aboutsummaryrefslogtreecommitdiff
path: root/Documentation
AgeCommit message (Collapse)Author
2015-12-12Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Arnd Bergmann: "Here are a bunch of small bug fixes for various ARM platforms, nothing really sticks out this week, most of either fixes bugs in code that was just added in 4.4, or that has been broken for many years without anyone noticing. at91/sama5d2: - fix sama5de hardware setup of sd/mmc interface - proper selection of pinctrl drivers. PIO4 is necessary for sama5d2 berlin: - fix incorrect clock input for SDIO exynos: - Fix potential NULL pointer dereference in Exynos PMU driver. imx: - Fix vf610 SAI clock configuration bug which is discovered by the newly added master mode support in SAI audio driver. - Fix buggy L2 cache latency values in vf610 device trees, which may cause system hang when cpu runs at a higher frequency. ixp4xx: - fix prototypes for readl/writel functions ls2080a: - use little-endian register access for GPIO and SDHCI omap: - Fix clock source for ARM TWD and global timers on am437x - Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when MACH_OMAP3_PANDORA is selected - Fix SPI DMA handles for dm816x as only some were mapped - Fix up mbox cells for dm816x to make mailbox usable pxa: - use PWM lookup table for all ezx machines s3c24xx: - Remove incorrect __init annotation from s3c24xx cpufreq driver structures. versatile: - fix PCI IRQ mapping on Versatile PB" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ls2080a/dts: Add little endian property for GPIO IP block dt-bindings: define little-endian property for QorIQ GPIO ARM64: dts: ls2080a: fix eSDHC endianness ARM: dts: vf610: use reset values for L2 cache latencies ARM: pxa: use PWM lookup table for all machines ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1 ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock ARM: dts: am4372: fix clock source for arm twd and global timers ARM: at91: fix pinctrl driver selection ARM: at91/dt: add always-on to 1.8V regulator ARM: dts: vf610: fix clock definition for SAI2 ARM: imx: clk-vf610: fix SAI clock tree ARM: ixp4xx: fix read{b,w,l} return types irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE ARM: dts: add dm816x missing spi DT dma handles ARM: dts: add dm816x missing #mbox-cells cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
2015-12-11dt-bindings: define little-endian property for QorIQ GPIOLi Yang
The GPIO block on different QorIQ chips could have registers in different endianess. Define the property to specify which endian is used by the hardware. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
2015-12-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: "A lot of Thanksgiving turkey leftovers accumulated, here goes: 1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg. 2) IDs for some new iwlwifi chips, from Oren Givon. 3) Fix rtlwifi lockups on boot, from Larry Finger. 4) Fix memory leak in fm10k, from Stephen Hemminger. 5) We have a route leak in the ipv6 tunnel infrastructure, fix from Paolo Abeni. 6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim. 7) Wrong lockdep annotations in tcp md5 support, fix from Eric Dumazet. 8) Work around some middle boxes which prevent proper handling of TCP Fast Open, from Yuchung Cheng. 9) TCP repair can do huge kmalloc() requests, build paged SKBs instead. From Eric Dumazet. 10) Fix msg_controllen overflow in scm_detach_fds, from Daniel Borkmann. 11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from Nikolay Aleksandrov. 12) Fix use after free in epoll with AF_UNIX sockets, from Rainer Weikusat. 13) Fix double free in VRF code, from Nikolay Aleksandrov. 14) Fix skb leaks on socket receive queue in tipc, from Ying Xue. 15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian. 16) Fix clearing of persistent array maps in bpf, from Daniel Borkmann. 17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq early enough. From Eric Dumazet. 18) Fix out of bounds accesses in bpf array implementation when updating elements, from Daniel Borkmann. 19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric Dumazet. 20) When dumping proxy neigh entries, we have to accomodate NULL device pointers properly, from Konstantin Khlebnikov. 21) SCTP doesn't release all ipv6 socket resources properly, fix from Eric Dumazet. 22) Prevent underflows of sch->q.qlen for multiqueue packet schedulers, also from Eric Dumazet. 23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey Huang and Michael Chan. 24) Don't actively scan radar channels, from Antonio Quartulli" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits) net: phy: reset only targeted phy bnxt_en: Setup uc_list mac filters after resetting the chip. bnxt_en: enforce proper storing of MAC address bnxt_en: Fixed incorrect implementation of ndo_set_mac_address net: lpc_eth: remove irq > NR_IRQS check from probe() net_sched: fix qdisc_tree_decrease_qlen() races openvswitch: fix hangup on vxlan/gre/geneve device deletion ipv4: igmp: Allow removing groups from a removed interface ipv6: sctp: implement sctp_v6_destroy_sock() arm64: bpf: add 'store immediate' instruction ipv6: kill sk_dst_lock ipv6: sctp: add rcu protection around np->opt net/neighbour: fix crash at dumping device-agnostic proxy entries sctp: use GFP_USER for user-controlled kmalloc sctp: convert sack_needed and sack_generation to bits ipv6: add complete rcu protection around np->opt bpf: fix allocation warnings in bpf maps and integer overflow mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0 net: mvneta: enable setting custom TX IP checksum limit net: mvneta: fix error path for building skb ...
