aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc/host/sdhci.c
AgeCommit message (Collapse)Author
2021-07-02mmc: sdhci: Fix warning message when accessing RPMB in HS400 modeAl Cooper
When an eMMC device is being run in HS400 mode, any access to the RPMB device will cause the error message "mmc1: Invalid UHS-I mode selected". This happens as a result of tuning being disabled before RPMB access and then re-enabled after the RPMB access is complete. When tuning is re-enabled, the system has to switch from HS400 to HS200 to do the tuning and then back to HS400. As part of sequence to switch from HS400 to HS200 the system is temporarily put into HS mode. When switching to HS mode, sdhci_get_preset_value() is called and does not have support for HS mode and prints the warning message and returns the preset for SDR12. The fix is to add support for MMC and SD HS modes to sdhci_get_preset_value(). This can be reproduced on any system running eMMC in HS400 mode (not HS400ES) by using the "mmc" utility to run the following command: "mmc rpmb read-counter /dev/mmcblk0rpmb". Signed-off-by: Al Cooper <alcooperx@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-06-29mmc: sdhci: Clear unused bounce buffer at DMA mmap error pathTakashi Iwai
When DMA-mapping of the bounce buffer fails, the driver tries to fall back, but it leaves the allocated host->bounce_buffer although its size is zero. Later on, the driver checks the use of bounce buffer with host->bounce_buffer pointer, and it tries to use the buffer incorrectly, resulting in Oops. This patch clears the release the unused buffer and clears the bounce_buffer pointer for addressing the problem. Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20210611101948.18972-1-tiwai@suse.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-06-14mmc: Improve function name when aborting a tuning cmdWolfram Sang
'mmc_abort_tuning()' made me think tuning gets completely aborted. However, it sends only a STOP cmd to cancel the current tuning cmd. Tuning process may still continue after that. So, rename the function to 'mmc_send_abort_tuning()' to better reflect all this. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-03-30mmc: sdhci: replace mmc->parent with mmc_dev() for consistencyJisheng Zhang
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being used in the entire c-file". Convert all the mmc->parent usage in all sdhci host driver to mmc_dev() for consistency. Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-03-30mmc: sdhci: Use "mmc" directly rather than "host->mmc"Jisheng Zhang
Clean up the code to use the "mmc" directly instead of "host->mmc". If the code sits in hot code path, this clean up also brings trvial performance improvement. Take the sdhci_post_req() for example: before the patch: ... 8d0: a9be7bfd stp x29, x30, [sp, #-32]! 8d4: 910003fd mov x29, sp 8d8: f9000bf3 str x19, [sp, #16] 8dc: f9400833 ldr x19, [x1, #16] 8e0: b9404261 ldr w1, [x19, #64] 8e4: 34000161 cbz w1, 910 <sdhci_post_req+0x50> 8e8: f9424400 ldr x0, [x0, #1160] 8ec: d2800004 mov x4, #0x0 // #0 8f0: b9401a61 ldr w1, [x19, #24] 8f4: b9403262 ldr w2, [x19, #48] 8f8: f9400000 ldr x0, [x0] 8fc: f278003f tst x1, #0x100 900: f9401e61 ldr x1, [x19, #56] 904: 1a9f17e3 cset w3, eq // eq = none 908: 11000463 add w3, w3, #0x1 90c: 94000000 bl 0 <dma_unmap_sg_attrs> ... After the patch: ... 8d0: a9be7bfd stp x29, x30, [sp, #-32]! 8d4: 910003fd mov x29, sp 8d8: f9000bf3 str x19, [sp, #16] 8dc: f9400833 ldr x19, [x1, #16] 8e0: b9404261 ldr w1, [x19, #64] 8e4: 34000141 cbz w1, 90c <sdhci_post_req+0x4c> 8e8: b9401a61 ldr w1, [x19, #24] 8ec: d2800004 mov x4, #0x0 // #0 8f0: b9403262 ldr w2, [x19, #48] 8f4: f9400000 ldr x0, [x0] 8f8: f278003f tst x1, #0x100 8fc: f9401e61 ldr x1, [x19, #56] 900: 1a9f17e3 cset w3, eq // eq = none 904: 11000463 add w3, w3, #0x1 908: 94000000 bl 0 <dma_unmap_sg_attrs> ... We saved one ldr instruction: "ldr x0, [x0, #1160]" Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210311174046.597d1951@xhacker.debian Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-03-30mmc: sdhci: Check for reset prior to DMA address unmapPradeep P V K
