| Age | Commit message (Collapse) | Author |
|---|
|
commit 565fe150624ee77dc63a735cc1b3bff5101f38a3 upstream.
Currently the offset into the device when looking for OTP
bits can go outside of the address of the MTD NOR devices,
and if that memory isn't readable, bad things happen
on the IXP4xx (added prints that illustrate the problem before
the crash):
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x00000100
ixp4xx_copy_from copy from 0x00000100 to 0xc880dd78
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x12000000
ixp4xx_copy_from copy from 0x12000000 to 0xc880dd78
8<--- cut here ---
Unable to handle kernel paging request at virtual address db000000
[db000000] *pgd=00000000
(...)
This happens in this case because the IXP4xx is big endian and
the 32- and 16-bit fields in the struct cfi_intelext_otpinfo are not
properly byteswapped. Compare to how the code in read_pri_intelext()
byteswaps the fields in struct cfi_pri_intelext.
Adding a small byte swapping loop for the OTP in read_pri_intelext()
and the crash goes away.
The problem went unnoticed for many years until I enabled
CONFIG_MTD_OTP on the IXP4xx as well, triggering the bug.
Cc: stable@vger.kernel.org
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231020-mtd-otp-byteswap-v4-1-0d132c06aa9d@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5a985960a4dd041c21dbe9956958c1633d2da706 ]
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful by
checking the pointer validity.
Fixes: 1e4d3ba66888 ("mtd: rawnand: meson: fix the clock")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231019065548.318443-1-yiyang13@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74ac5b5e2375f1e8ef797ac7770887e9969f2516 ]
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful by
checking the pointer validity.
Fixes: 0b1039f016e8 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231019065537.318391-1-yiyang13@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a1166c27d4e53186e6bf9147ea6db9cd1d65847 ]
Add the missing check for platform_get_irq() and return error code
if it fails.
Fixes: d7d9f8ec77fe ("mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821084046.217025-1-yiyang13@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 6792b7fce610bcd1cf3e07af3607fe7e2c38c1d8 upstream.
When the exact mapping type driver was not available, the old
physmap_of_core driver fell back to mapping the region as ROM.
Unfortunately this feature was lost when the DT and pdata cases were
merged. Revive this useful feature.
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/550e8c8c1da4c4baeb3d71ff79b14a18d4194f9e.1693407371.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9836a987860e33943945d4b257729a4f94eae576 upstream.
Valid bitmask is 0x70 in the status register.
Fixes: a508e8875e13 ("mtd: spinand: Add initial support for Micron MT29F2G01ABAGD")
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230905145637.139068-1-mmkurbanov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a4a893dbb19e229db3b753f0462520b561dee98 upstream.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e01d5254698ea3d18e09d96b974c762328352cd upstream.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9777cc13fd2c3212618904636354be60835e10bb upstream.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5279f4a9eed3ee7d222b76511ea7a22c89e7eefd upstream.
We currently provide the physical address of the DMA region
rather than the output of dma_map_resource() which is obviously wrong.
Fixes: 7330fc505af4 ("mtd: rawnand: qcom: stop using phys_to_dma()")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bibek Kumar Patro <quic_bibekkum@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230913070702.12707-1-quic_bibekkum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 017c73a34a661a861712f7cc1393a123e5b2208c ]
There exists mtd devices with zero erasesize, which will trigger a
divide-by-zero exception while attaching ubi device.
Fix it by refusing attaching if mtd's erasesize is 0.
Fixes: 801c135ce73d ("UBI: Unsorted Block Images")
Reported-by: Yu Hao <yhao016@ucr.edu>
Link: https://lore.kernel.org/lkml/977347543.226888.1682011999468.JavaMail.zimbra@nod.at/T/
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2ec2839a9062db8a592525a3fdabd42dcd9a3a9b upstream.
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Fixes: decba6d47869 ("mtd: brcmnand: Add v7.2 controller support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-2-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cc0a598b944816f2968baf2631757f22721b996 upstream.
