| Age | Commit message (Collapse) | Author |
|---|
|
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e05 ("r8169: remove work from irq handler.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot_vlant_wait_for_completion() function is very similar to the
ocelot_mact_wait_for_completion(). It seemed to have be copied but the
comment was not updated, so let's fix it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 713a98d90c5e ("virtio-net: serialize tx routine during reset")
introduces netif_tx_disable() after netif_device_detach() in order to
avoid use-after-free of tx queues. However, there are two issues.
1) Its operation is redundant with netif_device_detach() in case the
interface is running.
2) In case of the interface is not running before suspending and
resuming, the tx does not get resumed by netif_device_attach().
This results in losing network connectivity.
It is better to use netif_tx_lock_bh()/netif_tx_unlock_bh() instead for
serializing tx routine during reset. This also preserves the symmetry
of netif_device_detach() and netif_device_attach().
Fixes commit 713a98d90c5e ("virtio-net: serialize tx routine during reset")
Signed-off-by: Ake Koomsin <ake@igel.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the switch driver (e.g., mlxsw_spectrum) determines it needs to
flash a new firmware version it resets the ASIC after the flashing
process. The bus driver (e.g., mlxsw_pci) then registers itself again
with mlxsw_core which means (among other things) that the device
registers itself again with the hwmon subsystem again.
Since the device was registered with the hwmon subsystem using
devm_hwmon_device_register_with_groups(), then the old hwmon device
(registered before the flashing) was never unregistered and was
referencing stale data, resulting in a use-after free.
Fix by removing reliance on device managed APIs in mlxsw_hwmon_init().
Fixes: c86d62cc410c ("mlxsw: spectrum: Reset FW after flash")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to d49c88d7677b ("r8169: Enable MSI-X on RTL8106e") after
e9d0ba506ea8 ("PCI: Reprogram bridge prefetch registers on resume")
we can safely assume that this also fixes the root cause of
the issue worked around by 7c53a722459c ("r8169: don't use MSI-X on
RTL8168g"). So let's revert it.
Fixes: 7c53a722459c ("r8169: don't use MSI-X on RTL8168g")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang currently warns:
drivers/net/ethernet/qlogic/qla3xxx.c:384:24: warning: signed shift
result (0xF00000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
~~~~~~~~~~~~~~ ^ ~~
1 warning generated.
The warning is certainly accurate since ISP_NVRAM_MASK is defined as
(0x000F << 16) which is then shifted by 16, resulting in 64424509440,
well above UINT_MAX.
Given that this is the only location in this driver where ISP_NVRAM_MASK
is shifted again, it seems likely that ISP_NVRAM_MASK was originally
defined without a shift and during the move of the shift to the
definition, this statement wasn't properly removed (since ISP_NVRAM_MASK
is used in the statenent right above this). Only the maintainers can
confirm this since this statment has been here since the driver was
first added to the kernel.
Link: https://github.com/ClangBuiltLinux/linux/issues/127
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We shouldn't abuse exceptions: if the destination MTU is already higher
than what we're transmitting, no exception should be created.
Fixes: 52a589d51f10 ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff4490 ("vxlan: update skb dst pmtu on tx path")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f15ca723c1eb ("net: don't call update_pmtu unconditionally") avoids
that we try updating PMTU for a non-existent destination, but didn't clean
up cases where the check was already explicit. Drop those redundant checks.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously when populating the set ipv6 address action, we incorrectly
made use of pedit's key index to determine which 32bit word should be
set. We now calculate which word has been selected based on the offset
provided by the pedit action.
Fixes: 354b82bb320e ("nfp: add set ipv6 source and destination address")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we only allowed a single header key per pedit action to
change the header. This used to result in the last header key in the
pedit action to overwrite previous headers. We now keep track of them
and allow multiple header keys per pedit action.
Fixes: c0b1bd9a8b8a ("nfp: add set ipv4 header action flower offload")
Fixes: 354b82bb320e ("nfp: add set ipv6 source and destination address")
Fixes: f8b7b0a6b113 ("nfp: add set tcp and udp header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we did not correctly change headers when using multiple
pedit actions with partial masks. We now take this into account and
no longer just commit the last pedit action.
Fixes: c0b1bd9a8b8a ("nfp: add set ipv4 header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit db65f35f50e0 ("net: fec: add support of ethtool get_regs") introduce
ethool "--register-dump" interface to dump all FEC registers.
But not all silicon implementations of the Freescale FEC hardware module
have the FRBR (FIFO Receive Bound Register) and FRSR (FIFO Receive Start
Register) register, so we should not be trying to dump them on those that
don't.
To fix it we create a quirk flag, FEC_QUIRK_HAS_RFREG, and check it before
dump those RX FIFO registers.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in DP_INFO message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d9c ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-10
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169
Kernel modules: r8169
We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes. That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.
However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes. It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.
After apply the patch, the ethernet adapter works fine before suspend
and after resume. So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.
This patch reverts commit 7bb05b85bc2d1a1b647b91424b2ed4a18e6ecd81
"r8169: don't use MSI-X on RTL8106e".
