| Age | Commit message (Collapse) | Author |
|---|
|
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The definition of array settings[] is quite lengthy meanwhile. Add a
macro to shrink the definition.
v2:
- Fix an indentation issue
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.
Fixes: 4950c2ba49cc ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The purpose of this change is to align the gxl and g12a driver
declaration.
Like on the g12a variant, remove genphy_aneg_done() from the driver
declaration as the net phy framework will default to it anyway.
Also, the gxl phy id should be an exact match as well, so let's change
this and use the macro provided.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The g12a SoC family uses the type of internal PHY that was used on the
gxl family. The quirks of gxl family, like the LPA register corruption,
appear to have been resolved on this new SoC generation.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the mdio mux and internal phy glue of the g12a SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # clk parts
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that phylib uses genphy_read_abilities() as fallback, we don't have
to set callback get_features any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meanwhile we have generic functions for reading the abilities of
Clause 22 / 45 PHY's. This allows to use them as fallback in case
callback get_features isn't set. Benefit is the reduction of
boilerplate code in PHY drivers.
v2:
- adjust the comment in phy_driver_register to match the code
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c69 ("net: phy: improve genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the 88x2110 PHY support was added, the suspend and resume callbacks
were forgotten. This patch adds them to the 88x2110 PHY callback
definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the suspend/resume callbacks for Marvell 10G PHYs. The
three PCS (base-t, base-r and 1000base-x) are set in low power (the PCS
are powered down) when the PHY isn't used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently mii_lpa_mod_linkmode_lpa_t() checks bit LPA_LPACK to detect
whether link partner supports autoneg. This doesn't work correctly at
least on Aquantia AQCS109 when it negotiates 1000Base-T2 mode.
The "link partner is autoneg-capable" bit as defined by clause 45 is
set however. Better let's switch in general to use the clause 45
standard for link partner autoneg detection.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AQR107 family has SGMII statistics counters. Let's expose them to
ethtool. To interpret the counters correctly one has to be aware that
rx on SGMII side is tx on ethernet side. The counters are populated
by the chip in 100Mbps/1Gbps mode only.
v2:
- add constant AQR107_SGMII_STAT_SZ
- add struct aqr107_priv to be prepared for more private data fields
- let aqr107_get_stat() return U64_MAX in case of an error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch improves few aspects of genphy_read_status():
- Don't initialize lpagb, it's not needed.
- Move initializing phydev->speed et al before the if clause.
- In auto-neg case, skip populating lp_advertising if we
don't have a link. This avoids quite some unnecessary
MDIO reads in case of phylib polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add suspend / resume callbacks for AQR107 family. Suspend powers down
the complete chip except MDIO and internal CPU.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The check for zero timeout is always true at the end of the proceeding
while loop; the only other exit path in the loop is if the unimac MDIO
is not busy. Remove the redundant zero timeout check and always
return -ETIMEDOUT on this timeout return path.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1000BaseT standard requires that a link is reported as down earliest
after 750ms. Several use case however require a much faster detecion
of a broken link. Fast Link Down supports this by intentionally
violating a the standard. This patch exposes the Fast Link Down
feature of 88E1540 and 88E6390. These PHY's can be found as internal
PHY's in several switches: 88E6352, 88E6240, 88E6176, 88E6172,
and 88E6390(X). Fast Link Down and EEE are mutually exclusive.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AQCS109 supports a proprietary 2-pair 1Gbps mode. The standard
registers don't allow to tell between 1000BaseT and 1000BaseT2.
Add reporting this proprietary mode based on a vendor register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add reporting firmware details. These details are available only once
the firmware has finished initializing the chip. This can take some
time and we need to poll for init completion.
v2:
- Propagate timeout in aqr107_wait_reset_complete(). Don't bail out
completely on timeout because chip may be functional even w/o
firmware image.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If both link partners are Aquantia PHY's then additional information is
exchanged as part of the auto-negotiation. Report remote capabilities
if link partner is Aquantia PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify aqr_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tristate prompt should have been replaced rather than defined a few
lines below, rebase mistake.
Fixes: 17cc9821766c ("net: phy: Move Omega PHY entry to Cygnus PHY driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.
v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cygnus and Omega are part of the same business unit and product line, it
makes sense to group PHY entries by products such that a platform can
select only the drivers that it needs. Bring all the functionality that
the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY
entry from bcm7xxx.c.
As an added bonus, we now have a proper mdio_device_id entry to permit
auto-loading.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on the auto-negotiated speed the PHY may change the interface
mode. Check for new mode and set phydev->interface accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: picked from bigger patch and reworked]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let config_init check for unsupported interface modes on AQR107/AQCS109.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: adjusted for AQR107/AQCS109 specifics]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
