| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
|
|
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
|
|
commit 93f378883cecb9dcb2cf5b51d9d24175906659da
"Fix ia64 build errors (fallout from system.h disintegration)"
introduced arch/ia64/include/asm/cmpxchg.h as a temporary
build fix and stated:
"... leave the migration of xchg() and cmpxchg() to this new
header file for a future patch."
Migrate the appropriate chunks from asm/intrinsics.h and fix
the whitespace issues in the migrated chunk.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit ec2212088c42ff7d1362629ec26dda4f3e8bdad3
"Disintegrate asm/system.h for Alpha"
combined with commit b4816afa3986704d1404fc48e931da5135820472
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the alpha arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Some minor whitespace fixups were done on the block of code that
created the new file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Use correct byte-sized register constraint in __add()
x86: Use correct byte-sized register constraint in __xchg_op()
x86: vsyscall: Use NULL instead 0 for a pointer argument
|
|
Pull irqdomain bug fixes from Grant Likely:
"This branch fixes a bug in irq_create_mapping() where an error return
from irq_alloc_desc_from() gets ignored.
It also removes irq_virq_count to fix a bug on powerpc where the
irqdomain code does not find irqs allocated above the CONFIG_NR_IRQS
boundary.
The remaining patches get rid of an completely pointless export and
fix some minor bugs in the irqdomain debug output."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irq_domain: Move irq_virq_count into NOMAP revmap
irqdomain: Fix debugfs formatting
irq_domain: correct the debugfs file name
irq: Kill pointless irqd_to_hw export
irq/irq_domain: Quit ignoring error returns from irq_alloc_desc_from().
|
|
This patch replaces the old global setting of irq_virq_count that is only
used by the NOMAP mapping and instead uses a revmap_data property so that
the maximum NOMAP allocation can be set per NOMAP irq_domain.
There is exactly one user of irq_virq_count in-tree right now: PS3.
Also, irq_virq_count is only useful for the NOMAP mapping. So,
instead of having a single global irq_virq_count values, this change
drops it entirely and added a max_irq argument to irq_domain_add_nomap().
That makes it a property of an individual nomap irq domain instead of
a global system settting.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Fixes for two nasty regression affecting powerpc in 3.4."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix typo in runlatch code
powerpc: Fix page fault with lockdep regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fixes from Chris Metcalf:
"This is one important change from Srivatsa Bhat that got dropped when
I put together my pull request for -rc2, plus a trivial change to
remove a compiler warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: avoid unused variable warning in proc.c for tilegx
tile/CPU hotplug: Add missing call to notify_cpu_starting()
|
|
Until we push the unaligned access support for tilegx, it's silly
to have arch/tile/kernel/proc.c generate a warning about an unused
variable. Extend the #ifdef to cover all the code and data for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
This merges the 32- and 64-bit versions of the x86 strncpy_from_user()
by just rewriting it in C rather than the ancient inline asm versions
that used lodsb/stosb and had been duplicated for (trivial) differences
between the 32-bit and 64-bit versions.
While doing that, it also speeds them up by doing the accesses a word at
a time. Finally, the new routines also properly handle the case of
hitting the end of the address space, which we have never done correctly
before (fs/namei.c has a hack around it for that reason).
Despite all these improvements, it actually removes more lines than it
adds, due to the de-duplication. Also, we no longer export (or define)
the legacy __strncpy_from_user() function (that was defined to not do
the user permission checks), since it's not actually used anywhere, and
the user address space checks are built in to the new code.
Other architecture maintainers have been notified that the old hack in
fs/namei.c will be going away in the 3.5 merge window, in case they
copied the x86 approach of being a bit cavalier about the end of the
address space.
Cc: linux-arch@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin" <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It makes no sense to export this trivial function. Make it a static inline
instead.
This patch also drops virq_to_hw from arch/c6x since it is unused by that
architecture.
v2: Move irq_hw_number_t into types.h to fix ARM build failure
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit fe1952fc0afb9a2e4c79f103c08aef5d13db1873
"powerpc: Rework runlatch code" has a nasty typo
where it uses "TLF_RUNLATCH" instead of "_TLF_RUNLATCH"
(bit number instead of bit mask), causing some flags to
be potentially lost such as _TLF_RESTORE_SIGMASK
(Brown paper bag for me ! We should be able to make
that break at compile time with a bit of magic, any
volunteer ?)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Pull sparc fixes from David Miller:
1) Build fix for LEON, from Sam Ravnborg.
