aboutsummaryrefslogtreecommitdiff
path: root/drivers/gpio/gpio-stmpe.c
AgeCommit message (Collapse)Author
2021-05-21gpio: stmpe: fully use convert probe to device-managedAlexandru Ardelean
The IRQ is registered via devm_request_threaded_irq(), making the driver only partially device-managed. This changeset converts the entire driver to using only devres APIs. This change also removes platform_set_drvdata() since the information is never retrieved to be used in the driver. Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> [Bart: tweaked the commit message] Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-10-28gpio: stmpe: Fix forgotten refactoringLinus Walleij
We actually handle the gpio_irq_chip set-up properly now despite what the comment says. Also assign this pointer along with the rest of the gpio_irq_chip setup code. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20201019134429.65563-1-linus.walleij@linaro.org
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-04gpio: stmpe: Move chip registrationLinus Walleij
Make sure to register the GPIO chip after requesting the interrupt and setting up the IRQ members of the irqchip. Fixes: 9745079609df ("gpio: stmpe: Use irqchip template") Reported-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Link: https://lore.kernel.org/r/20200728072706.348725-1-linus.walleij@linaro.org
2020-07-20gpio: stmpe: Use irqchip templateLinus Walleij
This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit calls to gpiochip_irqchip_add_nested() and gpiochip_set_nested_irqchip(). The irqchip is instead added while adding the gpiochip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Link: https://lore.kernel.org/r/20200716100638.112451-1-linus.walleij@linaro.org
2019-11-07gpio: Use new GPIO_LINE_DIRECTIONMatti Vaittinen
It's hard for occasional GPIO code reader/writer to know if values 0/1 equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT to help them out. NOTE - for gpio-amd-fch and gpio-bd9571mwv: This commit also changes the return value for direction get to equal 1 for direction INPUT. Prior this commit these drivers might have returned some other positive value but 1 for INPUT. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Acked-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-11gpio: Initialize the irqchip valid_mask with a callbackLinus Walleij
After changing the valid_mask for the struct gpio_chip to detect the need and presence of a valid mask with the presence of a .init_valid_mask() callback to fill it in, we augment the gpio_irq_chip to use the same logic. Switch all driver using the gpio_irq_chio valid_mask over to this new method. This makes sure the valid_mask for the gpio_irq_chip gets filled in when we add the gpio_chip, which makes it a little easier to switch over drivers using the old way of setting up gpio_irq_chip over to the new method of passing the gpio_irq_chip along with the gpio_chip. (See drivers/gpio/TODO for details.) Cc: Joel Stanley <joel@jms.id.au> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 464Thomas Gleixner
Based on 1 normalized pattern(s): license terms gnu general public license version 2 extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 11 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Enrico Weigelt <info@metux.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081202.373849232@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-02gpio: stmpe: Include the right headerLinus Walleij
This is a GPIO driver, include only <linux/gpio/driver.h>. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-24gpio: Remove VLA from stmpe driverLaura Abbott
The new challenge is to remove VLAs from the kernel (see https://lkml.org/lkml/2018/3/7/621) The number of GPIOs on the supported chips is fairly small so stack allocate to a known upper bound and spit out a warning if any new chips have more gpios. Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Phil Reid <preid@electromag.com.au> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-17gpio: stmpe: Delete an unnecessary variable initialisation in stmpe_gpio_probe()Markus Elfring
The local variable "irq" will eventually be set to an appropriate value a bit later. Thus omit the explicit initialisation at the beginning. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-17gpio: stmpe: Move an assignment in stmpe_gpio_probe()Markus Elfring
Move the assignment for the local variable "irq" so that its setting will only be performed directly before it is checked by this function. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-17gpio: stmpe: Improve a size determination in stmpe_gpio_probe()Markus Elfring
Replace the specification of a data structure by a pointer dereference as the parameter for the operator "sizeof" to make the corresponding size determination a bit safer according to the Linux coding style convention. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-17gpio: stmpe: Use seq_putc() in stmpe_dbg_show()Markus Elfring