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Fixes: 9d2ee0a60b8b ("mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-3-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83e824a4a595132f9bd7ac4f5afff857bfc5991e upstream.
The Winbond "w25q128" (actual vendor name W25Q128JV) has
exactly the same flags as the sibling device "w25q128jv".
The devices both require unlocking to enable write access.
The actual product naming between devices vs the Linux
strings in winbond.c:
0xef4018: "w25q128" W25Q128JV-IN/IQ/JQ
0xef7018: "w25q128jv" W25Q128JV-IM/JM
The latter device, "w25q128jv" supports features named DTQ
and QPI, otherwise it is the same.
Not having the right flags has the annoying side effect
that write access does not work.
After this patch I can write to the flash on the Inteno
XG6846 router.
The flash memory also supports dual and quad SPI modes.
This does not currently manifest, but by turning on SFDP
parsing, the right SPI modes are emitted in
/sys/kernel/debug/spi-nor/spi1.0/capabilities
for this chip, so we also turn on this.
Since we now have determined that SFDP parsing works on
the device, we also detect the geometry using SFDP.
After this dmesg and sysfs says:
[ 1.062401] spi-nor spi1.0: w25q128 (16384 Kbytes)
cat erasesize
65536
(16384*1024)/65536 = 256 sectors
spi-nor sysfs:
cat jedec_id
ef4018
cat manufacturer
winbond
cat partname
w25q128
hexdump -v -C sfdp
00000000 53 46 44 50 05 01 00 ff 00 05 01 10 80 00 00 ff
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
00000080 e5 20 f9 ff ff ff ff 07 44 eb 08 6b 08 3b 42 bb
00000090 fe ff ff ff ff ff 00 00 ff ff 40 eb 0c 20 0f 52
000000a0 10 d8 00 00 36 02 a6 00 82 ea 14 c9 e9 63 76 33
000000b0 7a 75 7a 75 f7 a2 d5 5c 19 f7 4d ff e9 30 f8 80
Cc: stable@vger.kernel.org
Suggested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230718-spi-nor-winbond-w25q128-v5-1-a73653ee46c3@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d53244186c9ac58cb88d76a0958ca55b83a15cd upstream.
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-5-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e66dd317194daae0475fe9e5577c80aa97f16cb9 upstream.
When executing a NAND command within the panic write path, wait for any
pending command instead of calling BUG_ON to avoid crashing while
already crashing.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-4-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a5a88125d00612586e941ae13e7fcf36ba8f18a7 ]
In fsmc_nand_resume(), the return value of clk_prepare_enable() should be
checked since it might fail.
Fixes: e25da1c07dfb ("mtd: fsmc_nand: Add clk_{un}prepare() support")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230817115839.10192-1-yiyang13@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f01d8155a92e33cdaa85d20bfbe6c441907b3c1f ]
spi_nor_write_16bit_sr_and_check() should also check if bus width is
4 before setting QE bit.
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Suggested-by: Michael Walle <michael@walle.cc>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230818064524.1229100-2-hsinyi@chromium.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60177390fa061c62d156f4a546e3efd90df3c183 ]
brcmnand controller can only access the flash spare area up to certain
bytes based on the ECC level. It can be less than the actual flash spare
area size. For example, for many NAND chip supporting ECC BCH-8, it has
226 bytes spare area. But controller can only uses 218 bytes. So brcmand
driver overrides the mtd oobsize with the controller's accessible spare
area size. When the nand base driver utilizes the nand_device object, it
resets the oobsize back to the actual flash spare aprea size from
nand_memory_organization structure and controller may not able to access
all the oob area as mtd advises.
This change fixes the issue by overriding the oobsize in the
nand_memory_organization structure to the controller's accessible spare
area size.
Fixes: a7ab085d7c16 ("mtd: rawnand: Initialize the nand_device object")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-6-william.zhang@broadcom.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6abce60338aa2080973cd95be0aedad528bb41f ]
'op-cs' is copied in 'fun->mchip_number' which is used to access the
'mchip_offsets' and the 'rnb_gpio' arrays.
These arrays have NAND_MAX_CHIPS elements, so the index must be below this
limit.
