| Age | Commit message (Collapse) | Author |
|---|
|
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.
This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In the xmit patch we are sending a -EXXX value to iscsi_conn_failure
which is causing userspace to get confused.
We should be sending a ISCSI_ERR_* value that userspace understands.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
IOP reset message should be posted to inbound message register
instead of outbound message register.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The follow patch fixes a problem for Matt Taggart.
The Compaq system he had (dl380?) has a SmartArray device that exposes
the 53c1510 device in both RAID and "normal" modes. The difference
is in RAID mode, the smart array driver (IIRC) should claim the
device instead of sym2 driver. Patch below prevents sym2 from
claiming the device when the RAID "daughter board" is attached.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This fixes three drivers to compile again after my patch that removes
the data_cmnd member from struct scsi_cmnd.
The fas216 change is trivial, it should have been using ->cmnd all the
time.
NCR53C9 (which seem to be mostly duplicate driver with esp.c!) is doing
something odd, it should only have looked at ->cmnd before not the saved
copy that is kept for the error handlers sake. Note that it really
should deal with the sync setting themselves but use the generic domain
validation code that get this right - but that's for later let's push
this simple compile fix for now.
And sorry for the late fix for this, I have been busy with OLS and
associated activities last week.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI] esp: Fix build.
[SPARC]: Fix SA_STATIC_ALLOC value.
[SPARC64]: Explicitly print return PC when the kernel fault PC is bogus.
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4/IPV6]: Setting 0 for unused port field in RAW IP recvmsg().
[IPV4] ipmr: ip multicast route bug fix.
[TG3]: Update version and reldate
[TG3]: Handle tg3_init_rings() failures
[TG3]: Add tg3_restart_hw()
[IPV4]: Clear the whole IPCB, this clears also IPCB(skb)->flags.
[IPV6]: Clean skb cb on IPv6 input.
[NETFILTER]: Demote xt_sctp to EXPERIMENTAL
[NETFILTER]: bridge netfilter: add deferred output hooks to feature-removal-schedule
[NETFILTER]: xt_pkttype: fix mismatches on locally generated packets
[NETFILTER]: SNMP NAT: fix byteorder confusion
[NETFILTER]: conntrack: fix SYSCTL=n compile
[NETFILTER]: nf_queue: handle NF_STOP and unknown verdicts in nf_reinject
[NETFILTER]: H.323 helper: fix possible NULL-ptr dereference
|
|
The patch below moves the cpu hotplugging higher up in the cpufreq
layering; this is needed to avoid recursive taking of the cpu hotplug
lock and to otherwise detangle the mess.
The new rules are:
1. you must do lock_cpu_hotplug() around the following functions:
__cpufreq_driver_target
__cpufreq_governor (for CPUFREQ_GOV_LIMITS operation only)
__cpufreq_set_policy
2. governer methods (.governer) must NOT take the lock_cpu_hotplug()
lock in any way; they are called with the lock taken already
3. if your governer spawns a thread that does things, like calling
__cpufreq_driver_target, your thread must honor rule #1.
4. the policy lock and other cpufreq internal locks nest within
the lock_cpu_hotplug() lock.
I'm not entirely happy about how the __cpufreq_governor rule ended up
(conditional locking rule depending on the argument) but basically all
callers pass this as a constant so it's not too horrible.
The patch also removes the cpufreq_governor() function since during the
locking audit it turned out to be entirely unused (so no need to fix it)
The patch works on my testbox, but it could use more testing
(otoh... it can't be much worse than the current code)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
From: Tetsuo Handa from-linux-kernel@i-love.sakura.ne.jp
The recvmsg() for raw socket seems to return random u16 value
from the kernel stack memory since port field is not initialized.
But I'm not sure this patch is correct.
Does raw socket return any information stored in port field?
[ BSD defines RAW IP recvmsg to return a sin_port value of zero.
This is described in Steven's TCP/IP Illustrated Volume 2 on
page 1055, which is discussing the BSD rip_input() implementation. ]
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP multicast route code was reusing an skb which causes use after free
and double free.
From: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Note, it is real skb_clone(), not alloc_skb(). Equeued skb contains
the whole half-prepared netlink message plus room for the rest.