For data read commands, SDHC may initiate data transfers even before it completely process the command response. In case command itself fails, driver un-maps the memory associated with data transfer but this memory can still be accessed by SDHC for the already initiated data transfer. This scenario can lead to un-mapped memory access error. To avoid this scenario, reset SDHC (when command fails) prior to un-mapping memory. Resetting SDHC ensures that all in-flight data transfers are either aborted or completed. So we don't run into this scenario. Swap the reset, un-map steps sequence in sdhci_request_done(). Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Signed-off-by: Pradeep P V K <pragalla@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2021-02-20sdhci: stop poking into swiotlb internalsChristoph Hellwig
Use the proper API to query the max mapping size instead of guessing it based on swiotlb internals. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2020-12-04mmc: sdhci: Use more concise device_property_read_u64Jeremy Linton
Since we only need a single u64 the _array form is unnecessarily. Use device_property_read_u64 instead. Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20201125033630.603863-1-jeremy.linton@arm.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-11-24mmc: sdhci: Update firmware interface APIJeremy Linton
The device_* calls were added a few years ago to abstract DT/ACPI/fwnode firmware interfaces. Lets convert the two sdhci caps fields to use the generic calls rather than the OF specific ones. This has the side effect of allowing ACPI based devices to quirk themselves when the caps field is broken. Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Link: https://lore.kernel.org/r/20201120233831.447365-1-jeremy.linton@arm.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-10-15mmc: sdhci: Use Auto CMD Auto Select only when v4_mode is trueJisheng Zhang
sdhci-of-dwcmshc meets an eMMC read performance regression with below command after commit 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto Select support"): dd if=/dev/mmcblk0 of=/dev/null bs=8192 count=100000 Before the commit, the above command gives 120MB/s After the commit, the above command gives 51.3 MB/s So it looks like sdhci-of-dwcmshc expects Version 4 Mode for Auto CMD Auto Select. Fix the performance degradation by ensuring v4_mode is true to use Auto CMD Auto Select. Fixes: 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto Select support") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201015174115.4cf2c19a@xhacker.debian Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-05Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull MMC updates from Ulf Hansson: "MMC core: - Add a new host cap bit and a corresponding DT property, to support power cycling of the card by FW at system suspend/resume. - Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode - Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards - Convert the mmc-pwrseq DT bindings to the json-schema - Always allow the card detect uevent to be consumed by userspace MMC host controllers: - Convert a few DT bindings to the json-schema - mtk-sd: - Add support for command queue through cqhci - Add support for the MT6779 variant - renesas_sdhi_internal_dmac: - Fix dma unmapping in the error path - sdhci_am654: - Add support for the AM65x PG2.0 variant - Extend support for phys/clocks - sdhci-cadence: - Drop incorrect HW tuning for SD mode - sdhci-msm: - Add support for interconnect bandwidth scaling - Enable internal voltage control - Enable low power state for pinctrls - sdhci-of-at91: - Ludovic Desroches handovers maintenance to Eugen Hristev - sdhci-pci-gli: - Improve clock handling for GL975x - sdhci-pci-o2micro: - Add HW tuning for SDR104 mode - Fix support for O2 host controller Seabird1" * tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits) mmc: mediatek: make function msdc_cqe_disable() static MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev dt-bindings: mmc: mediatek: Add document for mt6779 mmc: mediatek: command queue support mmc: mediatek: refine msdc timeout api mmc: mediatek: add MT6779 MMC driver support mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1 mmc: via-sdmmc: use generic power management memstick: jmb38x_ms: use generic power management mmc: sdhci-cadence: do not use hardware tuning for SD mode mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x mmc: cqhci: Fix a print format for the task descriptor mmc: sdhci-of-arasan: fix timings allocation code mmc: sdhci: Fix a potential uninitialized variable dt-bindings: mmc: renesas,sdhi: convert to YAML dt-bindings: mmc: convert arasan sdhci bindings to yaml mmc: sdhci: Fix potential null pointer access while accessing vqmmc mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND dt-bindings: mmc: Add full-pwr-cycle-in-suspend property ...