Fix the sanity check in order to avoid the NAND_MAX_CHIPS value. This
would lead to out-of-bound accesses.
Fixes: 54309d657767 ("mtd: rawnand: fsl_upm: Implement exec_op()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cd01cba1c7eda58bdabaae174c78c067325803d2.1689803636.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea690ad78dd611e3906df5b948a516000b05c1cb ]
Currently, read/write_page_hwecc() and read/write_page_raw() are not
aligned: there is a mismatch in the OOB bytes which are not
read/written at the same offset in both cases (raw vs. hwecc).
This is a real problem when relying on the presence of the Page
Addresses (PA) when using the NAND chip as a boot device, as the
BootROM expects additional data in the OOB area at specific locations.
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page. Pages are written in a pattern depending on the NAND chip ID.
Generate boot block page address and pattern for hwecc in user space
and copy PA data to/from the already reserved last 4 bytes before ECC
in the chip->oob_poi data layout.
Align the different helpers. This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/5e782c08-862b-51ae-47ff-3299940928ca@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0ca3b92b7a6f42841ea9da8492aaf649db79780 ]
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page.
The currently advertised free OOB area starts at offset 6, like
if 4 PA bytes were located right after the BBM. This is wrong as the
PA bytes are located right before the ECC bytes.
Fix the layout by allowing access to all bytes between the BBM and the
PA bytes instead of reserving 4 bytes right after the BBM.
This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/d202f12d-188c-20e8-f2c2-9cc874ad4d22@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d8403b9eeee66d5dd81ecb9445800b108c267ce3 ]
Once the ECC word endianness is converted to BE32, we force cast it
to u32 so we can use elm_write_reg() which in turn uses writel().
Fixes below sparse warnings:
drivers/mtd/nand/raw/omap_elm.c:180:37: sparse: expected unsigned int [usertype] val
drivers/mtd/nand/raw/omap_elm.c:180:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:185:37: sparse: expected unsigned int [usertype] val
drivers/mtd/nand/raw/omap_elm.c:185:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:190:37: sparse: expected unsigned int [usertype] val
drivers/mtd/nand/raw/omap_elm.c:190:37: sparse: got restricted __be32 [usertype]
>> drivers/mtd/nand/raw/omap_elm.c:200:40: sparse: sparse: restricted __be32 degrades to integer
drivers/mtd/nand/raw/omap_elm.c:206:39: sparse: sparse: restricted __be32 degrades to integer
drivers/mtd/nand/raw/omap_elm.c:210:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:210:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:213:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:213:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:216:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:216:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:219:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:219:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:222:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:222:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:225:37: sparse: expected unsigned int [assigned] [usertype] val
drivers/mtd/nand/raw/omap_elm.c:225:37: sparse: got restricted __be32 [usertype]
drivers/mtd/nand/raw/omap_elm.c:228:39: sparse: sparse: restricted __be32 degrades to integer
Fixes: bf22433575ef ("mtd: devices: elm: Add support for ELM error correction")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306212211.WDXokuWh-lkp@intel.com/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230624184021.7740-1-rogerq@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7e6b04f9238eab0f684fafd158c1f32ea65b9eaa upstream.
It is incorrect to calculate number of OOB bytes for ECC engine using
some "already known" ECC step size (1024 bytes here). Number of such
bytes for ECC engine must be whole OOB except 2 bytes for bad block
marker, while proper ECC step size and strength will be selected by
ECC logic.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230705065211.293500-1-AVKrasnov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8544cda94dae6be3f1359539079c68bb731428b1 upstream.
Reading ECC status is failing.
tx58cxgxsxraix_ecc_get_status() is using on-stack buffer
for SPINAND_GET_FEATURE_OP() output. It is not suitable
for DMA needs of spi-mem.
Fix this by using the spi-mem operations dedicated buffer
spinand->scratchbuf.
