| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 7141209db9c335ab261a17933809a3e660ebdc12 ]
Primary Ethernet interface is connected to the port 8 (not 5).
Fixes: 64612828628c ("ARM: dts: BCM53573: Add Tenda AC9 switch ports")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230723195416.7831-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44ad8207806973f4e4f7d870fff36cc01f494250 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f50a ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6cae7 ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 982655cb0e7f18934d7532c32366e574ad61dbd7 ]
The davicom,dm9000 Ethernet Controller accepts two reg addresses.
Fixes: b672b27d232e ("ARM: dts: Add Device tree for s5pc110/s5pv210 boards")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20230713152926.82884-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b77904ba177a9c67b6dbc3637fdf1faa22df6e5c ]
Backlight is supplied by DC5V regulator. The DTS has no PMIC node, so
just add a regulator-fixed to solve it and fix dtbs_check warning:
s5pv210-smdkv210.dtb: backlight: 'power-supply' is a required property
Link: https://lore.kernel.org/r/20230421095721.31857-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Stable-dep-of: 982655cb0e7f ("ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf0cb2af6a18f28b84f9f1416bff50ca60d6e98a ]
The davicom,dm9000 Ethernet Controller accepts two reg addresses.
Fixes: a43736deb47d ("ARM: dts: Add dts file for S3C6410-based Mini6410 board")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20230713152926.82884-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c0fd6b3d0778ceab40205315ccef74568490f17 ]
Switch away from deprecated properties.
This fixes:
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-sck: False schema does not allow [[3, 21, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-miso: False schema does not allow [[3, 22, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: gpio-mosi: False schema does not allow [[3, 23, 0]]
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: 'sck-gpios' is a required property
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
arch/arm/boot/dts/broadcom/bcm947189acdbmr.dtb: spi: Unevaluated properties are not allowed ('gpio-miso', 'gpio-mosi', 'gpio-sck' were unexpected)
From schema: Documentation/devicetree/bindings/spi/spi-gpio.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-4-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3392ef368d9b04622fe758b1079b512664b6110a ]
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-3-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05d2c3d552b8c92fc397377d9d1112fc58e2cd59 ]
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-2-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit deb7edbc27a6ec4d8f5edfd8519b7ed13cbd2a52 ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9bcfc3cdc903485a52c6f471f4ae96a41fa51803 ]
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: deb7edbc27a6 ("ARM: dts: stm32: Add missing detach mailbox for DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 966f04a89d77548e673de2c400abe0b2cf5c15db ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84a34e1862aae43e4dcdfb743a7dd3ade1fe4a3c ]
"make dtbs_check" gives following output :
stm32mp157c-odyssey.dt.yaml: gpu@59000000: 'contiguous-area' does not match
any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpu/vivante,gc.yaml
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 966f04a89d77 ("ARM: dts: stm32: Add missing detach mailbox for Odyssey SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ee0ef38aa9f75f21b51f729dd42b2e932515188 ]
Add missing "detach" mailbox to this board to permit the CPU to inform
the remote processor on a detach. This signal allows the remote processor
firmware to stop IPC communication and to reinitialize the resources for
a re-attach.
Without this mailbox, detach is not possible and kernel log contains the
following warning to, so make sure all the STM32MP15xx platform DTs are
in sync regarding the mailboxes to fix the detach issue and the warning:
"
stm32-rproc 10000000.m4: mbox_request_channel_byname() could not locate channel named "detach"
"
Fixes: 6257dfc1c412 ("ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c46e9b6cc98245f7264a8d15394d1f95d433abec ]
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 0ee0ef38aa9f ("ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc8d2b21bc5d5d7a6eadaa8c2a5d2e6856689480 ]
"make dtbs_check" gives following output :
stm32mp157c-emstamp-argon.dtb: gpu@59000000: 'contiguous-area' does not match
any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpu/vivante,gc.yaml
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 0ee0ef38aa9f ("ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a306d8962a24f4e8385853793fd58f9792c7aa61 ]
Replace "mdio0" node with "mdio" to match mdio.yaml DT schema.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 0ee0ef38aa9f ("ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86684c2481b6e6a46c2282acee13554e34e66071 ]
Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.