It could be also skb_copy(), if we want to be puristic about mangling
cloned data, but original copy is really not going to be used.
Acked-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update version to 3.63.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.
Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.
Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CIC_SEEKY() test really wants to use the minimum of either:
- 2 msecs (not jiffies)
- or, the pending slice time
So code it like that.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
It should be toggling the same bit on and off, fix it up.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
We need to postpone the queue startup until after the softirq
handler has actually finished some requests, otherwise we could
be racing with cciss_softirq_done() and not actually restart
the queue handling.
Signed-off-by: Jens Axboe <axboe@suse.de>
|
|
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear the accumulated junk in IP6CB when starting to handle an IPV6
packet.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the recent problems with all the SCTP stuff it seems reasonable
to mark this as experimental.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
feature-removal-schedule
Add bridge netfilter deferred output hooks to feature-removal-schedule
and disable them by default. Until their removal they will be
activated by the physdev match when needed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Locally generated broadcast and multicast packets have pkttype set to
PACKET_LOOPBACK instead of PACKET_BROADCAST or PACKET_MULTICAST. This
causes the pkttype match to fail to match packets of either type.
The below patch remedies this by using the daddr as a hint as to
broadcast|multicast. While not pretty, this seems like the only way
to solve the problem short of just noting this as a limitation of the
match.
This resolves netfilter bugzilla #484
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of an unknown verdict or NF_STOP the packet leaks. Unknown verdicts
can happen when userspace is buggy. Reinject the packet in case of NF_STOP,
drop on unknown verdicts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An RCF message containing a timeout results in a NULL-ptr dereference if
no RRQ has been seen before.
Noticed by the "SATURN tool", reported by Thomas Dillig <tdillig@stanford.edu>
and Isil Dillig <isil@stanford.edu>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data_cmd[] member got deleted, so do not use it any more. Scsi
commands do not have their ->cmd[] overwritten temporary to probe for
status after an error before retrying.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It alises IRQF_SHARED which causes all kinds of
problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That way we'll have at least some debugging info even if
the stack dump explodes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_alloc_skb is designated for RX descriptors, not TX. (Some drivers
use it for the latter anyway, but that's a different story)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skbuff.h has an #ifndef CONFIG_HAVE_ARCH_DEV_ALLOC_SKB to allow
architectures to reimplement __dev_alloc_skb. It's not set on any
architecture and now that we have an architecture-overrideable
NET_SKB_PAD there is not point at all to have one either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the queue of the underlying device is stopped at initialization time
or the device is marked "not present", the state will be propagated to the
vlan device and never change. Based on an analysis by Patrick McHardy.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't compile, and it's dubious in several regards:
1) is enabled by non-Kconfig controlled CONFIG_* value
(noted by Randy Dunlap)
2) XFRM6_TUNNEL_SPI_MAGIC is defined after it's first use
3) the debugging messages print object pointer addresses
which have no meaning without context
So let's just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom dongles with HID proxy support actually support SCO over
HCI if the SCO buffer size values are corrected. So instead of disabling
the SCO support, mark this dongle with the quirk for the Bluetooth core
to correct the wrong buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch disables the ISOC transfers for another broken RTX Telecom
based USB dongle. Starting the USB ISOC transfers only ends in a burst
of error messages for invalid SCO packets on connection handle 0.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Belkin F8T012 and F8T013 devices are both based on a Bluetooth chip
from Broadcom and their SCO buffer size values are wrong. The Bluetooth
core should correct these values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The SCO buffer size values on IBM/Lenovo ThinkPad laptops with a
Bluetooth chip from Broadcom are wrong. The USB Bluetooth driver
has to set a quirk to correct the SCO buffer size values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some Bluetooth RFCOMM implementations try to negotiate a bigger channel
MTU than we can support for a particular session. The maximum MTU for
a RFCOMM session is limited through the L2CAP layer. So if the other
side proposes a channel MTU that is bigger than the underlying L2CAP
MTU, we should reduce it to the L2CAP MTU of the session minus five
bytes for the RFCOMM headers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In PSCHED_TADD and PSCHED_TADD2, if delta is less than tv.tv_usec (so,
less than USEC_PER_SEC too) then tv_res will be smaller than tv. The
affectation "(tv_res).tv_usec = __delta;" is wrong. The fix is to
revert to the original code before
4ee303dfeac6451b402e3d8512723d3a0f861857 and change the 'if' in
'while'.
