| Age | Commit message (Collapse) | Author |
|---|
|
When the kernel is compiled with:
CONFIG_HIGH_RES_TIMERS=no
CONFIG_HZ_PERIODIC=yes
CONFIG_DEBUG_ATOMIC_SLEEP=yes
The following WARN appears:
WARNING: CPU: 1 PID: 0 at linux/kernel/mutex.c:856 mutex_trylock+0x70/0x1fc()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.12.0-xilinx-dirty #93
[<c0014a78>] (unwind_backtrace+0x0/0x11c) from [<c0011b6c>] (show_stack+0x10/0x14)
[<c0011b6c>] (show_stack+0x10/0x14) from [<c039120c>] (dump_stack+0x7c/0xc0)
[<c039120c>] (dump_stack+0x7c/0xc0) from [<c001fda4>] (warn_slowpath_common+0x60/0x84)
[<c001fda4>] (warn_slowpath_common+0x60/0x84) from [<c001fe48>] (warn_slowpath_fmt+0x2c/0x3c)
[<c001fe48>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0392658>] (mutex_trylock+0x70/0x1fc)
[<c0392658>] (mutex_trylock+0x70/0x1fc) from [<c02dfc08>] (clk_prepare_lock+0xc/0xe4)
[<c02dfc08>] (clk_prepare_lock+0xc/0xe4) from [<c02e099c>] (clk_get_rate+0xc/0x44)
[<c02e099c>] (clk_get_rate+0xc/0x44) from [<c02d0394>] (ttc_set_mode+0x34/0x78)
[<c02d0394>] (ttc_set_mode+0x34/0x78) from [<c005f794>] (clockevents_set_mode+0x28/0x5c)
[<c005f794>] (clockevents_set_mode+0x28/0x5c) from [<c00607fc>] (tick_broadcast_on_off+0x190/0x1c0)
[<c00607fc>] (tick_broadcast_on_off+0x190/0x1c0) from [<c005f168>] (clockevents_notify+0x58/0x1ac)
[<c005f168>] (clockevents_notify+0x58/0x1ac) from [<c02b99dc>] (cpuidle_setup_broadcast_timer+0x20/0x24)
[<c02b99dc>] (cpuidle_setup_broadcast_timer+0x20/0x24) from [<c006cd04>] (generic_smp_call_function_single_interrupt+0)
[<c006cd04>] (generic_smp_call_function_single_interrupt+0xe0/0x130) from [<c00138c8>] (handle_IPI+0x88/0x118)
[<c00138c8>] (handle_IPI+0x88/0x118) from [<c0008504>] (gic_handle_irq+0x58/0x60)
[<c0008504>] (gic_handle_irq+0x58/0x60) from [<c0012644>] (__irq_svc+0x44/0x78)
Exception stack(0xef099fa0 to 0xef099fe8)
9fa0: 00000001 ef092100 00000000 ef092100 ef098000 00000015 c0399f2c c0579d74
9fc0: 0000406a 413fc090 00000000 00000000 00000000 ef099fe8 c00666ec c000f46c
9fe0: 20000113 ffffffff
[<c0012644>] (__irq_svc+0x44/0x78) from [<c000f46c>] (arch_cpu_idle+0x34/0x3c)
[<c000f46c>] (arch_cpu_idle+0x34/0x3c) from [<c0053980>] (cpu_startup_entry+0xa8/0x10c)
[<c0053980>] (cpu_startup_entry+0xa8/0x10c) from [<000085a4>] (0x85a4)
We are in an interrupt context (IPI) and we are calling clk_get_rate in the
set_mode function which in turn ends up by getting a mutex... Even if that
does not hang, it is a potential kernel deadlock.
It is not allowed to call clk_get_rate() from interrupt context. To
avoid such calls the timer input frequency is stored in the driver's
data struct which makes it accessible to the driver in any context.
[dlezcano] completed the changelog with the WARN trace and added a more
detailed description. Tested on zync zc702.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In commit 620f5e1cbf (dts: Rename DW APB timer compatible strings), both
"snps,dw-apb-timer-sp" and "snps,dw-apb-timer-osc" were deprecated in place
of "snps,dw-apb-timer". But the driver also needs to be udpated in order to
support this new binding "snps,dw-apb-timer".
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The read_sched_clock should return the ~value because the clock is a
countdown implementation. read_sched_clock() should be the same as
__apbt_read_clocksource().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The sun4i timer can still be ticking when we enable the interrupt.
If another timer is actually used (A7 architected timer, for example),
odds are that the interrupt will eventually fire with the event_handler
pointer being NULL.
The obvious fix it to stop the timer before registering the interrupt.
Observed and tested on sun7i (cubietruck).