Signed-off-by: Rob Herring <robh@kernel.org>
Stable-dep-of: 92632115fb57 ("samples/bpf: fix bio latency check with tracepoint")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4697b5848bd933f68ebd04836362c8de0cacaf71 ]
Since commit 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store
thread_info->abi_syscall"), the seccomp selftests "syscall_errno"
and "syscall_faked" have been broken. Both seccomp and PTRACE depend
on using the special value of "-1" for skipping syscalls. This value
wasn't working because it was getting masked by __NR_SYSCALL_MASK in
both PTRACE_SET_SYSCALL and get_syscall_nr().
Explicitly test for -1 in PTRACE_SET_SYSCALL and get_syscall_nr(),
leaving it exposed when present, allowing tracers to skip syscalls
again.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store thread_info->abi_syscall")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230810195422.2304827-2-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf007647475b5090819c5fe8da771073145c7334 ]
Since commit 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store
thread_info->abi_syscall"), the seccomp selftests "syscall_restart" has
been broken. This was caused by the restart syscall not being stored to
"abi_syscall" during restart setup before branching to the "local_restart"
label. Tracers would see the wrong syscall, and scno would get overwritten
while returning from the TIF_WORK path. Add the missing store.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store thread_info->abi_syscall")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230810195422.2304827-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be18293e47cbca7c6acee9231fc851601d69563a ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
mmc0: Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx7s.dtsi#L1216-L1217
Fixes: 1e336aa0c025 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0faa29c4207e6e29cfc81b427df60e326c37083a upstream.
The spitz board file uses the obscure symbol_get() function
to optionally call a function from sharpsl_pm.c if that is
built. However, the two files are always built together
these days, and have been for a long time, so this can
be changed to a normal function call.
Link: https://lore.kernel.org/lkml/20230731162639.GA9441@lst.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6846234f45801441f0e31a8b37f901ef0abd2df upstream.
Today module_frob_arch_sections() spots init sections from their
'init' prefix, and uses this to keep the init PLTs separate from the rest.
get_module_plt() uses within_module_init() to determine if a
location is in the init text or not, but this depends on whether
core code thought this was an init section.
Naturally the logic is different.
module_init_layout_section() groups the init and exit text together if
module unloading is disabled, as the exit code will never run. The result
is kernels with this configuration can't load all their modules because
there are not enough PLTs for the combined init+exit section.
A previous patch exposed module_init_layout_section(), use that so the
logic is the same.
Fixes: 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()")
Cc: stable@vger.kernel.org
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a2b96e42a0284c4fc03022236f656a085ca714a ]
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c025 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 762b700982a1e0f562184363f19860c3b9bdd0bf ]
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef477 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Stefan Riedmüller <s.riedmueller@phytec.de>
Fixes: 800d595151bb ("ARM: dts: imx6: Add initial support for phyBOARD-Mira")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b0d1f2738899dbcc7a026d826373530019aa31b ]
The node names should be generic and DT schema expects certain pattern:
imx50-kobo-aura.dtb: gpio-leds: 'on' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
imx6dl-yapp4-draco.dtb: led-controller@30: 'chan@0', 'chan@1', 'chan@2' do not match any of the regexes: '^led@[0-8]$', '^multi-led@[0-8]$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: 762b700982a1 ("ARM: dts: imx6: phytec: fix RTC interrupt level")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee70b908f77a9d8f689dea986f09e6d7dc481934 ]
Property name "phy-3p0-supply" is used instead of "phy-reg_3p0-supply".
