| Age | Commit message (Collapse) | Author |
|---|
|
MSI is defined to be 32-bit write. The 5706 does 64-bit MSI writes
with byte enables disabled on the unused 32-bit word. This is legal
but causes problems on the AMD 8132 which will eventually stop
responding after a while.
Without this patch, the MSI test done by the driver during open will
pass, but MSI will eventually stop working after a few MSIs are
written by the device.
AMD believes this incompatibility is unique to the 5706, and
prefers to locally disable MSI rather than globally disabling it
using pci_msi_quirk.
Update version to 1.4.45.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For len equal to 4, we never call sppp_lcp_conf_parse_options(),
therefore rmagic does not get initialized.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Introduce the disable_irq_nosync_lockdep_irqsave() and
enable_irq_lockdep_irqrestore() APIs. These are needed for NE2000; basically
NE2000 calls disable_irq and enable_irq as locking against the IRQ handler,
but both in cases where interrupts are on and off. This means that lockdep
needs to track the old state of the virtual irq flags on disable_irq, and
restore these at enable_irq time.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
As suggested by Muli Ben-Yehuda this function is moved to generic code as
may be useful for all archs.
[akpm@osdl.org: fix]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add smc91x support for TI OMAP2420 H4 EVM board.
Cc: <nico@cam.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
FIFOCTL_RXERR and FIFOCTL_TXERR are undocumented bits, according to the
Sigmatel datasheet. We should thus not take any assumption on their values
and semantics.
Problem spotted by andrzej zaborowski <balrogg@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch detects the smsc-ircc chipset on the nx1000
(including nx7000 and nx7010) and the nx5000 HP/Compaq laptop series.
Patch from "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to NatSemi datasheet, the configuration base address for the PC8738x
family is 0x2e or 0x164. 0x0 doesn't appear in any datasheet.
Patch from Lamarque Vieira Souza <lamarque@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The loopback device status structure is a singleton and doesn't
need to be allocated. Add ethtool_ops hooks to show checksum always on,
and make ethtool_ops const.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the inclusion of the stir421x code, we now need to select FW_LOADER
whenever we try to build the irda-usb code.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPPoE must advertise the underlying device's MTU via the ppp channel
descriptor structure, as multilink functionality depends on it.
Signed-off-by: Michal Ostrowski <mostrows@earthlink.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update version to 3.66.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 5709 10/100 PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the new 5709 device. This is a new 10/100 Mbps chip.
The mailbox access and firmware interface are quite different from
all other tg3 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the firmware polling logic into a separate function. This makes
the code cleaner.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IDs to support 5722 and 5756.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHY related fixes:
1. Fix Serdes WoL.
2. Fix loopback test on 10/100 only devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change to a different ASF heartbeat message code to improve
reliability.
There were some reports of unintended resets on real time kernels
where the timer may be slow and cause the heartbeat to be late.
Netpoll will also have the same problem because the timer irq will
be unavailable.
Using the new heartbeat code, the ASF firmware will also check the
ring condition before resetting the chip when the heartbeat is
expiring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve 5704S autoneg logic by using a serdes_counter field to keep
track of the transient states. This eliminates a 200 msec busy
loop in the code. Autoneg will take its course without the driver
busy waiting for it to finish.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Net devices should depend on NETDEVICES, so revert part of
Paolo's previous patch.
See http://marc.theaimsgroup.com/?l=linux-kernel&m=115566326218740&w=2
for history.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix memory leak.
Coverity id# 653
patch location:
http://www.kernel.org/git/?p=linux/kernel/git/bcollins/ubuntu-dapper.git;a=commitdiff;h=a1f34cb68b16807ed9d5ebb0f6a6ec5ff8a5fc78
Signed-off-by: Chuck Short <zulcss@gmail.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (130 commits)
[ARM] 3856/1: Add clocksource for Intel IXP4xx platforms
[ARM] 3855/1: Add generic time support
[ARM] 3873/1: S3C24XX: Add irq_chip names
[ARM] 3872/1: S3C24XX: Apply consistant tabbing to irq_chips
[ARM] 3871/1: S3C24XX: Fix ordering of EINT4..23
[ARM] nommu: confirms the CR_V bit in nommu mode
[ARM] nommu: abort handler fixup for !CPU_CP15_MMU cores.
