| Age | Commit message (Collapse) | Author |
|---|
|
'!' has higher precedence than comparisons so the original condition
is equivalent to "if (xspi->remaining_bytes == 0)". This makes the
static checkers complain.
xspi->remaining_bytes is signed and from looking at the code
briefly, I think it might be able to go negative. I suspect that
going negative may cause a bug, but I don't have the hardware and
can't test.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The ISR currently consumes the rx buffer data and re-enables transmission
from within interrupt context. This is bad because if the interrupt
occurs again before the ISR exits, the new interrupt will be erroneously
cleared by the still completing ISR.
Simplified the ISR by just setting the completion variable and exiting with
no action. Then just looped the transmit functionality in
xilinx_spi_txrx_bufs().
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
|
|
Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.
In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
resources (v2)
commit dc7dce280a
Author: Bjorn Helgaas <bhelgaas@google.com>
Date: Fri Oct 28 16:27:27 2011 -0600
parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
resources
Supply root bus resources to pci_create_root_bus() so they're correct
immediately. This fixes the problem of "early" and "header" quirks seeing
incorrect root bus resources.
added tests for elmmio_space.start while it should use
elmmio_space.flags. This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.
LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da43 "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).
This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
'boot_args' is an input args, and 'boot_command_line' has a fix length.
So use strlcpy() instead of strcpy() to avoid memory overflow.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:
kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G D W 3.10.0-rc3-64bit #44
IAOQ[0]: kpageflags_read0x128/0x238
IAOQ[1]: kpageflags_read0x12c/0x238
RP(r2): proc_reg_read0xbc/0x130
Backtrace:
[<00000000402ca2d4>] proc_reg_read0xbc/0x130
[<0000000040235bcc>] vfs_read0xc4/0x1d0
[<0000000040235f0c>] SyS_read0x94/0xf0
[<0000000040105fc0>] syscall_exit0x0/0x14
kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
'path.bc[i]' can be asigned by PCI_SLOT() which can '> 10', so sizeof(6
* "%u:" + "%u" + '\0') may be 21.
Since 'name' length is 20, it may be memory overflow.
And 'path.bc[i]' is 'unsigned char' for printing, we can be sure the
max length of 'name' must be less than 28.
So simplify thinking, we can use 28 instead of 20 directly, and do not
think of whether 'patchc.bc[i]' can '> 100'.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few more fixes for powerpc 3.10. It's a bit more than I
would have liked this late in the game but I suppose that's what
happens with a brand new chip generation coming out.
A few regression fixes, some last minute fixes for new P8 features
such as transactional memory,...
There's also one powerpc KVM patch that I requested that adds two
missing functions to our in-kernel interrupt controller support which
is itself a new 3.10 feature. These are defined by the base
hypervisor specification. We didn't implement them originally because
Linux doesn't use them but they are simple and I'm not comfortable
having a half-implemented interface in 3.10 and having to deal with
versionning etc... later when something starts needing those calls.
They cannot be emulated in qemu when using in-kernel interrupt
controller (not enough shared state).
Just added a last minute patch to fix a typo introducing a breakage in
our cputable for Power7+ processors, sorry about that, but the
regression it fixes just hurt me :-)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
powerpc/kvm/book3s: Add support for H_IPOLL and H_XIRR_X in XICS emulation
powerpc/32bit:Store temporary result in r0 instead of r8
powerpc/mm: Always invalidate tlb on hpte invalidate and update
powerpc/pseries: Improve stream generation comments in copypage/user
powerpc/pseries: Kill all prefetch streams on context switch
powerpc/cputable: Fix oprofile_cpu_type on power8
powerpc/mpic: Fix irq distribution problem when MPIC_SINGLE_DEST_CPU
powerpc/tm: Fix userspace stack corruption on signal delivery for active transactions
powerpc/tm: Move TM abort cause codes to uapi
powerpc/tm: Abort on emulation and alignment faults
powerpc/tm: Update cause codes documentation
powerpc/tm: Make room for hypervisor in abort cause codes
|
|
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
|
|
Pull clock subsystem fixes from Mike Turquette:
"A mix of small fixes affecting mostly ARM platforms as well as a
discrete clock expander chip. Most fixes are corrections to lousy
clock data of one form or another."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: Include clk mxs header file
clk: vt8500: Fix unbalanced spinlock in vt8500_dclk_set_rate()
clk: si5351: Set initial clkout rate when defined in platform data.