Fixes: 9f30b6b1a957 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1d14bd943fa2bbdfda1efbcc080b298fed5f1803 ]
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ee31bb0524a2e7c99b03f50249a411cc1eaa411f upstream
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.078124882@linutronix.de
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8ef1233939495c405a9faa4bd1ae7d3f581bae4 upstream.
The DT version of this board has a custom file with the gpio
device. However, it does nothing because the d2net_init()
has no caller or prototype:
arch/arm/mach-orion5x/board-d2net.c:101:13: error: no previous prototype for 'd2net_init'
Call it from the board-dt file as intended.
Fixes: 94b0bd366e36 ("ARM: orion5x: convert d2net to Device Tree")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230516153109.514251-10-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit edcbdd57de499305e2a3737d4a73fe387f71d84c upstream.
After renaming NAND controller node name from "qpic-nand" to
"nand-controller", the board DTS/DTSI also have to be updated:
Warning (unit_address_vs_reg): /soc/qpic-nand@79b0000: node has a unit name, but no reg or ranges property
Cc: <stable@vger.kernel.org>
Fixes: 9e1e00f18afc ("ARM: dts: qcom: Fix node name for NAND controller node")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230420072811.36947-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fcb79ee3f0b15ed15f35eca5f24e952fdced9c61 ]
The pinctrl node was missing which change the pin mux to GPIO mode.
Add it so we don't have to rely on the bootloader to set the correct
mode.
Fixes: 79d83b3a458e ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230616-feature-d10-dt-cleanups-v1-2-50dd0452b8fe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bfcd5714f6424c03e385e0e9296dcd69855cfea7 ]
The pinctrl node was missing which change the pin mux to GPIO mode. Add
it.
Fixes: 79d83b3a458e ("ARM: dts: lan966x: add basic Kontron KSwitch D10 support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
[claudiu.beznea: moved pinctrl-* bindings after compatible]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230616-feature-d10-dt-cleanups-v1-1-50dd0452b8fe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd274b733bfdde3ca72f0fa2a37f032f3a8c402c ]
this typo was found by the dtbs_check
| ports:port@5:fixed-link: 'oneOf' conditional failed,
| {'speed': [[1000]], 'duplex-full': True} is not of type 'array'
| 'duplex-full' does not match any of the regexes: 'pinctrl-[0-]..."
this should have been full-duplex;
Fixes: 935327a73553 ("ARM: dts: BCM5301X: Add DT for Meraki MR26")
Fixes: ec88a9c344d9 ("ARM: BCM5301X: Add DT for Meraki MR32")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/50522f45566951a9eabd22820647924cc6b4a264.1686238550.git.chunkeey@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 076c74c592cabe4a47537fe5205b5b678bed010d ]
Use "dai-format" to configure DAI audio format as specified in
audio-graph-port.yaml bindings.
Fixes: 144d1ba70548 ("ARM: dts: stm32: Adapt STM32MP157 DK boards to stm32 DT diversity")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3f2778b1b6ced649bffdc7cbb05b80bb92f2108 ]
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0501fdec106a291c43b3c1b525cf22ab4c24b2d8 ]
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e9325d05b ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98b503c7fb13a17a47d8ebf15fa8f7c10118e75c ]
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55/
Fixes: 57007bfb5469 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e60c230588d88036f974cec7e93361e2c4f62226 ]
Add the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board stalls
during the boot for some reason (most probably because TZ mishandles the
protection error and keeps on looping somewhere inside).
Fixes: 62bc81792223 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-3-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0cf765e598712addec34d0208cc1418c151fefb2 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da342772 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 861bc1d2886d47bd57a2cbf2cda87fdbe3eb9d08 ]
omap2 contains a hack to define tick_broadcast() on non-SMP
configurations in place of the normal SMP definition. This one
causes a warning because of a missing prototype:
arch/arm/mach-omap2/board-generic.c:44:6: error: no previous prototype for 'tick_broadcast'
Make sure to always include the header with the declaration.