2020-07-24mmc: sdhci: Fix a potential uninitialized variableDan Carpenter
Smatch complains that "ret" can be used without being initialized. drivers/mmc/host/sdhci.c 4383 if (!IS_ERR(mmc->supply.vqmmc)) { 4384 if (enable_vqmmc) { ^^^^^^^^^^^^ 4385 ret = regulator_enable(mmc->supply.vqmmc); ^^^^^ 4386 host->sdhci_core_to_disable_vqmmc = !ret; 4387 } "ret" is only initialized when "enable_vqmmc" is true. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200714141410.GB314989@mwanda Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-07-16treewide: Remove uninitialized_var() usageKees Cook
Using uninitialized_var() is dangerous as it papers over real bugs[1] (or can in the future), and suppresses unrelated compiler warnings (e.g. "unused variable"). If the compiler thinks it is uninitialized, either simply initialize the variable or make compiler changes. In preparation for removing[2] the[3] macro[4], remove all remaining needless uses with the following script: git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \ xargs perl -pi -e \ 's/\buninitialized_var\(([^\)]+)\)/\1/g; s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;' drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid pathological white-space. No outstanding warnings were found building allmodconfig with GCC 9.3.0 for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64, alpha, and m68k. [1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/ [2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/ [3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/ [4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/ Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5 Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs Signed-off-by: Kees Cook <keescook@chromium.org>
2020-07-13mmc: sdhci: Fix potential null pointer access while accessing vqmmcVeerabhadrarao Badiganti
Don't access vqmmc regulator handler, if it's already invalidated. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link: https://lore.kernel.org/r/1594300408-17658-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-07-13mmc: sdhci: Allow platform controlled voltage switchingVijay Viswanath
If vendor platform drivers are controlling whole logic of voltage switching, then sdhci driver no need control vqmmc regulator. So skip enabling/disable vqmmc from SDHC driver. Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28Merge branch 'fixes' into nextUlf Hansson
2020-05-28mmc: sdhci-msm: Introduce new ops to dump vendor specific registersSarthak Garg
Introduce new sdhci ops to dump vendor specific registers in the sdhci_dumpregs during error. Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1590139950-7288-8-git-send-email-sartgarg@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: add quirks for be to le byte swappingAngelo Dureghello
Some controller as the ColdFire eshdc may require an endianness byte swap, because DMA read endianness is not configurable. Facilitate using the bounce buffer for this by adding ->copy_to_bounce_buffer(). Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200518191742.1251440-2-angelo.dureghello@timesys.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: use FIELD_GET/PREP for current capabilities bit masksMasahiro Yamada
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete the shift macros and use GENMASK() for the touched macros. Note that, this has the side-effect of changing the constants to 64-bit on 64-bit platforms. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Link: https://lore.kernel.org/r/20200511062828.1791484-1-yamada.masahiro@socionext.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: host: Drop redundant MMC_CAP_ERASEUlf Hansson
The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard and trim operations are now always supported. Therefore, drop the bit and move all mmc hosts away from using it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-05-28mmc: sdhci: add spin lock for sdhci_set_default_irqs in sdhci_initHaibo Chen
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX, we meet system hang. This hang happened during the usdhc runtime resume, in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt (SDHCI_INT_CARD_INT) triggered just after the host->ier update and before the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip the call of sdio_signal_irq() because current host->ier do not set the SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered, let the system stuck in irq handle, can't response any other thread. This patch add spin lock for the sdhci_set_default_irqs to fix this issue. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: host: sdhci: Implement the request_atomic() APIBaolin Wang
Implement the request_atomic() ops for the sdhci driver to process one request in the atomic context if the card is nonremovable. Moreover, we should return BUSY flag if controller has not released the inhibit bits to allow HSQ trying to send request again in non-atomic context. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Baolin Wang <baolin.wang7@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/9ed34afa9fb42e0c234065cac5401d7826942b55.1586744073.git.baolin.wang7@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: Reduce maximum time under spinlock in sdhci_send_command()Adrian Hunter
Spending time under spinlock increases IRQ latencies and also response times because preemption is disabled. sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits to clear. In general inhibit bits will not be set, but there may be corner cases, especially in the face of errors, where waiting helps. There might also be dysfunctional hardware that needs the waiting. So retain the legacy behaviour but do not wait for inhibit bits while under spinlock. Instead adjust the logic to enable waiting while not under spinlock. That is mostly straight forward, but in the interrupt handler it requires deferring an "inhibited" command to the IRQ thread where sleeping is allowed. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: Tidy sdhci_request() a bitAdrian Hunter
