aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2019-08-30net: stmmac: dwmac-rk: Don't fail if phy regulator is absentChen-Yu Tsai
The devicetree binding lists the phy phy as optional. As such, the driver should not bail out if it can't find a regulator. Instead it should just skip the remaining regulator related code and continue on normally. Skip the remainder of phy_power_on() if a regulator supply isn't available. This also gets rid of the bogus return code. Fixes: 2e12f536635f ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-30amd-xgbe: Fix error path in xgbe_mod_init()YueHaibing
In xgbe_mod_init(), we should do cleanup if some error occurs Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: efbaa828330a ("amd-xgbe: Add support to handle device renaming") Fixes: 47f164deab22 ("amd-xgbe: Add PCI device support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-28sky2: Disable MSI on yet another ASUS boards (P6Xxxx)Takashi Iwai
A similar workaround for the suspend/resume problem is needed for yet another ASUS machines, P6X models. Like the previous fix, the BIOS doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_* entries are used instead. Reported-and-tested-by: SteveM <swm@swm1.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-28nfp: flower: handle neighbour events on internal portsJohn Hurley
Recent code changes to NFP allowed the offload of neighbour entries to FW when the next hop device was an internal port. This allows for offload of tunnel encap when the end-point IP address is applied to such a port. Unfortunately, the neighbour event handler still rejects events that are not associated with a repr dev and so the firmware neighbour table may get out of sync for internal ports. Fix this by allowing internal port neighbour events to be correctly processed. Fixes: 45756dfedab5 ("nfp: flower: allow tunnels to output to internal port") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-28nfp: flower: prevent ingress block binds on internal portsJohn Hurley
Internal port TC offload is implemented through user-space applications (such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect block offload support in the NFP driver accepts both ingress qdisc binds and egress binds if the device is an internal port. However, clsact sends bind notification for both ingress and egress block binds which can lead to the driver registering multiple callbacks and receiving multiple notifications of new filters. Fix this by rejecting ingress block bind callbacks when the port is internal and only adding filter callbacks for egress binds. Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-28ibmvnic: Do not process reset during or after device removalThomas Falcon
Currently, the ibmvnic driver will not schedule device resets if the device is being removed, but does not check the device state before the reset is actually processed. This leads to a race where a reset is scheduled with a valid device state but is processed after the driver has been removed, resulting in an oops. Fix this by checking the device state before processing a queued reset event. Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-28macb: Update compatibility string for SiFive FU540-C000Yash Shah
Update the compatibility string for SiFive FU540-C000 as per the new string updated in the binding doc. Reference: https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/ Signed-off-by: Yash Shah <yash.shah@sifive.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com> Tested-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-24Merge tag 'mlx5-fixes-2019-08-22' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-08-22 This series introduces some fixes to mlx5 driver. 1) Form Moshe, two fixes for firmware health reporter 2) From Eran, two ktls fixes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-23Revert "r8169: remove not needed call to dma_sync_single_for_device"Heiner Kallweit
This reverts commit f072218cca5b076dd99f3dfa3aaafedfd0023a51. As reported by Aaro this patch causes network problems on MIPS Loongson platform. Therefore revert it. Fixes: f072218cca5b ("r8169: remove not needed call to dma_sync_single_for_device") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22qed: Add cleanup in qed_slowpath_start()Wenwen Wang
If qed_mcp_send_drv_version() fails, no cleanup is executed, leading to memory leaks. To fix this issue, introduce the label 'err4' to perform the cleanup work before returning the error. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22ocelot_ace: fix action of trapYangbo Lu
The trap action should be copying the frame to CPU and dropping it for forwarding, but current setting was just copying frame to CPU. Fixes: b596229448dd ("net: mscc: ocelot: Add support for tcam") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Allan W. Nielsen <allan.nielsen@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22net/mlx5e: Remove ethernet segment from dump WQEEran Ben Elisha