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
When booting a recent kernel on ARM with OF_DYNAMIC enabled, the kernel
warns about the following:
[ 0.000000] ERROR: Bad of_node_put() on /timer@50004600
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12.0-rc5-next-20131017-00077-gedfd827-dirty #406
[ 0.000000] [<c0015b68>] (unwind_backtrace+0x0/0xf4) from [<c00117e4>] (show_stack+0x10/0x14)
[ 0.000000] [<c00117e4>] (show_stack+0x10/0x14) from [<c055f734>] (dump_stack+0x9c/0xc8)
[ 0.000000] [<c055f734>] (dump_stack+0x9c/0xc8) from [<c03b47d4>] (of_node_release+0x90/0x9c)
[ 0.000000] [<c03b47d4>] (of_node_release+0x90/0x9c) from [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4)
[ 0.000000] [<c03b5084>] (of_find_matching_node_and_match+0x78/0xb4) from [<c07887c8>] (clocksource_of_init+0x60/0x70)
[ 0.000000] [<c07887c8>] (clocksource_of_init+0x60/0x70) from [<c076e99c>] (start_kernel+0x1f4/0x33c)
[ 0.000000] [<c076e99c>] (start_kernel+0x1f4/0x33c) from [<80008074>] (0x80008074)
This is caused by clocksource_of_init() dropping a reference on the
device node that it never took. The reference taken by the loop is
implicitly dropped on subsequent iterations. See the implementation of
and the comment on top of the of_find_matching_node_and_match()
function for reference (no pun intended).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
This commit registers the sched_clock _after_ the counter reset
(instead of before). This removes the timestamp 'jump' in kernel
log messages.
Before this change:
[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798691800ns
[ 0.000000] Initializing Coherency fabric
[ 0.000000] Aurora cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12, Cache size: 1024 kB
[ 163.507447] Calibrating delay loop... 1325.05 BogoMIPS (lpj=662528)
[ 163.521419] pid_max: default: 32768 minimum: 301
[ 163.526185] Mount-cache hash table entries: 512
[ 163.531095] CPU: Testing write buffer coherency: ok
After this change:
[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798691800ns
[ 0.000000] Initializing Coherency fabric
[ 0.000000] Aurora cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12, Cache size: 1024 kB
[ 0.016849] Calibrating delay loop... 1325.05 BogoMIPS (lpj=662528)
[ 0.030820] pid_max: default: 32768 minimum: 301
[ 0.035588] Mount-cache hash table entries: 512
[ 0.040500] CPU: Testing write buffer coherency: ok
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
|
The time-efm32 driver uses the clocksource MMIO functions.
Thus it needs to select CLKSRC_MMIO in Kconfig.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
Pavel Machek reports that this config is exposed on x86 where the
ARM architected timers aren't even present. Make it depend on the
ARM architected timers being selected so that non-ARM builds
aren't asked about it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Fix the probe error path to release the clock resource when the
sh_tmu_register() call fails.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Fix the probe error path to release the clock resource when the
sh_mtu2_register() call fails.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
IRQF_DISABLED is a no-op nowadays, so we can safely remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
We need to wait for at least 2 clock cycles whenever we reprogram our
clockevent timer. Report that the minimum number of ticks we can handle
is 3 ticks, and remove 3 ticks to the interval programmed to reflect
this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Allwinner SoCs timer use the clocksource MMIO functions. We thus
need to select them in Kconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
An efm32 features 4 16-bit timers with a 10-bit prescaler. This driver
provides clocksource and clock event device using one timer instance
each.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Commit:
65cd4f6 ("arch_timer: Move to generic sched_clock framework")
added code to register the arch_sys_counter in arch_timer_register(),
but it is already registered in arch_counter_register().
This results in the timer being added to the clocksource list twice,
therefore causing an infinite loop in the list.
Remove the duplicate registration and register the scheduler
clock after the original registration instead.
This fixes a hang during boot on Tegra114 (Cortex-A15).
[ While I've only tested this on Tegra114, I suspect the same hang
during boot happens for all processors that use this clock source. ]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1381843911-31962-1-git-send-email-treding@nvidia.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.linaro.org/people/jstultz/linux into timers/core
Pull more timekeeping items for v3.13 from John Stultz:
* Small cleanup in the clocksource code.
* Fix for rtc-pl031 to let it work with alarmtimers.
* Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Register with the generic sched_clock framework now that it
supports 64 bits. This fixes two problems with the current
sched_clock support for machines using the architected timers.
First off, we don't subtract the start value from subsequent
sched_clock calls so we can potentially start off with
sched_clock returning gigantic numbers. Second, there is no
support for suspend/resume handling so problems such as discussed
in 6a4dae5 (ARM: 7565/1: sched: stop sched_clock() during
suspend, 2012-10-23) can happen without this patch. Finally, it
allows us to move the sched_clock setup into drivers clocksource
out of the arch ports.
