| Age | Commit message (Collapse) | Author |
|---|
|
Add enic ndo_{set|get}_vf_port ops to support setting/getting
port-profile for enic dynamic devices. Enic dynamic devices are just like
normal enic eth devices except dynamic enics require an extra configuration
step to assign a port-profile identifier to the interface before the
interface is useable. Once a port-profile is assigned, link comes up on the
interface and is ready for I/O. The port-profile is used to configure the
network port assigned to the interface. The network port configuration
includes VLAN membership, QoS policies, and port security settings typical
of a data center network.
A dynamic enic initially has a zero-mac address. Before a port-profile is
assigned, a valid non-zero unicast mac address should be assign to the
dynamic enic interface.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/stmmac/stmmac_main.c
drivers/net/wireless/wl12xx/wl1271_cmd.c
drivers/net/wireless/wl12xx/wl1271_main.c
drivers/net/wireless/wl12xx/wl1271_spi.c
net/core/ethtool.c
net/mac80211/scan.c
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
1) Change enic driver description to "Cisco VIC Ethernet NIC Driver"
2) Fix tab space
3) Update MAINTAINERS list
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add wrapper functions vnic_dev_notify_setcmd and vnic_dev_notify_unsetcmd
for firmware notify commands.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware does not honor vlan filters from the host and so the driver does
not need to advertise this.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The timeout for hardware Tx and Rx queue disable operations is increased to
work-around an erratum for "unnamed" chipset where a DMA completion may take
upto 10ms. We have to wait atleast this long for hardware to signal that Tx
and Rx queues are quiesced.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last bit written to a completion descriptor by hardware is the color
bit. Driver must read all other descriptor fields only after reading the
color bit to avoid reading stale descriptor fields. There is a rmb() after
reading the color bit to avoid any compiler/cpu reordering of the reads.
The color bit is the generation bit that toggles each pass through the
completion descriptor ring.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some misc changes to cleanup whitespace issues and fix/remove some #define
HW defintions.
1) fix some whitespace issues
2) more verbose err msg when resources aren't available to configure vnic
3) remove unused #define
4) fix RSS #define rss hash types
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only rx_usec and tx_usec options for ethtool -C are settable as those
are the only settings that make sense to HW. Adds driver reporting of
intr coalescing timer value in usec units rather than HW units.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous driver was aligning ring sizes to 16 descs, but hardware actually
wants desc ring sizes to be aligned to 32 descs.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In set_multicast(), only push pkt filter changes down to firmware if
pkt filter actually changes.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During dev->open(), make sure we get at least one skb on the Rx ring.
Otherwise abort the interface load. Also, if we get skb allocation
failures in NAPI poll while trying to replenish the ring, try again
later so we don't end up starving out the Rx ring completely.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix dev->stop shutdown bug where driver was stopping xmit queue and then
disabling intrs. Fix is to disable intrs first and then stop the xmit
queue, otherwise an interrupt could cause the queue to be rewoken. Also,
no need to explicitly do queue servicing because queues are cleaned and
reset back to initial state at end of dev->stop. Servicing queues also
had the side-effect of also rewakening the xmit queue, which is not what
we want.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To unclutter probe() a little bit, put all device initialization code
in one spot and device deinit code in another spot. Also remove unused
rq->buf_index variable/func.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nic firmware can return zero for port MTU, so check for non-zero value
before checking for change in port MTU.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deprecate some old APIa; change arguments to stats dump all API; add new
interrupt assert API
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug fix: enable VLAN filtering
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provision for multiple Rx/Tx queues. Max of 8 WQs and 8 RQs. Max for
completion queue is 8+8=16 and max for interrupt resources is 8+8+2.
Add driver/firmware interface for setting up RSS secret key and indirection
table.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug fix: included MAC drops in rx_dropped netstat. Also track Rx trunctations
stat at the MAC
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some driver -> nic firmware calls weren't guarded with a spinlock, exposing
the call i/f to a race between two threads
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_alloc_skb rather than dev_alloc_skb
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enic WQ desc supports a maximum 16K buf size, so split any send fragments
larger than 16K into several descs.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A0 revision ASIC has an erratum on the RQ desc cache on chip where the
cache can become corrupted causing pkt buf writes to wrong locations. The s/w
workaround is to post a dummy RQ desc in the ring every 32 descs, causing a
flush of the cache. A0 parts are not production, but there are enough of
these parts in the wild in test setups to warrant including workaround. A1
revision ASIC parts fix erratum.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Followup of commits 9d21493b4beb8f918ba248032fefa393074a5e2b
and 08baf561083bc27a953aa087dd8a664bb2b88e8e
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tx_timeout reset path needs to re-init dev and re-apply nic cfg to
enable vlan stripping.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report all bad FCS errs as frames errs. This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns. No longer print a driver msg on bad FCS err.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return notify intr credits after notify intr from firmware. This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many drivers lost the ability to set ethernet address accidently
during the net_device_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix this sparse warning:
drivers/net/enic/vnic_dev.c:288:5: warning: symbol 'vnic_dev_capable' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarrify reading PBA has no side-effect (clearing).
Add missing GPL license text.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver/firmware compatibility check.
Update firmware notify cmd to honor notify area size.
Add new version of init cmd.
Add link_down_cnt to notify area to track link down count.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable ethtool support for get/set_flags so LRO can be turned on/off
by fwding drivers such as the bridge driver. LRO is not compatible
with fwding drivers.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