2015-12-02net: mvneta: enable setting custom TX IP checksum limitMarcin Wojtas
Since Armada 38x SoC can support IP checksum for jumbo frames only on a single port, it means that this feature should be enabled per-port, rather than for the whole SoC. This patch enables setting custom TX IP checksum limit by adding new optional property to the mvneta device tree node. If not used, by default 1600B is set for "marvell,armada-370-neta" and 9800B for other strings, which ensures backward compatibility. Binding documentation is updated accordingly. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-29Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux Pull thermal management fixes from Zhang Rui: "Specifics: - several fixes and cleanups on Rockchip thermal drivers. - add the missing support of RK3368 SoCs in Rockchip driver. - small fixes on of-thermal, power_allocator, rcar driver, IMX, and QCOM drivers, and also compilation fixes, on thermal.h, when thermal is not selected" * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: imx: thermal: use CPU temperature grade info for thresholds thermal: fix thermal_zone_bind_cooling_device prototype Revert "thermal: qcom_spmi: allow compile test" thermal: rcar_thermal: remove redundant operation thermal: of-thermal: Reduce log level for message when can't fine thermal zone thermal: power_allocator: Use temperature reading from tz thermal: rockchip: Support the RK3368 SoCs in thermal driver thermal: rockchip: consistently use int for temperatures thermal: rockchip: Add the sort mode for adc value increment or decrement thermal: rockchip: improve the conversion function thermal: rockchip: trivial: fix typo in commit thermal: rockchip: better to compatible the driver for different SoCs dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
2015-11-27Merge tag 'fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Arnd Bergmann: "There is a small backlog of at91 patches here, the most significant is the addition of some sama5d2 Xplained nodes that were waiting on an MFD include file to get merged through another tree. We normally try to sort those out before the merge window opens, but the maintainer wasn't aware of that here and I decided to merge the changes this time as an exception. On OMAP a series of audio changes for dra7 missed the merge window but turned out to be necessary to fix a boot time imprecise external abort error and to get audio working. The other changes are the usual simple changes, here is a list sorted by platform: at91: removal of a useless defconfig option removal of some legacy DT pieces use of the proper watchdog compatible string update of the MAINTAINERS entries for some Atmel drivers drivers/scpi: hide get_scpi_ops in module from built-in code imx: add missing .irq_set_type for i.MX GPC irq_chip. fix the wrong spi-num-chipselects settings for Vybrid DSPI devices. fix a merge error in Vybrid dts regarding to ADC device property keystone: fix the optional PDSP firmware loading fix linking RAM setup for QMs fix crash with clk_ignore_unused mediatek: Enable SCPSYS power domain driver by default mvebu: fix QNAP TS219 power-off in dts fix legacy get_irqnr_and_base for dove and orion5x omap: fix l4 related boot time errors for dm81xx use lockless cldm/pwrdm api in omap4_boot_secondary remove t410 abort handler to avoid hiding other critical errors mark cpuidle tracepoints as _rcuidle fix module alias for omap-ocp2scp pxa: palm: Fix typos in PWM lookup table code renesas: missing __initconst annotation for r8a7793_boards_compat_dt rockchip: disable mmc-tuning on the veyron-minnie board adding the init state for the over-temperature-protection zx: only build power domain code when CONFIG_PM=y" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits) ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data ARM: orion5x: Fix legacy get_irqnr_and_base ARM: dove: Fix legacy get_irqnr_and_base soc: Mediatek: Enable SCPSYS power domain driver by default ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects. ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers soc: ti: use request_firmware_direct() as acc firmware is optional ARM: imx: add platform irq type setting in gpc ARM: dts: vfxxx: Fix erroneous property in esdhc0 node ARM: shmobile: r8a7793: proper constness with __initconst scpi: hide get_scpi_ops in module from built-in code ARM: zx: only build power domain code when CONFIG_PM=y ARM: pxa: palm: Fix typos in PWM lookup table code ARM: dts: Kirkwood: Fix QNAP TS219 power-off ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie MAINTAINERS: Atmel drivers: change NAND and ISI entries ARM: at91/dt: sama5d2 Xplained: add several devices ...
2015-11-24Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block layer fixes from Jens Axboe: "A round of fixes/updates for the current series. This looks a little bigger than it is, but that's mainly because we pushed the lightnvm enabled null_blk change out of the merge window so it could be updated a bit. The rest of the volume is also mostly lightnvm. In particular: - Lightnvm. Various fixes, additions, updates from Matias and Javier, as well as from Wenwei Tao. - NVMe: - Fix for potential arithmetic overflow from Keith. - Also from Keith, ensure that we reap pending completions from a completion queue before deleting it. Fixes kernel crashes when resetting a device with IO pending. - Various little lightnvm related tweaks from Matias. - Fixup flushes to go through the IO scheduler, for the cases where a flush is not required. Fixes a case in CFQ where we would be idling and not see this request, hence not break the idling. From Jan Kara. - Use list_{first,prev,next} in elevator.c for cleaner code. From Gelian Tang. - Fix for a warning trigger on btrfs and raid on single queue blk-mq devices, where we would flush plug callbacks with preemption disabled. From me. - A mac partition validation fix from Kees Cook. - Two merge fixes from Ming, marked stable. A third part is adding a new warning so we'll notice this quicker in the future, if we screw up the accounting. - Cleanup of thread name/creation in mtip32xx from Rasmus Villemoes" * 'for-linus' of git://git.kernel.dk/linux-block: (32 commits) blk-merge: warn if figured out segment number is bigger than nr_phys_segments blk-merge: fix blk_bio_segment_split block: fix segment split blk-mq: fix calling unplug callbacks with preempt disabled mac: validate mac_partition is within sector mtip32xx: use formatting capability of kthread_create_on_node NVMe: reap completion entries when deleting queue lightnvm: add free and bad lun info to show luns lightnvm: keep track of block counts nvme: lightnvm: use admin queues for admin cmds lightnvm: missing free on init error lightnvm: wrong return value and redundant free null_blk: do not del gendisk with lightnvm null_blk: use device addressing mode null_blk: use ppa_cache pool NVMe: Fix possible arithmetic overflow for max segments blk-flush: Queue through IO scheduler when flush not required null_blk: register as a LightNVM device elevator: use list_{first,prev,next}_entry lightnvm: cleanup queue before target removal ...