[Shuya MAEDA: "while (__delta >= USEC_PER_SEC){ ... }" instead of
"while (__delta > USEC_PER_SEC){ ... }"]
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the default sequence window size (100) I got the following in
my logs:
Jun 22 14:24:09 localhost kernel: [ 1492.114775] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674749) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206548), sending SYNC...
Jun 22 14:24:09 localhost kernel: [ 1492.115147] DCCP: Step 6 failed for
DATA packet, (LSWL(6279674225) <= P.seqno(6279674750) <=
S.SWH(6279674324)) and (P.ackno doesn't exist or LAWL(18798206530) <=
P.ackno(1125899906842620) <= S.AWH(18798206549), sending SYNC...
I went to alter the default sysctl and it didn't take for new sockets.
Below patch fixes this.
I think the default is too low but it is what the DCCP spec specifies.
As a side effect of this my rx speed using iperf goes from about 2.8 Mbits/sec
to 3.5. This is still far too slow but it is a step in the right direction.
Compile tested only for IPv6 but not particularly complex change.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The neighbour ha field may get updated without destroying the
neighbour. In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Need to set mcast->ah before debug code dereferences it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Validate MADs sent by userspace clients for spec compliance with
C13-18.1.1 (prevent duplicate requests and responses sent on the
same port). Without this, RMPP transactions get aborted because
of duplicate packets.
This patch is similar to that provided by Jack Morgenstein.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipath_skip_sge() doesn't exactly duplicate the side effects of
ipath_copy_sge() if num_sge > 1 since it doesn't decrement ss->num_sge.
This could result in the sg_list being accessed out of bounds.
Since ipath_skip_sge() is almost always called with num_sge == 1,
the original "optimization" is almost never used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
I am still working on a proposal to remove the phys_to_virt() calls
in the ib_ipath driver. In the mean time, this patch allows SRP
to work by fixing the R_Key check and conversion from IB address
to kernel virtual address. It also returns the correct page size
for FMRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Mem-free HCAs always keep one spare SRQ WQE, so the SRQ limit cannot
be set beyond srq->max - 1.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Lockdep warns because uverbs is trying to take uobj->mutex when it
already holds that lock. This is because there are really multiple
types of uobjs even though all of their locks are initialized in
common code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ib_uverbs_create_ah() and ib_uverbs_create_srq() did not release the
PD's read lock in their error paths, which lead to deadlock when
destroying the PD.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix ABBA deadlock between lock_cpu_hotplug() and the cpuset
callback_mutex lock.
It only happens on cpu_exclusive cpusets, due to the dynamic
sched domain code trying to take the cpu hotplug lock inside
the cpuset callback_mutex lock.
This bug has apparently been here for several months, but didn't
get hit until the right customer load on a large system.
This fix appears right from inspection, but it will take a few
more days running it on that customers workload to be confident
we nailed it. We don't have any other reproducible test case.
The cpu_hotplug_lock() tends to cover large runs of code.
The other places that hold both that lock and the cpuset callback
mutex lock always nest the cpuset lock inside the hotplug lock.
This place tries to do the reverse, risking an ABBA deadlock.
This is in the cpuset_rmdir() code, where we:
* take the callback_mutex lock
* mark the cpuset CS_REMOVED
* call update_cpu_domains for cpu_exclusive cpusets
* in that call, take the cpu_hotplug lock if the
cpuset is marked for removal.
Thanks to Jack Steiner for identifying this deadlock.
The fix is to tear down the dynamic sched domain before we grab
the cpuset callback_mutex lock. This way, the two locks are
serialized, with the hotplug lock taken and released before
trying for the cpuset lock.
I suspect that this bug was introduced when I changed the
cpuset locking from one lock to two. The dynamic sched domain
dependency on cpu_exclusive cpusets and its hotplug hooks were
added to this code earlier, when cpusets had only a single lock.
It may well have been fine then.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
