| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of ARC changes from Vineet Gupta:
- Support for Perf from Mischa
- Enabling GPIO/Pinctrl drivers for Abilis TB10x platform
- New defconfig for buildroot
* tag 'arc-v3.13-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-arcfpga] Add defconfig without initramfs location
ARC: perf: ARC 700 PMU doesn't support sampling events
ARC: Add documentation on DT binding for ARC700 PMU
ARC: Add perf support for ARC700 cores
ARC: [TB10x] Updates for GPIO and pinctrl
|
|
Pull watchdog changes from Wim Van Sebroeck:
- addition of MOXA ART watchdog driver (moxart_wdt)
- addition of CSR SiRFprimaII and SiRFatlasVI watchdog driver
(sirfsoc_wdt)
- addition of ralink watchdog driver (rt2880_wdt)
- various fixes and cleanups (__user annotation, ioctl return codes,
removal of redundant of_match_ptr, removal of unnecessary
amba_set_drvdata(), use allocated buffer for usb_control_msg, ...)
- removal of MODULE_ALIAS_MISCDEV statements
- watchdog related DT bindings
- first set of improvements on the w83627hf_wdt driver
* git://www.linux-watchdog.org/linux-watchdog: (26 commits)
watchdog: w83627hf: Use helper functions to access superio registers
watchdog: w83627hf: Enable watchdog device only if not already enabled
watchdog: w83627hf: Enable watchdog only once
watchdog: w83627hf: Convert to watchdog infrastructure
watchdog: omap_wdt: raw read and write endian fix
watchdog: sirf: don't depend on dummy value of CLOCK_TICK_RATE
watchdog: pcwd_usb: overflow in usb_pcwd_send_command()
watchdog: rt2880_wdt: fix return value check in rt288x_wdt_probe()
watchdog: watchdog_core: Fix a trivial typo
watchdog: dw: Enable OF support for DW watchdog timer
watchdog: Get rid of MODULE_ALIAS_MISCDEV statements
watchdog: ts72xx_wdt: Propagate return value from timeout_to_regval
watchdog: pcwd_usb: Use allocated buffer for usb_control_msg
watchdog: sp805_wdt: Remove unnecessary amba_set_drvdata()
watchdog: sirf: add watchdog driver of CSR SiRFprimaII and SiRFatlasVI
watchdog: Remove redundant of_match_ptr
watchdog: ts72xx_wdt: cleanup return codes in ioctl
documentation/devicetree: Move DT bindings from gpio to watchdog
watchdog: add ralink watchdog driver
watchdog: Add MOXA ART watchdog driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
|
|
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
|
|
Pull EDAC updates from Borislav Petkov:
"Following up on last week's discussion, here's my part of the EDAC
pile, highlights in the signed tag.
The last two patches have a date from just now because I've just
applied them to the tree after Johannes sent them to me earlier. I
decided to forward them now because they're trivial.
There's a third one for MPC85xx which adds PCIe error interrupt
support but since it is not so trivial and hasn't seen any linux-next
time, I'm deferring it to 3.14
EDAC update highlights:
- Support for Calxeda ECX-2000 memory controller, from Robert Richter
- Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob
Herring and Robert Richter
- New maintainer for Freescale's MPC85xx EDAC driver: Johannes
Thumshirn"
* tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
edac/85xx: Remove mpc85xx_pci_err_remove
EDAC: Add edac-mpc85xx driver to MAINTAINERS
edac, highbank: Moving error injection to sysfs for edac
edac, highbank: Add MAINTAINERS entry
edac: Unify reporting of device info for device, mc and pci
edac, highbank: Improve and unify naming
edac, highbank: Add Calxeda ECX-2000 support
ARM: dts: calxeda: move memory-controller node out of ecx-common.dtsi
edac, highbank: Fix interrupt setup of mem and l2 controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
|
|
Add device tree support to the DW watchdog timer.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
|
|
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
I accidently put the devicetree bindings for the MEN A21 watchdog driver in
Documentation/devicetree/bindings/gpio instead of
Documentation/devicetree/bindings/watchdog, this patch addresses this error.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Rob Landley <rob@landley.net>
|
|
Add a driver for the watchdog timer found on Ralink SoC
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
|
|
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- i2c-hid is not querying init reports any more, as it's not mandated
by the spec, and annoys quite a few devices during enumeration, by
Bibek Basu
- a lot of fixes for Logitech devices, by Simon Wood
- hid-apple now has an option to switch between Option and Command
mode, by Nanno Langstraat
- Some more workarounds for severely broken ELO devices, by Oliver
Neukum
- more devm conversions, by Benjamin Tissoires
- wiimote correctness fixes, by David Herrmann
- a lot of added support for various new device IDs and random small
fixes here and there"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: enable Mayflash USB Gamecube Adapter
HID: sony: Add force feedback support for Dualshock3 USB
Input: usbtouchscreen: ignore eGalax/D-Wav/EETI HIDs
HID: don't ignore eGalax/D-Wav/EETI HIDs
HID: roccat: add missing special driver declarations
HID:hid-lg4ff: Correct Auto-center strength for wheels other than MOMO and MOMO2
HID:hid-lg4ff: Initialize device properties before we touch autocentering.