Dump WQE shall not include Ethernet segment. Define mlx5e_dump_wqe to be used for "Dump WQEs" instead of sharing it with the general mlx5e_tx_wqe layout. Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-22net/mlx5e: Add num bytes metadata to WQE infoEran Ben Elisha
For TLS WQEs, metadata info did not include num_bytes. Due to this issue, tx_tls_dump_bytes counter did not increment. Modify tx_fill_wi() to fill num bytes. When it is called for non-traffic WQE, zero is expected. Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-22net/mlx5: Fix delay in fw fatal report handling due to fw reportMoshe Shemesh
When fw fatal error occurs, poll health() first detects and reports on a fw error. Afterwards, it detects and reports on the fw fatal error itself. That can cause a long delay in fw fatal error handling which waits in a queue for the fw error handling to be finished. The fw error handle will try asking for fw core dump command while fw in fatal state may not respond and driver will wait for command timeout. Changing the flow to detect and handle first fw fatal errors and only if no fatal error detected look for a fw error to handle. Fixes: d1bf0e2cc4a6 ("net/mlx5: Report devlink health on FW issues") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-22net/mlx5: Fix crdump chunks printMoshe Shemesh
Crdump repeats itself every chunk of 256bytes. That is due to bug of missing progressing offset while copying the data from buffer to devlink_fmsg. Fixes: 9b1f29823605 ("net/mlx5: Add support for FW fatal reporter dump") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-21gve: Copy and paste bug in gve_get_stats()Dan Carpenter
There is a copy and paste error so we have "rx" where "tx" was intended in the priv->tx[] array. Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Catherine Sullivan <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-21net: cpsw: fix NULL pointer exception in the probe error pathAntoine Tenart
In certain cases when the probe function fails the error path calls cpsw_remove_dt() before calling platform_set_drvdata(). This is an issue as cpsw_remove_dt() uses platform_get_drvdata() to retrieve the cpsw_common data and leds to a NULL pointer exception. This patches fixes it by calling platform_set_drvdata() earlier in the probe. Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization") Reported-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-19nfp: flower: verify that block cb is not busy before bindingVlad Buslov
When processing FLOW_BLOCK_BIND command on indirect block, check that flow block cb is not busy. Fixes: 0d4fd02e7199 ("net: flow_offload: add flow_block_cb_is_busy() and use it") Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18ravb: Fix use-after-free ravb_tstamp_skbTho Vu
When a Tx timestamp is requested, a pointer to the skb is stored in the ravb_tstamp_skb struct. This was done without an skb_get. There exists the possibility that the skb could be freed by ravb_tx_free (when ravb_tx_free is called from ravb_start_xmit) before the timestamp was processed, leading to a use-after-free bug. Use skb_get when filling a ravb_tstamp_skb struct, and add appropriate frees/consumes when a ravb_tstamp_skb struct is freed. Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Tho Vu <tho.vu.wh@rvc.renesas.com> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18net: sched: use major priority number as hardware priorityPablo Neira Ayuso
tc transparently maps the software priority number to hardware. Update it to pass the major priority which is what most drivers expect. Update drivers too so they do not need to lshift the priority field of the flow_cls_common_offload object. The stmmac driver is an exception, since this code assumes the tc software priority is fine, therefore, lshift it just to be conservative. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18net: cavium: fix driver nameStephen Hemminger
The driver name gets exposed in sysfs under /sys/bus/pci/drivers so it should look like other devices. Change it to be common format (instead of "Cavium PTP"). This is a trivial fix that was observed by accident because Debian kernels were building this driver into kernel (bug). Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18ibmvnic: Unmap DMA address of TX descriptor buffers after useThomas Falcon
There's no need to wait until a completion is received to unmap TX descriptor buffers that have been passed to the hypervisor. Instead unmap it when the hypervisor call has completed. This patch avoids the possibility that a buffer will not be unmapped because a TX completion is lost or mishandled. Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Tested-by: Devesh K. Singh <devesh_singh@in.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Fix to include flow direction in L2 keySomnath Kotur
