| Age | Commit message (Collapse) | Author |
|---|
|
Adds support for VF link status related changes.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF link initialization and offload features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove first zero for add, and use full attribute name in comments.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9fc, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9fc.
The issue commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use module_pci_driver() to get rid of some boilerplate code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These two statements were not indented correctly so it's sort of
confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We never set "slots" in this function.
Fixes: a9380b0f7be8 ("drivers: net: xgene: Add support for Jumbo frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-07
This series contains updates to i40e and i40evf only.
Filip modifies the i40e to log link speed change and when the link is
brought up and down.
Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code. Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.
Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+. Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions. Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it. Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters. Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.
Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.
Henry fixes the "ethtool -p" function for 1G BaseT PHYs.
Carolyn adds support for 25G devices for i40e and i40evf.
Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.
v2: dropped last patch from previous series, since changes are needed based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"),
the mtu range for dummy device becomes [68, 1500].
This patch extends it to [0, 65535].
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"),
mtu range is checked at dev_set_mtu().
This patch adds min_mtu for nlmon device and remove unnecessary
ndo_change_mtu() function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When free macvlan_port in macvlan_port_destroy, it is safe to free
directly because netdev_rx_handler_unregister could enforce one
grace period.
So it is unnecessary to use kfree_rcu for macvlan_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.
So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.
phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.
[ 13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[ 13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[ 13.742115] Hardware name: Axis ARTPEC-6 Platform
[ 13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[ 13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[ 13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[ 13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[ 13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[ 13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[ 13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[ 13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[ 13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[ 13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[ 13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[ 13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[ 13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b83 ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().
So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpts_register/unregister
There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.
Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.
Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.
1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success. After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.
2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.
3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device(). A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.
4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.
5. 1 stats context is reserved when the RDMA driver registers. MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.
6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.
v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver register function with firmware consists of passing version
information and registering for async events. To support the RDMA driver,
the async events that we need to register may change. Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible. However, the
user can still increase network rings to the max if he wants. The actual
RDMA resources won't be reserved until the RDMA driver registers.
v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened. So we cannot do
function reset in bnxt_open() which will clear all the resources.
The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one(). This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.
Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode(). bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX. The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By refactoring existing code into this new function. The new function
will be used in subsequent patches.
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to how we handled exiting VLAN mode, move the logic
in i40e_vsi_add_vlan into i40e_sync_vsi_filters. Extract this logic into
its own function for ease of understanding as it will become quite
complex.
The new function, i40e_correct_mac_vlan_filters() correctly updates all
filters for when we need to enter VLAN mode, exit VLAN mode, and also
enforces the PVID when assigned.
Call i40e_correct_mac_vlan_filters from i40e_sync_vsi_filters passing it
the number of active VLAN filters, and the two temporary lists.
Remove the function for updating VLAN=0 filters from i40e_vsi_add_vlan.
The end result is that the logic for entering and exiting VLAN mode is
in one location which has the most knowledge about all filters. This
ensures that we always correctly have the non-VLAN filters assigned to
VID=0 or VID=-1 regardless of how we ended up getting to this result.
Additionally this enforces the PVID at sync time so that we know for
certain that an assigned PVID results in only filters with that PVID
will be added to the firmware.
Change-ID: I895cee81e9c92d0a16baee38bd0ca51bbb14e372
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A future refactor of how the PF assigns a PVID to a VF will want to be
able to add and remove a block of filters by VLAN without worrying about
accidentally triggering the accounting for I40E_VLAN_ANY. Additionally
the PVID assignment would like to be able to batch several changes under
one use of the mac_filter_hash_lock.
Factor out the addition and deletion of a VLAN on all MACs into their
own function which i40e_vsi_(add|kill)_vlan can use. These new functions
expect the caller to take the hash lock, as well as perform any
necessary accounting for updating I40E_VLAN_ANY filters if we are now
operating under VLAN mode.
Change-ID: If79e5b60b770433275350a74b3f1880333a185d5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a subtle issue with the code for converting VID=-1 filters into VID=0
filters when adding a new VLAN. Previously the code deleted the VID=-1
filter, and then added a new VID=0 filter. In the rare case that the
addition fails due to -ENOMEM, we end up completely deleting the filter
which prevents recovery if memory pressure subsides. While it is not
strictly an issue because it is likely that memory issues would result
in many other problems, we shouldn't delete the filter until after the
addition succeeds.
Change-ID: Icba07ddd04ecc6a3b27c2e29f2c1c8673d266826
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current caller of i40e_update_filter_state incorrectly passes
aq_ret, an i40e_status variable, instead of the expected aq_err. This
happens to work because i40e_status is actually just a typedef integer,
and 0 is still the successful return. However i40e_update_filter_state
has special handling for ENOSPC which is currently being ignored.
Also notice that firmware does not update the per-filter response for
many types of errors, such as EINVAL. Thus, modify the filter setup so
that the firmware response memory is pre-set with I40E_AQC_MM_ERR_NO_RES.
This enables us to refactor i40e_update_filter_state, removing the need
to pass aq_err and avoiding a need for having 3 different flows for
checking the filter state.
The resulting code for i40e_update_filter_state is much simpler, only
a single loop and we always check each filter response value every time.
Since we pre-set the response value to match our expected error this
correctly works for all success and error flows.
Change-ID: Ie292c9511f34ee18c6ef40f955ad13e28b7aea7d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previous code refactors have accidentally caused issues with the
counting of active_filters. Avoid similar issues in the future by simply
re-counting the active filters every time after we handle add and delete
of all the filters. Additionally this allows us to simplify the check
for when we exit promiscuous mode since we can combine the check for
failed filters at the same time.
Additionally since we recount filters at the end we need to set
vsi->promisc_threshold as well.
The resulting code takes a bit longer since we do have to loop over
filters again. However, the result is more readable and less likely to
become incorrect due to failed accounting of filters in the future.
Finally, this ensures that it is not possible for vsi->active_filters to
ever underflow since we never decrement it.
Change-ID: Ib4f3a377e60eb1fa6c91ea86cc02238c08edd102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A product decision has been made to defeature detection of PTP frames
over L4 (UDP) on the XL710 MAC. Do not advertise support for L4
timestamping.
Change-ID: I41fbb0f84ebb27c43e23098c08156f2625c6ee06
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The service task lock was being set in the scheduling function, not the
actual service task. This would potentially leave the bit set for a long
time before the task actually ran. Furthermore, if the service task
takes too long, it calls the schedule function to reschedule itself -
which would fail to take the lock and do nothing.
Instead, set and clear the lock bit in the service task itself. In the
process, get rid of the i40e_service_event_complete() function, which is
really just two lines of code that can be put right in the service task
itself.
Change-ID: I83155e682b686121e2897f4429eb7d3f7c669168
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
