aboutsummaryrefslogtreecommitdiff
path: root/drivers/gpio/gpio-rcar.c
AgeCommit message (Collapse)Author
2021-02-15gpio: rcar: Add R-Car V3U (R8A779A0) supportGeert Uytterhoeven
Add support for the GPIO controller block in the R-Car V3U (R8A779A0) SoC, which is very similar to the block found on other R-Car Gen3 SoCs. However, this block has a new General Input Enable Register (INEN), whose reset state is to have all inputs disabled. Enable input for all available pins in probe and resume, to support the use of the General Input Register (INDT) for reading pin state at all times. This preserves backwards compatibility with other R-Car Gen3 SoCs, as recommended by the Hardware Manual. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15gpio: rcar: Optimize GPIO pin state read on R-Car Gen3Geert Uytterhoeven
Currently, the R-Car GPIO driver treats R-Car Gen2 and R-Car Gen3 GPIO controllers the same. However, there exist small differences, like the behavior of the General Input Register (INDT): - On R-Car Gen1, R-Car Gen2, and RZ/G1, INDT only reflects the state of an input pin if the GPIO is configured for input, - On R-Car Gen3 and RZ/G2, INDT always reflects the state of the input pins. Hence to accommodate all variants, the driver does not use the INDT register to read the status of a GPIO line when configured for output, at the expense of doing 2 or 3 register reads instead of 1. Given register accesses are slow, change the .get() and .get_multiple() callbacks to always use INDT to read pin state on SoCs where this is supported. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-02-15gpio: rcar: Remove redundant compatible valuesLad Prabhakar
The mandatory compatible values 'renesas,rcar-gen{1,2,3}-gpio' have been already added to all the respective R-Car Gen{1,2,3} SoC DTSI files, remove the redundant device specific values from the driver. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-10-30gpio: rcar: Implement gpio_chip.get_multiple()Geert Uytterhoeven
Add support for getting the state of multiple pins using a minimum of register reads. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-10-30gpio: rcar: Rework hardware features handlingGeert Uytterhoeven
Reuse gpio_rcar_info inside gpio_rcar_priv instead of duplicating the individual members, so gpio_rcar_parse_dt() can copy them in one go. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-10-30gpio: rcar: Align register offsetsGeert Uytterhoeven
Improve readability by aligning the offsets in the register definitions. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-10-30gpio: rcar: Cache gpiochip_get_data() return valueGeert Uytterhoeven
Since commit 43c54ecade400cf6 ("gpio: move the subdriver data pointer into gpio_device") changed gpiochip_get_data() to an out-of-line function, it is now worthwhile to avoid multiple calls in a row by caching its return value in a local variable. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-07-30gpio: rcar: Use irqchip templateLinus Walleij
This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit call to gpiochip_irqchip_add(). The irqchip is instead added while adding the gpiochip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Biju Das <biju.das@bp.renesas.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200722113141.243163-1-linus.walleij@linaro.org
2020-05-25gpio: rcar: Fix runtime PM imbalance on errorDinghao Liu
pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20200522080839.32612-1-dinghao.liu@zju.edu.cn Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-02-20gpio: rcar: Fix typo in commentAshish Chavan
"Positive" is spelled incorrectly as "Postive" in comment fix this. Signed-off-by: Ashish Chavan <ashish.gschavan@gmail.com> Link: https://lore.kernel.org/r/20200209095600.16394-1-ashish.gschavan@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-12gpio: rcar: Use proper irq_chip nameGeert Uytterhoeven
The irq_chip .name field should contain the device's class name, not the instance's name. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-11-07gpio: Use new GPIO_LINE_DIRECTIONMatti Vaittinen
It's hard for occasional GPIO code reader/writer to know if values 0/1 equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT to help them out. NOTE - for gpio-amd-fch and gpio-bd9571mwv: This commit also changes the return value for direction get to equal 1 for direction INPUT. Prior this commit these drivers might have returned some other positive value but 1 for INPUT. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Acked-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-06-27gpio: rcar: Pedantic formattingEnrico Weigelt, metux IT consult
A tab sneaked in, where it shouldn't be. Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-05drivers: gpio: rcar: use devm_platform_ioremap_resource()Enrico Weigelt, metux IT consult
Use the new helper that wraps the calls to platform_get_resource() and devm_ioremap_resource() together. Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-21gpio: rcar: select General Output Register to set output statesVladimir Zapolskiy
