| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
"Several critical linear p2m fixes that prevented some hosts from
booting"
* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: properly retrieve NMI reason
xen: check for zero sized area when invalidating memory
xen: use correct type for physical addresses
xen: correct race in alloc_p2m_pmd()
xen: correct error for building p2m list on 32 bits
x86/xen: avoid freeing static 'name' when kasprintf() fails
x86/xen: add extra memory for remapped frames during setup
x86/xen: don't count how many PFNs are identity mapped
x86/xen: Free bootmem in free_p2m_page() during early boot
x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()
|
|
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
When converting a pfn to a physical address be sure to use 64 bit
wide types or convert the physical address to a pfn if possible.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
|
|
There was another report of a boot failure with a #GP fault in the
uncore SBOX initialization. The earlier work around was not enough
for this system.
The boot was failing while trying to initialize the third SBOX.
This patch detects parts with only two SBOXes and limits the number
of SBOX units to two there.
Stable material, as it affects boot problems on 3.18.
Tested-by: Andreas Oehler <andreas@oehler-net.de>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1420583675-9163-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Perf reports user regs for kernel-mode samples so that samples can
be backtraced through user code. The old code was very broken in
syscall context, resulting in useless backtraces.
The new code, in contrast, is still dangerously racy, but it should
at least work most of the time.
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: chenggang.qcg@taobao.com
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/243560c26ff0f739978e2459e203f6515367634d.1420396372.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On x86_64, at least, task_pt_regs may be only partially initialized
in many contexts, so x86_64 should not use it without extra care
from interrupt context, let alone NMI context.
This will allow x86_64 to override the logic and will supply some
scratch space to use to make a cleaner copy of user regs.
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: chenggang.qcg@taobao.com
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jean Pihet <jean.pihet@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/e431cd4c18c2e1c44c774f10758527fb2d1025c4.1420396372.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Stephane reported that the PEBS fixup was broken by the recent commit to
the instruction decoder. The thing had an off-by-one which resulted in
not being able to decode the last instruction and always bail.
Reported-by: Stephane Eranian <eranian@google.com>
Fixes: 6ba48ff46f76 ("x86: Remove arbitrary instruction size limit in instruction decoder")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org # 3.18
Cc: <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Liang Kan <kan.liang@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20141216104614.GV3337@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are an ACPI device power management initialization fix (-stable
material), two commits renaming stuff in the ACPI processor driver to
make it more suitable for ARM64 processors and a new ACPI backlight
blacklist entry.
Specifics:
- Fix ACPI power management intialization for device objects
corresponding to devices that are not present at the init time (the
_STA control method returns 0 for them) and therefore should not be
regarded as power manageable (Rafael J Wysocki).
- Rename a structure field and two functions used by the ACPI
processor driver to make them less tied to architectures that use
APICs (both x86 and ia64) and more suitable for ARM64 processors
(Hanjun Guo).
- Add a disable_native_backlight quirk for Dell XPS15 L521X designed
in an unusual way preventing native backlight from working on that
machine (Hans de Goede)"
* tag 'pm+acpi-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add disable_native_backlight quirk for Dell XPS15 L521X
ACPI / processor: Rename acpi_(un)map_lsapic() to acpi_(un)map_cpu()
ACPI / processor: Convert apic_id to phys_id to make it arch agnostic
ACPI / PM: Fix PM initialization for devices that are not present
|
|
Pull crypto fixes from Herbert Xu:
"This fixes a build problem with sha-mb with old toolchains and an
implementation bug in the ctr(aes)/by8 branch of aesni-intel that's
enabled when AVX is available"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha-mb - Add avx2_supported check.
crypto: aesni - fix "by8" variant for 128 bit keys
|
|
In case kasprintf() fails in xen_setup_timer() we assign name to the
static string "<timer kasprintf failed>". We, however, don't check
that fact before issuing kfree() in xen_teardown_timer(), kernel is
supposed to crash with 'kernel BUG at mm/slub.c:3341!'
Solve the issue by making name a fixed length string inside struct
xen_clock_event_device. 16 bytes should be enough.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
If the non-RAM regions in the e820 memory map are larger than the size
of the initial balloon, a BUG was triggered as the frames are remaped
beyond the limit of the linear p2m. The frames are remapped into the
initial balloon area (xen_extra_mem) but not enough of this is
available.