HID:hid-lg4ff: ensure ConstantForce is disabled when set to 0
HID:hid-lg4ff: Switch autocentering off when strength is set to zero.
HID:hid-lg4ff: Scale autocentering force properly on Logitech wheel
HID: roccat: fix Coverity CID 141438
HID: multitouch: add manufacturer to Kconfig help text
HID: logitech-dj: small cleanup in rdcat()
HID: remove self-assignment from hid_input_report
HID: hid-sensor-hub: fix report size
HID: i2c-hid: Stop querying for init reports
HID: roccat: add support for Ryos MK keyboards
HID: roccat: generalize some common code
HID: roccat: add new device return value
HID: wiimote: add pro-controller analog stick calibration
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
|
|
'for-3.13/i2c-hid', 'for-3.13/logitech', 'for-3.13/multitouch', 'for-3.13/roccat', 'for-3.13/upstream' and 'for-3.13/wiimote' into for-linus
|
|
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kconfig changes from Michal Marek:
- xconfig stores its setting in a meaningful path
(~/.config/kernel.org/qconf.conf)
- kconfig symbol search fix
- documentation fixes
- cleanup & comment update
- fix warning when a kconfig symbol is defined with two different types
- Yann is now officially listed as maintainer of kconfig, but he
prefers me to send pull requests for now
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
MAINTAINERS: New kconfig maintainer
xconfig: Fix the filename for GUI settings
kconfig: fix bug in search results string: use strlen(gstr->s), not gstr->len
kconfig: remove unused definition from scanner
kconfig: adjust warning message for conflicting types
kconfig: fix trivial typos and update mconf documentation
kconfig: add short explanation to SYMBOL_WRITE
Documentation/kbuild/kconfig.txt: 'make listnewconfig' replaces: yes "" | make oldconfig
|
|
Add documentation for the generic OMAP DES crypto modul describing the device
tree bindings.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
A new compatible property "ti,omap5-sham" is added to the omap-sham driver
recently to support SHA/MD5 for OMAP5,DRA7 and AM43XX. Documenting the
same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add OF document for LM90 in Documentation/devicetree/.
[JD: Add this new file to the LM90 MAINTAINERS entry.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Pull KVM changes from Paolo Bonzini:
"Here are the 3.13 KVM changes. There was a lot of work on the PPC
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a few
bugfixes.
ARM got transparent huge page support, improved overcommit, and
support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes some
nVidia cards on Windows, that fail to start without these patches and
the corresponding userspace changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
kvm, vmx: Fix lazy FPU on nested guest
arm/arm64: KVM: PSCI: propagate caller endianness to the incoming vcpu
arm/arm64: KVM: MMIO support for BE guest
kvm, cpuid: Fix sparse warning
kvm: Delete prototype for non-existent function kvm_check_iopl
kvm: Delete prototype for non-existent function complete_pio
hung_task: add method to reset detector
pvclock: detect watchdog reset at pvclock read
kvm: optimize out smp_mb after srcu_read_unlock
srcu: API for barrier after srcu read unlock
KVM: remove vm mmap method
KVM: IOMMU: hva align mapping page size
KVM: x86: trace cpuid emulation when called from emulator
KVM: emulator: cleanup decode_register_operand() a bit
KVM: emulator: check rex prefix inside decode_register()
KVM: x86: fix emulation of "movzbl %bpl, %eax"
kvm_host: typo fix
KVM: x86: emulate SAHF instruction
MAINTAINERS: add tree for kvm.git
Documentation/kvm: add a 00-INDEX file
...