R-Car GPIO controller provides two interfaces to set GPIO line output signal state, and for a particular GPIO line the selected interface is determined by OUTDTSEL bit value. At the moment the driver supports only one of two interfaces, namely OUTDT General Output Register is used to control the output signal. While this selection is the default one on reset, it is not explicitly configured on probe, thus it might be possible that kernel and userspace consumers of a GPIO won't be able to set the wanted GPIO output signal. Below is a simple test case to reproduce the described problem and verify this fix in the kernel on H3 ULCB by setting non-default OUTDTSEL configuration from a bootloader: u-boot > mw.l 0xe6055440 0x3000 1 ... userspace > echo default-on > /sys/devices/platform/leds/leds/led5/trigger userspace > echo default-on > /sys/devices/platform/leds/leds/led6/trigger Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-05gpio: rcar: reference device instead of platform deviceVladimir Zapolskiy
The change simplifies dereferences to the mediated struct device, also it allows to limit the scope of the platform device usage to probe and remove functions only. Non-functional change. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-15gpio: rcar: convert to SPDX identifiersKuninori Morimoto
This patch updates license to use SPDX-License-Identifier instead of verbose license text. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-08-29gpio: rcar: Add GPIO hole supportBiju Das
GPIO hole is present in RZ/G1C SoC. Valid GPIO pins on bank3 are in the range GP3_0 to GP3_16 and GP3_27 to GP3_29. The GPIO pins between GP3_17 to GP3_26 are unused. Add support for handling unused GPIO's. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-13gpio: rcar: Implement .get_direction() callbackGeert Uytterhoeven
Allow gpiolib to read back the current I/O direction configuration by implementing the .get_direction() callback. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-02gpio: rcar: Include the right headerLinus Walleij
This is a GPIO driver, include only <linux/gpio/driver.h>. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-18Merge tag 'v4.16-rc5' into develLinus Walleij
Linux 4.16-rc5 merged into the GPIO devel branch to resolve a nasty conflict between fixes and devel in the RCAR driver. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-05gpio: rcar: Use wakeup_path i.s.o. explicit clock handlingGeert Uytterhoeven
Since commit ab82fa7da4dce5c7 ("gpio: rcar: Prevent module clock disable when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO block's module clock (if exists) is manually kept running during system suspend, to make sure the device stays active. However, this explicit clock handling is merely a workaround for a failure to properly communicate wakeup information to the device core. Instead, set the device's power.wakeup_path field, to indicate this device is part of the wakeup path. Depending on the PM Domain's active_wakeup configuration, the genpd core code will keep the device enabled (and the clock running) during system suspend when needed. This allows for the removal of all explicit clock handling code from the driver. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22gpio: gpio-rcar: Support S2RAMHien Dang
This patch adds an implementation that saves and restores the state of GPIO configuration on suspend and resume. Signed-off-by: Hien Dang <hien.dang.eb@renesas.com> Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> [Modify structure of the bank info to simplify a saving registers] [Remove DEV_PM_OPS macro] Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-09Merge branch 'gpio-irqchip-rework' of /home/linus/linux-gpio into develLinus Walleij
2017-11-08gpio: Move irqdomain into struct gpio_irq_chipThierry Reding
In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-31gpio-rcar: use devm_ioremap_resource()Sergei Shtylyov
Using devm_ioremap_resource() has several advantages over devm_ioremap(): - it checks the passed resource's validity; - it calls devm_request_mem_region() to check for the resource overlap; - it prints an error message in case of error. We can call devm_ioremap_resource() instead of devm_ioremap_nocache() as ioremap() and ioremap_nocache() are implemented identically on ARM. Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5). Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-08gpio: rcar: Use of_device_get_match_data() helperGeert Uytterhoeven
Use the of_device_get_match_data() helper instead of open coding. Note that the gpio-rcar driver is used with DT only, so there's always a valid match. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-22pinctrl/gpio: Unify namespace for cross-callsLinus Walleij
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice namespacing in the other cross-calls like pinctrl_gpio_foo(). Just rename them and all references so we have one namespace with all cross-calls under pinctrl_gpio_*(). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14gpio: rcar: add gen[123] fallback compatibility stringsSimon Horman
Add fallback compatibility string for R-Car Gen 1, 2 and 3. In the case of Renesas R-Car hardware we know that there are generations of SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship between IP blocks might be. For example, I believe that r8a7790 is older than r8a7791 but that doesn't imply that the latter is a descendant of the former or vice versa. We can, however, by examining the documentation and behaviour of the hardware at run-time observe that the current driver implementation appears to be compatible with the IP blocks on SoCs within a given generation. For the above reasons and convenience when enabling new SoCs a per-generation fallback compatibility string scheme being adopted for drivers for Renesas SoCs. Also deprecate renesas,gpio-rcar as its name is more generic than its implementation. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-29gpio: rcar: Add R8A7743 (RZ/G1M) supportBiju Das