In preparation for further changes, tidy sdhci_request() a bit. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/20200412090349.1607-5-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: Remove unneeded forward declaration of sdhci_finish_data()Adrian Hunter
sdhci_finish_data() is defined before it is referenced, so forward declaration is not necessary. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/20200412090349.1607-4-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: Stop exporting sdhci_send_command()Adrian Hunter
sdhci_send_command() has not been used outside of sdhci.c for many years. Stop exporting it. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/20200412090349.1607-3-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: Add helpers for the auto-CMD23 flagAdrian Hunter
Add 2 helper functions to make the use of the auto-CMD23 flag more readable. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/20200412090349.1607-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: host: Prepare host drivers for mmc_regulator_set_vqmmc() returning > 0Marek Vasut
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would happen if the signal voltage switch did NOT happen, because the voltage was already set correctly. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de [Ulf: Re-worked/simplified the code a bit] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-28mmc: sdhci: use FIELD_GET/PREP for capabilities bit masksMasahiro Yamada
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete the shift macros and use GENMASK() for the touched macros. Note that, this has the side-effect of changing the constants to 64-bit on 64-bit platforms. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200408072105.422-2-yamada.masahiro@socionext.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-18mmc: sdhci: Fix SDHCI_QUIRK_BROKEN_CQEAdrian Hunter
Previous to commit 511ce378e16f07 ("mmc: Add MMC host software queue support"), removing MMC_CAP2_CQE was enough to disable command queuing, but now the cqe_ops must also be NULL otherwise ->cqe_enable() will be called. Fix SDHCI_QUIRK_BROKEN_CQE to do that. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: 511ce378e16f07 ("mmc: Add MMC host software queue support") Link: https://lore.kernel.org/r/20200518120939.1399-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24mmc: sdhci: use FIELD_GET for preset value bit masksMasahiro Yamada
Use the FIELD_GET macro to get access to the register fields. Delete the shift macros. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Link: https://lore.kernel.org/r/20200312110050.21732-1-yamada.masahiro@socionext.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()Nicolas Saenz Julienne
Some controllers diverge from the standard way of setting power and need their bus voltage register to be configured regardless of the whether they use regulators. As this is a common pattern across sdhci hosts, create a helper function. Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200306174413.20634-2-nsaenzjulienne@suse.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24mmc: sdhci: do not enable card detect interrupt for gpio cd typeHaibo Chen
Except SDHCI_QUIRK_BROKEN_CARD_DETECTION and MMC_CAP_NONREMOVABLE, we also do not need to handle controller native card detect interrupt for gpio cd type. If we wrong enabled the card detect interrupt for gpio case, it will cause a lot of unexpected card detect interrupts during data transfer which should not happen. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/1582100563-20555-2-git-send-email-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24mmc: host: sdhci: Add a variable to defer to complete requests if neededBaolin Wang
When using the host software queue, it will trigger the next request in irq handler without a context switch. But the sdhci_request() can not be called in interrupt context when using host software queue for some host drivers, due to the get_cd() ops can be sleepable. But for some host drivers, such as Spreadtrum host driver, the card is nonremovable, so the get_cd() ops is not sleepable, which means we can complete the data request and trigger the next request in irq handler to remove the context switch for the Spreadtrum host driver. As suggested by Adrian, we should introduce a request_atomic() API to indicate that a request can be called in interrupt context to remove the context switch when using mmc host software queue. But this should be done in another thread to convert the users of mmc host software queue. Thus we can introduce a variable in struct sdhci_host to indicate that we will always to defer to complete requests when using the host software queue. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/e693e7a29beb3c1922b333f4603ea81f43d5c5b1.1581478568.git.baolin.wang7@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-03-24mmc: host: sdhci: Add request_done ops for struct sdhci_opsBaolin Wang
Add request_done ops for struct sdhci_ops as a preparation in case some host controllers have different method to complete one request, such as supporting request completion of MMC software queue. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Baolin Wang <baolin.wang7@gmail.com> Link: https://lore.kernel.org/r/1539c801c8bbdbcd1d86f8c2dab375f5803c765a.1581478568.git.baolin.wang7@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-24mmc: sdhci: Let a vendor driver supply and update ADMA descriptor sizeVeerabhadrarao Badiganti
