this, check if the WEP keys have already been set for the peer and if so, mark the frame as decrypted. This scenario can happen when a station changes its default TX key and initiates a new authentication sequence. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: don't drop corrupted mgmt framesMichal Kazior
Some firmware revisions don't seem to deilver management frames with FCS error via WMI so narrow down the HTT rule to not drop corrupted management frames. This basically increases number of frames ath10k reports while sniffing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix offchannel cancel failuresMichal Kazior
When mac80211 requests driver to cancel a hw roc the driver must not call the expired() callback or else roc will fail in some cases depending on how things get scheduled. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: make hw roc more reliableMichal Kazior
With P2P concurrency requested hw roc duration time can be very small. Some firmware revisions refuse scan requests with too small channel dwell time. This prevents messages like, e.g. with connected STA vif and performing P2P Find: ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan ieee80211 phy3: failed to start next HW ROC (-110) Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: fix offchan reliabilityMichal Kazior
New firmware revisions don't need peer creation when doing offchannel tx. Earlier revisions would queue and never release frames without a peer. This prevent new firmware revisions from stopping replenishing wmi-htc tx credits and improves reliability of offchannel tx which would sometimes silently fail. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: remove extra_tx_headroomMichal Kazior
Comment was out-of-date. The headroom is no longer necessary because HTT Tx fragment list is stored in dma pool item associated with each sk_buff. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: use configured nss instead of max nssBen Greear
When re-associating a station, the nss was set back to maximum value even if user had configured small number of tx chains. So, pay attention to user's config in this case as well. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26ath10k: apply chainmask settings to vdev on creationBen Greear
It appears it takes more than just setting the hardware's chainmask to make things work well. Without this patch, a vdev would only use 1x1 rates when chainmask was set to 0x3. Setting the 'nss' (number of spatial streams) on the vdev helps the firmware's rate-control algorithm work properly. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-26mac802154: remove unnecessary if statementVarka Bhadram
Removes unnecessary if statement check for net device. Error check performed after alloc_netdev(). ndev = alloc_netdev(sizeof(*sdata) + local->hw.vif_data_size, name, NET_NAME_UNKNOWN, ieee802154_if_setup); if (!ndev) return ERR_PTR(-ENOMEM); .. Signed-off-by: Varka Bhadram <varkab@cdac.in> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-26ieee802154: fix spelling mistakesVarka Bhadram
Signed-off-by: Varka Bhadram <varkab@cdac.in> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-11-25mwifiex: add Tx status support for ACTION framesAmitkumar Karwar
ACK status (0/1) for ACTION frames is informed to cfg80211. We will extend existing logic used for EAPOL frames. The cfg80211 API is different here. Also, we need to explicitly free cloned skb. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: add Tx status support for EAPOL packetsAmitkumar Karwar
Firmware notifies the driver through event if EAPOL data packet has been acked or not. We will inform this status to userspace listening on a socket. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: skip delay main work logic for USB interface.Amitkumar Karwar
We had introduced delay main work logic to avoid processing interrupts when Rx pending packet count reaches high threshold. interrupt processing is restarted later when packet count reduces lower threashold. This helped to reduce unnecessary overhead and improve throughput for SD and PCIe chipsets. As there are no interrupts for USB, we will skip this logic for USB chipsets. Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: fix scan problem on big endian platformsAmitkumar Karwar
This patch adds missing endian conversion for beacon size while processing scan response. Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com> Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25mwifiex: fix sparse warningAmitkumar Karwar
This patch fixes following sparse warnings: drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16 drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25ath9k: add TPC capability to TX descriptor pathLorenzo Bianconi
Add TPC capability to TX descriptor path. Cap per-packet TX power according to TX power per-rate tables. Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25ath9k: add TX power per-rate tablesLorenzo Bianconi
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to cap the maximum TX power value per-rate in the TX descriptor path. Cap TX power for self generated frames (ACK, RTS/CTS). Currently TPC is supported just by AR9003 based chips Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-25brcmfmac: correct .disconnect() callback while connectingArend van Spriel
When the driver has sent a join iovar to the firmware it waits for the events to report result of the connection. However, the wpa_supplicant will request a .disconnect() after a timeout. So upon calling .disconnect() the interface state may still be CONNECTING. Clear the CONNECTING bit as well. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24net: wireless: rtlwifi: rtl8192ee: Fix compilation of the driverAndreas Ruprecht
In the Makefile for this driver, the wrong Kconfig option is used to trigger the compilation of the object file. This leads to the driver only being included into the kernel when both CONFIG_RTL8821AE and CONFIG_RTL8192AE are set to "y". Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24net: wireless: rtlwifi: Do not always include drivers in obj-mAndreas Ruprecht
In four of the rtlwifi drivers, the Makefile contains superfluous statements indicating the compilation of the driver as an LKM regardless of the corresponding Kconfig option. If the corresponding option is set to 'y', the build system will then see the object file in obj-m and obj-y, which leads to a compilation as a built-in only. Even though this leads to the desired behavior, the unconditional appearance in obj-m is confusing for someone reading the Makefile. This patch removes the superfluous Makefile statements. Signed-off-by: Andreas Ruprecht <rupran@einserver.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24ath: Fix a false radar detection patternVivek Natarajan
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be interchanged leading to frequent incorrect radar detections. Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24wireless/p54: Remove duplicated net2280 headerRicardo Ribalda Delgado
The usb gadget driver net2280 has exported a header file with the register definition of the net2280 chip. Remove the custom/duplicated header file in favor of that header file in include/linux Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24rtlwifi: update RCR register in rtl_op_configure_filter()Lorenzo Bianconi
Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX filter configuration Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24brcmfmac: fix static checker warning in pmklist handlingArend van Spriel
The patch fixes a static checker warning: drivers/net/wireless/brcm80211/brcmfmac/cfg80211.c:2965 brcmf_cfg80211_set_pmksa() warn: can 'pmkid_len' be negative? The answer to the question above is likely no so changing its type to unsigned is sufficient. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-24Merge tag 'iwlwifi-next-for-john-2014-11-24' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Emmanuel Grumbach <egrumbach@gmail.com> says: "Major works are CSA and TDLS. On top of that I have a new firmware API for scan and a few rate control improvements. Johannes find a few tricks to improve our CPU utilization and adds support for a new spin of 7265 called 7265D. Along with this a few random things that don't stand out." Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-12 04:37:44 +0000