Renesas RZ/G1M (R8A7743) SoC GPIO blocks are identical to the R-Car Gen2 family. Add support for its GPIO controllers. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Chris Paterson <chris.paterson2@renesas.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-28gpio: rcar: Fine-grained Runtime PM supportGeert Uytterhoeven
Currently gpio modules are runtime-resumed at probe time. This means the gpio module will be active all the time (except during system suspend, if not configured as a wake-up source). While an R-Car Gen2 gpio module retains pins configured for output at the requested level while put in standby mode, gpio register cannot be accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be called from all contexts where gpio register access is needed. Hence move the Runtime PM handling from probe/remove time to gpio request/free time, which is probably the best we can do. On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6 for SD-Card CD & WP, gpio7 for keys and regulators). Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> [Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/] Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-28gpio: rcar: set IRQ chip parent_deviceNiklas Söderlund
This enables Runtime PM handling for interrupts. By setting the parent_device in struct irq_chip genirq will call the pm_runtime_get/put APIs when an IRQ is requested/freed. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-08gpio: rcar: Add r8a7796 (R-Car M3-W) supportSimon Horman
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect. Based on work for the r8a7795 (R-Car H3) by Ulrich Hecht. Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-22gpio: rcar: add R8A7792 supportSergei Shtylyov
Renesas R8A7792 SoC is a member of the R-Car gen2 family, add support for its GPIO controllers. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-17Merge tag 'gpio-v4.7-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for kernel cycle v4.7: Core infrastructural changes: - Support for natively single-ended GPIO driver stages. This means that if the hardware has registers to configure open drain or open source configuration, we use that rather than (as we did before) try to emulate it by switching the line to an input to get high impedance. This is also documented throughly in Documentation/gpio/driver.txt for those of you who did not understand one word of what I just wrote. - Start to do away with the unnecessarily complex and unitelligible ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from the time when the GPIO subsystem was unmaintained. Archs can now just select GPIOLIB and be done with it, cleanups to arches will trickle in for the next kernel. Some minor archs ACKed the changes immediately so these are included in this pull request. - Advancing the use of the data pointer inside the GPIO device for storing driver data by switching the PowerPC, Super-H Unicore and a few other subarches or subsystem drivers in ALSA SoC, Input, serial, SSB, staging etc to use it. - The initialization now reads the input/output state of the GPIO lines, so that each GPIO descriptor knows - if this callback is implemented - whether the line is input or output. This also reflects nicely in userspace "lsgpio". - It is now possible to name GPIO producer names, line names, from the device tree. (Platform data has been supported for a while). I bet we will get a similar mechanism for ACPI one of those days. This makes is possible to get sensible producer names for e.g. GPIO rails in "lsgpio" in userspace. New drivers: - New driver for the Loongson1. - The XLP driver now supports Broadcom Vulcan ARM64. - The IT87 driver now supports IT8620 and IT8628. - The PCA953X driver now supports Galileo Gen2. Driver improvements: - MCP23S08 was switched to use the gpiolib irqchip helpers and now also suppors level-triggered interrupts. - 74x164 and RCAR now supports the .set_multiple() callback - AMDPT was converted to use generic GPIO. - TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994 support the new single ended callback for open drain and in some cases open source. - Implement the .get_direction() callback for a few more drivers like PL061, Xgene. Cleanups: - Paul Gortmaker combed through the drivers and de-modularized those who are not really modules. - Move the GPIO poweroff DT bindings to the power subdir where they belong. - Rename gpio-generic.c to gpio-mmio.c, which is much more to the point. That's what it is handling, nothing more, nothing less" * tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits) MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB gpio: zevio: make it explicitly non-modular gpio: timberdale: make it explicitly non-modular gpio: stmpe: make it explicitly non-modular gpio: sodaville: make it explicitly non-modular pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms gpio: dt-bindings: add wd,mbl-gpio bindings gpio: of: make it possible to name GPIO lines gpio: make gpiod_to_irq() return negative for NO_IRQ gpio: xgene: implement .get_direction() gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver gpio: tegra: Implement gpio_get_direction callback gpio: set up initial state from .get_direction() gpio: rename gpio-generic.c into gpio-mmio.c gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case gpio: dwapb: add gpio-signaled acpi event support gpio: dwapb: convert device node to fwnode gpio: dwapb: remove name from dwapb_port_property gpio/qoriq: select IRQ_DOMAIN ...
2016-04-12Revert "gpio: rcar: Fine-grained Runtime PM support"Linus Walleij
This reverts commit 65194cb174b873448b208eb6e04ecb72237af76e.
