| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
|
|
Patches 7cba160ad "powernv/cpuidle: Redesign idle states management"
and 77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes: 7cba160ad789 ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454ddb9 ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The incorrect ordering of operations during cpu dlpar add results in invalid
affinity for the cpu being added. The ibm,associativity property in the
device tree is populated with all zeroes for the added cpu which results in
invalid affinity mappings and all cpus appear to belong to node 0.
This occurs because rtas configure-connector is called prior to making the
rtas set-indicator calls. Phyp does not assign affinity information
for a cpu until the rtas set-indicator calls are made to set the isolation
and allocation state.
Correct the order of operations to make the rtas set-indicator
calls (done in dlpar_acquire_drc) before calling rtas configure-connector.
Fixes: 1a8061c46c46 ("powerpc/pseries: Add kernel based CPU DLPAR handling")
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull kvm changes from Paolo Bonzini:
"Remove from guest code the handling of task migration during a pvclock
read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core scheduler
code"
[ The scheduler people really hated the migration notifiers, so this was
kind of required - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: pvclock: Really remove the sched notifier for cross-cpu migrations
kvm: x86: fix kvmclock update protocol
|
|
With commit d5efd9cc9cf2 ("arm64: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:
hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]
This patch fixes the name to that of the pmu node.
Fixes: d5efd9cc9cf2 (arm64: pmu: add support for interrupt-affinity property)
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This reverts commit feba40362b11341bee6d8ed58d54b896abbd9f84.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b11 ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
__dma_alloc() does a PAGE_ALIGN() on the passed in size argument before
doing anything else. __dma_free() does not. And because it doesn't, it is
possible to leak memory should size not be an integer multiple of PAGE_SIZE.
The solution is to add a PAGE_ALIGN() to __dma_free() like is done in
__dma_alloc().
Additionally, this patch removes a redundant PAGE_ALIGN() from
__dma_alloc_coherent(), since __dma_alloc_coherent() can only be called
from __dma_alloc(), which already does a PAGE_ALIGN() before the call.
Cc: stable@vger.kernel.org
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Load the PowerNV platform pci controller ops into pci controllers
after all the operations are loaded into the platform ops struct, not
before.
Otherwise we aren't actually setting the ops properly which can break
IO for some devices.
Fixes: 65ebf4b63 ("powerpc/powernv: Move controller ops from ppc_md to controller_ops")
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 34cb7954c0aa "Convert ICS mutex lock to spin lock" added an
include of asm/spinlock.h, which does not work in the SMP=n case.
It should instead include linux/spinlock.h
Fixes: 34cb7954c0aa ("KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock")
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile bugfix from Chris Metcalf:
"This just fixes a compiler warning from an old bug that only recently
started generating a warning"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use node_isset() on a nodemask_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"One additional new feature for 4.1, a new PRNG based on SHA-512 for
the zcrypt driver.
Two memory management related changes, the page table reallocation for
KVM is removed, and with file ptes gone the encoding of page table
entries is improved.
And three bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Introduce new SHA-512 based Pseudo Random Generator.
s390/mm: change swap pte encoding and pgtable cleanup
s390/mm: correct transfer of dirty & young bits in __pmd_to_pte
s390/bpf: add dependency to z196 features
s390/3215: free memory in error path
s390/kvm: remove delayed reallocation of page tables for KVM
kexec: allocate the kexec control page with KEXEC_CONTROL_MEMORY_GFP
|
|
The code accidentally used cpu_isset() previously in one place
(though properly node_isset() elsewhere).
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
|
|
This reverts commits 0a4e6be9ca17c54817cf814b4b5aa60478c6df27
and 80f7fdb1c7f0f9266421f823964fd1962681f6ce.
The task migration notifier was originally introduced in order to support
the pvclock vsyscall with non-synchronized TSC, but KVM only supports it
with synchronized TSC. Hence, on KVM the race condition is only needed
due to a bad implementation on the host side, and even then it's so rare
that it's mostly theoretical.
As far as KVM is concerned it's possible to fix the host, avoiding the
additional complexity in the vDSO and the (re)introduction of the task
migration notifier.
Xen, on the other hand, hasn't yet implemented vsyscall support at
all, so we do not care about its plans for non-synchronized TSC.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kvmclock spec says that the host will increment a version field to
an odd number, then update stuff, then increment it to an even number.