2015-11-23ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in ↵Murali Karicheri
bootargs Currently kernel crash randomly when K2L EVM is booted without clk_ignore_unused in the bootargs. This workaround is not needed on other K2 devices such as K2HK and K2E and with this fix, we can remove the workaround altogether. netcp driver on K2L uses linked ram on OSR (On chip Static RAM) and requires the clock to this peripheral enabled for proper functioning. This is the reason for the kernel crash. So add the clock node to fix this issue. While at it, remove the workaround documentation as well. With the fix applied, clk_summary dump shows the clock to OSR enabled. cat /sys/kernel/debug/clk/clk_summary ------cut-------------- tcp3d-1 0 0 399360000 0 0 tcp3d-0 0 0 399360000 0 0 osr 1 1 399360000 0 0 fftc-0 0 0 399360000 0 0 -----cut---------------- Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2015-11-20Merge branch 'i2c/for-current' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "A few bugfixes and one PCI ID addition from I2C" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: i801: add Intel Lewisburg device IDs i2c: fix wakeup irq parsing i2c: xiic: Prevent concurrent running of the IRQ handler and __xiic_start_xfer() i2c: Revert "i2c: xiic: Do not reset controller before every transfer" i2c: imx: fix a compiling error
2015-11-20Merge tag 'pm+acpi-4.4-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management and ACPI updates from Rafael Wysocki: "These are mostly fixes and cleanups (ACPI core, PM core, cpufreq, ACPI EC driver, device properties) including three reverts of recent intel_pstate driver commits due to a regression introduced by one of them plus support for Atom Airmont cores in intel_pstate (which really boils down to adding new frequency tables for Airmont) and additional turbostat updates. Specifics: - Revert three recent intel_pstate driver commits one of which introduced a regression and the remaining two depend on the problematic one (Rafael Wysocki). - Fix breakage related to the recently introduced ACPI _CCA object support in the PCI DMA setup code (Suravee Suthikulpanit). - Fix up the recently introduced ACPI CPPC support to only use the hardware-reduced version of the PCCT structure as the only architecture to support it (ARM64) will only use hardware-reduced ACPI anyway (Ashwin Chaugule). - Fix a cpufreq mediatek driver build problem (Arnd Bergmann). - Fix the SMBus transaction handling implementation in the ACPI core to avoid re-entrant calls to wait_event_timeout() which makes intermittent boot stalls related to the Smart Battery Subsystem initialization go away and revert a workaround of another problem with the same underlying root cause (Chris Bainbridge). - Fix the generic wakeup interrupts framework to avoid using invalid IRQ numbers (Dmitry Torokhov). - Remove a redundant check from the ACPI EC driver (Markus Elfring). - Modify the intel_pstate driver so it can support more Atom flavors than just one (Baytrail) and add support for Atom Airmont cores (which require new freqnency tables) to it (Philippe Longepe). - Clean up MSR-related symbols in turbostat (Len Brown)" * tag 'pm+acpi-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PCI: Fix OF logic in pci_dma_configure() Revert "Documentation: kernel_parameters for Intel P state driver" cpufreq: mediatek: fix build error cpufreq: intel_pstate: Add separate support for Airmont cores cpufreq: intel_pstate: Replace BYT with ATOM Revert "cpufreq: intel_pstate: Use ACPI perf configuration" Revert "cpufreq: intel_pstate: Avoid calculation for max/min" ACPI-EC: Drop unnecessary check made before calling acpi_ec_delete_query() Revert "ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook" ACPI / SMBus: Fix boot stalls / high CPU caused by reentrant code PM / wakeirq: check that wake IRQ is valid before accepting it ACPI / CPPC: Use h/w reduced version of the PCCT structure x86: remove unused definition of MSR_NHM_PLATFORM_INFO tools/power turbostat: use new name for MSR_PLATFORM_INFO
2015-11-20i2c: i801: add Intel Lewisburg device IDsAlexandra Yates
Adding Intel codename Lewisburg platform device IDs for SMBus. Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-11-20Merge branches 'pm-cpufreq' and 'acpi-cppc'Rafael J. Wysocki
* pm-cpufreq: Revert "Documentation: kernel_parameters for Intel P state driver" cpufreq: mediatek: fix build error cpufreq: intel_pstate: Add separate support for Airmont cores cpufreq: intel_pstate: Replace BYT with ATOM Revert "cpufreq: intel_pstate: Use ACPI perf configuration" Revert "cpufreq: intel_pstate: Avoid calculation for max/min" * acpi-cppc: ACPI / CPPC: Use h/w reduced version of the PCCT structure
2015-11-19Revert "Documentation: kernel_parameters for Intel P state driver"Rafael J. Wysocki
Revert commit 053f56def57b (Documentation: kernel_parameters for Intel P state driver) as the code documented by it has been reverted already. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-16null_blk: register as a LightNVM deviceMatias Bjørling
Add support for registering as a LightNVM device. This allows us to evaluate the performance of the LightNVM subsystem. In /drivers/Makefile, LightNVM is moved above block device drivers to make sure that the LightNVM media managers have been initialized before drivers under /drivers/block are initialized. Signed-off-by: Matias Bjørling <m@bjorling.me> Fix by Jens Axboe to remove unneeded slab cache and the following memory leak. Signed-off-by: Jens Axboe <axboe@fb.com>
2015-11-16ipmi watchdog : add panic_wdt_timeout parameterJean-Yves Faye
In order to allow panic actions to be processed, the ipmi watchdog driver sets a new timeout value on panic. The 255s timeout was designed to allow kdump and others actions on panic, as in http://lkml.iu.edu/hypermail/linux/kernel/0711.3/0258.html This is counter-intuitive for a end-user who sets watchdog timeout value to something like 30s and who expects BMC to reset the system within 30s of a panic. This commit allows user to configure the timeout on panic. Signed-off-by: Jean-Yves Faye <jean-yves.faye@c-s.fr> Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-11-15Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds
Pull MIPS updates from Ralf Baechle: "These are the highlists of the main MIPS pull request for 4.4: - Add latencytop support - Support appended DTBs - VDSO support and initially use it for gettimeofday. - Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux - Support for the 5KE, an internal test core. - Switch all MIPS platfroms to libata drivers. - Improved support, cleanups for ralink and Lantiq platforms. - Support for the new xilfpga platform. - A number of DTB improvments for BMIPS. - Improved support for CM and CPS. - Minor JZ4740 and BCM47xx enhancements" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits) MIPS: idle: add case for CPU_5KE MIPS: Octeon: Support APPENDED_DTB MIPS: vmlinux: create a section for appended DTB MIPS: Clean up compat_siginfo_t MIPS: Fix PAGE_MASK definition MIPS: BMIPS: Enable GZIP ramdisk and timed printks MIPS: Add xilfpga defconfig MIPS: xilfpga: Add mipsfpga platform code MIPS: xilfpga: Add xilfpga device tree files. dt-bindings: MIPS: Document xilfpga bindings and boot style MIPS: Make MIPS_CMDLINE_DTB default MIPS: Make the kernel arguments from dtb available MIPS: Use USE_OF as the guard for appended dtb MIPS: BCM63XX: Use pr_* instead of printk MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND. MIPS: lantiq: Disable xbar fpi burst mode MIPS: lantiq: Force the crossbar to big endian MIPS: lantiq: Initialize the USB core on boot MIPS: lantiq: Return correct value for fpi clock on ar9 MIPS: ralink: Add missing clock on rt305x ...