Ensure enough extra memory regions are added for these remapped
frames.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
|
|
This accounting is just used to print a diagnostic message that isn't
very useful.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
|
|
With recent changes in p2m we now have legitimate cases when
p2m memory needs to be freed during early boot (i.e. before
slab is initialized).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
* acpi-pm:
ACPI / PM: Fix PM initialization for devices that are not present
* acpi-processor:
ACPI / processor: Rename acpi_(un)map_lsapic() to acpi_(un)map_cpu()
ACPI / processor: Convert apic_id to phys_id to make it arch agnostic
* acpi-video:
ACPI / video: Add disable_native_backlight quirk for Dell XPS15 L521X
|
|
acpi_map_lsapic() will allocate a logical CPU number and map it to
physical CPU id (such as APIC id) for the hot-added CPU, it will also
do some mapping for NUMA node id and etc, acpi_unmap_lsapic() will
do the reverse.
We can see that the name of the function is a little bit confusing and
arch (IA64) dependent so rename them as acpi_(un)map_cpu() to make arch
agnostic and explicit.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch fixes this allyesconfig target build error with older
binutils.
LD arch/x86/crypto/built-in.o
ld: arch/x86/crypto/sha-mb/built-in.o: No such file: No such file or directory
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Vinson Lee <vlee@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The "by8" counter mode optimization is broken for 128 bit keys with
input data longer than 128 bytes. It uses the wrong key material for
en- and decryption.
The key registers xkey0, xkey4, xkey8 and xkey12 need to be preserved
in case we're handling more than 128 bytes of input data -- they won't
get reloaded after the initial load. They must therefore be (a) loaded
on the first iteration and (b) be preserved for the latter ones. The
implementation for 128 bit keys does not comply with (a) nor (b).
Fix this by bringing the implementation back to its original source
and correctly load the key registers and preserve their values by
*not* re-using the registers for other purposes.
Kudos to James for reporting the issue and providing a test case
showing the discrepancies.
Reported-by: James Yonan <james@openvpn.net>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit a074335a370e ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a370e ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull VDSO fix from Andy Lutomirski:
"This is hopefully the last vdso fix for 3.19. It should be very
safe (it just adds a volatile).
I don't think it fixes an actual bug (the __getcpu calls in the
pvclock code may not have been needed in the first place), but
discussion on that point is ongoing.
It also fixes a big performance issue in 3.18 and earlier in which
the lsl instructions in vclock_gettime got hoisted so far up the
function that they happened even when the function they were in was
never called. n 3.19, the performance issue seems to be gone due to
the whims of my compiler and some interaction with a branch that's
now gone.
I'll hopefully have a much bigger overhaul of the pvclock code
for 3.20, but it needs careful review."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.
Cc: stable@vger.kernel.org
Fixes: 7a2e8aaf0f6873b47bc2347f216ea5b0e4c258ab
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The commit 34a1cd60d17f, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In Linux 3.18 and below, GCC hoists the lsl instructions in the
pvclock code all the way to the beginning of __vdso_clock_gettime,
slowing the non-paravirt case significantly. For unknown reasons,
presumably related to the removal of a branch, the performance issue
is gone as of
e76b027e6408 x86,vdso: Use LSL unconditionally for vgetcpu
but I don't trust GCC enough to expect the problem to stay fixed.
There should be no correctness issue, because the __getcpu calls in
__vdso_vlock_gettime were never necessary in the first place.
Note to stable maintainers: In 3.18 and below, depending on
configuration, gcc 4.9.2 generates code like this:
9c3: 44 0f 03 e8 lsl %ax,%r13d
9c7: 45 89 eb mov %r13d,%r11d
9ca: 0f 03 d8 lsl %ax,%ebx
This patch won't apply as is to any released kernel, but I'll send a
trivial backported version if needed.
Fixes: 51c19b4f5927 x86: vdso: pvclock gettime support
Cc: stable@vger.kernel.org # 3.8+
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
Commit 9def39be4e96 ("x86: Support compiling out human-friendly
processor feature names") made two source file targets
conditional. Such conditional targets will not be cleaned
automatically by make mrproper.
Fix by adding explicit clean-files targets for the two files.