|
|
If split page table lock is in use, we embed the lock into struct page
of table's page. We have to disable split lock, if spinlock_t is too
big be to be embedded, like when DEBUG_SPINLOCK or DEBUG_LOCK_ALLOC
enabled.
This patch add support for dynamic allocation of split page table lock
if we can't embed it to struct page.
page->ptl is unsigned long now and we use it as spinlock_t if
sizeof(spinlock_t) <= sizeof(long), otherwise it's pointer to spinlock_t.
The spinlock_t allocated in pgtable_page_ctor() for PTE table and in
pgtable_pmd_page_ctor() for PMD table. All other helpers converted to
support dynamically allocated page->ptl.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After commit c9eeec26e32e ("tcp: TSQ can use a dynamic limit"), several
users reported throughput regressions, notably on mvneta and wifi
adapters.
802.11 AMPDU requires a fair amount of queueing to be effective.
This patch partially reverts the change done in tcp_write_xmit()
so that the minimal amount is sysctl_tcp_limit_output_bytes.
It also remove the use of this sysctl while building skb stored
in write queue, as TSO autosizing does the right thing anyway.
Users with well behaving NICS and correct qdisc (like sch_fq),
can then lower the default sysctl_tcp_limit_output_bytes value from
128KB to 8KB.
This new usage of sysctl_tcp_limit_output_bytes permits each driver
authors to check how their driver performs when/if the value is set
to a minimum of 4KB.
Normally, line rate for a single TCP flow should be possible,
but some drivers rely on timers to perform TX completion and
too long TX completion delays prevent reaching full throughput.
Fixes: c9eeec26e32e ("tcp: TSQ can use a dynamic limit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct the SPI node compatible property items to match example code and
match current DTS usage.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.
This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Nothing particularly stands out in this pull request. The biggest
part of the changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix
potential dead lock" which hopefully fixes the fb locking issues
reported by multiple persons.
There are also a few commits that have changes to arch/arm/mach-at91
and arch/avr32, which have been acked by the maintainers"
* tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (143 commits)
fb: reorder the lock sequence to fix potential dead lock
fbdev: shmobile-lcdcfb: Convert to clk_prepare/unprepare
fbdev: shmobile-hdmi: Convert to clk_prepare/unprepare
omapdss: Add new panel driver for Topolly td028ttec1 LCD.