2015-11-13Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull more input updates from Dmitry Torokhov: "An update to the tsc2005 driver that allows it to also support tsc2004 (basically the same controller, but uses i2c instead of spi bus), and a couple of bug fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: parkbd - drop bogus __init from parkbd_allocate_serio() Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled Input: tsc2004 - add support for tsc2004 Input: tsc200x-core - rename functions and variables Input: tsc2005 - separate SPI and core functions
2015-11-13Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull final round of SCSI updates from James Bottomley: "Sorry for the delay in this patch which was mostly caused by getting the merger of the mpt2/mpt3sas driver, which was seen as an essential item of maintenance work to do before the drivers diverge too much. Unfortunately, this caused a compile failure (detected by linux-next), which then had to be fixed up and incubated. In addition to the mpt2/3sas rework, there are updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus an assortment of changes including some year 2038 issues, a fix for a remove before detach issue in some drivers and a couple of other minor issues" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits) mpt3sas: fix inline markers on non inline function declarations sd: Clear PS bit before Mode Select. ibmvscsi: set max_lun to 32 ibmvscsi: display default value for max_id, max_lun and max_channel. mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl() scsi: pmcraid: replace struct timeval with ktime_get_real_seconds() mvumi: 64bit value for seconds_since1970 be2iscsi: Fix bogus WARN_ON length check scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice mpt3sas: Bump mpt3sas driver version to 09.102.00.00 mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs mpt2sas, mpt3sas: Update the driver versions mpt3sas: setpci reset kernel oops fix mpt3sas: Added OEM Gen2 PnP ID branding names mpt3sas: Refcount fw_events and fix unsafe list usage mpt3sas: Refcount sas_device objects and fix unsafe list usage mpt3sas: sysfs attribute to report Backup Rail Monitor Status mpt3sas: Ported WarpDrive product SSS6200 support mpt3sas: fix for driver fails EEH, recovery from injected pci bus error mpt3sas: Manage MSI-X vectors according to HBA device type ...
2015-11-13Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending Pull SCSI target updates from Nicholas Bellinger: "This series contains HCH's changes to absorb configfs attribute ->show() + ->store() function pointer usage from it's original tree-wide consumers, into common configfs code. It includes usb-gadget, target w/ drivers, netconsole and ocfs2 changes to realize the improved simplicity, that now renders the original include/target/configfs_macros.h CPP magic for fabric drivers and others, unnecessary and obsolete. And with common code in place, new configfs attributes can be added easier than ever before. Note, there are further improvements in-flight from other folks for v4.5 code in configfs land, plus number of target fixes for post -rc1 code" In the meantime, a new user of the now-removed old configfs API came in through the char/misc tree in commit 7bd1d4093c2f ("stm class: Introduce an abstraction for System Trace Module devices"). This merge resolution comes from Alexander Shishkin, who updated his stm class tracing abstraction to account for the removal of the old show_attribute and store_attribute methods in commit 517982229f78 ("configfs: remove old API") from this pull. As Alexander says about that patch: "There's no need to keep an extra wrapper structure per item and the awkward show_attribute/store_attribute item ops are no longer needed. This patch converts policy code to the new api, all the while making the code quite a bit smaller and easier on the eyes. Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>" That patch was folded into the merge so that the tree should be fully bisectable. * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits) configfs: remove old API ocfs2/cluster: use per-attribute show and store methods ocfs2/cluster: move locking into attribute store methods netconsole: use per-attribute show and store methods target: use per-attribute show and store methods spear13xx_pcie_gadget: use per-attribute show and store methods dlm: use per-attribute show and store methods usb-gadget/f_serial: use per-attribute show and store methods usb-gadget/f_phonet: use per-attribute show and store methods usb-gadget/f_obex: use per-attribute show and store methods usb-gadget/f_uac2: use per-attribute show and store methods usb-gadget/f_uac1: use per-attribute show and store methods usb-gadget/f_mass_storage: use per-attribute show and store methods usb-gadget/f_sourcesink: use per-attribute show and store methods usb-gadget/f_printer: use per-attribute show and store methods usb-gadget/f_midi: use per-attribute show and store methods usb-gadget/f_loopback: use per-attribute show and store methods usb-gadget/ether: use per-attribute show and store methods usb-gadget/f_acm: use per-attribute show and store methods usb-gadget/f_hid: use per-attribute show and store methods ...
2015-11-13Merge branch 'libnvdimm-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm fixes from Dan Williams: - three fixes tagged for -stable including a crash fix, simple performance tweak, and an invalid i/o error. - build regression fix for the nvdimm unit tests - nvdimm documentation update * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: dax: fix __dax_pmd_fault crash libnvdimm: documentation clarifications libnvdimm, pmem: fix size trim in pmem_direct_access() libnvdimm, e820: fix numa node for e820-type-12 pmem ranges tools/testing/nvdimm, acpica: fix flag rename build breakage
2015-11-13Merge tag '4.4-additional' of git://git.lwn.net/linuxLinus Torvalds
Pull more documentation updates from Jon Corbet: "A few more documentation patches that wandered in and have no reason to wait; these include some improvements to the suggestions for email clients and patch submission" * tag '4.4-additional' of git://git.lwn.net/linux: Documentation: Add minimal Mutt config for using Gmail Documentation: Add note on sending files directly with Mutt Documentation: dontdiff: remove media from dontdiff Documentation/SubmittingPatches: discuss In-Reply-To Remove email address from Documentation/filesystems/overlayfs.txt can-doc: Add missing semicolon to example
2015-11-12dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatibleCaesar Wang
This patchset attempts to new compatible for thermal founding on RK3368 SoCs. Signed-off-by: Caesar Wang <wxt@rock-chips.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2015-11-12libnvdimm: documentation clarificationsKonrad Rzeszutek Wilk
A bunch of changes that I hope will help in understanding it better for first-time readers. Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2015-11-12Merge tag '4.4-scsi-mkp' into miscJames Bottomley
SCSI queue for 4.4. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2015-11-11Merge tag 'devicetree-fixes-for-4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull DeviceTree fixes from Rob Herring: - Add empty of_translate_address needed for HiSilicon network driver. - Fix alignment requirements for CMA regions in DT. - Fix booting on PPC systems which can't do WARN() early. - Rename ak4554 binding doc from .c to .txt. * tag 'devicetree-fixes-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: of: Provide static inline function for of_translate_address if needed drivers: of: of_reserved_mem: fixup the alignment with CMA setup of: Print rather than WARN'ing when overlap check fails dt-bindings: ak4554: extension should be .txt
2015-11-11Documentation: Add minimal Mutt config for using GmailEddie Kovsky
This patch provides a minimal configuration to set up Mutt for submitting plain text patches using Gmail. Signed-off-by: Eddie Kovsky <ewk@edkovsky.org> Reviewed-by: Darren Hart <dvhart@infradead.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11Documentation: Add note on sending files directly with MuttEddie Kovsky
Like 'git send-email', Mutt can also be used to send patches generated with 'git format-patch'. This works regardless of the editor the contributor has set up to use with Mutt. Signed-off-by: Eddie Kovsky <ewk@edkovsky.org> Reviewed-by: Darren Hart <dvhart@infradead.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11Merge tag 'pwm/for-4.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm Pull pwm updates from Thierry Reding: "This round contains a couple of new drivers for the Marvell Berlin family of SoCs, various SoCs from Renesas and Broadcom as well as the backlight PWM present on MediaTek SoCs. Further existing drivers are extended to support a wider range of hardware. The remaining patches are minor fixes and cleanups across the board. Note that one of the patches included in this pull request is against arch/unicore32. I've included it here because I couldn't get a response from Guan Xuetao and I consider the change low-risk. Equivalent patches have been merged and tested in Samsung and PXA trees. The goal is to finally get rid of legacy code paths that have repeatedly been causing headaches" * tag 'pwm/for-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits) pwm: sunxi: Fix whitespace issue pwm: sysfs: Make use of the DEVICE_ATTR_[RW][WO] macro's pwm: sysfs: Remove unnecessary temporary variable unicore32: nb0916: Use PWM lookup table pwm: pwm-rcar: Revise the device tree binding document about compatible pwm: Return -ENODEV if no PWM lookup match is found pwm: sun4i: Add support for PWM controller on sun5i SoCs pwm: Set enable state properly on failed call to enable pwm: lpss: Add support for runtime PM pwm: lpss: Add more Intel Broxton IDs pwm: lpss: Support all four PWMs on Intel Broxton pwm: lpss: Add support for multiple PWMs pwm-pca9685: enable ACPI device found on Galileo Gen2 pwm: Add MediaTek display PWM driver support dt-bindings: pwm: Add MediaTek display PWM bindings pwm: tipwmss: Enable on TI DRA7x and AM437x pwm: atmel-hlcdc: add sama5d2 SoC support. pwm: Add Broadcom BCM7038 PWM controller support Documentation: dt: add Broadcom BCM7038 PWM controller binding pwm: Add support for R-Car PWM Timer ...