A single character (line break) should be put into a sequence. Thus use the corresponding function "seq_putc". This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-17gpio: stmpe: i2c transfer are forbiden in atomic contextPatrice Chotard
Move the workaround from stmpe_gpio_irq_unmask() which is executed in atomic context to stmpe_gpio_irq_sync_unlock() which is not. It fixes the following issue: [ 1.500000] BUG: scheduling while atomic: swapper/1/0x00000002 [ 1.500000] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc2-00020-gbd4301f-dirty #28 [ 1.520000] Hardware name: STM32 (Device Tree Support) [ 1.520000] [<0000bfc9>] (unwind_backtrace) from [<0000b347>] (show_stack+0xb/0xc) [ 1.530000] [<0000b347>] (show_stack) from [<0001fc49>] (__schedule_bug+0x39/0x58) [ 1.530000] [<0001fc49>] (__schedule_bug) from [<00168211>] (__schedule+0x23/0x2b2) [ 1.550000] [<00168211>] (__schedule) from [<001684f7>] (schedule+0x57/0x64) [ 1.550000] [<001684f7>] (schedule) from [<0016a513>] (schedule_timeout+0x137/0x164) [ 1.550000] [<0016a513>] (schedule_timeout) from [<00168b91>] (wait_for_common+0x8d/0xfc) [ 1.570000] [<00168b91>] (wait_for_common) from [<00139753>] (stm32f4_i2c_xfer+0xe9/0xfe) [ 1.580000] [<00139753>] (stm32f4_i2c_xfer) from [<00138545>] (__i2c_transfer+0x111/0x148) [ 1.590000] [<00138545>] (__i2c_transfer) from [<001385cf>] (i2c_transfer+0x53/0x70) [ 1.590000] [<001385cf>] (i2c_transfer) from [<001388a5>] (i2c_smbus_xfer+0x12f/0x36e) [ 1.600000] [<001388a5>] (i2c_smbus_xfer) from [<00138b49>] (i2c_smbus_read_byte_data+0x1f/0x2a) [ 1.610000] [<00138b49>] (i2c_smbus_read_byte_data) from [<00124fdd>] (__stmpe_reg_read+0xd/0x24) [ 1.620000] [<00124fdd>] (__stmpe_reg_read) from [<001252b3>] (stmpe_reg_read+0x19/0x24) [ 1.630000] [<001252b3>] (stmpe_reg_read) from [<0002c4d1>] (unmask_irq+0x17/0x22) [ 1.640000] [<0002c4d1>] (unmask_irq) from [<0002c57f>] (irq_startup+0x6f/0x78) [ 1.650000] [<0002c57f>] (irq_startup) from [<0002b7a1>] (__setup_irq+0x319/0x47c) [ 1.650000] [<0002b7a1>] (__setup_irq) from [<0002bad3>] (request_threaded_irq+0x6b/0xe8) [ 1.660000] [<0002bad3>] (request_threaded_irq) from [<0002d0b9>] (devm_request_threaded_irq+0x3b/0x6a) [ 1.670000] [<0002d0b9>] (devm_request_threaded_irq) from [<001446e7>] (mmc_gpiod_request_cd_irq+0x49/0x8a) [ 1.680000] [<001446e7>] (mmc_gpiod_request_cd_irq) from [<0013d45d>] (mmc_start_host+0x49/0x60) [ 1.690000] [<0013d45d>] (mmc_start_host) from [<0013e40b>] (mmc_add_host+0x3b/0x54) [ 1.700000] [<0013e40b>] (mmc_add_host) from [<00148119>] (mmci_probe+0x4d1/0x60c) [ 1.710000] [<00148119>] (mmci_probe) from [<000f903b>] (amba_probe+0x7b/0xbe) [ 1.720000] [<000f903b>] (amba_probe) from [<001170e5>] (driver_probe_device+0x169/0x1f8) [ 1.730000] [<001170e5>] (driver_probe_device) from [<001171b7>] (__driver_attach+0x43/0x5c) [ 1.740000] [<001171b7>] (__driver_attach) from [<0011618d>] (bus_for_each_dev+0x3d/0x46) [ 1.740000] [<0011618d>] (bus_for_each_dev) from [<001165cd>] (bus_add_driver+0xcd/0x124) [ 1.740000] [<001165cd>] (bus_add_driver) from [<00117713>] (driver_register+0x4d/0x7a) [ 1.760000] [<00117713>] (driver_register) from [<001fc765>] (do_one_initcall+0xbd/0xe8) [ 1.770000] [<001fc765>] (do_one_initcall) from [<001fc88b>] (kernel_init_freeable+0xfb/0x134) [ 1.780000] [<001fc88b>] (kernel_init_freeable) from [<00167ee3>] (kernel_init+0x7/0x9c) [ 1.790000] [<00167ee3>] (kernel_init) from [<00009b65>] (ret_from_fork+0x11/0x2c) Cc: stable@vger.kernel.org Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-02gpio: gpio-stmpe: make various char arrays static const, shrinks object sizeColin Ian King
Don't populate the read-only arrays edge_det_values, rise_values and fall_values on the stack but instead make them static and constify them. Makes the object code smaller by over 240 bytes: Before: text data bss dec hex filename 9525 2520 192 12237 2fcd drivers/gpio/gpio-stmpe.o After: text data bss dec hex filename 9025 2776 192 11993 2ed9 drivers/gpio/gpio-stmpe.o (gcc version 7.2.0 x86_64) Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-08gpio: Move irq_valid_mask into struct gpio_irq_chipThierry Reding
In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-08gpio: Move irqdomain into struct gpio_irq_chipThierry Reding
In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-19gpio: mark expected switch fall-throughsGustavo A. R. Silva