See
spinand->scratchbuf:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/mtd/spinand.h?h=v6.3#n418
spi_mem_check_op():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/spi/spi-mem.c?h=v6.3#n199
Fixes: 10949af1681d ("mtd: spinand: Add initial support for Toshiba TC58CVG2S0H")
Cc: stable@vger.kernel.org
Signed-off-by: Olivier Maignial <olivier.maignial@hotmail.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/DB4P250MB1032553D05FBE36DEE0D311EFE23A@DB4P250MB1032.EURP250.PROD.OUTLOOK.COM
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98480a181a08ceeede417e5b28f6d0429d8ae156 upstream.
Meson NAND controller requires 8 bytes alignment for DMA addresses,
otherwise it "aligns" passed address by itself thus accessing invalid
location in the provided buffer. This patch makes unaligned buffers to
be reallocated to become valid.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230615080815.3291006-1-AVKrasnov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 085679b15b5af65f9610f619afde41da0f966194 upstream.
Commit dd5c672d7ca9 ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
removes config ARCH_BCM4908 as config ARCH_BCMBCA has the same intent.
Probably due to concurrent development, commit 002181f5b150 ("mtd: parsers:
add Broadcom's U-Boot parser") introduces 'Broadcom's U-Boot partition
parser' that depends on ARCH_BCM4908, but this use was not visible during
the config refactoring from the commit above. Hence, these two changes
create a reference to a non-existing config symbol.
Adjust the MTD_BRCM_U_BOOT definition to refer to ARCH_BCMBCA instead of
ARCH_BCM4908 to remove the reference to the non-existing config symbol
ARCH_BCM4908.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221116124932.4748-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ea923f443350c8c5cca6eef5b748d52b903f46c upstream.
The addition of the mtdchar_read_ioctl() function caused the stack usage
of mtdchar_ioctl() to grow beyond the warning limit on 32-bit architectures
with gcc-13:
drivers/mtd/mtdchar.c: In function 'mtdchar_ioctl':
drivers/mtd/mtdchar.c:1229:1: error: the frame size of 1488 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Mark both the read and write portions as noinline_for_stack to ensure
they don't get inlined and use separate stack slots to reduce the
maximum usage, both in the mtdchar_ioctl() and combined with any
of its callees.
Fixes: 095bb6e44eb1 ("mtdchar: add MEMREAD ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230417205654.1982368-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c4d28e30a8d0b979e4029465ab8f312ab6ce2644 ]
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a6f4d346f3bad9c68b4a87701eb3f7978542d57 ]
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 650a8884a364ff2568b51cde9009cfd43cdae6ad ]
A few functions provide an empty interface definition when
CONFIG_MTD_NAND_INGENIC_ECC is disabled, but they are accidentally
defined as global functions in the header:
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:39:5: error: no previous prototype for 'ingenic_ecc_calculate'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:46:5: error: no previous prototype for 'ingenic_ecc_correct'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:53:6: error: no previous prototype for 'ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:57:21: error: no previous prototype for 'of_ingenic_ecc_get'
Turn them into 'static inline' definitions instead.
Fixes: 15de8c6efd0e ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230516202133.559488-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
flash
[ Upstream commit 4199c1719e24e73be0acc8b0146fc31ad8af9771 ]
Infineon(Cypress) SEMPER NOR flash family has on-die ECC and its program
granularity is 16-byte ECC data unit size. JFFS2 supports write buffer
mode for ECC'd NOR flash. Provide a way to clear the MTD_BIT_WRITEABLE
flag in order to enable JFFS2 write buffer mode support.
Fixes: b6b23833fc42 ("mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/a1cc128e094db4ec141f85bd380127598dfef17e.1680760742.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
flash
[ Upstream commit 9fd0945fe6fadfb6b54a9cd73be101c02b3e8134 ]
Infineon(Cypress) SEMPER NOR flash family has on-die ECC and its program
granularity is 16-byte ECC data unit size. JFFS2 supports write buffer
mode for ECC'd NOR flash. Provide a way to clear the MTD_BIT_WRITEABLE
flag in order to enable JFFS2 write buffer mode support.
A new SNOR_F_ECC flag is introduced to determine if the part has on-die
ECC and if it has, MTD_BIT_WRITEABLE is unset.