Let a vendor driver supply the maximum descriptor size that it can operate on. ADMA descriptor table would be allocated using this supplied size. If any SD Host controller is of version prior to v4.10 spec but supports 16byte descriptor, this change allows them to supply correct descriptor size for ADMA table allocation. Also let a vendor driver update the descriptor size by overriding sdhc_host->desc_size if it has to operates on a different descriptor sizes in different conditions. Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20mmc: sdhci: fix an issue of mixing different typesChunyan Zhang
Fix an issue reported by sparse, since mixed types of parameters are used on calling dmaengine_prep_slave_sg(). Fixes: 36e1da441fec (mmc: sdhci: add support for using external DMA devices) Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200120033223.897-1-zhang.chunyan@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20Merge branch 'fixes' into nextUlf Hansson
2020-01-20mmc: sdhci: fix minimum clock rate for v3 controllerMichał Mirosław
For SDHCIv3+ with programmable clock mode, minimal clock frequency is still base clock / max(divider). Minimal programmable clock frequency is always greater than minimal divided clock frequency. Without this patch, SDHCI uses out-of-spec initial frequency when multiplier is big enough: mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz [for 480 MHz source clock divided by 1024] The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode. Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present Cc: <stable@vger.kernel.org> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20mmc: sdhci: Refactor sdhci_set_timeout()Faiz Abbas
Refactor sdhci_set_timeout() such that platform drivers can do some functionality in a set_timeout() callback and then call __sdhci_set_timeout() to complete the operation. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20mmc: sdhci: Convert sdhci_set_timeout_irq() to non-staticFaiz Abbas
Export sdhci_set_timeout_irq() so that it is accessible from platform drivers. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20mmc: sdhci: add support for using external DMA devicesChunyan Zhang
Some standard SD host controllers can support both external dma controllers as well as ADMA/SDMA in which the SD host controller acts as DMA master. TI's omap controller is the case as an example. Currently the generic SDHCI code supports ADMA/SDMA integrated in the host controller but does not have any support for external DMA controllers implemented using dmaengine, meaning that custom code is needed for any systems that use an external DMA controller with SDHCI. Fixes by Faiz Abbas <faiz_abbas@ti.com>: 1. Map scatterlists before dmaengine_prep_slave_sg() 2. Use dma_async() functions inside of the send_command() path and call terminate_sync() in non-atomic context in case of an error. Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-4-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-01-20mmc: sdhci: Factor out some operations set to their own functionsFaiz Abbas
In preparation for adding external dma support, factor out data initialization, block info and mrq_done to their own functions. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Tested-by: Baolin Wang <baolin.wang7@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-3-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-18Merge branch 'fixes' into nextUlf Hansson
2019-12-18mmc: sdhci: Add a quirk for broken command queuingAdrian Hunter
Command queuing has been reported broken on some systems based on Intel GLK. A separate patch disables command queuing in some cases. This patch adds a quirk for broken command queuing, which enables users with problems to disable command queuing using sdhci module parameters for quirks. Fixes: 8ee82bda230f ("mmc: sdhci-pci: Add CQHCI support for Intel GLK") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-16Merge branch 'fixes' into nextUlf Hansson
2019-12-16mmc: sdhci: Update the tuning failed messages to pr_debug levelFaiz Abbas
Tuning support in DDR50 speed mode was added in SD Specifications Part1 Physical Layer Specification v3.01. Its not possible to distinguish between v3.00 and v3.01 from the SCR and that is why since commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode") tuning failures are ignored in DDR50 speed mode. Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this error gets printed during enumeration and also if retune is triggered at any time during operation. Update the printk level to pr_debug so that these errors don't lead to false error reports. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Cc: stable@vger.kernel.org # v4.4+ Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-16mmc: sdhci: fix up CMD12 sendingYangbo Lu
The STOP command is disabled for multiple blocks r/w commands with auto CMD12, when start to send. However, if there is data error, software still needs to send CMD12 according to SD spec. This patch is to allow software CMD12 sending for this case. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191114111814.35199-1-yangbo.lu@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-12-16mmc: sdhci: Update the tuning failed messages to pr_debug levelFaiz Abbas
Tuning support in DDR50 speed mode was added in SD Specifications Part1 Physical Layer Specification v3.01. Its not possible to distinguish between v3.00 and v3.01 from the SCR and that is why since commit 4324f6de6d2e ("mmc: core: enable CMD19 tuning for DDR50 mode") tuning failures are ignored in DDR50 speed mode. Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this error gets printed during enumeration and also if retune is triggered at any time during operation. Update the printk level to pr_debug so that these errors don't lead to false error reports. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Cc: stable@vger.kernel.org # v4.4+ Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 14:04:55 +0000