clk: si5351: Fix clkout rate computation.
clk: samsung: Add CLK_IGNORE_UNUSED flag for the sysreg clocks
clk: ux500: clk-sysctrl: handle clocks with no parents
clk: ux500: Provide device enumeration number suffix for SMSC911x
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/plagnioj/linux-fbdev
Pull fbdev fixes from Jean-Christophe PLAGNIOL-VILLARD:
"This contains some small fixes
- Atmel LCDC: fix blank the backlight on remove
- ps3fb: fix compile warning
- OMAPDSS: Fix crash with DT boot"
* tag 'fbdev-for-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/plagnioj/linux-fbdev:
atmel_lcdfb: blank the backlight on remove
trivial: atmel_lcdfb: add missing error message
OMAPDSS: Fix crash with DT boot
fbdev/ps3fb: fix compile warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull assorted fixes from Al Viro:
"There'll be more - I'm trying to dig out from under the pile of mail
(a couple of weeks of something flu-like ;-/) and there's several more
things waiting for review; this is just the obvious stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
zoran: racy refcount handling in vm_ops ->open()/->close()
befs_readdir(): do not increment ->f_pos if filldir tells us to stop
hpfs: deadlock and race in directory lseek()
qnx6: qnx6_readdir() has a braino in pos calculation
fix buffer leak after "scsi: saner replacements for ->proc_info()"
vfs: Fix invalid ida_remove() call
|
|
Pull two NFS client fixes from Trond Myklebust:
- Fix a regression that broke NFS mounting using klibc and busybox
- Stable fix to check access modes correctly on NFSv4 delegated open()
* tag 'nfs-for-3.10-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix security flavor negotiation with legacy binary mounts
NFSv4: Fix a thinko in nfs4_try_open_cached
|
|
Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 8f61aa3 "Add support for SIER" missed updates to siar_valid()
and perf_get_data_addr().
In both cases we need to check the SIER instead of mmcra.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This is a revert and then some of commit 860aad7 "Add regs_no_sipr()".
This workaround was only needed on early chip versions.
As before NO_SIPR becomes a static flag of the PMU struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The codes which ever used these two variables have gone. Throw away
them too.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These comments already don't apply to the current code. So just remove
them.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:
CC arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.
Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.
Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X. H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state. H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor. Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.
These hcalls are not currently used by Linux guests, but may be in
future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit a9c4e541ea9b22944da356f2a9258b4eddcc953b
"powerpc/kprobe: Complete kprobe and migrate exception frame"
introduced a regression:
While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.
Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.
As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.
So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CC: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If a hash bucket gets full, we "evict" a more/less random entry from it.
When we do that we don't invalidate the TLB (hpte_remove) because we assume
the old translation is still technically "valid". This implies that when
we are invalidating or updating pte, even if HPTE entry is not valid
we should do a tlb invalidate.
This was a regression introduced by b1022fbd293564de91596b8775340cf41ad5214c
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
No code changes, just documenting what's happening a little better.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On context switch, we should have no prefetch streams leak from one
userspace process to another. This frees up prefetch resources for the
next process.
Based on patch from Milton Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Maynard informed me that neither the oprofile kernel module nor oprofile
userspace has been updated to support that "legacy" oprofile module
interface for power8, which is indicated by "ppc64/power8." This results
in no samples. The solution is to default to the "timer" type, instead.
The raw entry also should be updated, as "ppc64/ibm-compat-v1" indicates
to oprofile userspace to use "compatibility events" which are obsolete
in ISA 2.07.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For the mpic with a flag MPIC_SINGLE_DEST_CPU, only one bit should be
set in interrupt destination registers.
The code is applicable to 64-bit platforms as well as 32-bit.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
transactions
When in an active transaction that takes a signal, we need to be careful with
the stack. It's possible that the stack has moved back up after the tbegin.