2015-11-11Documentation: dontdiff: remove media from dontdiffWang YanQing
media will hide all the changes in drivers/media. Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11Documentation/SubmittingPatches: discuss In-Reply-ToChris Metcalf
Add a paragraph suggesting best practices for when to link patches to previous LKML messages via In-Reply-To. Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> [jc: moved the added text to a separate section] Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11Remove email address from Documentation/filesystems/overlayfs.txtNeilBrown
I'm getting a surprising large number of questions about overlayfs sent to me personally, rather than to a relevant mailing list. So remove my email address from the documentation, and add a note about looking in the MAINTAINERS file. Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11can-doc: Add missing semicolon to exampleStefan Tatschner
The example code for CAN_BCM, connect(s, (struct sockaddr *)&addr, sizeof(addr)) lacks a semicolon at the end of the line. This patch adds that missing semicolon to ensure that the given code snippet actually compiles. Signed-off-by: Stefan Tatschner <rumpelsepp@sevenbyte.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2015-11-11Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux Pull thermal updates from Zhang Rui: - Implement generic devfreq cooling mechanism through frequency reduction for devices using devfreq. From Ørjan Eide and Javi Merino. - Introduce OMAP3 support on TI SoC thermal driver. From Pavel Mack and Eduardo Valentin. - A bounch of small fixes on devfreq_cooling, Exynos, IMX, Armada, and Rockchip thermal drivers. * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits) thermal: exynos: Directly return 0 instead of using local ret variable thermal: exynos: Remove unneeded semicolon thermal: exynos: Use IS_ERR() because regulator cannot be NULL thermal: exynos: Fix first temperature read after registering sensor thermal: exynos: Fix unbalanced regulator disable on probe failure devfreq_cooling: return on allocation failure thermal: rockchip: support the sleep pinctrl state to avoid glitches in s2r dt-bindings: rockchip-thermal: Add the pinctrl states in this document thermal: devfreq_cooling: Make power a u64 thermal: devfreq_cooling: use a thermal_cooling_device for register and unregister thermal: underflow bug in imx_set_trip_temp() thermal: armada: Fix possible overflow in the Armada 380 thermal sensor formula thermal: imx: register irq handler later in probe thermal: rockhip: fix setting thermal shutdown polarity thermal: rockchip: fix handling of invalid readings devfreq_cooling: add trace information thermal: Add devfreq cooling PM / OPP: get the voltage for all OPPs tools/thermal: tmon: use pkg-config also for CFLAGS linux/thermal.h: rename KELVIN_TO_CELSIUS to DECI_KELVIN_TO_CELSIUS ...
2015-11-11dt-bindings: MIPS: Document xilfpga bindings and boot styleZubair Lutfullah Kakakhel
Xilfpga boots only with device-tree. Document the required properties and the unique boot style Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Cc: robh+dt@kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11361/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-11-10Merge branch 'kconfig' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild Pull kconfig updates from Michal Marek: - 'make xconfig' ported to Qt5, dropping support for Qt3 - merge_config.sh supports a single-input-file mode and also respects $KCONFIG_CONFIG - Fix for incorrect display of >= and > in dependency expressions * 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (44 commits) Add current selection check. Use pkg-config to find Qt 4 and 5 instead of direct qmake kconfig: Fix copy&paste error kconfig/merge_config.sh: Accept a single file kconfig/merge_config.sh: Support KCONFIG_CONFIG Update the buildsystem for KConfig finding Qt Port xconfig to Qt5 - Update copyright. Port xconfig to Qt5 - Fix goParent issue. Port xconfig to Qt5 - on Back clicked, deselect old item. Port xconfig to Qt5 - Add(back) one click checkbox toggle. Port xconfig to Qt5 - Add(back) lineedit editing. Port xconfig to Qt5 - Remove some commented code. Port xconfig to Qt5 - Source format. Port xconfig to Qt5 - Add horizontal scrollbar, and scroll per pixel. Port xconfig to Qt5 - Change ConfigItem constructor parent type. Port xconfig to Qt5 - Disable ConfigList soring Port xconfig to Qt5 - Remove ConfigList::updateMenuList template. Port xconfig to Qt5 - Add ConfigList::mode to initializer list. Port xconfig to Qt5 - Add ConfigItem::nextItem to initializer list. Port xconfig to Qt5 - Tree widget set column titles. ...