video: exynos_mipi_dsi: Unlock the mutex before returning
video: da8xx-fb: remove unwanted define
video: Remove unnecessary semicolons
simplefb: use write-combined remapping
simplefb: fix unmapping fb during destruction
OMAPDSS: connector-dvi: fix releasing i2c_adapter
OMAPDSS: DSI: fix perf measuring ifdefs
framebuffer: Use fb_<level>
framebuffer: Add fb_<level> convenience logging macros
efifb: prevent null-deref when iterating dmi_list
fbdev: fix error return code in metronomefb_probe()
video: xilinxfb: Fix for "Use standard variable name convention"
OMAPDSS: Fix de_level in videomode_to_omap_video_timings()
video: xilinxfb: Simplify error path
video: xilinxfb: Use devm_kzalloc instead of kzalloc
video: xilinxfb: Use standard variable name convention
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Resource management
- Fix host bridge window coalescing (Alexey Neyman)
- Pass type, width, and prefetchability for window alignment (Wei Yang)
PCI device hotplug
- Convert acpiphp, acpiphp_ibm to dynamic debug (Lan Tianyu)
Power management
- Remove pci_pm_complete() (Liu Chuansheng)
MSI
- Fail initialization if device is not in PCI_D0 (Yijing Wang)
MPS (Max Payload Size)
- Use pcie_get_mps() and pcie_set_mps() to simplify code (Yijing Wang)
- Use pcie_set_readrq() to simplify code (Yijing Wang)
- Use cached pci_dev->pcie_mpss to simplify code (Yijing Wang)
SR-IOV
- Enable upstream bridges even for VFs on virtual buses (Bjorn Helgaas)
- Use pci_is_root_bus() to avoid catching virtual buses (Wei Yang)
Virtualization
- Add x86 MSI masking ops (Konrad Rzeszutek Wilk)
Freescale i.MX6
- Support i.MX6 PCIe controller (Sean Cross)
- Increase link startup timeout (Marek Vasut)
- Probe PCIe in fs_initcall() (Marek Vasut)
- Fix imprecise abort handler (Tim Harvey)
- Remove redundant of_match_ptr (Sachin Kamat)
Renesas R-Car
- Support Gen2 internal PCIe controller (Valentine Barshak)
Samsung Exynos
- Add MSI support (Jingoo Han)
- Turn off power when link fails (Jingoo Han)
- Add Jingoo Han as maintainer (Jingoo Han)
- Add clk_disable_unprepare() on error path (Wei Yongjun)
- Remove redundant of_match_ptr (Sachin Kamat)
Synopsys DesignWare
- Add irq_create_mapping() (Pratyush Anand)
- Add header guards (Seungwon Jeon)
Miscellaneous
- Enable native PCIe services by default on non-ACPI (Andrew Murray)
- Cleanup _OSC usage and messages (Bjorn Helgaas)
- Remove pcibios_last_bus boot option on non-x86 (Bjorn Helgaas)
- Convert bus code to use bus_, drv_, and dev_groups (Greg Kroah-Hartman)
- Remove unused pci_mem_start (Myron Stowe)
- Make sysfs functions static (Sachin Kamat)
- Warn on invalid return from driver probe (Stephen M. Cameron)
- Remove Intel Haswell D3 delays (Todd E Brandt)
- Call pci_set_master() in core if driver doesn't do it (Yinghai Lu)
- Use pci_is_pcie() to simplify code (Yijing Wang)
- Use PCIe capability accessors to simplify code (Yijing Wang)
- Use cached pci_dev->pcie_cap to simplify code (Yijing Wang)
- Removed unused "is_pcie" from struct pci_dev (Yijing Wang)
- Simplify sysfs CPU affinity implementation (Yijing Wang)"
* tag 'pci-v3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (79 commits)
PCI: Enable upstream bridges even for VFs on virtual buses
PCI: Add pci_upstream_bridge()
PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()
PCI: Warn on driver probe return value greater than zero
PCI: Drop warning about drivers that don't use pci_set_master()
PCI: Workaround missing pci_set_master in pci drivers
powerpc/pci: Use pci_is_pcie() to simplify code [fix]
PCI: Update pcie_ports 'auto' behavior for non-ACPI platforms
PCI: imx6: Probe the PCIe in fs_initcall()
PCI: Add R-Car Gen2 internal PCI support
PCI: imx6: Remove redundant of_match_ptr
PCI: Report pci_pme_active() kmalloc failure
mn10300/PCI: Remove useless pcibios_last_bus
frv/PCI: Remove pcibios_last_bus
PCI: imx6: Increase link startup timeout
PCI: exynos: Remove redundant of_match_ptr
PCI: imx6: Fix imprecise abort handler
PCI: Fail MSI/MSI-X initialization if device is not in PCI_D0
PCI: imx6: Remove redundant dev_err() in imx6_pcie_probe()
x86/PCI: Coalesce multiple overlapping host bridge windows
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
"A set of device-mapper changes for 3.13.
Improve reliability of buffer allocations for dm messages with a small
number of arguments, a couple path group initialization fixes for dm
multipath, a fix for resizing a dm array, various fixes and
optimizations for dm cache, a fix for device mapper's Kconfig menu
indentation.
