| Age | Commit message (Collapse) | Author |
|---|
|
If r8196 received packets with invalid sctp/igmp(not tcp, udp) checksum, r8196 set skb->ip_summed
wit CHECKSUM_UNNECESSARY. This cause that upper protocol don't check checksum field.
I am not family with r8196 driver. I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(opts1 & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If it's right, I think we should not set ip_summed wit CHECKSUM_UNNECESSARY for my sctp packets
with invalid checksum.
If it's not right, please tell me.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As device_set_wakeup_enable can now sleep, move the call to outside
the critical section.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original patch helps under obscure conditions (no pun) but
some 8168 do not like it. The change needs to be tightened with
a specific 8168 version.
This reverts commit 801e147cde02f04b5c2f42764cd43a89fc7400a2
("r8169: Handle rxfifo errors on 8168 chips").
Regression at https://bugzilla.kernel.org/show_bug.cgi?id=20882
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Andreas Radke <a.radke@arcor.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If dma mapping fail we are dropping packages or fail to open device.
But exact reason of drop/fail stays unknow for a user, so print errors.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix switching device to low-speed mode after resume reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=502974
Reported-and-tested-by: Laurentiu Badea <bugzilla-redhat@wotevah.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we do not change rx buffer size any longer, we can
clean up rtl8169_change_mtu and in consequence rtl8169_down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only increase tx_{packets,dropped} statistics when transmit or drop
full skb, not just fragment.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check possible dma mapping errors and do clean up if it happens.
Fix overwrap bug in rtl8169_tx_clear on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb. There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances. However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using standard skb allocations in r8169 leads to order-3 allocations (if
PAGE_SIZE=4096), because NIC needs 16383 bytes, and skb overhead makes
this bigger than 16384 -> 32768 bytes per "skb"
Using kmalloc() permits to reduce memory requirements of one r8169 nic
by 4Mbytes. (256 frames * 16Kbytes). This is fine since a hardware bug
requires us to copy incoming frames, so we build real skb when doing
this copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/core/ethtool.c
|
|
Use DMA API as PCI equivalents will be deprecated. This change also
allow to allocate with GFP_KERNEL where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/qlcnic/qlcnic_init.c
net/ipv4/ip_output.c
|
|
The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Use napi_gro_receive() and vlan_gro_receive()
- Enable GRO by default
Tested on a RTL8111/8168 adapter
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While porting GRO to r8169, I found this driver has a bug in its rx
path.
All skbs given to network stack had their ip_summed set to
CHECKSUM_NONE, while hardware said they had correct TCP/UDP checksums.
The reason is driver sets skb->ip_summed on the original skb before the
copy eventually done by copybreak. The fresh skb gets the ip_summed =
CHECKSUM_NONE value, forcing network stack to recompute checksum, and
preventing my GRO patch to work.
Fix is to make the ip_summed setting after skb copy.
Note : rx_copybreak current value is 16383, so all frames are copied...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
|
|
This patch (as1388) changes the way the PCI core handles runtime PM
settings when probing or unbinding drivers. Now the core will make
sure the device is enabled for runtime PM, with a usage count >= 1,
when a driver is probed. It does the same when calling a driver's
remove method.
If the driver wants to use runtime PM, all it has to do is call
pm_runtime_pu_noidle() near the end of its probe routine (to cancel
the core's usage increment) and pm_runtime_get_noresume() near the
start of its remove routine (to restore the usage count). It does not
need to mess around with setting the runtime state to enabled,
disabled, active, or suspended.
The patch updates e1000e and r8169, the only PCI drivers that already
use the existing runtime PM interface.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/vhost/net.c
net/bridge/br_device.c
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36fd9c7c6d5218cdcd9948cee700b277d
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge error.
See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/sfc/net_driver.h
drivers/net/sfc/siena.c
|
|
Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
readl() returns a 32-bit integer on all platforms.
There is no need to cast its return value.
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/e100.c
drivers/net/e1000e/netdev.c
|
|
78f1cd02457252e1ffbc6caa44a17424a45286b8 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.
