| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull another libata patch from Tejun Heo:
"One more patch from Adam added.
It makes libata skip probing for NCQ prio unless the feature is
explicitly requested by the user. This is necessary because some
controllers lock up after the optional feature is probed"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: avoid probing NCQ Prio Support if not explicitly requested
|
|
Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.
This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.
tj: Update formatting, switch to spin_[un]lock_irq() and update
locking a bit, use REVALIDATE instead of RESET, and return -EIO
instead of -EINVAL on config failure.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
|
|
SCT Write Same support had been introduced with
commit 7b2030942859 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42a5 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b2030942859 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
There's a typo in ata_gen_passthru_sense(), where the first byte
would be overwritten incorrectly later on.
Reported-by: Charles Machalow <csm10495@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Fixes: 11093cb1ef56 ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We previously had a check to see if the device has support for
prioritized ncq commands and a check to see if a device flag
is set, through a sysfs variable, in order to send a prioritized
command.
This patch only allows the sysfs variable to be set if the device
supports prioritized commands enabling one check in ata_build_rw_tf
in order to determine whether or not to send a prioritized command.
This patch depends on ata: ATA Command Priority Disabled By Default
tj: Minor subject and formatting updates.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Restrict support SCT Write Same to devices which also support ZAC where
support is required.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use non DMA write log when ATA_DFLAG_PIO is set.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
Correct handling of devices with sector_size other that 512 bytes.
In the case of a 4Kn device sector_size it is possible to describe a much
larger DSM Trim than the current fixed default of 512 bytes.
This patch assumes the minimum descriptor is sector_size and fills out
the descriptor accordingly.
The ACS-2 specification is quite clear that the DSM command payload is
sized as number of 512 byte transfers so a 4Kn device will operate
correctly without this patch.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
SATA drives may support write same via SCT. This is useful
for setting the drive contents to a specific pattern (0's).
Translate a SCSI WRITE SAME 16 command to be either a DSM TRIM
command or an SCT Write Same command.
Based on the UNMAP flag:
- When set translate to DSM TRIM
- When not set translate to SCT Write Same
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
Safely overwriting the attached page to ATA format from the SCSI formatted
variant.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
scsi_done() was called repeatedly and apparently because of that,
the kernel would call trace when we touch the Control mode page:
Call Trace:
[<ffffffff812ea0d2>] dump_stack+0x63/0x81
[<ffffffff81079cfb>] __warn+0xcb/0xf0
[<ffffffff81079e2d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa00f51b0>] ata_eh_finish+0xe0/0xf0 [libata]
[<ffffffffa00fb830>] sata_pmp_error_handler+0x640/0xa50 [libata]
[<ffffffffa00470ed>] ahci_error_handler+0x1d/0x70 [libahci]
[<ffffffffa00f55f0>] ata_scsi_port_error_handler+0x430/0x770 [libata]
[<ffffffffa00eff8d>] ? ata_scsi_cmd_error_handler+0xdd/0x160 [libata]
[<ffffffffa00f59d7>] ata_scsi_error+0xa7/0xf0 [libata]
[<ffffffffa00913ba>] scsi_error_handler+0xaa/0x560 [scsi_mod]
[<ffffffffa0091310>] ? scsi_eh_get_sense+0x180/0x180 [scsi_mod]
[<ffffffff81098eb8>] kthread+0xd8/0xf0
[<ffffffff815d913f>] ret_from_fork+0x1f/0x40
[<ffffffff81098de0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 8b7501047e928a17 ]---
Removed the unnecessary code and let ata_scsi_translate() do the job.
Also, since ata_mselect_control() has no ATA command to send to the
device, ata_scsi_mode_select_xlat() should return 1 for it, so that
ata_scsi_translate() will finish early to avoid ata_qc_issue().
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ata_mselect_*() would initialize a char array for storing a copy of
the current mode page. However, char could be signed char. In that
case, bytes larger than 127 would be converted to negative number.
For example, 0xff from def_control_mpage[] would become -1. This
prevented ata_mselect_control() from working at all, since when it
did the read-only bits check, there would always be a mismatch.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
|
|
`changeable` is the "version" of mode page requested by the user.
It will be less confusing/misleading if we do not check it
"together" with the setting bits of the drive.
Not to mention that we currently have ata_mselect_*() implemented
in a way that each of them will serve exclusively a particular bit
on each page. The old style will hence make the condition look even
more unnecessarily arcane if the ata_msense_*() is reflecting more
than one bit.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The reset_all variable name is misleading as this bit is also applicable to
open, close, and finish actions. So rename that variable to "all" and remove
the unnecessary mask operation that's already done earlier.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split from the previous patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The subcommand for NCQ NON-DATA must be specified in the feature
(low byte), not the high-order count byte. Also make sure to properly
cast the all bit to a u16 before shiting it by 8 to avoid undefined
behavior.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split the original patch into two, updated changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Include reporting options when translating REPORT ZONES commmand to
ATA NCQ, and make sure we only look at the actually specified bits
in the CDB for the options.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: update patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use accessor functions instead of the raw value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently libata statically allows only 1-block (512-byte) payload
for each TRIM command. Each payload can carry 64 TRIM ranges since
each range requires 8 bytes.
It is silly to keep doing the calculation (512 / 8) in different
places. Hence, define the new ATA_MAX_TRIM_RNUM for the result.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Currently if a WRITE SAME (16) command is issued to the SATL with
"number of blocks" that is larger than the "Maximum write same length"
(which is the maximum number of blocks per TRIM command allowed in
libata, currently 65535 * 512 / 8 blocks), the SATL will accept the
command and translate it to a TRIM command with the upper limit.