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-13Merge tag 'gpio-v4.10-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Luinus Walleij: "Bulk GPIO changes for the v4.10 kernel cycle: Core changes: - Simplify threaded interrupt handling: instead of passing numbed parameters to gpiochip_irqchip_add_chained() we create a new call: gpiochip_irqchip_add_nested() so the two types are clearly semantically different. Also make sure that all nested chips call gpiochip_set_nested_irqchip() which is necessary for IRQ resend to work properly if it happens. - Return error on seek operations for the chardev. - Clamp values set as part of gpio[d]_direction_output() so that anything != 0 will be send down to the driver as "1" not the value passed in. - ACPI can now support naming of GPIO lines, hogs and holes in the GPIO lists. New drivers: - The SX150x driver was deemed unfit for the GPIO subsystem and was moved over to a combined GPIO+pinctrl driver in the pinctrl subsystem. New features: - Various cleanups to various drivers" * tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits) gpio: merrifield: Implement gpio_get_direction callback gpio: merrifield: Add support for hardware debouncer gpio: chardev: Return error for seek operations gpio: arizona: Tidy up probe error path gpio: arizona: Remove pointless set of platform drvdata gpio: pl061: delete platform data handling gpio: pl061: move platform data into driver gpio: pl061: rename variable from chip to pl061 gpio: pl061: rename state container struct gpio: pl061: use local state for parent IRQ storage gpio: set explicit nesting on drivers gpio: simplify adding threaded interrupts gpio: vf610: use builtin_platform_driver gpio: axp209: use correct register for GPIO input status gpio: stmpe: fix interrupt handling bug gpio: em: depnd on ARCH_SHMOBILE gpio: zx: depend on ARCH_ZX gpio: x86: update config dependencies for x86 specific hardware gpio: mb86s7x: use builtin_platform_driver gpio: etraxfs: use builtin_platform_driver ...
2016-12-07Merge branch 'thread-irq-simpler' into develLinus Walleij
2016-11-25gpio: simplify adding threaded interruptsLinus Walleij
This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when using threaded interrupts: add a new call gpiochip_irqchip_add_nested() to indicate that we're dealing with a nested rather than a chained irqchip, then create a separate gpiochip_set_nested_irqchip() to mirror the gpiochip_set_chained_irqchip() call to connect the parent and child interrupts. In the nested case gpiochip_set_nested_irqchip() does nothing more than call irq_set_parent() on each valid child interrupt, which has little semantic effect in the kernel, but this is probably still formally correct. Update all drivers using nested interrupts to use gpiochip_irqchip_add_nested() so we can now see clearly which these users are. The DLN2 driver can drop its specific hack with .irq_not_threaded as we now recognize whether a chip is threaded or not from its use of gpiochip_irqchip_add_nested() signature rather than from inspecting .can_sleep. We rename the .irq_parent to .irq_chained_parent since this parent IRQ is only really kept around for the chained interrupt handlers. Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: Daniel Baluta <daniel.baluta@intel.com> Cc: Bin Gao <bin.gao@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com> Cc: Semen Protsenko <semen.protsenko@globallogic.com> Cc: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Phil Reid <preid@electromag.com.au> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-24gpio: stmpe: fix interrupt handling bugLinus Walleij
commit 43db289d00c6 ("gpio: stmpe: Rework registers access") reworked the STMPE register access so as to use [STMPE_IDX_*_LSB + i] to access the 8bit register for a certain bank, assuming the CSB and MSB will follow after the enumerator. For this to work the index needs to go from (size-1) to 0 not 0 to (size-1). However for the GPIO IRQ handler, the status registers we read register MSB + 3 bytes ahead for the 24 bit GPIOs and index registers from MSB upwards and run an index i over the registers UNLESS we are STMPE1600. This is not working when we get to clearing the interrupt EDGE status register STMPE_IDX_GPEDR_[LCM]SB: it is indexed like all other registers [STMPE_IDX_*_LSB + i] but in this loop we index from 0 to get the right bank index for the calculations, and we need to just add i to the MSB. Before this, interrupts on the STMPE2401 were broken, this patch fixes it so it works again. Cc: stable@vger.kernel.org Cc: Patrice Chotard <patrice.chotard@st.com> Fixes: 43db289d00c6 ("gpio: stmpe: Rework registers access") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-20gpio: stmpe: || vs && typoDan Carpenter
&& was obviously intended here. Fixes: 6936e1f88d23 ('gpio: stmpe: Write int status register only when needed') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-30gpio: stmpe: use BIT() macroLinus Walleij
Avoid custom (1 << bits) shifting by consequently using the BIT() macro from <linux/bitops.h>. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-30gpio: stmpe: forbid unused lines to be mapped as IRQsLinus Walleij
Exploit the new mechanism for masking off disallowed IRQs added by Mika Westerberg to properly manage the STMPE "norequest mask" to disallow also mapping said lines as IRQs. Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-13gpio: constify gpio_chip structuresJulia Lawall
