| Age | Commit message (Collapse) | Author |
|---|
|
With "modprobe sbp2 long_ieee1394_id=y", the format of
/sys/bus/scsi/devices/*:*:*:*/ieee1394_id is changed from e.g.
0001041010004beb:0:0 to 0001041010004beb:00042c:0000.
The longer format fully conforms to object identifier sizes as per
SAM(-2...4) and reflects what the SAM target port identifier is meant to
contain: A Discovery ID allegedly specified by ISO/IEC 13213:1994 ---
however there is no such thing; the authors of SAM probably meant
Directory ID). Especially target nodes with multiple dynamically added
targets may use Directory IDs to persistently identify target ports.
The new format is independent of implementation details of nodemgr.
Thus the same ieee1394_id attribute format can be implemented in the new
firewire stack.
The ieee1394_id is typically used to create persistently named links in
/dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
drivers/ieee1394/sbp2.c: In function 'sbp2util_access_timeout':
drivers/ieee1394/sbp2.c:399: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/ieee1394/sbp2.c:399: error: (Each undeclared identifier is reported only once
drivers/ieee1394/sbp2.c:399: error: for each function it appears in.)
drivers/ieee1394/sbp2.c:399: warning: implicit declaration of function 'signal_pending'
drivers/ieee1394/sbp2.c:399: warning: implicit declaration of function 'schedule_timeout'
drivers/ieee1394/sbp2.c: In function 'sbp2_prep_command_orb_sg':
drivers/ieee1394/sbp2.c:1438: warning: implicit declaration of function 'page_address'
drivers/ieee1394/sbp2.c:1438: warning: passing argument 2 of 'dma_map_single' makes pointer from integer without a cast
drivers/ieee1394/sbp2.c: In function 'sbp2_handle_status_write':
drivers/ieee1394/sbp2.c:1842: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
Possibly due to changes in -mm, but this file should explicitly include the
headers for the stuff it uses.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (brought into alphabetic order)
|
|
When the command ORB pool is created, the ORB list won't be accessed
concurrently. Therefore we don't have to take the spinlock there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Unlike the name suggests, "cmd->scatter_gather_element" holds only the
s/g table, not the actual s/g elements. Since the table is only read
but never written by the device, DMA_BIDIRECTIONAL can be replaced by
DMA_TO_DEVICE which may be cheaper on some architectures.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
In order to use OHCI-1394 physical DMA, all s/g elements, s/g tables,
ORBs, and response buffers have to reside within the first 4 GB of the
FireWire controller's physical address space. Set the correct mask for
DMA mappings.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The old setting is copy & waste from usb-storage and doesn't apply to
sbp2. There is only 4-byte alignment required for everything, except
for S/G table elements which have to be 8-byte aligned according to the
SBP-2 spec. (They happen to be ____cacheline_aligned in our
implementation. Whether that's good is another question.)
We now simply don't tune block queue alignment at all. The default
alignment would surely never become anything else than a multiple of 4,
else tons of calls to blk_queue_dma_alignment would have to be added
everywhere in drivers/...
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
There is no emulation going on here.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
0x000000 could be a valid value to match against, but anything bigger
than 0xffffff cannot.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Since commit 98e238cd42be6c0852da519303cf0182690f8d9f in Linux 2.6.19,
"ieee1394: sbp2: don't prefer MODE SENSE 10", some FireWire DVD-ROMs and
DVD-RWs were mistaken as CD-ROM because sr_mod now sent MODE SENSE 6.
The MMC command set includes only MODE SENSE 10.
http://bugzilla.kernel.org/show_bug.cgi?id=7800
This fix lets sbp2 switch scsi_device.use_10_for_rw on for MMC LUs.
This should rather be done in the command set driver sr_mod, not in the
sbp2 transport driver, and an according patch will follow for a next
Linux release.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Need to use a PCI device, not a FireWire host device. Problem found by
Andreas Schwab, mistake pointed out by Benjamin Herrenschmidt.
http://ozlabs.org/pipermail/linuxppc-dev/2006-December/029595.html
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Andreas Schwab <schwab@suse.de>
|
|
Delete some incorrect code, left over from the initial driver submission
in March 2001.
SBP-2 targets should provide sense data via the SBP-2 status block
(autosense). We have to pass the REQUEST_SENSE command through to
targets which don't implement autosense, if there are any, and to
accomodate application clients which use this command.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Merge is finished, can bring the code in readable style again.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This patch consolidates some bookkeeping for driver registering. It
closely models what pci_register_driver() does. The main addition is
that the owner of the driver is set, so we get a proper symlink
for /sys/bus/ieee1394/driver/*/module.