In vendor specific driver, a common cypress_nor_ecc_init() helper is
added. This helper takes care for ECC related initialization for SEMPER
flash family by setting up params->writesize and SNOR_F_ECC.
Fixes: c3266af101f2 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/d586723f6f12aaff44fbcd7b51e674b47ed554ed.1680760742.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4eddee70140b3ae183398b246a609756546c51f1 ]
Introduce a new (no SFDP) flag for the feature that we are about to
support: Read While Write. This means, if the chip has several banks and
supports RWW, once a page of data to write has been transferred into the
chip's internal SRAM, another read operation happening on a different
bank can be performed during the tPROG delay.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230328154105.448540-7-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Stable-dep-of: 9fd0945fe6fa ("mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1799cd8540b67b88514c82f5fae1c75b986bcbd8 ]
SFDP table of some flash chips do not advertise support of Quad Input
Page Program even though it has support. Use flags and add hardware
cap for these chips.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: move pp setting in spi_nor_init_default_params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-2-sudip.mukherjee@sifive.com
Stable-dep-of: 9fd0945fe6fa ("mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db391efe765cc6cfc0ffc8d8ef146dc8e6816a7e ]
Read, Page Program, and Sector Erase settings are done in SFDP so we can
remove NO_SFDP_FLAGS from s28hs512t info. Since the default_init() is no
longer called after removing NO_SFDP_FLAGS, the initialization in the
default_init() is moved to late_init().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/12e468992f5d0cbd474abff3203100cc8163d4e5.1661915569.git.Takahiro.Kuwano@infineon.com
Stable-dep-of: 9fd0945fe6fa ("mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
address mode
commit 37513c56139b79dd43c1774513c28f8ab2b05224 upstream.
The bug was obswerved while reading code. There are not many users of
addr_mode_nbytes. Anyway, we should update the flash's current address
mode when changing the address mode, fix it. We don't care for now about
the set_4byte_addr_mode(nor, false) from spi_nor_restore(), as it is
used at driver remove and shutdown.
Fixes: d7931a215063 ("mtd: spi-nor: core: Track flash's internal address mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230331074606.3559258-9-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0489f6e221f5ddee6cb3bd51b992b790c5fa4b9 upstream.
If mtd_otp_nvmem_add() fails, the partitions won't be removed
because there is simply no call to del_mtd_partitions().
Unfortunately, add_mtd_partitions() will print all partitions to
the kernel console. If mtd_otp_nvmem_add() returns -EPROBE_DEFER
this would print the partitions multiple times to the kernel
console. Instead move mtd_otp_nvmem_add() to the beginning of the
function.
Fixes: 4b361cfa8624 ("mtd: core: add OTP nvmem provider support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8bd1d24e6ca3c599dd455b0e1b22f77bab8290eb upstream.
The master MTD will only have an associated device if
CONFIG_MTD_PARTITIONED_MASTER is set, thus we cannot use dev_err() on
mtd->dev. Instead use the parent device which is the physical flash
memory.
Fixes: 4b361cfa8624 ("mtd: core: add OTP nvmem provider support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cd9ceaa5282ff10ea20a7fbadde5a476a1cc99e upstream.
Commit c048b60d39e1 ("mtd: core: provide unique name for nvmem device")
tries to give the nvmem device a unique name, but fails badly if the mtd
device doesn't have a "struct device" associated with it, i.e. if
CONFIG_MTD_PARTITIONED_MASTER is not set. This will result in the name
"(null)-user-otp", which is not unique. It seems the best we can do is
to use the compatible name together with a unique identifier added by
the nvmem subsystem by using NVMEM_DEVID_AUTO.
Fixes: c048b60d39e1 ("mtd: core: provide unique name for nvmem device")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31a149d5c13c4cbcf97de3435817263a2d8c9d6e upstream.
The commit 2d78aee426d8 ("UBI: simplify LEB write and atomic LEB change code")
adds helper function, try_write_vid_and_data(), to simplify the code, but this
helper function has bug, it will return 0 (success) when ubi_io_write_vid_hdr()
or the ubi_io_write_data() return error number (-EIO, etc), because the return
value of ubi_wl_put_peb() will overwrite the original return value.
