| Age | Commit message (Collapse) | Author |
|---|
|
The Netgear R6200 v1 uses a BCM4718A1 SOC and a BCM4352/BCM4360 for 5GHz
wireless. This patch adds support for detecting this model board and
registers the 3 buttons.
I have tested that the device can boot kernels 4.14 and 4.19 under
OpenWRT.
There is one issue that the LEDs on the device are controlled by a
74HC164 that uses bit-banging instead of SPI so it isn't accessible to
the kernel without adding a workaround. Without any workaround the
device on boot will flash all LEDs once then the power LED will remain
amber as all other LEDs stay off.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[paul.burton@mips.com:
- Sort bcm47xx_board_list_board_id alphabetically by board type.
- Fix whitespace.
- Wrap commit message & drop OpenWRT-based justification for
bcm47xx_board_list_board_id being mis-sorted.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A small batch of MIPS fixes for 5.1:
- An interrupt masking fix for Loongson-based Lemote 2F systems (fixing
a regression from v3.19).
- A relocation fix for configurations in which the devicetree is stored
in an ELF section (fixing a regression from v4.7).
- Fix jump labels for MIPSr6 kernels where they previously could
inadvertently place a control transfer instruction in a forbidden slot
& take unexpected exceptions (fixing MIPSr6 support added in v4.0).
- Extend an existing USB power workaround for the Netgear WNDR3400 to v2
boards in addition to the v3 ones that already used it.
- Remove the custom MIPS32 definition of __kernel_fsid_t to make it
consistent with MIPS64 & every other architecture, in particular
resolving issues for code which tries to print the val field whose
type previously differed (though had identical memory layout).
Merged into mips-next to gain the MIPSr6 jump label fix before enabling
jump labels by default for generic kernel builds.
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Formatting of Kconfig files doesn't look so pretty, so let the
Great White Handkerchief come around and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-kernel@vger.kernel.org
Cc: hauke@hauke-m.de
Cc: zajec5@gmail.com
Cc: f.fainelli@gmail.com
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
|
|
Eric has reported on OpenWrt's bug tracking system[1], that he's not
able to use USB devices on his WNDR3400v2 device after the boot, until
he turns on GPIO #21 manually through sysfs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2170
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Eric Bohlman <ericbohlman@gmail.com>
Tested-by: Eric Bohlman <ericbohlman@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Paul Burton <paul.burton@mips.com>
|
|
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
|
|
1) Fix reset button support which is active *high*
2) Specify LEDs colors
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
|
|
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we never had any device registered for the SoC. This resulted in
some small issues that we kept ignoring like:
1) Not working GPIOLIB_IRQCHIP (gpiochip_irqchip_add_key() failing)
2) Lack of proper tree in the /sys/devices/
3) mips_dma_alloc_coherent() silently handling empty coherent_dma_mask
Kernel 4.19 came with a lot of DMA changes and caused a regression on
bcm47xx. Starting with the commit f8c55dc6e828 ("MIPS: use generic dma
noncoherent ops for simple noncoherent platforms") DMA coherent
allocations just fail. Example:
[ 1.114914] bgmac_bcma bcma0:2: Allocation of TX ring 0x200 failed
[ 1.121215] bgmac_bcma bcma0:2: Unable to alloc memory for DMA
[ 1.127626] bgmac_bcma: probe of bcma0:2 failed with error -12
[ 1.133838] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
The bgmac driver also triggers a WARNING:
[ 0.959486] ------------[ cut here ]------------
[ 0.964387] WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 bgmac_enet_probe+0x1b4/0x5c4
[ 0.973751] Modules linked in:
[ 0.976913] CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.9 #0
[ 0.982750] Stack : 804a0000 804597c4 00000000 00000000 80458fd8 8381bc2c 838282d4 80481a47
[ 0.991367] 8042e3ec 00000001 804d38f0 00000204 83980000 00000065 8381bbe0 6f55b24f
[ 0.999975] 00000000 00000000 80520000 00002018 00000000 00000075 00000007 00000000
[ 1.008583] 00000000 80480000 000ee811 00000000 00000000 00000000 80432c00 80248db8
[ 1.017196] 00000009 00000204 83980000 803ad7b0 00000000 801feeec 00000000 804d0000
[ 1.025804] ...