These structures are only used to copy into other structures, so declare them as const. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct gpio_chip i@p = { ... }; @ok@ identifier r.i; expression e; position p; @@ e = i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct gpio_chip e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct gpio_chip i = { ... }; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-08-10gpio: stmpe: Add STMPE1600 supportPatrice Chotard
The particularities of this variant are: - GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared to other variants. - There is no Edge detection, Rising Edge and Falling Edge registers. - IRQ flags are cleared when read, no need to write in Status register. Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10gpio: stmpe: Rework registers accessPatrice Chotard
This update allows to use registers map as following : regs[reg_index + offset] instead of regs[reg_index] + offset This makes code clearer and will facilitate the addition of STMPE1600 on which LSB and MSB registers are respectively located at addr and addr + 1. Despite for all others STMPE variant, LSB and MSB registers are respectively located in reverse order at addr + 1 and addr. For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH) register addresses (STMPE1801/STMPE24xx). For variant which have 2 registers's bank, we use LSB and CSB indexes only. In this case the CSB index contains the MSB regs address (STMPE 1601). Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10gpio: stmpe: Write int status register only when neededPatrice Chotard
On STMPE801/1801 datasheets, it's mentionned writing in interrupt status register has no effect, bits are cleared when reading. Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10gpio: stmpe: Fix edge and rising/falling edge detectionPatrice Chotard
By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets, it appears that edge detection and rising/falling edge detection is not supported by all STMPE variant: GPIO GPIO Edge detection rising/falling edge detection 610 | X | X | 801 | | | 811 | X | X | 1600 | | | 1601 | X | X | 1801 | | X | 2401 | X | X | 2403 | X | X | Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly take these cases into account. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-07gpio: remove redundant owner assignments of driversMasahiro Yamada
A platform_driver need not set an owner since it will be populated by platform_driver_register(). Likewise for mcb_driver (gpio-menz127.c). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-07gpio: stmpe: implement .get_direction()Linus Walleij
This implements the .get_direction() callback for the STMPE expander GPIO. Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-11gpio: stmpe: make it explicitly non-modularPaul Gortmaker
The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_STMPE drivers/gpio/Kconfig: bool "STMPE GPIOs" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. We explicitly disallow a driver unbind, since that doesn't have a sensible use case anyway, and it allows us to drop the ".remove" code for non-modular drivers. Curiously, this driver was using subsys_initcall since day one, so we don't have the "normal" module_init replacement in this change like we've done in other similar driver updates. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Rabin Vincent <rabin.vincent@stericsson.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05gpio: stmpe: use gpiochip data pointerLinus Walleij
This makes the driver use the data pointer added to the gpio_chip to store a pointer to the state container instead of relying on container_of(). Cc: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19gpio: change member .dev to .parentLinus Walleij
The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-20gpio: stmpe: enforce device tree only modeLinus Walleij
Require that device tree be used with STMPE (all platforms use this) and enforce OF_GPIO, then delete the platform data. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-02gpio: stmpe: add verbose debug codeLinus Walleij
To troubleshoot the STMPE GPIO driver, some more detailed debug information giving the exact info on how each pin is used will be helpful. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-10-02gpio: stmpe: fix up interrupt enable logicLinus Walleij
The STMPE driver assumes that the passed in IRQ type is for rising or falling IRQs, not both, even though the hardware actually supports this perfectly well. Likewise the check for level IRQs is done against just high or low level types, not for the case where it is combined with other IRQs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-26gpio: handle also nested irqchips in the chained handler set-upLinus Walleij
To unify how we connect cascaded IRQ chips to parent IRQs, if NULL us passed as handler to the gpiochip_set_chained_irqchip() function, assume the chips is nested rather than chained, and we still get the parent set up correctly by way of this function call. Alter the drivers for tc3589x and stmpe to use this to set up their chained handlers as a demonstration of the usage. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-07-22gpio: remove all usage of gpio_remove retval in driver/gpioabdoulaye berthe