2) Make the sparc side changes that go along with the infrastructure to
retry faults when blocking on a disk transfer. From Kautuk Consul.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32,leon: fix leon build
sparc/mm/fault_32.c: Port OOM changes to do_sparc_fault
sparc/mm/fault_64.c: Port OOM changes to do_sparc64_fault
|
|
commit a546498f3bf9aac311c66f965186373aee2ca0b0
introduced a regression on 32-bit when irq tracing
is enabled by exposing an old bug in our irq tracing
code for exception entry.
The code would save and restore some GPRs around the
calls to the C lockdep code, however, it tries to be
too smart for its own good and restores some of the
GPRs from the exception frame (as saved there on
exception entry).
However, for page faults, we do replace those GPRs with
arguments to do_page_fault before we call transfer_to_handler
and so restoring from the exception frame is plain wrong in
this case.
This was fine as long as we didn't touch the interrupt state
when taking page fault, but when I started doing it, it would
trigger the lockdep calls and the bug.
This fixes it by cleaning up that code a bit. It did create
a small stack frame for the sake of backtraces, so let's
make it a bit bigger and use it to save and restore the
stuff we care about.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix the following gcc complain
arch/um/kernel/skas/mmu.c: In function 'uml_setup_stubs':
arch/um/kernel/skas/mmu.c:106:16: warning: unused variable 'pages' [-Wunused-variable]
Signed-Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
CC: dhowells@redhat.com
|
|
... rather than open-coding the 64bit versions. endian.h has those guys.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
while we can't just use -U$(SUBARCH), we still need to kill idiotic define
(implicit -Di386=1), both for SUBARCH=i386 and SUBARCH=x86/CONFIG_64BIT=n
builds.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
|
|
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
|
|
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
|
|
Similar to:
2ca052a x86: Use correct byte-sized register constraint in __xchg_op()
... the __add() macro also needs to use a "q" constraint in the
byte-sized case, lest we try to generate an illegal register.
Link: http://lkml.kernel.org/r/4F7A3315.501@goop.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Leigh Scott <leigh123linux@googlemail.com>
Cc: Thomas Reitmayr <treitmayr@devbase.at>
Cc: <stable@vger.kernel.org> v3.3
|
|
x86-64 can access the low half of any register, but i386 can only do
it with a subset of registers. 'r' causes compilation failures on i386,
but 'q' expresses the constraint properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Link: http://lkml.kernel.org/r/4F7A3315.501@goop.org
Reported-by: Leigh Scott <leigh123linux@googlemail.com>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org> v3.3
|
|
There is an extra and unnecessary call to smp_processor_id()
in cpu_bringup(). Remove it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
io-apic entries'
The above mentioned patch checks the IOAPIC and if it contains
-1, then it unmaps said IOAPIC. But under Xen we get this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
IP: [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
PGD 0
Oops: 0002 [#1] SMP
CPU 0
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.2.10-3.fc16.x86_64 #1 Dell Inc. Inspiron
1525 /0U990C
RIP: e030:[<ffffffff8134e51f>] [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
RSP: e02b: ffff8800d42cbb70 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000ffffffef RCX: 0000000000000001
RDX: 0000000000000040 RSI: 00000000ffffffef RDI: 0000000000000001
RBP: ffff8800d42cbb80 R08: ffff8800d6400000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffef
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000010
FS: 0000000000000000(0000) GS:ffff8800df5fe000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0:000000008005003b
CR2: 0000000000000040 CR3: 0000000001a05000 CR4: 0000000000002660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper/0 (pid: 1, threadinfo ffff8800d42ca000, task ffff8800d42d0000)
Stack:
00000000ffffffef 0000000000000010 ffff8800d42cbbe0 ffffffff8134f157
ffffffff8100a9b2 ffffffff8182ffd1 00000000000000a0 00000000829e7384
0000000000000002 0000000000000010 00000000ffffffff 0000000000000000
Call Trace:
[<ffffffff8134f157>] xen_bind_pirq_gsi_to_irq+0x87/0x230
[<ffffffff8100a9b2>] ? check_events+0x12+0x20
[<ffffffff814bab42>] xen_register_pirq+0x82/0xe0
[<ffffffff814bac1a>] xen_register_gsi.part.2+0x4a/0xd0
[<ffffffff814bacc0>] acpi_register_gsi_xen+0x20/0x30
[<ffffffff8103036f>] acpi_register_gsi+0xf/0x20
[<ffffffff8131abdb>] acpi_pci_irq_enable+0x12e/0x202
[<ffffffff814bc849>] pcibios_enable_device+0x39/0x40
[<ffffffff812dc7ab>] do_pci_enable_device+0x4b/0x70
[<ffffffff812dc878>] __pci_enable_device_flags+0xa8/0xf0
[<ffffffff812dc8d3>] pci_enable_device+0x13/0x20
The reason we are dying is b/c the call acpi_get_override_irq() is used,
which returns the polarity and trigger for the IRQs. That function calls
mp_find_ioapics to get the 'struct ioapic' structure - which along with the
mp_irq[x] is used to figure out the default values and the polarity/trigger
overrides. Since the mp_find_ioapics now returns -1 [b/c the IOAPIC is filled
with 0xffffffff], the acpi_get_override_irq() stops trying to lookup in the
mp_irq[x] the proper INT_SRV_OVR and we can't install the SCI interrupt.