2015-11-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet. 2) Several spots need to get to the original listner for SYN-ACK packets, most spots got this ok but some were not. Whilst covering the remaining cases, create a helper to do this. From Eric Dumazet. 3) Missiing check of return value from alloc_netdev() in CAIF SPI code, from Rasmus Villemoes. 4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich. 5) Use after free in mvneta driver, from Justin Maggard. 6) Fix race on dst->flags access in dst_release(), from Eric Dumazet. 7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd Bergmann. 8) Fix multicast getsockopt deadlock, from WANG Cong. 9) Fix deadlock in btusb, from Kuba Pawlak. 10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6 counter state. From Sabrina Dubroca. 11) Fix packet_bind() race, which can cause lost notifications, from Francesco Ruggeri. 12) Fix MAC restoration in qlcnic driver during bonding mode changes, from Jarod Wilson. 13) Revert bridging forward delay change which broke libvirt and other userspace things, from Vlad Yasevich. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits) Revert "bridge: Allow forward delay to be cfgd when STP enabled" bpf_trace: Make dependent on PERF_EVENTS qed: select ZLIB_INFLATE net: fix a race in dst_release() net: mvneta: Fix memory use after free. net: Documentation: Fix default value tcp_limit_output_bytes macvtap: Resolve possible __might_sleep warning in macvtap_do_read() mvneta: add FIXED_PHY dependency net: caif: check return value of alloc_netdev net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA drivers: net: xgene: fix RGMII 10/100Mb mode netfilter: nft_meta: use skb_to_full_sk() helper net_sched: em_meta: use skb_to_full_sk() helper sched: cls_flow: use skb_to_full_sk() helper netfilter: xt_owner: use skb_to_full_sk() helper smack: use skb_to_full_sk() helper net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid() bpf: doc: correct arch list for supported eBPF JIT dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put" bonding: fix panic on non-ARPHRD_ETHER enslave failure ...
2015-11-10dt-bindings: ak4554: extension should be .txtRaphael Poggi
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
2015-11-10Merge tag 'armsoc-dt' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM DT updates from Olof Johansson: "As usual, this is the massive branch we have for each release. Lots of various updates and additions of hardware descriptions on existing hardware, as well as the usual additions of new boards and SoCs. This is also the first release where we've started mixing 64- and 32-bit DT updates in one branch. (Specific details on what's actually here and new is pretty easy to tell from the diffstat, so there's little point in duplicating listing it here)" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits) ARM: dts: uniphier: add system-bus-controller nodes ARM64: juno: disable NOR flash node by default ARM: dts: uniphier: add outer cache controller nodes arm64: defconfig: Enable PCI generic host bridge by default arm64: Juno: Add support for the PCIe host bridge on Juno R1 Documentation: of: Document the bindings used by Juno R1 PCIe host bridge ARM: dts: uniphier: add I2C aliases for ProXstream2 boards dts/Makefile: Add build support for LS2080a QDS & RDB board DTS dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards dts/ls2080a: Update Simulator DTS to add support of various peripherals dts/ls2080a: Remove text about writing to Free Software Foundation dts/ls2080a: Update DTSI to add support of various peripherals doc: DTS: Update DWC3 binding to provide reference to generic bindings doc/bindings: Update GPIO devicetree binding documentation for LS2080A Documentation/dts: Move FSL board-specific bindings out of /powerpc Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards arm64: Rename FSL LS2085A SoC support code to LS2080A arm64: Use generic Layerscape SoC family naming ARM: dts: uniphier: add ProXstream2 Vodka board support ARM: dts: uniphier: add ProXstream2 Gentil board support ...
2015-11-10Merge tag 'armsoc-drivers' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "As we've enabled multiplatform kernels on ARM, and greatly done away with the contents under arch/arm/mach-*, there's still need for SoC-related drivers to go somewhere. Many of them go in through other driver trees, but we still have drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code that might be shared between ARM and ARM64 (or just in general makes sense to not have under the architecture directory). This branch contains mostly such code: - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate with power management blocks on these SoCs for use by clock, regulator and bus frequency drivers. - Allwinner Reduced Serial Bus driver, again used to communicate with PMICs. - Drivers for ARM's SCPI (System Control Processor). Not to be confused with PSCI (Power State Coordination Interface). SCPI is used to communicate with the assistant embedded cores doing power management, and we have yet to see how many of them will implement this for their hardware vs abstracting in other ways (or not at all like in the past). - To make confusion between SCPI and PSCI more likely, this release also includes an update of PSCI to interface version 1.0. - Rockchip support for power domains. - A driver to talk to the firmware on Raspberry Pi" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits) soc: qcom: smd-rpm: Correct size of outgoing message bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings ARM: bcm2835: add mutual inclusion protection drivers: psci: make PSCI 1.0 functions initialization version dependent dt-bindings: Correct paths in Rockchip power domains binding document soc: rockchip: power-domain: don't try to print the clock name in error case soc: qcom/smem: add HWSPINLOCK dependency clk: berlin: add cpuclk ARM: berlin: dts: add CLKID_CPU for BG2Q ARM: bcm2835: Add the Raspberry Pi firmware driver soc: qcom: smem: Move RPM message ram out of smem DT node soc: qcom: smd-rpm: Correct the active vs sleep state flagging soc: qcom: smd: delete unneeded of_node_put firmware: qcom-scm: build for correct architecture level soc: qcom: smd: Correct SMEM items for upper channels qcom-scm: add missing prototype for qcom_scm_is_available() qcom-scm: fix endianess issue in __qcom_scm_is_call_available soc: qcom: smd: Reject send of too big packets soc: qcom: smd: Handle big endian CPUs ...
2015-11-10Merge tag 'armsoc-soc' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform updates from Olof Johansson: "New and/or improved SoC support for this release: Marvell Berlin: - Enable standard DT-based cpufreq - Add CPU hotplug support Freescale: - Ethernet init for i.MX7D - Suspend/resume support for i.MX6UL Allwinner: - Support for R8 chipset (used on NTC's $9 C.H.I.P board) Mediatek: - SMP support for some platforms Uniphier: - L2 support - Cleaned up SMP support, etc. plus a handful of other patches around above functionality, and a few other smaller changes" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits) ARM: uniphier: rework SMP operations to use trampoline code ARM: uniphier: add outer cache support Documentation: EXYNOS: Update bootloader interface on exynos542x ARM: mvebu: add broken-idle option ARM: orion5x: use mac_pton() helper ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned ARM: sunxi: Add R8 support ARM: digicolor: select pinctrl/gpio driver arm: berlin: add CPU hotplug support arm: berlin: use non-self-cleared reset register to reset cpu ARM: mediatek: add smp bringup code ARM: mediatek: enable gpt6 on boot up to make arch timer working soc: mediatek: Fix random hang up issue while kernel init soc: ti: qmss: make acc queue support optional in the driver soc: ti: add firmware file name as part of the driver Documentation: dt: soc: Add description for knav qmss driver ARM: S3C64XX: Use PWM lookup table for mach-smartq ARM: S3C64XX: Use PWM lookup table for mach-hmt ARM: S3C64XX: Use PWM lookup table for mach-crag6410 ARM: S3C64XX: Use PWM lookup table for smdk6410 ...