Fixes: 9def39be4e96 ("x86: Support compiling out human-friendly processor feature names")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/1419335863-10608-1-git-send-email-bjorn@mork.no
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Chocked while compiling linux with dash shell instead of bash
shell. See:
http://pubs.opengroup.org/onlinepubs/9699919799/utilities/test.html
Signed-off-by: Sylvain BERTRAND <sylvain.bertrand@gmail.com>
Link: http://lkml.kernel.org/r/20141223123912.GA1386@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The old scheme can lead to failure in certain cases - the
problem is that after bumping step_size the next (non-final)
iteration is only guaranteed to make available a memory block
the size of what step_size was before. E.g. for a memory block
[0,3004600000) we'd have:
iter start end step amount
1 3004400000 30045fffff 2M 2M
2 3004000000 30043fffff 64M 4M
3 3000000000 3003ffffff 2G 64M
4 2000000000 2fffffffff 64G 64G
Yet to map 64G with 4k pages (as happens e.g. under PV Xen) we
need slightly over 128M, but the first three iterations made
only about 70M available.
The condition (new_mapped_ram_size > mapped_ram_size) for
bumping step_size is just not suitable. Instead we want to bump
it when we know we have enough memory available to cover a block
of the new step_size. And rather than making that condition more
complicated than needed, simply adjust step_size by the largest
possible factor we know we can cover at that point - which is
shifting it left by one less than the difference between page
table level shifts. (Interestingly the original STEP_SIZE_SHIFT
definition had a comment hinting at that having been the
intention, just that it should have been PUD_SHIFT-PMD_SHIFT-1
instead of (PUD_SHIFT-PMD_SHIFT)/2, and of course for non-PAE
32-bit we can't really use these two constants as they're equal
there.)
Furthermore the comment in get_new_step_size() didn't get
updated when the bottom-down mapping logic got added. Yet while
an overflow (flushing step_size to zero) of the shift doesn't
matter for the top-down method, it does for bottom-up because
round_up(x, 0) = 0, and an upper range boundary of zero can't
really work well.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/54945C1E020000780005114E@mail.emea.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There is no reason for having it and, with commit 250a1ac685f1 ("x86,
smpboot: Remove pointless preempt_disable() in
native_smp_prepare_cpus()"), it prevents HVM guests from booting.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull a VDSO fix from Andy Lutomirski:
"One vdso fix for a longstanding ASLR bug that's been in the news lately.
The vdso base address has always been randomized, and I don't think there's
anything particularly wrong with the range over which it's randomized,
but the implementation seems to have been buggy since the very beginning.
This fixes the implementation to remove a large bias that caused a small
fraction of possible vdso load addresess to be vastly more likely than
the rest of the possible addresses."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The theory behind vdso randomization is that it's mapped at a random
offset above the top of the stack. To avoid wasting a page of
memory for an extra page table, the vdso isn't supposed to extend
past the lowest PMD into which it can fit. Other than that, the
address should be a uniformly distributed address that meets all of
the alignment requirements.
The current algorithm is buggy: the vdso has about a 50% probability
of being at the very end of a PMD. The current algorithm also has a
decent chance of failing outright due to incorrect handling of the
case where the top of the stack is near the top of its PMD.
This fixes the implementation. The paxtest estimate of vdso
"randomisation" improves from 11 bits to 18 bits. (Disclaimer: I
don't know what the paxtest code is actually calculating.)
It's worth noting that this algorithm is inherently biased: the vdso
is more likely to end up near the end of its PMD than near the
beginning. Ideally we would either nix the PMD sharing requirement
or jointly randomize the vdso and the stack to reduce the bias.
In the mean time, this is a considerable improvement with basically
no risk of compatibility issues, since the allowed outputs of the
algorithm are unchanged.
As an easy test, doing this:
for i in `seq 10000`
do grep -P vdso /proc/self/maps |cut -d- -f1
done |sort |uniq -d
used to produce lots of output (1445 lines on my most recent run).
A tiny subset looks like this:
7fffdfffe000
7fffe01fe000
7fffe05fe000
7fffe07fe000
7fffe09fe000
7fffe0bfe000
7fffe0dfe000
Note the suspicious fe000 endings. With the fix, I get a much more
palatable 76 repeated addresses.