The proper fix for this is going in v3.5 and adds an x86_io_apic_ops
struct so that platforms can override it. But for v3.4 lets carry this
work-around. This patch does that by providing a slightly different variant
of the fake IOAPIC entries.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
This patch silences the following sparse warning:
arch/x86/kernel/vsyscall_64.c:250:34:
warning: Using plain integer as NULL pointer
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: john.stultz@linaro.org
Link: http://lkml.kernel.org/r/1333306084-3776-1-git-send-email-emilgoode@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
|
|
To fix compile error:
drivers/usb/musb/blackfin.h:51:3: error: #error "Please use PIO mode in MUSB
driver on bf52x chip v0.0 and v0.1"
make[4]: *** [drivers/usb/musb/blackfin.o] Error 1
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
Add __gpio_get_value()/__gpio_set_value() to fix compile error if
CONFIG_GPIOLIB = n.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
This patch fix below compile error:
"bfin-uclinux-ld: L1 data A overflow!"
It is due to the recent lib/gen_crc32table.c change:
46c5801eaf86e83cb3a4142ad35188db5011fff0
crc32: bolt on crc32c
it added 8KiB more data to __cacheline_aligned which cause blackfin L1 data
cache overflow.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
|
|
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
|
|
As described in e6fa16ab9c1e ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f28f
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As described in e6fa16ab9c1e ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check for shared signals we're about to block.
Also, use the new helper function introduced in commit 5e6292c0f28f
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: EXYNOS: use chip_id reg in uncompress to select uart base phys
ARM: EXYNOS: fix CONFIG_DEBUG_LL
ARM: S3C24XX: fix missing common.h in mach-s3c24xx/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Note that this also contains a set of fixes that are not regressions
or oopses to properly deal with the smsc911x regulator issue.
Basically the regulators must be per board file as the regulators
can also come from drivers, such as twl4030. So it's best to dumb
down gpmc-smsc911x.c to not even care about the regulators.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: fix section mismatches in usb-host.c
ARM: OMAP2+: Fix omap2+ build error
ARM: OMAP2+: smsc911x: Add fixed board regulators
ARM: OMAP2+: smsc911x: Remove regulator support from gmpc-smsc911x
ARM: OMAP2+: smsc911x: Remove unused rate calculation
ARM: OMAP2+ smsc911x: Fix possible stale smsc911x flags
ARM: OMAP2+: smsc911x: Remove odd gpmc_cfg/board_data redirection
ARM: OMAP3+: fix oops triggered in omap_prcm_register_chain_handler(v1)
ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present
arm: omap3: pm34xx.c: Replace printk() with appropriate pr_*()
arm: omap3: pm34xx.c: Fix omap3_pm_init() error out paths
ARM: OMAP4: Workaround the OCP synchronisation issue with 32K synctimer.
ARM: OMAP4: prm: fix interrupt register offsets
ARM: OMAP: hwmod: Use sysc_fields->srst_shift and get rid of hardcoded SYSC_TYPE2_SOFTRESET_MASK
|
|
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
USB: ohci-at91: change maximum number of ports
USB: ohci-at91: rework and fix initialization
ARM: at91/dts: USB host vbus is active low
ARM: at91/USB host: specify and handle properly vbus_pin_active_low
USB: ohci-at91: fix vbus_pin_active_low handling
ARM: at91/at91sam9x5: add clkdev entries for DMA controllers
|
|
"Page ready" async PF can kick vcpu out of idle state much like IRQ.
We need to tell RCU about this.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Five fixes for bugs that have crept in to the powerpc KVM implementations.
These are all small simple patches that only affect arch/powerpc/kvm.
They come from the series that Alex Graf put together but which was too
late for the 3.4 merge window.
* tag 'powerpc-fixes' of git://github.com/paulusmack/linux:
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
vmx_set_cr0 is called from vcpu run context, therefore it expects
kvm->srcu to be held (for setting up the real-mode TSS).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Signed-off-by: Sasikantha babu <sasikanth.v19@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