[ 1.028325] Call Trace:
[ 1.030875] [<8000aef8>] show_stack+0x58/0x100
[ 1.035513] [<8001f8b4>] __warn+0xe4/0x118
[ 1.039708] [<8001f9a4>] warn_slowpath_null+0x48/0x64
[ 1.044935] [<80248db8>] bgmac_enet_probe+0x1b4/0x5c4
[ 1.050101] [<802498e0>] bgmac_probe+0x558/0x590
[ 1.054906] [<80252fd0>] bcma_device_probe+0x38/0x70
[ 1.060017] [<8020e1e8>] really_probe+0x170/0x2e8
[ 1.064891] [<8020e714>] __driver_attach+0xa4/0xec
[ 1.069784] [<8020c1e0>] bus_for_each_dev+0x58/0xb0
[ 1.074833] [<8020d590>] bus_add_driver+0xf8/0x218
[ 1.079731] [<8020ef24>] driver_register+0xcc/0x11c
[ 1.084804] [<804b54cc>] bgmac_init+0x1c/0x44
[ 1.089258] [<8000121c>] do_one_initcall+0x7c/0x1a0
[ 1.094343] [<804a1d34>] kernel_init_freeable+0x150/0x218
[ 1.099886] [<803a082c>] kernel_init+0x10/0x104
[ 1.104583] [<80005878>] ret_from_kernel_thread+0x14/0x1c
[ 1.110107] ---[ end trace f441c0d873d1fb5b ]---
This patch setups a "struct device" (and passes it to the bcma) which
allows fixing all the mentioned problems. It'll also require a tiny bcma
patch which will follow through the wireless tree & its maintainer.
Fixes: f8c55dc6e828 ("MIPS: use generic dma noncoherent ops for simple noncoherent platforms")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.19+
|
|
Setting GPIO 21 high seems to be required to enable power to USB ports
on the WNDR3400v3. As there is already similar code for WNR3500L,
make the existing USB power GPIO code generic and use that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20259/
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
|
|
This reverts commit 2a027b47dba6 ("MIPS: BCM47XX: Enable 74K Core
ExternalSync for PCIe erratum").
Enabling ExternalSync caused a regression for BCM4718A1 (used e.g. in
Netgear E3000 and ASUS RT-N16): it simply hangs during PCIe
initialization. It's likely that BCM4717A1 is also affected.
I didn't notice that earlier as the only BCM47XX devices with PCIe I
own are:
1) BCM4706 with 2 x 14e4:4331
2) BCM4706 with 14e4:4360 and 14e4:4331
it appears that BCM4706 is unaffected.
While BCM5300X-ES300-RDS.pdf seems to document that erratum and its
workarounds (according to quotes provided by Tokunori) it seems not even
Broadcom follows them.
According to the provided info Broadcom should define CONF7_ES in their
SDK's mipsinc.h and implement workaround in the si_mips_init(). Checking
both didn't reveal such code. It *could* mean Broadcom also had some
problems with the given workaround.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Michael Marley <michael@michaelmarley.com>
Patchwork: https://patchwork.linux-mips.org/patch/20032/
URL: https://bugs.openwrt.org/index.php?do=details&task_id=1688
Cc: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
|
|
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19461/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
This struct variable is used during init only. It gets passed to the
gpio_led_register_device() which creates its own data copy. That allows
using __initdata and saving some minimal amount of memory.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18928/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
This adds support for detecting this model board and registers some LEDs
and buttons.
There are two uncommon things regarding this device:
1) It can use two different "board_id" ID values.
Unit I have uses "U12H139T00_NETGEAR" value. This magic is also used
in firmware file header. There are two reports (one from an OpenWrt
user) of a different "U12H139T50_NETGEAR" magic though.
2) Power LEDs share GPIOs with buttons.
Amber one seems to share GPIO 2 with WPS button and green one seems
to share GPIO 3 with reset button. It remains unknown how to support
them and handle buttons at the same time. For that reason they aren't
added to the list of supported LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19004/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The original patch submitted for support of the Luxul XWR-1750 used a
non-standard button handler for the reset button. This patch will allow
using the standard KEY_RESTART
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18981/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Some Luxul devices use PCIe connected GPIO LEDs that are not available
until the PCI subsytem and its drivers load. Using the same array for
these LEDs would block registering any LEDs until all GPIOs become
available. This may be undesired behavior as some LEDs should be
available as early as possible (e.g. system status LED). This patch will
allow registering available LEDs while deferring these PCIe GPIO
connected 'extra' LEDs until they become available.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18952/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Enable ZBOOT support. The WRT54GL router's bootloader limits kernel
size to 3 MB with the normal load address, which is a bit challenging
vmlinux size with modern Linux. A compressed kernel allows booting
much bigger kernels.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18492/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
|
|
The WLAN LED on the Linksys WRT54GSv1 is active low, but the software
treats it as active high. Fix the inverted logic.
Fixes: 7bb26b169116 ("MIPS: BCM47xx: Fix LEDs on WRT54GS V1.0")
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Looks-ok-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.17+
Patchwork: https://patchwork.linux-mips.org/patch/16071/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Asus WL-500W buttons are active high, but the software treats them
as active low. Fix the inverted logic.
Fixes: 3be972556fa1 ("MIPS: BCM47XX: Import buttons database from OpenWrt")
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14.x-
Patchwork: https://patchwork.linux-mips.org/patch/15295/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
So far only Luxul XWR-1750 router was supported. This adds a set of
other Luxul devices based on BCM47XX. It's a standard support for LEDs
and buttons.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13933/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
common place. We already have bcm47xx_nvram in firmware path and SPROM
should fit there as well.