However, according to SBC (as of sbc4r11.pdf), the "device server"
should terminate the command with "Invalid field in CDB" in that case.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
To make it consistent with the recently added ata_mselect_control().
We probably shouldn't have the word "mode" in its name anyway, since
that's not the case for other ata_msense_*() / ata_mselect_*() either.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The bit should always be set to 1 when the requested version of
page is "changeable" because we've made it so in ata_mselect_control().
Also, it should always be set to 1 if ATA_DFLAG_D_SENSE is set (when
the requested version of page is "current" or "default").
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The comment suggests we should be having an SPC-3 version descriptor
but the 0260h is the code for "SPC-2 (no version claimed)". Correct
it to 0300h so that it has the "SPC-3 (no version claimed)" descriptor.
Note that we are claiming SPC-3 version compatibility in the VERSION
field of the standard INQUIRY data. Therefore, I assume the typo was
on the code but not on the comment.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Avoid performance bottleneck when being SCSI pass-through'd to
virtual machines with other OSes (e.g. Windows) via virtio-scsi
and scsi-block in qemu.
Ref.: https://github.com/YanVugenfirer/kvm-guest-drivers-windows/issues/63
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Commit 856c46639309 ("libata: support device-managed ZAC devices")
had the line that "bumps" the VERSION field in standard INQUIRY data
removed. Add it back and claim SPC-5 version compatibility, which
matches with the current version descriptor "SPC-5 (no version claimed)"
that is used for ZAC devices.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
It's Command Descriptor Block. Also capitalized it.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
It does not make sense and is confusing to respond with "Invalid
field in CDB" while we have no support at all implemented for
FORMAT UNIT. It is decent to let it go to the default, which
will respond with "Invalid command operation code" instead.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata ZAC support from Tejun Heo:
"This contains Zone ATA Command support for Shingled Magnetic Recording
devices.
In addition to sending the new commands down to the device, as ZAC
commands depend on getting a lot of responses from the device, piping
up responses is beefed up too. However, it doesn't involve changes to
libata core mechanism or its interaction with upper layers, so I'm not
expecting too many fallouts.
Kudos to Hannes for driving SMR support"
* 'for-4.7-zac' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (28 commits)
libata: support host-aware and host-managed ZAC devices
libata: support device-managed ZAC devices
libata: NCQ encapsulation for ZAC MANAGEMENT OUT
libata: Implement ZBC OUT translation
libata: implement ZBC IN translation
libata: fixup ZAC device disabling
libata-scsi: Generate sense code for disabled devices
libata-trace: decode subcommands
libata: Check log page directory before accessing pages
libata: Add command definitions for NCQ Encapsulation for READ LOG DMA EXT
libata: Separate out ata_dev_config_ncq_send_recv()
libata/libsas: Define ATA_CMD_NCQ_NON_DATA
libsas: enable FPDMA SEND/RECEIVE
libata: do not attempt to retrieve sense code twice
libata-scsi: Set information sense field for invalid parameter
libata-scsi: set bit pointer for sense code information
libata-scsi: Set field pointer in sense code
scsi: add scsi_set_sense_field_pointer()
libata: Implement control mode page to select sense format
libata-scsi: generate correct ATA pass-through sense
...
|
|
Byte 69 bits 0:1 in the IDENTIFY DEVICE data indicate a
host-aware ZAC device.
Host-managed ZAC devices have their own individual signature,
and to not set the bits in the IDENTIFY DEVICE data.
And whenever we detect a ZAC-compatible device we should
be displaying the zoned block characteristics VPD page.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Device-managed ZAC devices just set the zoned capabilities field
in INQUIRY byte 69 (cf ACS-4). This corresponds to the 'zoned'
field in the block device characteristics VPD page.
As this is only defined in SPC-5/SBC-4 we also need to update
the supported SCSI version descriptor.
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add NCQ encapsulation for ZAC MANAGEMENT OUT and evaluate
NCQ Non-Data log pages to figure out if NCQ encapsulation
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ZAC drives implement a 'ZAC Management Out' command template,
which maps onto the ZBC OUT command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ZAC drives implement a 'ZAC Management In' command template,
which maps onto the ZBC IN command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If a device is disabled after error recovery it doesn't make
any sense to generate an ATA sense, but we should rather
return a generic sense code indicating the device is gone.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Replace custom approach by %*ph specifier to dump small buffers in hex format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch fix spelling typos found in Documentation/Docbook/libata.xml.
It is because the file was generated from comments in source,
I had to fix comments in libata-core.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Whenever the sense key is set to 'invalid parameter' we should
be filling out the sense-key specific information field in the
sense buffer.
tj: Added description of @fp for ata_mselect_*().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
When generating a sense code of 'Invalid field in CDB' we
should be setting the bit pointer where appropriate.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If the sense code is 'Invalid field in CDB' we should be
setting the field pointer to the offending byte.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Implement MODE SELECT for the control mode page to allow the OS
to switch to descriptor sense.
tj: Dropped s/sb/cmd->sense_buffer/ in ata_gen_ata_sense(). Added
@dev description to ata_msense_ctl_mode().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Generate ATA pass-through sense for both fixed and descriptor
format sense.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use ata_scsi_set_sense() throughout to ensure the sense code
format is consistent.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If NCQ autosense or the sense data reporting feature is enabled
the LBA of the offending command should be stored in the sense
data 'information' field.
tj: s/(u64)-1/U64_MAX/
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Use scsi_set_sense_information() instead of hand-crafted function.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Return U64_MAX if ata_tf_read_block() could not decode the LBA
address, and do not set the information sense descriptor in
ata_gen_ata_sense() in these cases.
tj: s/(u64)-1/U64_MAX/
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