[ARM] 3870/1: AT91: Start removing static memory mappings
[ARM] 3869/1: AT91: NAND support for DK and KB9202 boards
[ARM] 3868/1: AT91 hardware header update
[ARM] 3867/1: AT91 GPIO update
[ARM] 3866/1: AT91 clock update
[ARM] 3865/1: AT91RM9200 header updates
[ARM] 3862/2: S3C2410 - add basic power management support for AML M5900 series
[ARM] kthread: switch arch/arm/kernel/apm.c
[ARM] Off-by-one in arch/arm/common/icst*
[ARM] 3864/1: Refactore sharpsl_pm
[ARM] 3863/1: Add Locomo SPI Device
[ARM] 3847/2: Convert LOMOMO to use struct device for GPIOs
[ARM] Use CPU_CACHE_* where possible in asm/cacheflush.h
...
|
|
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
|
|
I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
In file included from drivers/net/wan/pc300_tty.c:59:
drivers/net/wan/pc300.h:335: error: field 'pppdev' has incomplete type
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (108 commits)
sh: Fix occasional flush_cache_4096() stack corruption.
sh: Calculate shm alignment at runtime.
sh: dma-mapping compile fixes.
sh: Initial vsyscall page support.
sh: Clean up PAGE_SIZE definition for assembly use.
sh: Selective flush_cache_mm() flushing.
sh: More intelligent entry_mask/way_size calculation.
sh: Support for L2 cache on newer SH-4A CPUs.
sh: Update kexec support for API changes.
sh: Optimized readsl()/writesl() support.
sh: Report movli.l/movco.l capabilities.
sh: CPU flags in AT_HWCAP in ELF auxvt.
sh: Add support for 4K stacks.
sh: Enable /proc/kcore support.
sh: stack debugging support.
sh: select CONFIG_EMBEDDED.
sh: machvec rework.
sh: Solution Engine SH7343 board support.
sh: SH7710VoIPGW board support.
sh: Enable verbose BUG() support.
...
|
|
Add modalias attribute support for the almost forgotten now EISA bus and
(at least some) EISA-aware modules.
The modalias entry looks like (for an 3c509 NIC):
eisa:sTCM5093
and the in-module alias like:
eisa:sTCM5093*
The patch moves struct eisa_device_id declaration from include/linux/eisa.h
to include/linux/mod_devicetable.h (so that the former now #includes the
latter), adds proper MODULE_DEVICE_TABLE(eisa, ...) statements for all
drivers with EISA IDs I found (some drivers already have that DEVICE_TABLE
declared), and adds recognision of __mod_eisa_device_table to
scripts/mod/file2alias.c so that proper modules.alias will be generated.
There's no support for /lib/modules/$kver/modules.eisamap, as it's not used
by any existing tools, and because with in-kernel modalias mechanism those
maps are obsolete anyway.
The rationale for this patch is:
a) to make EISA bus to act as other busses with modalias
support, to unify driver loading
b) to foget about EISA finally - with this patch, kernel
(who still supports EISA) will be the only one who knows
how to choose the necessary drivers for this bus ;)
[akpm@osdl.org: fix the kbuild bit]
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-the-net-bits-by: Jeff Garzik <jeff@garzik.org>
Acked-the-tulip-bit-by: Valerie Henson <val_henson@linux.intel.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This updates the various boards for some of the recent I/O routine
updates.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch removes accesses to the HDLC-internal data structures
from pc300 driver, thus enabling it to compile but breaking part
of its functionality.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch enables building of individual WAN protocol support
routines (parts of generic HDLC) as separate modules.
All protocol-private definitions are moved from hdlc.h file
to protocol drivers. User-space interface and interface
between generic HDLC and underlying low-level HDLC drivers
are unchanged.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into tmp
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
le32_to_cpu() on 64bit values
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
At enslavement time, the primary slave might not be activated if
there is already an active slave and the new slave is the primary.
Replaced complicated logic with a call to bond_select_active_slave(),
which does the right thing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6378
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixed handling of 802.3ad LACPDUs. Do not byte swap data in
place in the packet. Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.
Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add priv_flag to specifically identify bonding-involved devices. Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER). Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.
Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The bonding driver fails to adjust its hard_header_len when enslaving
interfaces. Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics. GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming. Enslaving such a device and then transmitting over
it causes a kernel panic.
Patch modified from submitter's original, but submitter agreed with this
patch in private email.
Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove unneeded test for NULL. Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