Also moves setting of name and bus type into nodemgr. Because of this,
we can remove the EXPORT_SYMBOL for ieee1394_bus_type, since it's now
only used in ieee1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
API conversion without change in functionality
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Move the body of a function into its only caller.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Some people actually look at those comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
It's OK to reorder list_del() and sbp2util_free_command_dma() here.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
"struct scsi_id_instance_data" represents a logical unit.
Rename it to "struct sbp2_lu", and "scsi_id" to "lu".
Rename some other variables too.
Wrap almost all lines after at most 80 columns.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
It's 2^20 bit/s, not 0.001 bit.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Prepend sbp2*_ to anything globally defined in sbp2.c except for some
macros. Strip sbp2_ from names of struct members.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
And update and reformat remaining comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This work is not delayed.
Also bring the code format in a state which reduces my work to merge
pending sbp2 patchs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
No need to keep them in released sources.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Replace some calls to SBP2_ERR and SBP2_WARN by SBP2_INFO.
Remove logging macros SBP2_NOTICE and SBP2_WARN.
Remove direct usage of HPSB_ logging macros.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The same case is handled further below in sbp2scsi_complete_command.
Note, the second version behaves slightly different but looks
preferable. It's an extremely unlikely case by the way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This has been within #if 0 for a long time and is wrong anyway.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Remove unnecessary function prototypes.
Remove variable names from function prototypes.
Move declarations from sbp2.h to sbp2.c.
Move definitions of driver templates together near the top of sbp2.c.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The queue depth can be read from /sys/bus/scsi/devices/*/queue_depth,
so don't log it. And the hint about speed improvements is misleading,
at least under current kernels. If serialization is switched off, read
performance is typically increased by less than 10%. (I did not test
write performance recently.) On the other hand, serialize_io=0 is not
yet safe due to some implementation issues that are not trivial to fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Put the target's fetch agent into reset state before the underlying ORB
DMA is unmapped and the ->done handler is called. It is highly unlikely
but the target could access that ORB right before sbp2 sends the reset
request.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Fix up for make allyesconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
This is a follow-up to patch "ieee1394: sbp2: enable auto spin-up for
Maxtor disks". When I 'ejected' an OXUF922 based HDD from a Mac OS X
box, it was spun down by the Mac and did not spin up by itself when
attached to a Linux box right after that. The first SCSI command that
required the bridge to access the drive ended in
sda:<6>sd 18:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
Additional sense: Logical unit not ready, initializing cmd. required
Therefore the flag which instructs scsi_mod to send START STOP UNIT with
START=1 ("make medium ready") after such a condition is now enabled
unconditionally for all FireWire storage devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
In the old days, sbp2 used to coerce all MODE SENSE commands into the
10 bytes version. When all command set conversions were removed from
sbp2 several months ago, sdev->use_10_for_ms = 1 was added. Meaning,
higher SCSI layers preferred the 10 bytes version but would try the 6
bytes version if the former failed.
Recently, a problem with the 10 bytes version was discovered. An Initio
INIC-1530 firmware accepted the 10 bytes version but replied with bogus
data, showing the HDD incorrectly as write-protected. Since RBC
actually mandates MODE SENSE (6), I checked which version was sent by
Windows XP and Mac OS X 10.3 to an SBP-2 target hosted by Linux --- it
was the 6 bytes version. (Exception: OS X sent the 10 bytes version to
an MMC target. RBC and SBC got MODE SENSE (6).)
Therefore, drop the use_10_for_ms flag from sbp2. Now the upper layers
will try MODE SENSE (6) before MODE SENSE (10) on all SBP-2 devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Scsi_remove_device() may go into uninterruptible sleep if blocked.
Therefore sbp2_remove() unblocks the Scsi_Host before the device is
requested to be removed. But there could be another 1394 bus reset
after that which would block the host again. The 1394 subsystem won't
call sbp2_update() concurrently to sbp2_remove(), which is why there is
no chance for sbp2_remove() to be unblocked by sbp2_update().
The fix is to tell sbp2's bus reset handler when a device is to be shut
down so that it skips scsi_block_requests() on that host. As before,
any new commands after a reset without reconnect will be failed quickly
by sbp2scsi_queuecommand().
In the long term, means to go without scsi_block_requests() should be
found.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Remove unused includes. Add missing includes, i.e. explicitly include
all used headers. Sort includes alphabetically. Replace one call to
signal_pending(current) to avoid to include headers just for this line.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
If the target signals a transport failure via status block, complete the
request with DID_BUSY to indicate to the SCSI subsystem that the command
may succeed when retried.