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85bc2d ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Ulf writes:
"MMC core:
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card"
* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
libertas: call into generic suspend code before turning off power
mmc: block: avoid multiblock reads for the last sector in SPI mode
|
|
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
|
|
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.
Remove sfp_mutex, it has no purpose.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported that since
commit 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 63ae7949e94a ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During boot, mlx4_core sets the driverinit configuration parameters and
updates the devlink module on the initial values calling
devlink_param_driverinit_value_set().
If devlink_param_driverinit_value_set() returns an error mlx4_core
reports kernel module warning.
This caused false alarm during boot in case kernel was compiled with
CONFIG_NET_DEVLINK off.
Fix by removing warning reported in case
devlink_param_driverinit_value_set() fails.
This actually makes the function mlx4_devlink_set_init_value()
redundant to using directly devlink_param_driverinit_value_set() and so
removed.
It fixes the following kernel trace:
mlx4_core 0000:00:06.0: devlink set parameter 0 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 1 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 4 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 5 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 3 value failed (err = -95)
Fixes: bd1b51dc66df ("mlx4: Add mlx4 initial parameters table and register it")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Kees writes:
"Fix open-coded multiplication arguments to allocators
- Fixes several new open-coded multiplications added in the 4.19
merge window."
* tag 'alloc-args-v4.19-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Replace more open-coded allocation size multiplications
|
|
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5e netdevice used to calculate fragment edges by a call to
mlx5_wq_cyc_get_frag_size(). This calculation did not give the correct
indication for queues smaller than a PAGE_SIZE, (broken by default on
PowerPC, where PAGE_SIZE == 64KB). Here it is replaced by the correct new
calls/API.
Since (TX/RX) Work Queues buffers are fragmented, here we introduce
changes to the API in core driver, so that it gets a stride index and
returns the index of last stride on same fragment, and an additional
wrapping function that returns the number of physically contiguous
strides that can be written contiguously to the work queue.
This obsoletes the following API functions, and their buggy
usage in EN driver:
* mlx5_wq_cyc_get_frag_size()
* mlx5_wq_cyc_ctr2fragix()
The new API improves modularity and hides the details of such
calculation for mlx5e netdevice and mlx5_ib rdma drivers.
New calculation is also more efficient, and improves performance
as follows:
Packet rate test: pktgen, UDP / IPv4, 64byte, single ring, 8K ring size.
Before: 16,477,619 pps
After: 17,085,793 pps
3.7% improvement
Fixes: 3a2f70331226 ("net/mlx5: Use order-0 allocations for all WQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The HW spec defines only bits 24-26 of pftype_wq as the page fault type,
use the required mask to ensure that.
Fixes: d9aaed838765 ("{net,IB}/mlx5: Refactor page fault handling")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allocated memory for context should be freed once
finished working with it.
Fixes: d6c4f0298cec ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When powering down a SDIO connected card during suspend, make sure to call
into the generic lbs_suspend() function before pulling the plug. This will
make sure the card is successfully deregistered from the system to avoid
communication to the card starving out.
Fixes: 7444a8092906 ("libertas: fix suspend and resume for SDIO connected cards")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Eliminate potential auto casting compilation error.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb2d ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71b6 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b41c ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In yam_ioctl(), the concrete ioctl command is firstly copied from the
user-space buffer 'ifr->ifr_data' to 'ioctl_cmd' and checked through the
following switch statement. If the command is not as expected, an error
code EINVAL is returned. In the following execution the buffer
'ifr->ifr_data' is copied again in the cases of the switch statement to
specific data structures according to what kind of ioctl command is
requested. However, after the second copy, no re-check is enforced on the
newly-copied command. Given that the buffer 'ifr->ifr_data' is in the user
space, a malicious user can race to change the command between the two
copies. This way, the attacker can inject inconsistent data and cause
undefined behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae83959b6 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473ec9 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0ff ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
team's ndo_add_slave() acquires 'team->lock' and later tries to open the
newly enslaved device via dev_open(). This emits a 'NETDEV_UP' event
that causes the VLAN driver to add VLAN 0 on the team device. team's
ndo_vlan_rx_add_vid() will also try to acquire 'team->lock' and
deadlock.
Fix this by checking early at the enslavement function that a team
device is not being enslaved to itself.
A similar check was added to the bond driver in commit 09a89c219baf
("bonding: disallow enslaving a bond to itself").