2016-04-12Revert "gpio: rcar: Add Runtime PM handling for interrupts"Linus Walleij
This reverts commit b26a719bdba9aa926ceaadecc66e07623d2b8a53.
2016-03-30gpio: rcar: Implement gpiochip.set_multiple()Geert Uytterhoeven
This allows to set multiple outputs using a single register write. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-25gpio: rcar: Add Runtime PM handling for interruptsGeert Uytterhoeven
The R-Car GPIO driver handles Runtime PM for requested GPIOs only. When using a GPIO purely as an interrupt source, no Runtime PM handling is done, and the GPIO module's clock may not be enabled. To fix this: - Add .irq_request_resources() and .irq_release_resources() callbacks to handle Runtime PM when an interrupt is requested, - Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM when e.g. disabling/enabling an interrupt, or configuring the interrupt type. Fixes: d5c3d84657db57bd "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS" Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05gpio: rcar: use gpiochip data pointerLinus Walleij
This makes the driver use the data pointer added to the gpio_chip to store a pointer to the state container instead of relying on container_of(). Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-11gpio: rcar: Improve clock error handling and reportingGeert Uytterhoeven
If the Renesas R-Car GPIO driver cannot find a functional clock, it prints a warning, .e.g. gpio_rcar ffc40000.gpio: unable to get clock and continues, as the clock is optional, depending on the SoC type. This warning may confuse users. To fix this, add a flag to indicate that the clock is mandatory or optional: - If the clock is mandatory (on R-Car Gen2 and Gen3), a missing clock is now treated as a fatal error, - If the clock is optional (on R-Car Gen1), the warning is no longer printed. Suggested-by: Magnus Damm <magnus.damm@gmail.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-11gpio: rcar: Remove obsolete platform data supportGeert Uytterhoeven
Since commit 4baadb9e05c68962 ("ARM: shmobile: r8a7778: remove obsolete setup code"), Renesas R-Car SoCs are only supported in generic DT-only ARM multi-platform builds. The driver doesn't need to use platform data anymore, hence remove platform data configuration. Make gpio_rcar_priv.has_both_edge_trigger a boolean for consistency with gpio_rcar_info.has_both_edge_trigger. Move gpio_rcar_priv.irq_parent down while we're at it, to prevent gaps on 64-bit. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19gpio: change member .dev to .parentLinus Walleij
The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-27gpio: rcar: Add r8a7795 (R-Car H3) supportUlrich Hecht
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect. Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-16gpio: rcar: Fine-grained Runtime PM supportGeert Uytterhoeven
Currently gpio modules are runtime-resumed at probe time. This means the gpio module will be active all the time (except during system suspend, if not configured as a wake-up source). While an R-Car Gen2 gpio module retains pins configured for output at the requested level while put in standby mode, gpio registercannot be accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be called from all contexts where gpio register access is needed. Hence move the Runtime PM handling from probe/remove time to gpio request/free time, which is probably the best we can do. On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6 for SD-Card CD & WP, gpio7 for keys and regulators). Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-01gpio: rcar: Check for irq_set_irq_wake() failuresGeert Uytterhoeven
If an interrupt controller doesn't support wake-up configuration, irq_set_irq_wake() returns an error code. Then any subsequent call trying to deconfigure wake-up will cause an imbalance, and a warning will be printed: WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x9c/0xf8() Unbalanced IRQ 26 wake disable To fix this, refrain from any further parent interrupt controller (de)configuration if irq_set_irq_wake() failed. Alternative fixes would be: - calling "gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE)" from the platform code, - setting "gic_chip.flags = IRQCHIP_SKIP_SET_WAKE" in the GIC driver code, but these were withheld as the GIC hardware doesn't really support wake-up interrupts. Fixes: ab82fa7da4dce5c7 ("gpio: rcar: Prevent module clock disable when wake-up is enabled") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Prevent module clock disable when wake-up is enabledGeert Uytterhoeven
When the GPIO module is needed for wake-up, it's module clock must not be disabled. Hence implement irq_chip.irq_set_wake(), which increments/decrements the clock's enable_count when needed, and forwards the wake-up state to the upstream interrupt controller. This fixes wake-up from s2ram using gpio-keys when using a PM Domain to manage the module clock. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Add more register documentationGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Use local variable gpio_chip in gpio_rcar_probe()Geert Uytterhoeven
The existing variable gpio_chip already points to the gpiochip instance, hence use it everywhere. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-15gpio: rcar: Switch to use gpiolib irqchip helpersGeert Uytterhoeven
Switch the R-Car Gen2 GPIO driver to use the gpiolib irqchip helpers. While doing this also make sure that gpiochip_irqchip_add() is called after the gpiochip itself is registered, as required. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-25 14:02:55 +0000