2015-11-10Merge tag 'armsoc-cleanup' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "Again we have a sizable (but not huge) cleanup branch with a net delta of about -3k lines. Main contents here is: - A bunch of development/cleanup of a few PXA boards - Removal of bockw platforms on shmobile, since the platform has now gone completely multiplatform. Whee! - move of the 32kHz timer on OMAP to a proper timesource - Misc cleanup of older OMAP material (incl removal of one board file) - Switch over to new common PWM lookup support for several platforms There's also a handful of other cleanups across the tree, but the above are the major pieces" * tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits) ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs ARM: DRA7: hwmod data: Remove spinlock hwmod addrs ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data ARM: Remove __ref on hotplug cpu die path ARM: Remove open-coded version of IRQCHIP_DECLARE arm: omap2: board-generic: use omap4_local_timer_init for AM437x ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data ARM: OMAP: Remove duplicated operand in OR operation clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode ARM: pxa: raumfeld: make some variables static ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c ARM: OMAP2+: Rename cpu_is macros to soc_is arm: omap2: timer: limit hwmod usage to non-DT boots arm: omap2+: select 32k clocksource driver clocksource: add TI 32.768 Hz counter driver arm: omap2: timer: rename omap_sync32k_timer_init() arm: omap2: timer: always call clocksource_of_init() when DT arm: omap2: timer: move realtime_counter_init() around ...
2015-11-10Merge tag 'libnvdimm-for-4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm updates from Dan Williams: "Outside of the new ACPI-NFIT hot-add support this pull request is more notable for what it does not contain, than what it does. There were a handful of development topics this cycle, dax get_user_pages, dax fsync, and raw block dax, that need more more iteration and will wait for 4.5. The patches to make devm and the pmem driver NUMA aware have been in -next for several weeks. The hot-add support has not, but is contained to the NFIT driver and is passing unit tests. The coredump support is straightforward and was looked over by Jeff. All of it has received a 0day build success notification across 107 configs. Summary: - Add support for the ACPI 6.0 NFIT hot add mechanism to process updates of the NFIT at runtime. - Teach the coredump implementation how to filter out DAX mappings. - Introduce NUMA hints for allocations made by the pmem driver, and as a side effect all devm allocations now hint their NUMA node by default" * tag 'libnvdimm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: coredump: add DAX filtering for FDPIC ELF coredumps coredump: add DAX filtering for ELF coredumps acpi: nfit: Add support for hot-add nfit: in acpi_nfit_init, break on a 0-length table pmem, memremap: convert to numa aware allocations devm_memremap_pages: use numa_mem_id devm: make allocations numa aware by default devm_memremap: convert to return ERR_PTR devm_memunmap: use devres_release() pmem: kill memremap_pmem() x86, mm: quiet arch_add_memory()
2015-11-10Merge branch 'i2c/for-4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: - New drivers: UniPhier (with and without FIFO) - some drivers got some bigger rework: ismt, designware, img-scb (rcar had to be reverted because issues were showing up just lately) - ACPI: reworked the device scanning and added support for muxes ... and quite a lot of driver bugfixes and cleanups this time. All files touched outside of the i2c realm have proper acks. * 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits) i2c: rcar: Revert the latest refactoring series i2c: pnx: remove superfluous assignment MAINTAINERS: i2c: drop i2c-pnx maintainer MAINTAINERS: i2c: mark also subdirectories as maintained i2c: cadence: enable driver for ARM64 i2c: i801: Document Intel DNV and Broxton i2c: at91: manage unexpected RXRDY flag when starting a transfer i2c: pnx: Use setup_timer instead of open coding it i2c: add ACPI support for I2C mux ports acpi: add acpi_preset_companion() stub i2c: pxa: Add support for pxa910/988 & new configuration features i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource i2c-dev: Fix I2C_SLAVE ioctl comment i2c-dev: Fix typo in ioctl name reference i2c: sirf: tune the divider to make i2c bus freq more accurate i2c: imx: Use -ENXIO as error in the NACK case i2c: i801: Add support for Intel Broxton i2c: i801: Add support for Intel DNV i2c: mediatek: add i2c resume support i2c: imx: implement bus recovery ...
2015-11-10Merge git://www.linux-watchdog.org/linux-watchdogLinus Torvalds
Pull watchdog update from Wim Van Sebroeck: - New driver for Broadcom 7038 Set-Top Box - imx2_wdt: Use register definition in regmap_write() - intel-mid: add Magic Closure flag - watchdog framework improvements: - Use device tree alias for naming watchdogs - propagate ping error code to the user space - Always evaluate new timeout against min_timeout - Use single variable name for struct watchdog_device - include clean-ups * git://www.linux-watchdog.org/linux-watchdog: watchdog: include: add units for timeout values in kerneldoc watchdog: include: fix some typos watchdog: core: propagate ping error code to the user space watchdog: watchdog_dev: Use single variable name for struct watchdog_device watchdog: Always evaluate new timeout against min_timeout watchdog: intel-mid: add Magic Closure flag watchdog: imx2_wdt: Use register definition in regmap_write() watchdog: watchdog_dev: Use device tree alias for naming watchdogs watchdog: Watchdog driver for Broadcom Set-Top Box watchdog: bcm7038: add device tree binding documentation
2015-11-10Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dmaLinus Torvalds
Pull dmaengine updates from Vinod Koul: "This time we have a very typical update which is mostly fixes and updates to drivers and no new drivers. - the biggest change is coming from Peter for edma cleanup which even caused some last minute regression, things seem settled now - idma64 and dw updates - iotdma updates - module autoload fixes for various drivers - scatter gather support for hdmac" * tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits) dmaengine: edma: Add dummy driver skeleton for edma3-tptc Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3" Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3" dmaengine: dw: some Intel devices has no memcpy support dmaengine: dw: platform: provide platform data for Intel dmaengine: dw: don't override platform data with autocfg dmaengine: hdmac: Add scatter-gathered memset support dmaengine: hdmac: factorise memset descriptor allocation dmaengine: virt-dma: Fix kernel-doc annotations ARM: DTS: am437x: Use the new DT bindings for the eDMA3 ARM: DTS: am33xx: Use the new DT bindings for the eDMA3 dmaengine: edma: New device tree binding dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx dmaengine: edma: Merge the of parsing functions dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot dmaengine: edma: Refactor the dma device and channel struct initialization dmaengine: edma: Get qDMA channel information from HW also dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_) ...