The host is buggy and doesn't do this, and the result is observable
when one vcpu reads another vcpu's kvmclock data.
There's no good way for a guest kernel to keep its vdso from reading
a different vcpu's kvmclock data, but we don't need to care about
changing VCPUs as long as we read a consistent data from kvmclock.
(VCPU can change outside of this loop too, so it doesn't matter if we
return a value not fit for this VCPU.)
Based on a patch by Radim Krčmář.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Buffers allocated by dma_alloc_coherent() are always zeroed on Alpha,
ARM (32bit), MIPS, PowerPC, x86/x86_64 and probably other architectures.
It turned out that some drivers rely on this 'feature'. Allocated buffer
might be also exposed to userspace with dma_mmap() call, so clearing it
is desired from security point of view to avoid exposing random memory
to userspace. This patch unifies dma_alloc_coherent() behavior on ARM64
architecture with other implementations by unconditionally zeroing
allocated buffer.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Since several interrupt controllers including GIC support both edge and
level triggered interrupts, it's useful to provide that information in
/proc/interrupts even on ARM64 similar to ARM and PPC.
This is based on Geert Uytterhoeven's commit 7c07005eea96 ("ARM: 8339/1:
Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 8053871d0f7f ("smp: Fix smp_call_function_single_async()
locking") introduced a call to smp_load_acquire() with a u16 argument,
but we only cared about u32 and u64 types in that function so far.
This resulted in a compiler warning fortunately, pointing at an
uninitialized use. Due to the implementation structure the compiler
misses that bug in the smp_store_release(), though.
Add the u16 and u8 variants using ldarh/stlrh and ldarb/stlrb,
respectively. Together with the compiletime_assert_atomic_type() check
this should cover all cases now.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.
Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.
This was exposed by a recent vDSO cleanup.
Fixes: e7d6eefaaa44 x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
|
|
Pull crypto fixes from Herbert Xu:
"This push fixes a build problem with img-hash under non-standard
configurations and a serious regression with sha512_ssse3 which can
lead to boot failures"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
crypto: x86/sha512_ssse3 - fixup for asm function prototype change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- fix for mm_dec_nr_pmds() from Scott.
- fixes for oopses seen with KVM + THP from Aneesh.
- build fixes from Aneesh & Shreyas.
* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
powerpc/mm/thp: Return pte address if we find trans_splitting.
powerpc/mm/thp: Make page table walk safe against thp split/collapse
KVM: PPC: Remove page table walk helpers
KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()
|
|
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
|
|
Pull slave-dmaengine updates from Vinod Koul:
- new drivers for:
- Ingenic JZ4780 controller
- APM X-Gene controller
- Freescale RaidEngine device
- Renesas USB Controller
- remove device_alloc_chan_resources dummy handlers
- sh driver cleanups for peri peri and related emmc and asoc patches
as well
- fixes and enhancements spread over the drivers
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (59 commits)
dmaengine: dw: don't prompt for DW_DMAC_CORE
dmaengine: shdmac: avoid unused variable warnings
dmaengine: fix platform_no_drv_owner.cocci warnings
dmaengine: pch_dma: fix memory leak on failure path in pch_dma_probe()
dmaengine: at_xdmac: unlock spin lock before return
dmaengine: xgene: devm_ioremap() returns NULL on error
dmaengine: xgene: buffer overflow in xgene_dma_init_channels()
dmaengine: usb-dmac: Fix dereferencing freed memory 'desc'
dmaengine: sa11x0: report slave capabilities to upper layers
dmaengine: vdma: Fix compilation warnings
dmaengine: fsl_raid: statify fsl_re_chan_probe
dmaengine: Driver support for FSL RaidEngine device.
dmaengine: xgene_dma_init_ring_mngr() can be static
Documentation: dma: Add documentation for the APM X-Gene SoC DMA device DTS binding
arm64: dts: Add APM X-Gene SoC DMA device and DMA clock DTS nodes
dmaengine: Add support for APM X-Gene SoC DMA engine driver
dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver
dmaengine: renesas,usb-dmac: Add device tree bindings documentation
dmaengine: edma: fixed wrongly initialized data parameter to the edma callback
dmaengine: ste_dma40: fix implicit conversion
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
|
|
Pull ARM fixes from Russell King:
"A few fixes for the recently merged development updates:
- the update to convert a code branch in the procinfo structure
forgot to update the nommu code.