Features added include:
- dm crypt support for activating legacy CBC TrueCrypt containers
(useful for forensics of these old TCRYPT containers)
- reduced dm-cache memory requirements for each block in the cache
- basic support for shrinking a dm-cache's cache (fast) device
- most notably, dm-cache support for managing cache coherency when
deploying dm-cache with sophisticated origin volumes (that support
hardware snapshots and/or clustering): these changes come in the
form of a new passthrough operation mode and a cache block
invalidation interface"
* tag 'dm-3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (32 commits)
dm cache: resolve small nits and improve Documentation
dm cache: add cache block invalidation support
dm cache: add remove_cblock method to policy interface
dm cache policy mq: reduce memory requirements
dm cache metadata: check the metadata version when reading the superblock
dm cache: add passthrough mode
dm cache: cache shrinking support
dm cache: promotion optimisation for writes
dm cache: be much more aggressive about promoting writes to discarded blocks
dm cache policy mq: implement writeback_work() and mq_{set,clear}_dirty()
dm cache: optimize commit_if_needed
dm space map disk: optimise sm_disk_dec_block
MAINTAINERS: add reference to device-mapper's linux-dm.git tree
dm: fix Kconfig menu indentation
dm: allow remove to be deferred
dm table: print error on preresume failure
dm crypt: add TCW IV mode for old CBC TCRYPT containers
dm crypt: properly handle extra key string in initialization
dm cache: log error message if dm_kcopyd_copy() fails
dm cache: use cell_defer() boolean argument consistently
...
|
|
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
|
|
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for 3.13. As with the core pull
request just sent out, this was rebased on top of the core branch
again after the immutable series was pulled. This also means that
bcache gets to sit the initial pull over. I will send a second driver
pull request in the merge window to get those fixes in, once they have
been rebased and tested on top of the non-immutable stack.
This pull request contains:
- Add support for the sTec Kronos pci-e flash card from sTec. Also
has various cleanups for this driver, from myself, Bart, Mike
Snizter, and Wei Yongjun.
- Add surprise removal support for the micron mtip32xx driver from
Micron.
- Floppy documentation fix from Ben Harris.
- debugfs bug fix for pktcdvd from Dan Carpenter.
- Fix for the mtip32xx driver stack usage in the debugfs path,
dynamically allocating those buffers instead. From David Milburn.
- Disable cpqarray in Kconfig. The plan is to remove it on request
of HP, but lets disable it for a few revisions just to see if
anyone yells.
- drbd fixes from Lars Ellenberg and Philipp Reisner.
- Elevator switch fix for the s390 block driver from Heiko Carstens.
- loop crash fix on IO to unassigned device from Mikulas Patocka.
- A series of bug fixes for the IBM rsxx pci-e flash driver from
Philip J Kelleher.
- cciss probe fix from Stephen Cameron.
- Xen block front/back fixes from Roger Pau Monne and Vegard Nossum"
* 'for-3.13/drivers' of git://git.kernel.dk/linux-block: (41 commits)
floppy: Correct documentation of driver options when used as a module.
pktcdvd: debugfs functions return NULL on error
xen-blkfront: restore the non-persistent data path
skd: fix formatting in skd_s1120.h
skd: reorder construct/destruct code
skd: cleanup skd_do_inq_page_da()
skd: remove SKD_OMIT_FROM_SRC_DIST ifdefs
skd: remove redundant skdev->pdev assignment from skd_pci_probe()
skd: use <asm/unaligned.h>
skd: remove SCSI subsystem specific includes
skd: register block device only if some devices are present
skd: fix error messages in skd_init()
skd: fix error paths in skd_init()
skd: fix unregister_blkdev() placement
skd: more removal of bio-based code
skd: cleanup the skd_*() function block wrapping
skd: rip out bio path
skd: fix error return code in skd_pci_probe()
s390/dasd: hold request queue sysfs lock when calling elevator_init()
cciss: return 0 from driver probe function on success, not 1
...