2015-11-10Merge tag 'rtc-v4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux Pull RTC updates from Alexandre Belloni: "Core: - Fix rtctest error path New drivers: - Microcrystal RV8803 Subsystem wide cleanups: - remove misuse of IRQF_NO_SUSPEND flag Drivers: - at91rm9200: clear RTC alarm status flag prior to suspending - davinci: remove incorrect reference to probe function - ds1307: Fix alarm programming for mcp794xx - ds1390: trickle charger support, fix ds1390_get_reg - isl1208: Pass the IRQF_ONESHOT flag - opal: fix type of token - pcf2127: fix RTC_READ_VL, remove useless driver version - pcf85063: return an error when date is invalid - pcf8563: add CLKOUT to common clock framework - rx8025: remove unnecessary braces - s3c: Set year, month, day value for setting alarm - stmp3xxx: unify register access macros - License fixes: pcf2127, da9063 - wakeup-source support for isl12057 and opal" * tag 'rtc-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (23 commits) rtc: Add a driver for Micro Crystal RV8803 rtc: s3c: Set year, month, day value for setting alarm rtc: ds1307: Fix alarm programming for mcp794xx rtc: isl12057: enable support for the standard "wakeup-source" property rtc: opal: enable support for the stardard "wakeup-source" property rtc: isl1208: Pass the IRQF_ONESHOT flag rtc: pcf8563: add CLKOUT to common clock framework rtc: davinci: remove incorrect reference to probe function rtc: at91rm9200: clear RTC alarm status flag prior to suspending rtc: pcf2127: remove useless driver version rtc: pcf2127: fix reading uninitialized value on RTC_READ_VL ioctl rtc: stmp3xxx: unify register access macros rtc: da9063: GPL copyright inconsistency fix rtc: pcf85063: return an error when date is invalid rtc: rx8025: remove unnecessary braces rtc: ds1343: remove misuse of IRQF_NO_SUSPEND flag rtc: ab8500: remove misuse of IRQF_NO_SUSPEND flag rtc: pl031: remove misuse of IRQF_NO_SUSPEND flag rtc: opal: fix type of token rtc: ds1390: Add trickle charger device tree binding ...
2015-11-10Merge tag 'fbdev-4.4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux Pull fbdev updates from Tomi Valkeinen: - omap: fix hdmi audio configuration issue - ssd1307fb: add ssd1309 support - tridentfb: support DDC - gxt4500: enable support for non-PPC platforms * tag 'fbdev-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: radeonfb: Deinline large functions gxt4500: enable panning gxt4500: Use arch_phys_wc_* for framebuffer gxt4500: fix color order gxt4500: fix 16bpp 565 mode gxt4500: enable on non-PPC architectures tridentfb: Add DDC support fb_ddc: Allow I2C adapters without SCL read capability fbdev: ssd1307fb: add ssd1309 support fbdev: ssd1307fb: alphabetize headers video/omap: remove invalid check OMAPDSS: hdmi: Reconfigure and restart audio when display is enabled
2015-11-10Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm updates from Dave Airlie: "I Was Almost Tempted To Capitalise Every Word, but then I decided I couldn't read it myself! I've also got one pull request for the sti driver outstanding. It relied on a commit in Greg's tree and I didn't find out in time, that commit is in your tree now so I might send that along once this is merged. I also had the accidental misfortune to have access to a Skylake on my desk for a few days, and I've had to encourage Intel to try harder, which seems to be happening now. Here is the main drm-next pull request for 4.4. Highlights: New driver: vc4 driver for the Rasberry Pi VPU. (From Eric Anholt at Broadcom.) Core: Atomic fbdev support Atomic helpers for runtime pm dp/aux i2c STATUS_UPDATE handling struct_mutex usage cleanups. Generic of probing support. Documentation: Kerneldoc for VGA switcheroo code. Rename to gpu instead of drm to reflect scope. i915: Skylake GuC firmware fixes HPD A support VBT backlight fallbacks Fastboot by default for some systems FBC work BXT/SKL workarounds Skylake deeper sleep state fixes amdgpu: Enable GPU scheduler by default New atombios opcodes GPUVM debugging options Stoney support. Fencing cleanups. radeon: More efficient CS checking nouveau: gk20a instance memory handling improvements. Improved PGOB detection and GK107 support Kepler GDDR5 PLL statbility improvement G8x/GT2xx reclock improvements new userspace API compatiblity fixes. virtio-gpu: Add 3D support - qemu 2.5 has it merged for it's gtk backend. msm: Initial msm88896 (snapdragon 8200) exynos: HDMI cleanups Enable mixer driver byt default Add DECON-TV support vmwgfx: Move to using memremap + fixes. rcar-du: Add support for R8A7793/4 DU armada: Remove support for non-component mode Improved plane handling Power savings while in DPMS off. tda998x: Remove unused slave encoder support Use more HDMI helpers Fix EDID read handling dwhdmi: Interlace video mode support for ipu-v3/dw_hdmi Hotplug state fixes Audio driver integration imx: More color formats support. tegra: Minor fixes/improvements" [ Merge fixup: remove unused variable 'dev' that had all uses removed in commit 4e270f088011: "drm/gem: Drop struct_mutex requirement from drm_gem_mmap_obj" ] * 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits) drm/vmwgfx: Relax irq locking somewhat drm/vmwgfx: Properly flush cursor updates and page-flips drm/i915/skl: disable display side power well support for now drm/i915: Extend DSL readout fix to BDW and SKL. drm/i915: Do graphics device reset under forcewake drm/i915: Skip fence installation for objects with rotated views (v4) vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT drm/amdgpu: group together common fence implementation drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE drm/amdgpu: remove now unused fence functions drm/amdgpu: fix fence fallback check drm/amdgpu: fix stoping the scheduler timeout drm/amdgpu: cleanup on error in amdgpu_cs_ioctl() drm/i915: Fix locking around GuC firmware load drm/amdgpu: update Fiji's Golden setting drm/amdgpu: update Fiji's rev id drm/amdgpu: extract common code in vi_common_early_init drm/amd/scheduler: don't oops on failure to load drm/amdgpu: don't oops on failure to load (v2) drm/amdgpu: don't VT switch on suspend ...
2015-11-10pwm: pwm-rcar: Revise the device tree binding document about compatibleYoshihiro Shimoda
The compatible should be "renesas,pwm-rcar", and one the the SoC specific string. So, this patch revises the documentation. Reported-by: Rob Herring <robh+dt@kernel.org> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2015-11-10pwm: sun4i: Add support for PWM controller on sun5i SoCsHans de Goede
The PWM controller on sun5i SoCs is identical to the one found on sun7i SoCs. On the A13 package only one of the 2 pins is routed to the outside, so only advertise one PWM channel there. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com>