| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.13 pull request
This is the NFC pull requesy for 4.13. We have:
- A conversion to unified device and GPIO APIs for the
fdp, pn544, and st{21,-nci} drivers.
- A fix for NFC device IDs allocation.
- A fix for the nfcmrvl driver firmware download mechanism.
- A trf7970a DT and GPIO cleanup and clock setting fix.
- A few fixes for potential overflows in the digital and LLCP code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In prior commits the selected clock frequency does not propagate
correctly to what is written to the TRF7970A_MODULATOR_SYS_CLK_CTRL
register.
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NULL checks at line 457: if (!link0 || !link1) {, implies that both
pointers link0 and link1 might be NULL.
Function nfcsim_link_free() dereference pointers link0 and link1.
Add NULL checks before calling nfcsim_link_free() to avoid a
potential NULL pointer dereference.
Addresses-Coverity-ID: 1364857
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This reverts commit ab714817d7e891608d31f6996b1e4c43cf2bf342.
The original commit was designed to handle a bug in the trf7970a NFC
controller where an extra byte was returned in Read Multiple Blocks (RMB)
command responses. However, it has become less clear whether it is a bug
in the trf7970a or in the tag. In addition, it was assumed that the extra
byte was always returned but it turns out that is not always the case. The
result is that a byte of good data is trimmed off when the extra byte is
not present ultimately causing the neard deamon to fail the read.
Since the trf7970a driver does not have the context to know when to trim
the byte or not, remove the code from the trf7970a driver all together
(and move it up to the neard daemon). This has the added benefit of
simplifying the kernel driver and putting the extra complexity into
userspace.
CC: Rob Herring <robh@kernel.org>
CC: devicetree@vger.kernel.org
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The "or" condition (clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_13MHZ_CLOCK_FREQUE) will always be true because
clk_freq cannot be equal to two different values at the same time. Use
the && operator instead of || to fix this.
Detected by CoverityScan, CID#1430468 ("Constant expression result")
Fixes: 837eb4d21ecde7 ("NFC: trf7970a: add device tree option for 27MHz clock")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use unified device properties API in meaningful way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since we got rid of platform data, the driver may use GPIO descriptor
directly.
Looking deeply to the use of the GPIO pin it looks like it should be
a GPIO based reset control rather than custom GPIO handling. But this
is out of scope of the change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
I2C and SPI frameworks followed by IRQ framework do set
interrupt polarity correctly if it's properly specified in firmware
(ACPI or DT).
Get rid of the redundant trick when requesting interrupt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
It looks like there are two leftovers, at least one of which can leak
the resource (IRQ).
Convert both places to use managed variants of the functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
There is no platform code that uses i2c module table.
Remove it altogether and adjust ->probe() to be ->probe_new().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow gpio 0 to be used for reset signalling, and instead use negative
errnos to disable the reset functionality.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the USB-interface rather than parent USB-device device, which is
what this driver binds to, when registering the nci device.
Note that using the right device is important when dealing with device-
managed resources as the interface can be unbound independently of the
parent device.
Also note that private device pointer had already been set by
nfcmrvl_nci_register_dev() so the redundant assignment can therefore be
removed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Make sure to release the device-node reference when done parsing the
node.
Fixes: e097dc624f78 ("NFC: nfcmrvl: add UART driver")
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The nci-device was never deregistered in the event that
fw-initialisation failed.
Fix this by moving the firmware initialisation before device
registration since the firmware work queue should be available before
registering.
Note that this depends on a recent fix that moved device-name
initialisation back to to nci_allocate_device() as the
firmware-workqueue name is now derived from the nfc-device name.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support")
Cc: stable <stable@vger.kernel.org> # 4.4
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the nfc- rather than phy-device in firmware-management code that
needs a valid struct device.
This specifically fixes a NULL-pointer dereference in
nfcmrvl_fw_dnld_init() during registration when the underlying tty is
one end of a Unix98 pty.
Note that the driver still uses the phy device for any debugging, which
is fine for now.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support")
Cc: stable <stable@vger.kernel.org> # 4.4
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This specifically fixes resource leaks in the registration error paths.
Device-managed resources is a bad fit for this driver as devices can be
registered from the n_nci line discipline. Firstly, a tty may not even
have a corresponding device (should it be part of a Unix98 pty)
something which would lead to a NULL-pointer dereference when
registering resources.
Secondly, if the tty has a class device, its lifetime exceeds that of
the line discipline, which means that resources would leak every time
the line discipline is closed (or if registration fails).
Currently, the devres interface was only being used to request a reset
gpio despite the fact that it was already explicitly freed in
nfcmrvl_nci_unregister_dev() (along with the private data), something
which also prevented the resource leak at close.
Note that the driver treats gpio number 0 as invalid despite it being
perfectly valid. This will be addressed in a follow-up patch.