This driver is responsible for parsing SoC configuration data into a
struct shared between ssb and bcma buses.
This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0
(ARCH_BCM_5301X).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
|
|
BCM47XX platform has specific PCI setup because all buses share the same
domain. It's different e.g. on ARM ARCH_BCM_5301X where each PCI bus
gets its own domain (they are handled by iProc PCIe controller driver).
As we want to make SPROM driver more generic, let's add an exception for
BCM47xx. It was tested on BCM4706 (MIPS) and BCM4708A0 (ARM).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11969/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There is code in ssb fetching "invariants" that is basically a set of
board specific data. Every host requires its own implementation of
reading function. In ssb we have support for PCI, PCMCIA & SDIO.
For some (historical?) reason code reading "invariants" for SoC was
placed in arch code and provided by a callback. This is not needed
nowadays, so lets move that into ssb. This way we keep all "invariants"
functions in a single module making code cleaner.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
|
|
This drops another symbol dependency between setup.c and sprom.c which
will allow us to make SPROM code a separated module (and share it with
ARM).
Patch tested on Linksys WRT300N V1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11360/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There are still few left:
1) Most of them about lines over 80 chars (increased readability exception)
2) Wrong parsing of preprocessor macros
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/11356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
To support (extract) SPROM on Broadcom ARM devices we should separate
SPROM code and make it a separated module. We won't want to export
bcm47xx_fill_sprom symbol so we should support SoC SPROM in the standard
fallback function and then modify ssb to use it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This allows saving a little of space when not using ssb on Broadcom SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
|
|
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10898/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the big SPROM cleanup moving code to the bcm47xx_sprom_fill_auto
we ended up with few tiny functions, two of them being identical. Let's
get rid of these [12]-liners.
This also stops extracting higher SPROM revisions as revision 1. Now we
have that function nicely handling revisions we don't need it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10569/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
After Broadcom switched from MIPS to ARM for their home routers we need
to have NVRAM driver in some common place (not arch/mips/). As explained
in Kconfig, this driver is responsible for parsing SoC configuration
data that is passed to the kernel in flash from the bootloader firmware
called "CFE".
We were thinking about putting it in bus directory, however there are
two possible buses for MIPS: drivers/ssb/ and drivers/bcma/. So this
won't fit there and this is why I would like to move this driver to the
drivers/firmware/.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mike Waychison <mikew@google.com>
Cc: Roy Franz <roy.franz@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/10544/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
SoC may have non-Broadcom PCI device attached or one may want to use
totally different PCI driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10537/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This simplifies code just a bit (also maybe makes it a bit more
intuitive?) and will allow us to stop storing header. Right now we copy
whole NVRAM including its header to the internal buffer. It is not
needed to store a header as we don't access all these details like CRC,
flags, etc. The next improvement that should follow is copying only the
real contents.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/10535/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Host platforms such as routers supported by OpenWrt can
support NVRAM reading directly from internal NVRAM store.
The brcmfmac for one requires the complete nvram contents
to select what needs to be sent to wireless device.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10093/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Dan Haab <dhaab@luxul.com>
Patchwork: https://patchwork.linux-mips.org/patch/9831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We removed __cpuinit support (leaving no-op stubs) quite some time ago.
However a few more crept in as of commit 6ee1d93455384cef8a0426effe85da2
("MIPS: BCM47XX: Detect more then 128 MiB of RAM (HIGHMEM)")
Since we want to clobber the stubs soon, get this removed now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Extra bcma buses may be totally different models, see following dump:
boardtype=0x0646
pci/1/1/boardtype=0x0545
pci/2/1/boardtype=0x62b
We need to detect them properly to allow drivers apply some board
specific hacks.
[ralf@linux-mips.org: folded in Rafal's fix.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10028/
Patchwork: https://patchwork.linux-mips.org/patch/10048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
New devices may have more than 1 Ethernet core (device). We should
extract info about them to make it available to Ethernet drivers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Ian Kent <raven@themaw.net>
Patchwork: https://patchwork.linux-mips.org/patch/10027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
For years we planned to get rid of old u16 fields, let's start doing it
with MIPS code. This process will take some time, it requires doing the
same in ssb/bcma and then switching all drivers to new fields. This will
be handled in separated patches submitted to appropriate trees.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/10026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
First of all it shouldn't modify copied NVRAM just to make sure it can
loop over all entries. It's enough to just compare current position
pointer with the end of buffer address.
Secondly buffer is guaranteed to be \0 ended, so we don't need strnchr.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Ian Kent <raven@themaw.net>
Patchwork: https://patchwork.linux-mips.org/patch/10032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This will simplify reading its contents.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Ian Kent <raven@themaw.net>
Patchwork: https://patchwork.linux-mips.org/patch/10031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
|
|
Since the day of adding this code it was broken. We were iterating over
a wrong array and checking for wrong NVRAM entry.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/9654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
