| Age | Commit message (Collapse) | Author |
|---|
|
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MS5607 is temperature and pressure sensor which hardware is similar to MS5611.
Both sensors share command protocol and support both I2C and SPI serial
protocols. They only differ in compensation algorithms.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SCALE is useful whenever conversion to standard units is done
in userspace. In this case conversion is handled by driver so this bit
is unnecessary.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
|
|
'channels' is allocated via kmemdup and it is never freed in the
subsequent error paths.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fix "null" in the raw attribute and scan elements.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
|
|
Conflicts:
drivers/iio/common/hid-sensors/hid-sensor-trigger.c
include/linux/hid-sensor-hub.h
|
|
Temperature reads on bmp280 device always return 0,
due to a missing step in the compensation formula
(data->tfine is never initialized).
Initialize data->tfine value so we get correct
temperature and pressure values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for Measurement Specialities MS5611 pressure
and temperature sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use common hid sensor iio pm functions. Also the poll time read and
wait is part of power up function of hid sensor iio pm function, so
remove from the client drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The calculations for temperature and pressure compensation were already slightly
optimized in comparison to the datasheet. So, it makes sense to optimize even a
bit more, making proper use of C operators:
- variable t in bmp280_compensate_temp() can be eliminated by directly
returning the result of the relevant equation.
- make use of the += operator and eliminate an unnecessary parenthesis level in
bmp280_compensate_press().
When the initialization of the ctrl_meas register fails, the error message will
now mention the right register name.
During probe, i2c_set_clientdata() is called, although it is not necessary. Drop
it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This version of the code avoids extra memory copy operations and is
somewhat smaller in code size.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
According to the datasheet and as defined in struct bmp280_comp_press, dig_p1 is
of type u16, while dig_p2 to dig_p9 are of type s16. In
bmp280_read_compensation_press(), values read from the device were treated as
the wrong type.
In bmp280_read_press() the fractional part of the measured pressure is
calculated wrong. A better way is to use *val for the raw pressure and *val2 for
the quotient and let the core do the proper conversion using IIO_VAL_FRACTIONAL.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The proper way to divide two signed 64-bit values is to use div64_s64.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Minimal implementation, can read temperature and data using direct mode.
Datasheet available at
<http://ae-bst.resource.bosch.com/media/products/dokumente/bmp280/BST-BMP280-DS001-09.pdf>
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch fix pressure data variable name. Usually pdata name
it is used for platform data.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch removes the .owner field for drivers which use the
platform_driver_register api because this is overriden in
_platform_driver_register.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the fixes in -rc5 in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The I2C devices that make up the STMicroelectronics MEMS sensors
may be sneakily enabled by cleverly giving the device node the same
name as a string match from the platform device ID table. However
the right method is to use the compatible string.
On detection, the ST sensors use the ID string to probe and
instatiate the right sensor driver, so pass the kernel-internal ID
string in the .data field of the OF match table, and set the I2C
client name to this name when a compatible match is used.
This avoids having misc Linux-specific strings floating around in
the device tree.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
support.
This allows in kernel client drivers to access this
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Agreed with by Srinivas.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the staging fixes here as well.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.16 cycle.
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
|
|
16-bit pressure and temperature sensor
the chip can do I2C and SPI, only the I2C interface is supported
by the driver at the moment
datasheet: http://www.epcos.com/inf/57/ds/T5400.pdf
application note: http://www.epcos.com/blob/993154/download/1/t5403-applicationnote.pdf
an out-of-tree driver targetting the input subsystem is at
https://github.com/unixphere/t5400, it was rejected here:
http://comments.gmane.org/gmane.linux.kernel.input/28107
v2: (thanks Hartmut Knaack)
* fix MODE_HIGH, equals 2
* check INT_TIME mask in write_raw()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Stefan Nilsson <stefan.nilsson@unixphere.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
(i) pressure is 20-bit unsigned, not signed; the buffer description
is incorrect; for raw reads, this is just cosmetic
(ii) temperature is 12-bit signed, not 16-bit; this affects
readout of temperatures below zero as the sign bit is incorrectly
processed
reported via private mail
Cc: stable@vger.kernel.org
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Robert Deliën <robert@delien.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
I2C-controlled sensor with 10-bit pressure and temperature measurement
datasheet: http://cache.freescale.com/files/sensors/doc/data_sheet/MPL3115A2.pdf
v2:
* use devm_iio_device_register()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the pressure sensor has code to retrieve and enable two
regulators for Vdd and Vdd IO, but actually these voltage inputs
are found on all of these ST sensors, so move the regulator
handling to the core and make sure all the ST sensors call these
functions on probe() and remove() to enable/disable power.
Here also mover over to obtaining the regulator from the *parent*
device of the IIO device, as the IIO device is created on-the-fly
in this very subsystem it very unlikely evert have any regulators
attached to it whatsoever. It is much more likely that the parent
is a platform device, possibly instantiated from a device tree,
which in turn have Vdd and Vdd IO supplied assigned to it.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
It is pretty helpful to know already from dmesg that a certain
device is successfully registered, instead of having to browse
sysfs to see if it's actually there.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for the new barometer sensor: LPS25H.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added usage id processing for Pressure Sensor. This uses IIO
interfaces for triggered buffer to present data to user
mode. This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
>> >> drivers/iio/pressure/mpl3115.c:101:46: sparse: cast to restricted __be32
>> >> drivers/iio/pressure/mpl3115.c:115:46: sparse: cast to restricted __be32
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
I2C-controlled MEMS sensor with 20-bit pressure measurement (pascal) and
12-bit temperature measurement
driver only exposes basic functionality, see TODO remarks
datasheet: http://cache.freescale.com/files/sensors/doc/data_sheet/MPL3115A2.pdf
v2:
* store 20-bit value in 32-bit buffer element (instead of 24-bit)
* zero buffer to prevent kernel data leak to userspace
* fix mutex unlock in trigger handler (thanks Andi Shyti)
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer core,
so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The power to some of the sensors are controlled by regulators. In most
cases these are 'always on', but if not they will fail to work until
the regulator is enabled using the relevant APIs. This patch allows for
the Vdd_IO power supply to be specified by either platform data or
Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The power to some of the sensors are controlled by regulators. In most
cases these are 'always on', but if not they will fail to work until
the regulator is enabled using the relevant APIs. This patch allows for
the Vdd power supply to be specified by either platform data or Device
Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch fix buffer registration that allows to use generic IIO trigger.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