- VDSO only supported for V7 CPUs and later.
- VDSO build creates files which should be ignored by git but are not.
- ensure that make arch/arm/vdso/ doesn't build if it isn't enabled"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8344/1: VDSO: honor CONFIG_VDSO in Makefile
ARM: 8343/1: VDSO: add build artifacts to .gitignore
ARM: Fix nommu booting
ARM: 8342/1: VDSO: depend on CPU_V7
|
|
Pull arch/nios2 updates from Ley Foon Tan:
- update cache management code
- rework trap handler with new define trap #.
- fix on check header warning.
* tag 'nios2-v4.1-rc1' of git://git.rocketboards.org/linux-socfpga-next:
nios2: rework cache
nios2: Add types.h header required for __u32 type
nios2: rework trap handler
nios2: remove end address checking for initda
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao.
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
eth: bf609 eth clock: add pclk clock for stmmac driver probe
blackfin: Wire up missing syscalls
arch: blackfin: kernel: kgdb: Remove unused function
dma: fix build error after update to v3.19
blackfin: io: define __raw_readx/writex with bfin_readx/writex
bf609: add resources for lcd nl8048
pm: sometimes wake up from suspend to RAM would fail
debug-mmrs: Eliminate all traces of the USB_PHY_TEST MMR
bf609: remove softswitch i2c configuration from adv7842 and adv7511 platform data
bf609: add platform data for soft switch devices on the video extenders
bf609: enable soft switch gpio driver by default
bf609: add gpio soft switch platform data for mcp23017 i2c devices
bf609: use new SND_BF6XX_PCM to choose audio pcm driver
bug[220] kgdb: change the smp cross core function entry
arch: blackfin: kernel: setup.c: Cleaning up missing null-terminate in conjunction with strncpy
blackfin: defconfigs: cleanup unused CONFIG_MTD_CHAR, add MTD_SPI_NOR for BF537-STAMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture updates from James Hogan:
"Just the one change for v4.1-rc1. A minor cleanup of copy_thread()"
* tag 'metag-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: copy_thread(): rename 'arg' argument to 'kthread_arg'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- perf fixes/improvements
- misc cleanups
* tag 'arc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: perf: don't add code for impossible case
ARC: perf: Rename DT binding to not confuse with power mgmt
ARC: perf: add user space attribution in callchains
ARC: perf: Add kernel callchain support
ARC: perf: support cache hit/miss ratio
ARC: perf: Add some comments/debug stuff
ARC: perf: make @arc_pmu static global
ARC: mem init spring cleaning - No functional changes
ARC: Fix RTT boot printing
ARC: fold __builtin_constant_p() into test_bit()
ARC: rename unhandled exception handler
ARC: cosmetic: Remove unused ECR bitfield masks
ARC: Fix WRITE_BCR
ARC: [nsimosci] Update defconfig
arc: copy_thread(): rename 'arg' argument to 'kthread_arg'
|
|
Commit cae2a173fe94 ("x86: clean up/fix 'copy_in_user()' tail zeroing")
fixed the failure case tail zeroing of one special case of the x86-64
generic user-copy routine, namely when used for the user-to-user case
("copy_in_user()").
But in the process it broke an even more unusual case: using the user
copy routine for kernel-to-kernel copying.
Now, normally kernel-kernel copies are obviously done using memcpy(),
but we have a couple of special cases when we use the user-copy
functions. One is when we pass a kernel buffer to a regular user-buffer
routine, using set_fs(KERNEL_DS). That's a "normal" case, and continued
to work fine, because it never takes any faults (with the possible
exception of a silent and successful vmalloc fault).
But Jan Beulich pointed out another, very unusual, special case: when we
use the user-copy routines not because it's a path that expects a user
pointer, but for a couple of ftrace/kgdb cases that want to do a kernel
copy, but do so using "unsafe" buffers, and use the user-copy routine to
gracefully handle faults. IOW, for probe_kernel_write().
And that broke for the case of a faulting kernel destination, because we
saw the kernel destination and wanted to try to clear the tail of the
buffer. Which doesn't work, since that's what faults.
This only triggers for things like kgdb and ftrace users (eg trying
setting a breakpoint on read-only memory), but it's definitely a bug.