|
|
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
|
|
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
|
|
Merge first patch-bomb from Andrew Morton:
"Quite a lot of other stuff is banked up awaiting further
next->mainline merging, but this batch contains:
- Lots of random misc patches
- OCFS2
- Most of MM
- backlight updates
- lib/ updates
- printk updates
- checkpatch updates
- epoll tweaking
- rtc updates
- hfs
- hfsplus
- documentation
- procfs
- update gcov to gcc-4.7 format
- IPC"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (269 commits)
ipc, msg: fix message length check for negative values
ipc/util.c: remove unnecessary work pending test
devpts: plug the memory leak in kill_sb
./Makefile: export initial ramdisk compression config option
init/Kconfig: add option to disable kernel compression
drivers: w1: make w1_slave::flags long to avoid memory corruption
drivers/w1/masters/ds1wm.cuse dev_get_platdata()
drivers/memstick/core/ms_block.c: fix unreachable state in h_msb_read_page()
drivers/memstick/core/mspro_block.c: fix attributes array allocation
drivers/pps/clients/pps-gpio.c: remove redundant of_match_ptr
kernel/panic.c: reduce 1 byte usage for print tainted buffer
gcov: reuse kbasename helper
kernel/gcov/fs.c: use pr_warn()
kernel/module.c: use pr_foo()
gcov: compile specific gcov implementation based on gcc version
gcov: add support for gcc 4.7 gcov format
gcov: move gcov structs definitions to a gcc version specific file
kernel/taskstats.c: return -ENOMEM when alloc memory fails in add_del_listener()
kernel/taskstats.c: add nla_nest_cancel() for failure processing between nla_nest_start() and nla_nest_end()
kernel/sysctl_binary.c: use scnprintf() instead of snprintf()
...
|
|
This allows the charger to be enabled with devicetree, and allows the
parameters for charging the backup battery to be set.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
"This adds a ->writepage() implementation to fuse, improving mmaped
writeout and paving the way for buffered writeback.
And there's a patch to add a fix minor number for /dev/cuse, similarly
to /dev/fuse"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: writepages: protect secondary requests from fuse file release
fuse: writepages: update bdi writeout when deleting secondary request
fuse: writepages: crop secondary requests
fuse: writepages: roll back changes if request not found
cuse: add fix minor number to /dev/cuse
fuse: writepage: skip already in flight
fuse: writepages: handle same page rewrites
fuse: writepages: fix aggregation
fuse: fix race in fuse_writepages()
fuse: Implement writepages callback
fuse: don't BUG on no write file
fuse: lock page in mkwrite
fuse: Prepare to handle multiple pages in writeback
fuse: Getting file for writeback helper
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches.
- add a sysfs to control reclaiming free segments
- enhance the f2fs global lock procedures
- enhance the victim selection flow
- wait for selected node blocks during fsync
- add some tracepoints
- add a config to remove abundant BUG_ONs
The other bug fixes are as follows.
- fix deadlock on acl operations
- fix some bugs with respect to orphan inodes
And, there are a bunch of cleanups"
* tag 'for-f2fs-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (42 commits)
f2fs: issue more large discard command
f2fs: fix memory leak after kobject init failed in fill_super
f2fs: cleanup waiting routine for writeback pages in cp
f2fs: avoid to use a NULL point in destroy_segment_manager
f2fs: remove unnecessary TestClearPageError when wait pages writeback
f2fs: update f2fs document
f2fs: avoid to wait all the node blocks during fsync
f2fs: check all ones or zeros bitmap with bitops for better mount performance
f2fs: change the method of calculating the number summary blocks
f2fs: fix calculating incorrect free size when update xattr in __f2fs_setxattr
f2fs: add an option to avoid unnecessary BUG_ONs
f2fs: introduce CONFIG_F2FS_CHECK_FS for BUG_ON control
f2fs: fix a deadlock during init_acl procedure
f2fs: clean up acl flow for better readability
f2fs: remove unnecessary segment bitmap updates
f2fs: add tracepoint for vm_page_mkwrite
f2fs: add tracepoint for set_page_dirty
f2fs: remove redundant set_page_dirty from write_compacted_summaries
f2fs: add reclaiming control by sysfs
f2fs: introduce f2fs_balance_fs_bg for some background jobs
...
|