WARNING: possible recursive locking detected
4.18.0-rc7+ #176 Not tainted
--------------------------------------------
syz-executor4/6391 is trying to acquire lock:
(____ptrval____) (&team->lock){+.+.}, at: team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
but task is already holding lock:
(____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&team->lock);
lock(&team->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by syz-executor4/6391:
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4662
#1: (____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
stack backtrace:
CPU: 1 PID: 6391 Comm: syz-executor4 Not tainted 4.18.0-rc7+ #176
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
check_deadlock kernel/locking/lockdep.c:1809 [inline]
validate_chain kernel/locking/lockdep.c:2405 [inline]
__lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
__mutex_lock_common kernel/locking/mutex.c:757 [inline]
__mutex_lock+0x176/0x1820 kernel/locking/mutex.c:894
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:909
team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
vlan_add_rx_filter_info+0x14a/0x1d0 net/8021q/vlan_core.c:210
__vlan_vid_add net/8021q/vlan_core.c:278 [inline]
vlan_vid_add+0x63e/0x9d0 net/8021q/vlan_core.c:308
vlan_device_event.cold.12+0x2a/0x2f net/8021q/vlan.c:381
notifier_call_chain+0x180/0x390 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
call_netdevice_notifiers net/core/dev.c:1753 [inline]
dev_open+0x173/0x1b0 net/core/dev.c:1433
team_port_add drivers/net/team/team.c:1219 [inline]
team_add_slave+0xa8b/0x1c30 drivers/net/team/team.c:1948
do_set_master+0x1c9/0x220 net/core/rtnetlink.c:2248
do_setlink+0xba4/0x3e10 net/core/rtnetlink.c:2382
rtnl_setlink+0x2a9/0x400 net/core/rtnetlink.c:2636
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4665
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2455
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4683
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfd0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:642 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:652
___sys_sendmsg+0x7fd/0x930 net/socket.c:2126
__sys_sendmsg+0x11d/0x290 net/socket.c:2164
__do_sys_sendmsg net/socket.c:2173 [inline]
__se_sys_sendmsg net/socket.c:2171 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2171
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x456b29
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9706bf8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f9706bf96d4 RCX: 0000000000456b29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d3548 R14: 00000000004c8227 R15: 0000000000000000
Fixes: 87002b03baab ("net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+bd051aba086537515cdb@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 602b74eda813 ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.
However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Artem Shvorin <art@qrator.net>
Tested-by: Artem Shvorin <art@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a hardware issue in Spectrum-2, the field event_type of the event
queue element (EQE) has become reserved. It was used to distinguish between
command interface completion events and completion events.
Use queue number to determine event type, as command interface completion
events are always received on EQ0 and mlxsw driver maps completion events
to EQ1.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David writes:
"Networking fixes:
1) Prefix length validation in xfrm layer, from Steffen Klassert.
2) TX status reporting fix in mac80211, from Andrei Otcheretianski.
3) Fix hangs due to TX_DROP in mac80211, from Bob Copeland.
4) Fix DMA error regression in b43, from Larry Finger.
5) Add input validation to xenvif_set_hash_mapping(), from Jan Beulich.
6) SMMU unmapping fix in hns driver, from Yunsheng Lin.
7) Bluetooh crash in unpairing on SMP, from Matias Karhumaa.
8) WoL handling fixes in the phy layer, from Heiner Kallweit.
9) Fix deadlock in bonding, from Mahesh Bandewar.
10) Fill ttl inherit infor in vxlan driver, from Hangbin Liu.
11) Fix TX timeouts during netpoll, from Michael Chan.
12) RXRPC layer fixes from David Howells.
13) Another batch of ndo_poll_controller() removals to deal with
excessive resource consumption during load. From Eric Dumazet.
14) Fix a specific TIPC failure secnario, from LUU Duc Canh.
15) Really disable clocks in r8169 during suspend so that low
power states can actually be reached.
16) Fix SYN backlog lockdep issue in tcp and dccp, from Eric Dumazet.
17) Fix RCU locking in netpoll SKB send, which shows up in bonding,
from Dave Jones.
18) Fix TX stalls in r8169, from Heiner Kallweit.
19) Fix locksup in nfp due to control message storms, from Jakub
Kicinski.
20) Various rmnet bug fixes from Subash Abhinov Kasiviswanathan and
Sean Tranchetti.
21) Fix use after free in ip_cmsg_recv_dstaddr(), from Eric Dumazet."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (122 commits)
ixgbe: check return value of napi_complete_done()
sctp: fix fall-through annotation
r8169: always autoneg on resume
ipv4: fix use-after-free in ip_cmsg_recv_dstaddr()
net: qualcomm: rmnet: Fix incorrect allocation flag in receive path
net: qualcomm: rmnet: Fix incorrect allocation flag in transmit
net: qualcomm: rmnet: Skip processing loopback packets
net: systemport: Fix wake-up interrupt race during resume
rtnl: limit IFLA_NUM_TX_QUEUES and IFLA_NUM_RX_QUEUES to 4096
bonding: fix warning message
inet: make sure to grab rcu_read_lock before using ireq->ireq_opt
nfp: avoid soft lockups under control message storm
declance: Fix continuation with the adapter identification message
net: fec: fix rare tx timeout
r8169: fix network stalls due to missing bit TXCFG_AUTO_FIFO
tun: napi flags belong to tfile
tun: initialize napi_mutex unconditionally
tun: remove unused parameters
bond: take rcu lock in netpoll_send_skb_on_dev
rtnetlink: Fail dump if target netnsid is invalid
...
|