FW expects the driver to provide unique flow reference handles for Tx or Rx flows. When a Tx flow and an Rx flow end up sharing a reference handle, flow offload does not seem to work. This could happen in the case of 2 flows having their L2 fields wildcarded but in different direction. Fix to incorporate the flow direction as part of the L2 key v2: Move the dir field to the end of the bnxt_tc_l2_key struct to fix the warning reported by kbuild test robot <lkp@intel.com>. There is existing code that initializes the structure using nested initializer and will warn with the new u8 field added to the beginning. The structure also packs nicer when this new u8 is added to the end of the structure [MChan]. Fixes: abd43a13525d ("bnxt_en: Support for 64-bit flow handle.") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Use correct src_fid to determine direction of the flowVenkat Duvvuru
Direction of the flow is determined using src_fid. For an RX flow, src_fid is PF's fid and for TX flow, src_fid is VF's fid. Direction of the flow must be specified, when getting statistics for that flow. Currently, for DECAP flow, direction is determined incorrectly, i.e., direction is initialized as TX for DECAP flow, instead of RX. Because of which, stats are not reported for this DECAP flow, though it is offloaded and there is traffic for that flow, resulting in flow age out. This patch fixes the problem by determining the DECAP flow's direction using correct fid. Set the flow direction in all cases for consistency even if 64-bit flow handle is not used. Fixes: abd43a13525d ("bnxt_en: Support for 64-bit flow handle.") Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Suppress HWRM errors for HWRM_NVM_GET_VARIABLE commandVasundhara Volam
For newly added NVM parameters, older firmware may not have the support. Suppress the error message to avoid the unncessary error message which is triggered when devlink calls the driver during initialization. Fixes: 782a624d00fa ("bnxt_en: Add bnxt_en initial params table and register it.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd failsVasundhara Volam
If FW returns FRAG_ERR in response error code, driver is resending the command only when HWRM command returns success. Fix the code to resend NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns FRAG_ERR in its response error code. Fixes: cb4d1d626145 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Improve RX doorbell sequence.Michael Chan
When both RX buffers and RX aggregation buffers have to be replenished at the end of NAPI, post the RX aggregation buffers first before RX buffers. Otherwise, we may run into a situation where there are only RX buffers without RX aggregation buffers for a split second. This will cause the hardware to abort the RX packet and report buffer errors, which will cause unnecessary cleanup by the driver. Ringing the Aggregation ring doorbell first before the RX ring doorbell will prevent some of these buffer errors. Use the same sequence during ring initialization as well. Fixes: 697197e5a173 ("bnxt_en: Re-structure doorbells.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnxt_en: Fix VNIC clearing logic for 57500 chips.Michael Chan
During device shutdown, the VNIC clearing sequence needs to be modified to free the VNIC first before freeing the RSS contexts. The current code is doing the reverse and we can get mis-directed RX completions to CP ring ID 0 when the RSS contexts are freed and zeroed. The clearing of RSS contexts is not required with the new sequence. Refactor the VNIC clearing logic into a new function bnxt_clear_vnic() and do the chip specific VNIC clearing sequence. Fixes: 7b3af4f75b81 ("bnxt_en: Add RSS support for 57500 chips.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-18bnx2x: Fix VF's VLAN reconfiguration in reload.Manish Chopra
Commit 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence."), introduced a regression in driver that as a part of VF's reload flow, VLANs created on the VF doesn't get re-configured in hardware as vlan metadata/info was not getting cleared for the VFs which causes vlan PING to stop. This patch clears the vlan metadata/info so that VLANs gets re-configured back in the hardware in VF's reload flow and PING/traffic continues for VLANs created over the VFs. Fixes: 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com> Signed-off-by: Shahed Shaikh <shshaikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-15net: myri10ge: fix memory leaksWenwen Wang
In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices related structures. Later on, myri10ge_request_irq() is used to get an irq. However, if this process fails, the allocated slices related structures are not deallocated, leading to memory leaks. To fix this issue, revise the target label of the goto statement to 'abort_with_slices'. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-15liquidio: add cleanup in octeon_setup_iq()Wenwen Wang
