| Age | Commit message (Collapse) | Author |
|---|
|
Before the vendor specific setup stage is triggered call back into the
core to trigger an internal notification event. That event is used to
send an index update to the monitor interface. With that specific event
it is possible to update userspace with manufacturer information before
any HCI command has been executed. This is useful for early stage
debugging of vendor specific initialization sequences.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
BugLink: https://bugs.launchpad.net/bugs/1506615
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
|
|
This adapter works with the existing linux-firmware.
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0930 ProdID=021c Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
BugLink: https://bugs.launchpad.net/bugs/1502781
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
|
|
Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop
and noticed it doesn't work automatically, because the USB IDs are missing
from btusb.c.
Plugging in the adapter on Linux 4.1 (dmesg):
usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
/sys/kernel/debug/usb/devices:
T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=105b ProdID=e065 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM43142A0
S: SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Support for the chipset was added in commit 88f9b65 and a similar BCM43142
based device was added in commit 8f0c304.
To work around the issue, I got the firmware
(BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom
bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it
in /lib/firmware/brcm/BCM.hcd. After that:
$ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id
...(plug in the adapter)
usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Bluetooth: hci0: BCM: chip id 70
Bluetooth: hci0: BCM (001.001.011) build 0000
bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd
Bluetooth: hci0: BCM (001.001.011) build 0154
Bam, now it works for me!
/sys/kernel/debug/usb/devices:
T: Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=105b ProdID=e065 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM43142A0
S: SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Santtu Rekilä <sare@r00t3d.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
commit 5205185d461d5902325e457ca80bd421127b7308
Author: David Herrmann <dh.herrmann@gmail.com>
Date: Sat Apr 6 20:28:47 2013 +0200
Bluetooth: hidp: remove old session-management
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Cc: <stable@vger.kernel.org> # 3.10+
Reported-by: Mark Haun <haunma@keteu.org>
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The calculation for the firmware version number is off by one bit.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The BCM2045 seems to have a problem with the stored link key commands
and thus just mark them as broken.
HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
status 0x00
Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x2000
LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
Manufacturer: Broadcom Corporation (15)
HCI Event: Command Complete (0x0e) plen 11
Read Buffer Size (0x04|0x0005) ncmd 1
status 0x00
ACL MTU 1017:8 SCO MTU 64:0
HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
status 0x00
Commands: ffffff03feffcfffffffffff0300f8ff07
HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 2048
Error: Unsupported Feature or Parameter Value
From the looks of it, this device seems genuine and not one of the
devices that are neither Broadcom nor CSR devices in reality.
T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
Reported-and-tested-by: Julio González Mejías <juliolokooo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For Intel controllers the diagnostics settings are not persistent over
HCI Reset. So set the quirk to programm them again on every power up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:
warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':
This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.
Fixes: 91489919247a ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency")
Fixes: 943cc592195e ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The lock states from Intel SfP controllers can only be read once before
loading the firmware. So for debugging purposes, print them out.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
When using the HCI_CHANNEL_RAW, restrict the packet types to valid ones
from the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The HCI_VENDOR_PKT quirk was needed for BPA-100/105 devices that send
these messages. Now that there is support for proper diagnostic channel
this quirk is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The Broadcom Bluetooth USB devices have a third interface that is
dedicated for LM_DIAG messages. The If#= 2 describes this interface
and it consists of one bulk in and one bulk endpoint.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19ff ProdID=0239 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
For all Broadcom based devices with this interface, the driver now
claims it and schedules URBs for it. This allows to capture the
LM_DIAG messages and allows forwarding them via hci_recv_diag into
the diagnostic channel of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Selecting just BT_HCIUART_H4 is not enough and it also needs to select
BT_HCIUART to avoid this warning:
warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct
dependencies (NET && BT && BT_HCIUART)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
|
|
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Most relevantly, updates for the nfnetlink_log to integrate with
conntrack, fixes for cttimeout and improvements for nf_queue core, they are:
1) Remove useless ifdef around static inline function in IPVS, from
Eric W. Biederman.
2) Simplify the conntrack support for nfnetlink_queue: Merge
nfnetlink_queue_ct.c file into nfnetlink_queue_core.c, then rename it back
to nfnetlink_queue.c
3) Use y2038 safe timestamp from nfnetlink_queue.
4) Get rid of dead function definition in nf_conntrack, from Flavio
Leitner.
5) Attach conntrack support for nfnetlink_log.c, from Ken-ichirou MATSUZAWA.
This adds a new NETFILTER_NETLINK_GLUE_CT Kconfig switch that
controls enabling both nfqueue and nflog integration with conntrack.