Signed-off-by: abdoulaye berthe <berthe.ab@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-06-19gpio: stmpe: switch to use gpiolib irqchip helpersLinus Walleij
This switches the STMPE driver to use the gpiolib irqchip helpers. Tested-by: Silvio Fricke <silvio.fricke@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-23mfd: stmpe: root out static GPIO and IRQ assignmentsLinus Walleij
The only platform using the STMPE expander now boots from device tree using all-dynamic GPIO and IRQ number assignments, so remove the mechanism to pass this from the device tree entirely. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-04gpio/pinctrl: make gpio_chip members typed booleanLinus Walleij
This switches the two members of struct gpio_chip that were defined as unsigned foo:1 to bool, because that is indeed what they are. Switch all users in the gpio and pinctrl subsystems to assign these values with true/false instead of 0/1. The users outside these subsystems will survive since true/false is 1/0, atleast we set some kind of more strict typing example. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-16gpio: stmpe: drop references to "virtual" IRQ, fix bugLinus Walleij
Rename the argument "virq" to just "irq", this IRQ isn't any more "virtual" than any other Linux IRQ number, we use "hwirq" for the actual hw-numbers, "virq" is just bogus. When doing this I see that the hwirq argument is used for mapping rather than the Linux IRQ in the map function. This doesn't look right. Use the Linux IRQ instead. I cannot test this patch so I don't know if the mapping change is correct, however since absolutely every other driver does it the other way around this doesn't look sound at all. Please help out with review. Cc: Vipul Kumar Samar <vipulkumar.samar@st.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Gabriel Fernandez <gabriel.fernandez@st.com> Cc: Jean-Nicolas Graux <jean-nicolas.graux@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-05-30gpio: stmpe: Staticize non-exported symbolsAxel Lin
Both stmpe_gpio_irq_map() and stmpe_gpio_irq_unmap() are not referenced outside of this file, make them static. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-05-30gpio: stmpe: remove unnecessary platform_set_drvdata()Jingoo Han
The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-03-27gpio: stmpe: pass DT node to irqdomainGabriel Fernandez
The irq domain was implemented but the device tree node was not transmitted to irq_domain_add_simple(). Cc: stable@vger.kernel.org Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-12-11Merge tag 'driver-core-3.8-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg Kroah-Hartman: "Here's the large driver core updates for 3.8-rc1. The biggest thing here is the various __dev* marking removals. This is going to be a pain for the merge with different subsystem trees, I know, but all of the patches included here have been ACKed by their various subsystem maintainers, as they wanted them to go through here. If this is too much of a pain, I can pull all of them out of this tree and just send you one with the other fixes/updates and then, after 3.8-rc1 is out, do the rest of the removals to ensure we catch them all, it's up to you. The merges should all be trivial, and Stephen has been doing them all in linux-next for a few weeks now quite easily. Other than the __dev* marking removals, there's nothing major here, some firmware loading updates and other minor things in the driver core. All of these have (much to Stephen's annoyance), been in linux-next for a while. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>" Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio update. * tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits) modpost.c: Stop checking __dev* section mismatches init.h: Remove __dev* sections from the kernel acpi: remove use of __devinit PCI: Remove __dev* markings PCI: Always build setup-bus when PCI is enabled PCI: Move pci_uevent into pci-driver.c PCI: Remove CONFIG_HOTPLUG ifdefs unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs sh/PCI: Remove CONFIG_HOTPLUG ifdefs powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs mips/PCI: Remove CONFIG_HOTPLUG ifdefs microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs dma: remove use of __devinit dma: remove use of __devexit_p firewire: remove use of __devinitdata firewire: remove use of __devinit leds: remove use of __devexit leds: remove use of __devinit leds: remove use of __devexit_p mmc: remove use of __devexit ...
2012-12-10gpio: Provide the STMPE GPIO driver with its own IRQ DomainLee Jones
The STMPE GPIO driver can be used as an IRQ controller by some related devices. Here we provide it with its very own IRQ Domain so that IRQs can be issued dynamically. This will stand the driver in good stead when it is enabled for Device Tree, as this it a prerequisite. Cc: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-14 18:33:04 +0000