If oct->fn_list.enable_io_queues() fails, no cleanup is executed, leading to memory/resource leaks. To fix this issue, invoke octeon_delete_instr_queue() before returning from the function. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-15net/mlx5e: Fix compatibility issue with ethtool flash deviceEran Ben Elisha
Cited patch deleted ethtool flash device support, as ethtool core can fallback into devlink flash callback. However, this is supported only if there is a devlink port registered over the corresponding netdevice. As mlx5e do not have devlink port support over native netdevice, it broke the ability to flash device via ethtool. This patch re-add the ethtool callback to avoid user functionality breakage when trying to flash device via ethtool. Fixes: 9c8bca2637b8 ("mlx5: Move firmware flash implementation to devlink") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-15net/mlx5e: Fix a race with XSKICOSQ in XSK wakeup flowMaxim Mikityanskiy
Add a missing spinlock around XSKICOSQ usage at the activation stage, because there is a race between a configuration change and the application calling sendto(). Fixes: db05815b36cb ("net/mlx5e: Add XSK zero-copy support") Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-14cxgb4: fix a memory leak bugWenwen Wang
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails, leading to a memory leak bug. To fix this issue, free t before returning the error. Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-13net/mlx4_en: fix a memory leak bugWenwen Wang
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS indirection. However, if mlx4_qp_alloc() fails, the allocated 'rss_map->indir_qp' is not deallocated, leading to a memory leak bug. To fix the above issue, add the 'qp_alloc_err' label to free 'rss_map->indir_qp'. Fixes: 4931c6ef04b4 ("net/mlx4_en: Optimized single ring steering") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-08-13ibmveth: Convert multicast list size for little-endian systemThomas Falcon
The ibm,mac-address-filters property defines the maximum number of addresses the hypervisor's multicast filter list can support. It is encoded as a big-endian integer in the OF device tree, but the virtual ethernet driver does not convert it for use by little-endian systems. As a result, the driver is not behaving as it should on affected systems when a large number of multicast addresses are assigned to the device. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-08-11net: tc35815: Explicitly check NET_IP_ALIGN is not zero in tc35815_rxNathan Chancellor
clang warns: drivers/net/ethernet/toshiba/tc35815.c:1507:30: warning: use of logical '&&' with constant operand [-Wconstant-logical-operand] if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN) ^ ~~~~~~~~~~~~ drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: use '&' for a bitwise operation if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN) ^~ & drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: remove constant to silence this warning if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN) ~^~~~~~~~~~~~~~~ 1 warning generated. Explicitly check that NET_IP_ALIGN is not zero, which matches how this is checked in other parts of the tree. Because NET_IP_ALIGN is a build time constant, this check will be constant folded away during optimization. Fixes: 82a9928db560 ("tc35815: Enable StripCRC feature") Link: https://github.com/ClangBuiltLinux/linux/issues/608 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-11mlxsw: spectrum_ptp: Keep unmatched entries in a linked listPetr Machata
To identify timestamps for matching with their packets, Spectrum-1 uses a five-tuple of (port, direction, domain number, message type, sequence ID). If there are several clients from the same domain behind a single port sending Delay_Req's, the only thing differentiating these packets, as far as Spectrum-1 is concerned, is the sequence ID. Should sequence IDs between individual clients be similar, conflicts may arise. That is not a problem to hardware, which will simply deliver timestamps on a first comes, first served basis. However the driver uses a simple hash table to store the unmatched pieces. When a new conflicting piece arrives, it pushes out the previously stored one, which if it is a packet, is delivered without timestamp. Later on as the corresponding timestamps arrive, the first one is mismatched to the second packet, and the second one is never matched and eventually is GCd. To correct this issue, instead of using a simple rhashtable, use rhltable to keep the unmatched entries. Previously, a found unmatched entry would always be removed from the hash table. That is not the case anymore--an incompatible entry is left in the hash table. Therefore removal from the hash table cannot be used to confirm the validity of the looked-up pointer, instead the lookup would simply need to be redone. Therefore move it inside the critical section. This simplifies a lot of the code. Fixes: 8748642751ed ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls") Reported-by: Alex Veber <alexve@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-11net: nps_enet: Fix function names in doc commentsJonathan Neuschäfer