The userspace application can request this via NFULNL_CFG_F_CONNTRACK
configuration flag.
6) Remove unused netns variables in IPVS, from Eric W. Biederman and
Simon Horman.
7) Don't put back the refcount on the cttimeout object from xt_CT on success.
8) Fix crash on cttimeout policy object removal. We have to flush out
the cttimeout extension area of the conntrack not to refer to an unexisting
object that was just removed.
9) Make sure rcu_callback completion before removing nfnetlink_cttimeout
module removal.
10) Fix compilation warning in br_netfilter when no nf_defrag_ipv4 and
nf_defrag_ipv6 are enabled. Patch from Arnd Bergmann.
11) Autoload ctnetlink dependencies when NFULNL_CFG_F_CONNTRACK is
requested. Again from Ken-ichirou MATSUZAWA.
12) Don't use pointer to previous hook when reinjecting traffic via
nf_queue with NF_REPEAT verdict since it may be already gone. This
also avoids a deadloop if the userspace application keeps returning
NF_REPEAT.
13) A bunch of cleanups for netfilter IPv4 and IPv6 code from Ian Morris.
14) Consolidate logger instance existence check in nfulnl_recv_config().
15) Fix broken atomicity when applying configuration updates to logger
instances in nfnetlink_log.
16) Get rid of the .owner attribute in our hook object. We don't need
this anymore since we're dropping pending packets that have escaped
from the kernel when unremoving the hook. Patch from Florian Westphal.
17) Remove unnecessary rcu_read_lock() from nf_reinject code, we always
assume RCU read side lock from .call_rcu in nfnetlink. Also from Florian.
18) Use static inline function instead of macros to define NF_HOOK() and
NF_HOOK_COND() when no netfilter support in on, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini found hang with rds-ping while testing RDS over TCP. Its
a corner case and doesn't happen always. The issue is not reproducible
with IB transport. Its clear from below dump why we see it with RDS TCP.
[<ffffffff8153b7e5>] do_tcp_setsockopt+0xb5/0x740
[<ffffffff8153bec4>] tcp_setsockopt+0x24/0x30
[<ffffffff814d57d4>] sock_common_setsockopt+0x14/0x20
[<ffffffffa096071d>] rds_tcp_xmit_prepare+0x5d/0x70 [rds_tcp]
[<ffffffffa093b5f7>] rds_send_xmit+0xd7/0x740 [rds]
[<ffffffffa093bda2>] rds_send_pong+0x142/0x180 [rds]
[<ffffffffa0939d34>] rds_recv_incoming+0x274/0x330 [rds]
[<ffffffff810815ae>] ? ttwu_queue+0x11e/0x130
[<ffffffff814dcacd>] ? skb_copy_bits+0x6d/0x2c0
[<ffffffffa0960350>] rds_tcp_data_recv+0x2f0/0x3d0 [rds_tcp]
[<ffffffff8153d836>] tcp_read_sock+0x96/0x1c0
[<ffffffffa0960060>] ? rds_tcp_recv_init+0x40/0x40 [rds_tcp]
[<ffffffff814d6a90>] ? sock_def_write_space+0xa0/0xa0
[<ffffffffa09604d1>] rds_tcp_data_ready+0xa1/0xf0 [rds_tcp]
[<ffffffff81545249>] tcp_data_queue+0x379/0x5b0
[<ffffffffa0960cdb>] ? rds_tcp_write_space+0xbb/0x110 [rds_tcp]
[<ffffffff81547fd2>] tcp_rcv_established+0x2e2/0x6e0
[<ffffffff81552602>] tcp_v4_do_rcv+0x122/0x220
[<ffffffff81553627>] tcp_v4_rcv+0x867/0x880
[<ffffffff8152e0b3>] ip_local_deliver_finish+0xa3/0x220
This happens because rds_send_xmit() chain wants to take
sock_lock which is already taken by tcp_v4_rcv() on its
way to rds_tcp_data_ready(). Commit db6526dcb51b ("RDS: use
rds_send_xmit() state instead of RDS_LL_SEND_FULL") which
was trying to opportunistically finish the send request
in same thread context.
But because of above recursive lock hang with RDS TCP,
the send work from rds_send_pong() needs to deferred to
worker to avoid lock up. Given RDS ping is more of connectivity
test than performance critical path, its should be ok even
for transport like IB.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing rule to export mpls iptunnel header needed by iproute2
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of commit fff326990789 ("tcp: reflect SYN queue_mapping into
SYNACK packets") we had little ways to cope with SYN floods.
We no longer need to reflect incoming skb queue mappings, and instead
can pick a TX queue based on cpu cooking the SYNACK, with normal XPS
affinities.