Fixes: b2fe288eac72 ("NFC: nfcmrvl: free reset gpio")
Fixes: 4a2b947f56b3 ("NFC: nfcmrvl: add chip reset management")
Cc: stable <stable@vger.kernel.org> # 4.2: b2fe288eac72
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Make sure to check the tty-device pointer before trying to access the
parent device to avoid dereferencing a NULL-pointer when the tty is one
end of a Unix98 pty.
Fixes: e097dc624f78 ("NFC: nfcmrvl: add UART driver")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Clean up coding style issues according to scripts/Lindent.
Some scripts/Lindent changes were reverted when it appeared
to make the code less readable or when it made the line run
over 80 characters.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The trf7970a driver uses the deprecated integer-based GPIO consumer
interface so convert it to use the new descriptor-based GPIO
consumer interface.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The 'vin-voltage-override' DT property is used by the trf7970a
driver to override the voltage presented to the driver by the
regulator subsystem. This is unnecessary as properly specifying
the regulator chain via DT properties will accomplish the same
thing. Therefore, remove support for 'vin-voltage-override'.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The last entry in the trf7970a_of_match[] table must be an empty
entry to demarcate the end of the table. Currently, there is a
comment indicating this but it is obvious so remove the comment.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The quirk indicated by the 'en2-rf-quirk' device tree property
is only relevant when there is a GPIO connected to the EN2 pin
of the trf7970a. This means we should only check for 'en2-rf-quirk'
when EN2 is specified in the 'ti,enable-gpios' property of the
device tree.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As of commit ce69b95ca4e4 ("NFC: Make EN2 pin optional in the
TRF7970A driver"), only the GPIO for the 'EN' enable pin needs
to be specified in the device tree so update the comments that
says both 'EN' and 'EN2' must be specified.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the trf7970a part has the bug related to 'en2-rf-quirk',
the GPIO connected to the EN2 pin will not be asserted by the
driver when powering up so it shouldn't be de-asserted when
powering down.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
*(u8 *)skb_put(skb, 1) = c;
Add skb_put_u8() for this case, and use it across the code,
using the following spatch:
@@
expression SKB, C, S;
typedef u8;
identifier fn = {skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
*(u8 *)skb_put(skb, 2) = c;
which would be wrong anyway since the second byte wouldn't be
initialized.
Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* if a local variable of type uint16_t is unaligned, your compiler is FUBAR
* the whole point of get_unaligned_... is to avoid memcpy + ..._to_cpu().
Using it *after* memcpy() (into aligned object, no less) is pointless.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
fix for WARN:
usb 3-2.4.1: NFC: Exchanging data failed (error 0x13)
llcp: nfc_llcp_recv: err -5
llcp: nfc_llcp_symm_timer: SYMM timeout
------------[ cut here ]------------
WARNING: CPU: 1 PID: 26397 at .../drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x370/0x550
transfer buffer not dma capable
[...]
Workqueue: events nfc_llcp_timeout_work [nfc]
Call Trace:
? dump_stack+0x46/0x5a
? __warn+0xb9/0xe0
? warn_slowpath_fmt+0x5a/0x80
? usb_hcd_map_urb_for_dma+0x370/0x550
? usb_hcd_submit_urb+0x2fb/0xa60
? dequeue_entity+0x3f2/0xc30
? pn533_usb_send_ack+0x5d/0x80 [pn533_usb]
? pn533_usb_abort_cmd+0x13/0x20 [pn533_usb]
? pn533_dep_link_down+0x32/0x70 [pn533]
? nfc_dep_link_down+0x87/0xd0 [nfc]
[...]
usb 3-2.4.1: NFC: Exchanging data failed (error 0x13)
llcp: nfc_llcp_recv: err -5
llcp: nfc_llcp_symm_timer: SYMM timeout
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TRF7970A has configuration options for supporting hardware designs
with 1.8 Volt or 3.3 Volt IO. This commit adds a device tree option,
using a fixed regulator binding, for setting the io voltage to match
the hardware configuration. If no option is supplied it defaults to
3.3 volt configuration.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TRF7970A has configuration options to support hardware designs
which use a 27.12MHz clock. This commit adds a device tree option
'clock-frequency' to support configuring the this chip for default
13.56MHz clock or the optional 27.12MHz clock.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Another place in the code that unveils non-tested at all ACPI case.
Use unified device property API in meaningful way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since we got rid of platform data, the driver may use GPIO descriptor
directly.
Looking deeply to the use of the GPIO pin it looks like it should be
a fixed voltage regulator rather than custom GPIO handling. But this
is out of scope of the change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
I2C framework followed by IRQ framework does set interrupt polarity
correctly if it's properly specified in firmware (ACPI or DT).
Get rid of the redundant trick when requesting interrupt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We return -ENODEV if ACPI provides a GPIO resource. Looks really wrong.
If it has even been tested?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The error handling will be neat and short when using managed resources.
Convert the driver to use devm_request_threaded_irq().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