Adjust the function names in two doc comments to match the corresponding functions. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-09Merge tag 'mlx5-fixes-2019-08-08' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-08-08 This series introduces some fixes to mlx5 driver. Highlights: 1) From Tariq, Critical mlx5 kTLS fixes to better align with hw specs. 2) From Aya, Fixes to mlx5 tx devlink health reporter. 3) From Maxim, aRFs parsing to use flow dissector to avoid relying on invalid skb fields. Please pull and let me know if there is any problem. For -stable v4.3 ('net/mlx5e: Only support tx/rx pause setting for port owner') For -stable v4.9 ('net/mlx5e: Use flow keys dissector to parse packets for ARFS') For -stable v5.1 ('net/mlx5e: Fix false negative indication on tx reporter CQE recovery') ('net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter') ('net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg off') Note: when merged with net-next this minor conflict will pop up: ++<<<<<<< (net-next) + if (is_eswitch_flow) { + flow->esw_attr->match_level = match_level; + flow->esw_attr->tunnel_match_level = tunnel_match_level; ++======= + if (flow->flags & MLX5E_TC_FLOW_ESWITCH) { + flow->esw_attr->inner_match_level = inner_match_level; + flow->esw_attr->outer_match_level = outer_match_level; ++>>>>>>> (net) To resolve, use hunks from net (2nd) and replace: if (flow->flags & MLX5E_TC_FLOW_ESWITCH) with if (is_eswitch_flow) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-09ixgbe: fix possible deadlock in ixgbe_service_task()Taehee Yoo
ixgbe_service_task() calls unregister_netdev() under rtnl_lock(). But unregister_netdev() internally calls rtnl_lock(). So deadlock would occur. Fixes: 59dd45d550c5 ("ixgbe: firmware recovery mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-08net: tundra: tsi108: use spin_lock_irqsave instead of spin_lock_irq in IRQ ↵Fuqian Huang
context As spin_unlock_irq will enable interrupts. Function tsi108_stat_carry is called from interrupt handler tsi108_irq. Interrupts are enabled in interrupt handler. Use spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in IRQ context to avoid this. Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-08net/mlx5e: Remove redundant check in CQE recovery flow of tx reporterAya Levin
Remove check of recovery bit, in the beginning of the CQE recovery function. This test is already performed right before the reporter is invoked, when CQE error is detected. Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: Fix error flow of CQE recovery on tx reporterAya Levin
CQE recovery function begins with test and set of recovery bit. Add an error flow which ensures clearing of this bit when leaving the recovery function, to allow further recoveries to take place. This allows removal of clearing recovery bit on sq activate. Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: Fix false negative indication on tx reporter CQE recoveryAya Levin
Remove wrong error return value when SQ is not in error state. CQE recovery on TX reporter queries the sq state. If the sq is not in error state, the sq is either in ready or reset state. Ready state is good state which doesn't require recovery and reset state is a temporal state which ends in ready state. With this patch, CQE recovery in this scenario is successful. Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: kTLS, Fix tisn field placementTariq Toukan
Shift the tisn field in the WQE control segment, per the HW specification. Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: kTLS, Fix tisn field nameTariq Toukan
Use the proper tisn field name from the union in struct mlx5_wqe_ctrl_seg. Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: kTLS, Fix progress params context WQE layoutTariq Toukan
The TLS progress params context WQE should not include an Eth segment, drop it. In addition, align the tls_progress_params layout with the HW specification document: - fix the tisn field name. - remove the valid bit. Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures") Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5: crypto, Fix wrong offset in encryption key commandTariq Toukan
Fix the 128b key offset in key encryption key creation command, per the HW specification. Fixes: 45d3b55dc665 ("net/mlx5: Add crypto library to support create/destroy encryption key") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-08-08net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg offMohamad Heib
Setting speed to 56GBASE is allowed only with auto-negotiation enabled. This patch prevent setting speed to 56GBASE when auto-negotiation disabled. Fixes: f62b8bb8f2d3 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality") Signed-off-by: Mohamad Heib <mohamadh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-21 21:04:13 +0000