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"This contains a single TLS ABI validation fix from Andy Lutomirski"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Don't validate lm in set_thread_area() after all
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes and cleanups from Ingo Molnar:
"A kernel fix plus mostly tooling fixes, but also some tooling
restructuring and cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf: Fix building warning on ARM 32
perf symbols: Fix use after free in filename__read_build_id
perf evlist: Use roundup_pow_of_two
tools: Adopt roundup_pow_of_two
perf tools: Make the mmap length autotuning more robust
tools: Adopt rounddown_pow_of_two and deps
tools: Adopt fls_long and deps
tools: Move bitops.h from tools/perf/util to tools/
tools: Introduce asm-generic/bitops.h
tools lib: Move asm-generic/bitops/find.h code to tools/include and tools/lib
tools: Whitespace prep patches for moving bitops.h
tools: Move code originally from asm-generic/atomic.h into tools/include/asm-generic/
tools: Move code originally from linux/log2.h to tools/include/linux/
tools: Move __ffs implementation to tools/include/asm-generic/bitops/__ffs.h
perf evlist: Do not use hard coded value for a mmap_pages default
perf trace: Let the perf_evlist__mmap autosize the number of pages to use
perf evlist: Improve the strerror_mmap method
perf evlist: Clarify sterror_mmap variable names
perf evlist: Fixup brown paper bag on "hint" for --mmap-pages cmdline arg
perf trace: Provide a better explanation when mmap fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
|
|
Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
|
|
It turns out that there's a lurking ABI issue. GCC, when
compiling this in a 32-bit program:
struct user_desc desc = {
.entry_number = idx,
.base_addr = base,
.limit = 0xfffff,
.seg_32bit = 1,
.contents = 0, /* Data, grow-up */
.read_exec_only = 0,
.limit_in_pages = 1,
.seg_not_present = 0,
.useable = 0,
};
will leave .lm uninitialized. This means that anything in the
kernel that reads user_desc.lm for 32-bit tasks is unreliable.
Revert the .lm check in set_thread_area(). The value never did
anything in the first place.
Fixes: 0e58af4e1d21 ("x86/tls: Disallow unusual TLS segments")
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # Only if 0e58af4e1d21 is backported
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/d7875b60e28c512f6a6fc0baf5714d58e7eaadbb.1418856405.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
ACCESS_ONCE does not work reliably on non-scalar types. For
example gcc 4.6 and 4.7 might remove the volatile tag for such
accesses during the SRA (scalar replacement of aggregates) step
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145)
Change the gup code to replace ACCESS_ONCE with READ_ONCE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
ACCESS_ONCE does not work reliably on non-scalar types. For
example gcc 4.6 and 4.7 might remove the volatile tag for such
accesses during the SRA (scalar replacement of aggregates) step
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145)
Change the spinlock code to replace ACCESS_ONCE with READ_ONCE.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
They are not used anymore by IA64, move them away.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
My commit 26178ec11ef3 ("x86: mm: consolidate VM_FAULT_RETRY handling")
had a really stupid typo: the FAULT_FLAG_USER bit is in the 'flags'
variable, not the 'fault' variable. Duh,
The one silver lining in this is that Dave finding this at least
confirms that trinity actually triggers this special path easily, in a
way normal use does not.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull additional xen update from David Vrabel:
"Xen: additional features for 3.19-rc0
- Linear p2m for x86 PV guests which simplifies the p2m code,
improves performance and will allow for > 512 GB PV guests in the
future.
A last-minute, configuration specific issue was discovered with this
change which is why it was not included in my previous pull request.
This is now been fixed and tested"
* tag 'stable/for-linus-3.19-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: switch to post-init routines in xen mmu.c earlier
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen: annotate xen_set_identity_and_remap_chunk() with __init
xen: introduce helper functions to do safe read and write accesses
xen: Speed up set_phys_to_machine() by using read-only mappings
xen: switch to linear virtual mapped sparse p2m list
xen: Hide get_phys_to_machine() to be able to tune common path
x86: Introduce function to get pmd entry pointer
xen: Delay invalidating extra memory
xen: Delay m2p_override initialization
xen: Delay remapping memory of pv-domain
xen: use common page allocation function in p2m.c
xen: Make functions static
xen: fix some style issues in p2m.c
|
|
Use helpers to access irq_cfg data structure associated with IRQ,
instead of accessing irq_data->chip_data directly. Later we can
rewrite those helpers to support hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-17-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Now we have splitted functions to support MSI and HT_IRQ into vector.c,
and they have no dependency on IOAPIC any more. So change Kconfig files
to make MSI and HT_IRQ independent of X86_IO_APIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414397531-28254-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Move IRQ initialization routines from io_apic.c into vector.c,
preparing for enabling hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1414397531-28254-15-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Clean up code by moving IOAPIC related declarations from hw_irq.h into
io_apic.h.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Aubrey <aubrey.li@linux.intel.com>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