The obvious case here is when the tbegin is called inside a function that
returns before a tend. In this case, the stack is part of the checkpointed
transactional memory state. If we write over this non transactionally or in
suspend, we are in trouble because if we get a tm abort, the program counter
and stack pointer will be back at the tbegin but our in memory stack won't be
valid anymore.
To avoid this, when taking a signal in an active transaction, we need to use
the stack pointer from the checkpointed state, rather than the speculated
state. This ensures that the signal context (written tm suspended) will be
written below the stack required for the rollback. The transaction is aborted
becuase of the treclaim, so any memory written between the tbegin and the
signal will be rolled back anyway.
For signals taken in non-TM or suspended mode, we use the
normal/non-checkpointed stack pointer.
Tested with 64 and 32 bit signals
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
These cause codes are usable by userspace, so let's export to uapi.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we are emulating an instruction inside an active user transaction that
touches memory, the kernel can't emulate it as it operates in transactional
suspend context. We need to abort these transactions and send them back to
userspace for the hardware to rollback.
We can service these if the user transaction is in suspend mode, since the
kernel will operate in the same suspend context.
This adds a check to all alignment faults and to specific instruction
emulations (only string instructions for now). If the user process is in an
active (non-suspended) transaction, we abort the transaction go back to
userspace allowing the HW to roll back the transaction and tell the user of the
failure. This also adds new tm abort cause codes to report the reason of the
persistent error to the user.
Crappy test case here http://neuling.org/devel/junkcode/aligntm.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9 only
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
PAPR carves out 0xff-0xe0 for hypervisor use of transactional memory software
abort cause codes. Unfortunately we don't respect this currently.
Below fixes this to move our cause codes to below this region.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9 only
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull reiserfs fixes from Jan Kara:
"Three reiserfs fixes. They fix real problems spotted by users so I
hope they are ok even at this stage."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix deadlock with nfs racing on create/lookup
reiserfs: fix problems with chowning setuid file w/ xattrs
reiserfs: fix spurious multiple-fill in reiserfs_readdir_dentry
|
|
Pull xfs extended attribute fixes for CRCs from Ben Myers:
"Here are several fixes that are relevant on CRC enabled XFS
filesystems. They are followed by a rework of the remote attribute
code so that each block of the attribute contains a header with a CRC.
Previously there was a CRC header per extent in the remote attribute
code, but this was untenable because it was not possible to know how
many extents would be allocated for the attribute until after the
allocation has completed, due to the fragmentation of free space.
This became complicated because the size of the headers needs to be
added to the length of the payload to get the overall length required
for the allocation. With a header per block, things are less
complicated at the cost of a little space.
I would have preferred to defer this and the rest of the CRC queue to
3.11 to mitigate risk for existing non-crc users in 3.10. Doing so
would require setting a feature bit for the on-disk changes, and so I
have been pressured into sending this pull request by Eric Sandeen and
David Chinner from Red Hat. I'll send another pull request or two
with the rest of the CRC queue next week.
- Remove assert on count of remote attribute CRC headers
- Fix the number of blocks read in for remote attributes
- Zero remote attribute tails properly
- Fix mapping of remote attribute buffers to have correct length
- initialize temp leaf properly in xfs_attr3_leaf_unbalance, and
xfs_attr3_leaf_compact
- Rework remote atttributes to have a header per block"
* tag 'for-linus-v3.10-rc4-crc-xattr-fixes' of git://oss.sgi.com/xfs/xfs:
xfs: rework remote attr CRCs
xfs: fully initialise temp leaf in xfs_attr3_leaf_compact
xfs: fully initialise temp leaf in xfs_attr3_leaf_unbalance
xfs: correctly map remote attr buffers during removal
xfs: remote attribute tail zeroing does too much
xfs: remote attribute read too short
xfs: remote attribute allocation may be contiguous
|
|
Pull xfs fixes from Ben Myers:
- Fix nested transactions in xfs_qm_scall_setqlim
- Clear suid/sgid bits when we truncate with size update
- Fix recovery for split buffers
- Fix block count on remote symlinks
- Add fsgeom flag for v5 superblock support
- Disable XFS_IOC_SWAPEXT for CRC enabled filesystems
- Fix dirv3 freespace block corruption
* tag 'for-linus-v3.10-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: fix dir3 freespace block corruption
xfs: disable swap extents ioctl on CRC enabled filesystems
xfs: add fsgeom flag for v5 superblock support.