The fix is to not compare against the kernel address start (TASK_SIZE),
but instead use the same limits "access_ok()" uses.
Reported-and-tested-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org # 4.0
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch e68410ebf626 ("crypto: x86/sha512_ssse3 - move SHA-384/512
SSSE3 implementation to base layer") changed the prototypes of the
core asm SHA-512 implementations so that they are compatible with
the prototype used by the base layer.
However, in one instance, the register that was used for passing the
input buffer was reused as a scratch register later on in the code,
and since the input buffer param changed places with the digest param
-which needs to be written back before the function returns- this
resulted in the scratch register to be dereferenced in a memory write
operation, causing a GPF.
Fix this by changing the scratch register to use the same register as
the input buffer param again.
Fixes: e68410ebf626 ("crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer")
Reported-By: Bobby Powers <bobbypowers@gmail.com>
Tested-By: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
- flush dcache before flush instruction cache
- remork update_mmu_cache and flush_dcache_page
- add shmparam.h
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
Reported by the header checker (CONFIG_HEADERS_CHECK=y):
CHECK usr/include/asm/ (31 files)
./usr/include/asm/ptrace.h:77: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
|
The related syscalls are below which may cause samples/kdbus building
break in next-20150401 tree, the related information and error:
CALL scripts/checksyscalls.sh
<stdin>:1223:2: warning: #warning syscall kcmp not implemented [-Wcpp]
<stdin>:1226:2: warning: #warning syscall finit_module not implemented [-Wcpp]
<stdin>:1229:2: warning: #warning syscall sched_setattr not implemented [-Wcpp]
<stdin>:1232:2: warning: #warning syscall sched_getattr not implemented [-Wcpp]
<stdin>:1235:2: warning: #warning syscall renameat2 not implemented [-Wcpp]
<stdin>:1238:2: warning: #warning syscall seccomp not implemented [-Wcpp]
<stdin>:1241:2: warning: #warning syscall getrandom not implemented [-Wcpp]
<stdin>:1244:2: warning: #warning syscall memfd_create not implemented [-Wcpp]
<stdin>:1247:2: warning: #warning syscall bpf not implemented [-Wcpp]
<stdin>:1250:2: warning: #warning syscall execveat not implemented [-Wcpp]
[...]
HOSTCC samples/kdbus/kdbus-workers
samples/kdbus/kdbus-workers.c: In function ‘prime_new’:
samples/kdbus/kdbus-workers.c:930:18: error: ‘__NR_memfd_create’ undeclared (first use in this function)
p->fd = syscall(__NR_memfd_create, "prime-area", MFD_CLOEXEC);
^
samples/kdbus/kdbus-workers.c:930:18: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
|
|
|
|
Remove the function kgdb_post_primary_code() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Rework of the prandom device with introduction of a new SHA-512 based
NIST SP 800-90 conform deterministic random bit generator.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
After the file ptes have been removed the bit combination used to
encode non-linear mappings can be reused for the swap ptes. This
frees up a precious pte software bit. Reflect the change in the
swap encoding in the comments and do some cleanup while we are
at it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The dirty & young bit from the pmd is not copied correctly to the
pseudo pte in __pmd_to_pte. In fact it is not copied at all, the
bits get lost. As the old style huge page currently does not need
the dirty & young information this has no effect, but may be needed
in the future.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The new ebpf code uses e.g. the laal instruction which is part of the
interlocked-access facility 1 which again was introduced with z196.
So we must make sure the ebpf code generator depends on MARCH_Z196_FEATURES.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Replacing a 2K page table with a 4K page table while a VMA is active
for the affected memory region is fundamentally broken. Rip out the
page table reallocation code and replace it with a simple system
control 'vm.allocate_pgste'. If the system control is set the page
tables for all processes are allocated as full 4K pages, even for
processes that do not need it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Introduce KEXEC_CONTROL_MEMORY_GFP to allow the architecture code
to override the gfp flags of the allocation for the kexec control
page. The loop in kimage_alloc_normal_control_pages allocates pages
with GFP_KERNEL until a page is found that happens to have an
address smaller than the KEXEC_CONTROL_MEMORY_LIMIT. On systems
with a large memory size but a small KEXEC_CONTROL_MEMORY_LIMIT
the loop will keep allocating memory until the oom killer steps in.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Steven Miao <realmz6@gmail.com>
|