This issue will cause unexpected data loss issue, because the caller of this
function and UBIFS willn't know the data is lost.
Fixes: 2d78aee426d8 ("UBI: simplify LEB write and atomic LEB change code")
Cc: stable@vger.kernel.org
Signed-off-by: Wang YanQing <udknight@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ec738ca127d07ecac6afae36e2880341ec89150e ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To solve this, remove the
lookup and create the directory on the first device found, and then
remove it when the module is unloaded.
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230208160230.2179905-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f773f0a331d6c41733b17bebbc1b6cae12e016f5 ]
During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.
ubi bgt other task
do_work
down_read(&ubi->work_sem) ubi_update_fastmap
erase_worker # Blocked by down_read
__erase_worker down_write(&ubi->work_sem)
schedule_erase
schedule_ubi_work
down_read(&ubi->work_sem)
Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).
Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1e020e1b96afdecd20680b5b5be2a6ffc3d27628 upstream.
Following process will make ubi attaching failed since commit
1b42b1a36fc946 ("ubi: ensure that VID header offset ... size"):
ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048" # set vid_hdr offset as 2048 (one page)
(dmesg):
ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
UBI error: cannot attach mtd0
UBI error: cannot initialize UBI, error -22
Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.
Fixes: 1b42b1a36fc946 ("ubi: ensure that VID header offset ... size")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ddbb664b6ab8de7dffa388ae0c88cd18616494e5 upstream.
Use timings.mode value instead of checking tRC_min timing
for EDO mode support.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 2cd457f328c1 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Cc: stable@vger.kernel.org #v5.10+
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328155819.225521-3-christophe.kerello@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f71e0e329c152c7f11ddfd97ffc62aba152fad3f upstream.
Remove the EDO mode support from as the FMC2 controller does not
support the feature.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 2cd457f328c1 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Cc: stable@vger.kernel.org #v5.4+
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328155819.225521-2-christophe.kerello@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93942b70461574ca7fc3d91494ca89b16a4c64c7 upstream.
Valid mask is 0x3FFF, without this patch the following problems were
found:
1) [ 0.938914] Could not find a valid ONFI parameter page, trying
bit-wise majority to recover it
[ 0.947384] ONFI parameter recovery failed, aborting
2) Read with disabled ECC mode was broken.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/3794ffbf-dfea-e96f-1f97-fe235b005e19@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c3089601f064d80b3838eceb711fcac04bceaad upstream.
mtd_read() may return -EUCLEAN in case of corrected bit-flips.This
particular condition should not be treated like an error.
Signed-off-by: Bang Li <libang.linuxer@gmail.com>
Fixes: e47f68587b82 ("mtd: check for max_bitflips in mtd_read_oob()")
Cc: <stable@vger.kernel.org> # v3.7
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328163012.4264-1-libang.linuxer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e732e39ed9929c05fd219035bc9653ba4100d4fa ]
'info_buf' memory is cached and driver polls ECC bit in it. This bit
is set by the NAND controller. If 'usleep_range()' returns before device
sets this bit, 'info_buf' will be cached and driver won't see update of
this bit and will loop forever.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/d4ef0bd6-816e-f6fa-9385-f05f775f0ae2@sberdevices.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
is used
[ Upstream commit 75dce6a941e3f16c3b4878c8b2f46d5d07c619ce ]
wait_for_completion_timeout() and readl_poll_timeout() don't handle their
return value the same way.
wait_for_completion_timeout() returns 0 on time out (and >0 in all other
cases)
readl_poll_timeout() returns 0 on success and -ETIMEDOUT upon a timeout.
In order for the error handling path to work in both cases, the logic
against wait_for_completion_timeout() needs to be inverted.
Fixes: 48e6633a9fa2 ("mtd: nand: mxic-ecc: Add Macronix external ECC engine support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/beddbc374557e44ceec897e68c4a5d12764ddbb9.1676459308.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