xfs: fix incorrect remote symlink block count
xfs: fix split buffer vector log recovery support
xfs: kill suid/sgid through the truncate path.
xfs: avoid nesting transactions in xfs_qm_scall_setqlim()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull aer error logging fix from Tony Luck:
"Can't call pci_get_domain_bus_and_slot() from interupt context"
* tag 'please-pull-aertracefix' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
aerdrv: Move cper_print_aer() call out of interrupt context
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Module compilation issues (symbol not exported).
- Plug a hole where user space can bring the kernel down.
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: don't kill the kernel on a bad esr from el0
arm64: treat unhandled compat el0 traps as undef
arm64: Do not report user faults for handled signals
arm64: kernel: compiling issue, need 'EXPORT_SYMBOL(clear_page)'
|
|
Reiserfs is currently able to be deadlocked by having two NFS clients
where one has removed and recreated a file and another is accessing the
file with an open file handle.
If one client deletes and recreates a file with timing such that the
recreated file obtains the same [dirid, objectid] pair as the original
file while another client accesses the file via file handle, the create
and lookup can race and deadlock if the lookup manages to create the
in-memory inode first.
The create thread, in insert_inode_locked4, will hold the write lock
while waiting on the other inode to be unlocked. The lookup thread,
anywhere in the iget path, will release and reacquire the write lock while
it schedules. If it needs to reacquire the lock while the create thread
has it, it will never be able to make forward progress because it needs
to reacquire the lock before ultimately unlocking the inode.
This patch drops the write lock across the insert_inode_locked4 call so
that the ordering of inode_wait -> write lock is retained. Since this
would have been the case before the BKL push-down, this is safe.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
reiserfs_chown_xattrs() takes the iattr struct passed into ->setattr
and uses it to iterate over all the attrs associated with a file to change
ownership of xattrs (and transfer quota associated with the xattr files).
When the setuid bit is cleared during chown, ATTR_MODE and iattr->ia_mode
are passed to all the xattrs as well. This means that the xattr directory
will have S_IFREG added to its mode bits.
This has been prevented in practice by a missing IS_PRIVATE check
in reiserfs_acl_chmod, which caused a double-lock to occur while holding
the write lock. Since the file system was completely locked up, the
writeout of the corrupted mode never happened.
This patch temporarily clears everything but ATTR_UID|ATTR_GID for the
calls to reiserfs_setattr and adds the missing IS_PRIVATE check.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
After sleeping for filldir(), we check to see if the file system has
changed and research. The next_pos pointer is updated but its value
isn't pushed into the key used for the search itself. As a result,
the search returns the same item that the last cycle of the loop did
and filldir() is called multiple times with the same data.
The end result is that the buffer can contain the same name multiple
times. This can be returned to userspace or used internally in the
xattr code where it can manifest with the following warning:
jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2)
reiserfs_for_each_xattr uses reiserfs_readdir_dentry to iterate over
the xattr names and ends up trying to unlink the same name twice. The
second attempt fails with -ENOENT and the error is returned. At some
point I'll need to add support into reiserfsck to remove the orphaned
directories left behind when this occurs.
The fix is to push the value into the key before researching.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
When removing atmel_lcdfb module, the backlight is unregistered but not
blanked. (only for CONFIG_BACKLIGHT_ATMEL_LCDC case).
This can result in the screen going full white depending on how the PWM
is wired.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
When a too small framebuffer is given, the atmel_lcdfb_check_var
silently fails.
Adding an error message will save some head scratching.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
For one thing, there's an ABBA deadlock on hpfs fs-wide lock and i_mutex
in hpfs_dir_lseek() - there's a lot of methods that grab the former with
the caller already holding the latter, so it must take i_mutex first.
For another, locking the damn thing, carefully validating the offset,
then dropping locks and assigning the offset is obviously racy.
Moreover, we _must_ do hpfs_add_pos(), or the machinery in dnode.c
won't modify the sucker on B-tree surgeries.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