Fixes: d86ad463d670 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230516153109.514251-9-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 419013740ea1e4343d8ade535d999f59fa28e460 ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817bf ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 311bbc884b2edcf584b67d331be85ce43b27586f ]
Align RPM requests node with DT schema by using hyphen instead of
underscore.
Fixes: f300826d27be ("ARM: dts: qcom-msm8974: Sort and clean up nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230410175232.22317-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ffec92e70ac5097b9f67ec154065305b16a3b46 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2c3 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9660efc2af37f3c12dc6e6a5511ad99e0addc297 ]
The ethernet MAC EEPROM is not populated on the SoM itself, it has to be
populated on each carrier board. Move the EEPROM into the correct place
in DTs, i.e. the carrier board DTs. Add label to the EEPROM too.
Fixes: 7e76f82acd9e1 ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d542ce8d4769cdef6a7bc3437e59cfed9c68f0e4 ]
With the current device tree for meson8b, uarts B (e.g. available on pins
8/10 on Odroid-C1) and C (pins 3/5 on Odroid-C1) do not work, because they
are relying on incorrect clocks. Change the references of pclk to the
correct CLKID, to allow use of the two uarts.
Fixes: 3375aa77135f ("ARM: dts: meson8b: Fix the UART device-tree schema validation")
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d3c8e2c5757153bbfad70019ec1decbca86f3def ]
There is no such property in the SPI controller binding documentation.
Also Linux driver doesn't look for it.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230503122830.3200-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dda5f312bb09e56e7a1c3e3851f2000eb2e9c879 ]
The sync_*() ops on arch/arm are defined in terms of the regular bitops
with no special handling. This is not correct, as UP kernels elide
barriers for the fully-ordered operations, and so the required ordering
is lost when such UP kernels are run under a hypervsior on an SMP
system.
Fix this by defining sync ops with the required barriers.
Note: On 32-bit arm, the sync_*() ops are currently only used by Xen,
which requires ARMv7, but the semantics can be implemented for ARMv6+.
Fixes: e54d2f61528165bb ("xen/arm: sync_bitops")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230605070124.3741859-2-mark.rutland@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b9c3ddcec6a55e15d3e38e7405e2d078db02020 ]
checker_stack_use_t32strd() and kprobe_handler() can be made static since
they are not used from other files, while coverage_start_registers()
and __kprobes_test_case() are used from assembler code, and just need
a declaration to avoid a warning with the global definition.
arch/arm/probes/kprobes/checkers-common.c:43:18: error: no previous prototype for 'checker_stack_use_t32strd'
arch/arm/probes/kprobes/core.c:236:16: error: no previous prototype for 'kprobe_handler'
arch/arm/probes/kprobes/test-core.c:723:10: error: no previous prototype for 'coverage_start_registers'
arch/arm/probes/kprobes/test-core.c:918:14: error: no previous prototype for '__kprobes_test_case_start'
arch/arm/probes/kprobes/test-core.c:952:14: error: no previous prototype for '__kprobes_test_case_end_16'
arch/arm/probes/kprobes/test-core.c:967:14: error: no previous prototype for '__kprobes_test_case_end_32'
Fixes: 6624cf651f1a ("ARM: kprobes: collects stack consumption for store instructions")
Fixes: 454f3e132d05 ("ARM/kprobes: Remove jprobe arm implementation")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8b35ca3e45e35a26a21427f35d4093606e93ad0a upstream.
arm has an additional check for address < FIRST_USER_ADDRESS before
expanding the stack. Since FIRST_USER_ADDRESS is defined everywhere
(generally as 0), move that check to the generic expand_downwards().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4a672d500bfd6bb87092c33d5a2572c3d0a1cf83 ]
Several device tree files get the polarity of the pendown-gpios
wrong: this signal is active low. Fix up all incorrect flags, so
that operating systems can rely on the flag being correctly set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230510105156.1134320-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