Also log diagnostic information if the status block shows a transport
related problem. It may point to hardware faults.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
While sbp2_update() is doing its duties after a bus reset, another reset
could happen. Don't accept new requests until the next undisturbed
sbp2_update() or until sbp2_remove().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The scsi_host_template's eh_abort_handler and eh_device_reset_handler
are allowed to sleep. Use this to run sbp2_agent_reset in the more
reliable mode which returns _after_ its write transaction was finished.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=6948
Because sbp2 writes to the target's fetch agent's registers from within
atomic context, it cannot sleep to guaranteedly get a free transaction
label. This may repeatedly lead to "sbp2util_node_write_no_wait failed"
and consequently to SCSI command abortion after timeout. A likely cause
is that many queue_command softirqs may occur before khpsbpkt (the
ieee1394 driver's thread which cleans up after finished transactions) is
woken up to recycle tlabels.
Sbp2 now schedules a workqueue job whenever sbp2_link_orb_command fails
in sbp2util_node_write_no_wait. The job will reliably get a transaction
label because it can sleep.
We use the kernel-wide shared workqueue because it is unlikely that the
job itself actually needs to sleep. In the improbable case that it has
to sleep, it doesn't need to sleep long since the standard transaction
timeout is 100ms.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
A deactivated macro, defined as "#define foo(bar)", will result in
silent corruption if somebody forgets a semicolon after a call to foo.
Replace it by "#define foo(bar) do {} while (0)" which will reveal any
respective syntax errors.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This patch contains the scheduled removal of the force_inquiry_hack
module parameter.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The waitqueue API is used to replace a custom wait mechanism. Only one
global waitqueue (instead of per-device waitqueues or completions) is
added because there is usually just one waiter.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
- Add checks for the (very unlikely) cases that the target writes too
little or too much status data or writes unsolicited status.
- Indicate that these and similar conditions are unlikely().
- Check the 'resp' and 'sbp_status' fields for possible failure status.
- Slightly optimize access macros for the status block bitfields.
- Unify a few related log messages.
TODO: Check if 'src'==1, then withhold the respective ORB from reuse
until status for any subsequent ORB was received. This is an old bug
whose fix requires more complex command queue handling.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Sbp2's copy of the status fifo was cleared when management ORBs or new
command ORBs were prepared. The latter had potential for a race
condition if the block layer's soft IRQ and the 1394 LLD's interrupt
handler ran on different CPUs. It would also yield wrong status if a
command was completed with non-zero completion status before other
commands that had zero completion status, and no new command was
enqueued in the meantime.
Now, the status buffer is cleared right before it is written. Thus it
ends up in the following simpler and safer access pattern:
- sbp2_alloc_device: allocates and implicitly clears once,
- sbp2_handle_status_write: clears, writes, and reads,
- sbp2_query_logins, sbp2_login_device, sbp2_reconnect_device: read.
The latter three do not race with sbp2_handle_status_write because of
how the protocol works.
As a tiny optimization, the first two quadlets of the status never need
to be cleared.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Only the driver writes ORBs, the device just reads them. Therefore
PCI_DMA_BIDIRECTIONAL can be replaced by PCI_DMA_TODEVICE which may be
cheaper on some architectures.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Since sbp2 is at the moment unable to do anything with the return value
of sbp2_link_orb_command, just discard it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The sbp2 initiator has two ways to tell a target's fetch agent about new
command ORBs:
- Write the ORB's address to the ORB_POINTER register. This must not
be done while the fetch agent is active.
- Put the ORB's address into the previously submitted ORB's next_ORB
field and write to the DOORBELL register. This may be done while the
fetch agent is active or suspended. It must not be done while the
fetch agent is in reset state.
Sbp2 has a last_orb pointer which indicates in what way a new command
should be announced. That pointer is concurrently accessed at various
occasions. Furthermore, initiator and target are accessing the next_ORB
field of ORBs concurrently and asynchronously.
This patch does:
- Protect all initiator accesses to last_orb by sbp2_command_orb_lock.
- Add pci_dma_sync_single_for_device before a previously submitted
ORB's next_ORB field is overwritten.
- Insert a memory barrier between when next_ORB_lo and next_ORB_hi are
overwritten. Next_ORB_hi must not be updated before next_ORB_lo.
- Remove the rather unspecific and now superfluous qualifier "volatile"
from the next_ORB fields.
- Add comments on how last_orb is connected with what is known about
the target's fetch agent's state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
|