Note that all SYNACK retransmits were picking TX queue 0, this no longer
is a win given that SYNACK rtx are now distributed on all cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BITS_RX_EN is an 'unsigned long' constant, so the ones complement of that
has bits set that do not fit into a 32-bit variable on 64-bit architectures,
which causes a harmless gcc warning:
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c: In function 'hix5hd2_port_disable':
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:374:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~(BITS_RX_EN | BITS_TX_EN), priv->base + PORT_EN);
This adds a cast to (u32) to tell gcc that the code is indeed fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HNS MDIO driver fails to build on older ARM machines that are not
yet converted to CONFIG_OF:
drivers/net/ethernet/hisilicon/hns_mdio.c: In function 'hns_mdio_bus_name':
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: error: 'OF_BAD_ADDR' undeclared (first use in this function)
u64 taddr = OF_BAD_ADDR;
^
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/hisilicon/hns_mdio.c:409:11: error: implicit declaration of function 'of_translate_address' [-Werror=implicit-function-declaration]
taddr = of_translate_address(np, addr);
^
This clarifies the dependency to ensure we don't attempt to build these
drivers without CONFIG_OF, but also adds a COMPILE_TEST alternative to
give us better build coverage testing.
Build-tested on x86 as well to ensure this actually works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some configurations fail to build the hns dsaf code because of
a missing header file:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_init':
ethernet/hisilicon/hns/hns_dsaf_main.c:1096:2: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
priv->soft_mac_tbl = vzalloc(sizeof(*priv->soft_mac_tbl)
This adds the correct #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
yankejian says:
====================
net: hns: fixes two bugs in hns driver
This patchset fixes two bugs in hns driver.
- fixes timeout when received pause frame from the connective ports
- should be set by using ethtool -s when the devices are link down
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this patch fixes the bug triggered timeout sequence. when the connective
ports cannot accept the packets with higher speed, they will send out the
pause frame to the Soc's mac. At that time, the driver resets the relevant
of the Soc, then it causes the packets cannot be sent out immediately.
this patch fixes the issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
before this patch, hns driver only permits user to set the net device
by using ethtool -s when the device is link up. it is obviously not so
good. it needs to be set no matter it is link up or down. so this patch
fixes this issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Chenny Xu <chenny.xu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
huangdaode says:
====================
net: hisilicon fix some bugs in HNS drivers
This patchset fixes the two bugs in HNS driver, one is remove the hnae sysfs interface
according to the review comments from Arnd Bergmann <arnd@arndb.de>, another
is fixing the wrong mac_id judgement bug which is found during internal tests.
change log:
v3:
remove the hnae sysfs interface.
v2:
1) remove first bug fix, which is fixed in another patch submitted by
Arnd Bergmann <arnd@arndb.de>
2) change the code sytyle according to Joe.
v1:
initial version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the wrong judgement of mac_id when get port num.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the hns driver hnae sysfs interface according to
Arnd's review comments.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'bcm-phy-lib.c', added as a part of the commit
"net: phy: Add Broadcom phy library for common interfaces"
was missing the module license. This was causing an issue
when the library is built as a module; "module license
'unspecified' taints kernel".
This patch fixes the issue by adding the module license,
author and description to the bcm-phy-lib.c file.
Fixes: a1cba5613edf5 ("net: phy: Add Broadcom phy library for
common interfaces")
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A dhcp server may provide parameters to a client from a pool of IP
addresses and using a shared rootfs, or provide a specific set of
parameters for a specific client, usually using the MAC address to
identify each client individually. The dhcp protocol also specifies
a client-id field which can be used to determine the correct
parameters to supply when no MAC address is available. There is
currently no way to tell the kernel to supply a specific client-id,
only the userspace dhcp clients support this feature, but this can
not be used when the network is needed before userspace is available
such as when the root filesystem is on NFS.
This patch is to be able to do something like "ip=dhcp,client_id_type,
client_id_value", as a kernel parameter to enable the kernel to
identify itself to the server.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
|
|
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq/timer fixes from Thomas Gleixner:
"irq: a fix for the new hierarchical MSI interrupt handling which
unbreaks PCI=n configurations.
timers: a fix for the new hrtimer clock offset update mechanism to
ensure that the boot time offset is respected"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Increment clock_was_set_seq in timekeeping_init()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
This merge resolves conflicts with 75aec9df3a78 ("bridge: Remove
br_nf_push_frag_xmit_sk") as part of Eric Biederman's effort to improve
netns support in the network stack that reached upstream via David's
net-next tree.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/bridge/br_netfilter_hooks.c
|