It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/via-velocity.c
drivers/net/wireless/iwlwifi/iwl-agn.c
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix formatting on r8169 printk
Brandon Philips noted that I had a spacing issue in my printk for the
last r8169 patch that made it quite ugly. Fix that up and add the PFX
macro to it as well so it looks like the other r8169 printks
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a reset is performed, rtl8169_rx_interrupt() is called from
process context instead of softirq context. Special care must be taken
to call appropriate network core services (netif_rx() instead of
netif_receive_skb()). VLAN handling also corrected.
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Diagnosed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Official patch to fix the r8169 frame length check error.
Based on this initial thread:
http://marc.info/?l=linux-netdev&m=126202972828626&w=1
This is the official patch to fix the frame length problems in the r8169
driver. As noted in the previous thread, while this patch incurs a performance
hit on the driver, its possible to improve performance dynamically by updating
the mtu and rx_copybreak values at runtime to return performance to what it was
for those NICS which are unaffected by the ideosyncracy (if there are any).
Summary:
A while back Eric submitted a patch for r8169 in which the proper
allocated frame size was written to RXMaxSize to prevent the NIC from dmaing too
much data. This was done in commit fdd7b4c3302c93f6833e338903ea77245eb510b4. A
long time prior to that however, Francois posted
126fa4b9ca5d9d7cb7d46f779ad3bd3631ca387c, which expiclitly disabled the MaxSize
setting due to the fact that the hardware behaved in odd ways when overlong
frames were received on NIC's supported by this driver. This was mentioned in a
security conference recently:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
It seems that if we can't enable frame size filtering, then, as Eric correctly
noticed, we can find ourselves DMA-ing too much data to a buffer, causing
corruption. As a result is seems that we are forced to allocate a frame which
is ready to handle a maximally sized receive.
This obviously has performance issues with it, so to mitigate that issue, this
patch does two things:
1) Raises the copybreak value to the frame allocation size, which should force
appropriately sized packets to get allocated on rx, rather than a full new 16k
buffer.
2) This patch only disables frame filtering initially (i.e., during the NIC
open), changing the MTU results in ring buffer allocation of a size in relation
to the new mtu (along with a warning indicating that this is dangerous).
Because of item (2), individuals who can't cope with the performance hit (or can
otherwise filter frames to prevent the bug), or who have hardware they are sure
is unaffected by this issue, can manually lower the copybreak and reset the mtu
such that performance is restored easily.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is quite similar to b39fe41f481d20c201012e4483e76c203802dda7
though said registers are not even documented as 64-bit registers
- as opposed to the initial TxDescStartAddress ones - but as single
bytes which must be combined into 32 bits at the MMIO read/write
level before being merged into a 64 bit logical entity.
Credits go to Ben Hutchings <ben@decadent.org.uk> for the MAR
registers (aka "multicast is broken for ages on ARM) and to
Timo Teräs <timo.teras@iki.fi> for the MAC registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 353176888386d9025062a12dcec08d49af10cf2c.
People are reporting problems due to this change and there
is no anticipation that the cause will be tracked down
any time soon.
We can try next time to selectively re-enable this based upon chip
type, or have a black list of some sort.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the PCI runtime power management framework to add basic PCI
runtime PM support to the r8169 driver. Namely, make the driver
suspend the device when the link is not present and set it up for
generating a wakeup event after the link has been detected again.
[This feature is disabled until the user space enables it with the
help of the /sys/devices/.../power/contol device attribute.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8169 needs certain writes to be visible to other CPUs or the NIC before
touching the hardware, but was using smp_wmb() which is only required to
order cacheable memory access. Switch to wmb() which is required to
order both cacheable and non-cacheable memory.
Noticed by Catalin Marinas and Paul Mackerras.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
removed some needless checks and also corrected bug in lp486e (dmi was passed
instead of dmi->dmi_addr)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently use of 64-bit DMA is disabled in r8169 unless the user passes the
use_dac module option. This is reasonable for conventional PCI devices where
broken chipsets may not handle dual-address-cycle transfers properly for
32-bit slots and so this may not be safe. However, PCI Express should not have
this problem and not using 64-bit DMA results in DMA transfers needlessly using
the IOMMU or SWIOTLB. Set the use_dac module parameter to a new default value of
-1 which results in 64-bit DMA being enabled by default for PCI Express devices
only.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the logic a bit, make the message logs a bit more consistent.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