Cc: Christopher Covington <cov@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Remove the deprecated IRQF_DISABLED flag.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Check function return values to avoid false positive driver init.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
clk_prepare_enable/disable_unprepare
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
clockevents/3.13
Adds support to configure the rate and enable the event stream for architected
timer. The event streams can be used to impose a timeout on a wfe, to safeguard
against any programming error in case an expected event is not generated or
even to implement wfe-based timeouts for userspace locking implementations.
This feature can be disabled(enabled by default).
Since the timer control register is reset to zero on warm boot, CPU PM notifier
is added to save and restore the value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.linaro.org/people/dlezcano/linux into timers/core
Pull (mostly) ARM clocksource driver updates from Daniel Lezcano:
" - Soren Brinkmann added FEAT_PERCPU to a clock device when it is local
per cpu. This feature prevents the clock framework to choose a per cpu
timer as a broadcast timer. This problem arised when the ARM global
timer is used when switching to the broadcast timer which is the case
now on Xillinx with its cpuidle driver.
- Stephen Boyd extended the generic sched_clock code to support 64bit
counters and removes the setup_sched_clock deprecation, as that causes
lots of warnings since there's still users in the arch/arm tree. He
added also the CLOCK_SOURCE_SUSPEND_NONSTOP flag on the architected
timer as they continue counting during suspend.
- Uwe Kleine-König added some missing __init sections and consolidated the
code by moving the of_node_put call from the drivers to the function
clocksource_of_init. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The ARM architected timers keep counting during suspend so we can
mark this clocksource with the CLOCK_SOURCE_SUSPEND_NONSTOP flag.
This flag will indicate that this clocksource can be used for
calculating suspend time and injecting sleep time into the
timekeeping core. This should be more accurate than using an
external RTC or architecture specific persistent clock.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
These are all only called by dw_apb_timer_init which is an __init
function, too
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Instead of letting each driver call of_node_put do it centrally in the
loop that also calls the CLOCKSOURCE_OF_DECLARE callbacks. This is less
prone to error and also moves getting and putting the references into the
same function.
Consequently all respective of_node_put calls in drivers are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
|
|
The arm_global_timer is a per cpu device. Set the appropriate flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
|
|
fordlezcano/3.13/sched-clock64-conversion
Update to tip/timers/core and resolve minor conflict.
Conflicts:
drivers/clocksource/samsung_pwm_timer.c
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Few control settings done in architected timer as part of initialisation
can be lost when CPU enters deeper power states. They need to be
restored when the CPU is (warm)reset again.
This patch adds CPU PM notifiers to save the counter control register
when entering low power modes and restore it when CPU exits low power.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
|
|
The ARM architected timer can generate events (used for waking up
CPUs executing the wfe instruction) at a frequency represented as a
power-of-2 divisor of the clock rate.
An event stream might be used:
- To implement wfe-based timeouts for userspace locking implementations.
- To impose a timeout on a wfe for safeguarding against any programming
error in case an expected event is not generated.
This patch computes the event stream frequency aiming for a period
of 100us between events. It uses ARM/ARM64 specific backends to configure
and enable the event stream.
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[sudeep: moving ARM/ARM64 changes into separate patches
and adding Kconfig option]
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
|
|
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
f7db706 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This commit:
573145f08c2b92c45498468afbbba909f6ce6135
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
replaced a call to the driver's timer initialization by a call to
clocksource_of_init(). However, it failed to select CONFIG_CLKSRC_OF.
Fix this by selecting CONFIG_CLKSRC_OF for Armada370/XP machines.
Without this change the kernel is stuck at: 'Calibrating delay loop...'.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
|
|
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
|
|
When booting with device tree static clkdev aliases should not be used.
This patch modifies the samsung_pwm_timer driver to use DT-based clock
lookup when booting with device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
|
|
The Armada XP timer has two mandatory clock inputs: nbclk and refclk,
as specified by the device-tree binding.
This commit fixes the clock selection. Instead of hard-coding the clock
rate for the 25 MHz reference fixed-clock, obtain the clock by its name.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
If the clock fails to be obtained and the timer fails to be properly
registered, the kernel will freeze real soon. Instead, let's BUG()
where the actual problem is located.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada XP SoC clocksource driver cannot work without the 25 MHz
fixed timer. Therefore it's appropriate to introduce a new compatible
string and use it to set the 25 MHz fixed timer.
The 'marvell,timer-25MHz' property will be marked as deprecated.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
|
This is almost cosmetic: we achieve a bit of consistency with
other clocksource drivers by using the CLOCKSOURCE_OF_DECLARE
macro for the boilerplate code.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
|
This commit creates two functions to access the TIMER_CTRL register:
one for global one for the per-cpu. This makes the code much more
readable. In addition, since the TIMER_CTRL register is also used for
watchdog, this is preparation work for future thread-safe improvements.
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This is a purely cosmetic commit: we replace hardcoded values that
representing bits by BIT(), which is slightly more readable.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
|
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add the dynamic irq affinity feature to the timer clock device.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
|
