aboutsummaryrefslogtreecommitdiff
path: root/drivers/phy/Makefile
AgeCommit message (Collapse)Author
2020-12-05PHY: Ingenic: Add USB PHY driver using generic PHY framework.周琰杰 (Zhou Yanjie)
Used the generic PHY framework API to create the PHY, this driver supoorts USB OTG PHY used in JZ4770 SoC, JZ4775 SoC, JZ4780 SoC, X1000 SoC, X1830 SoC and X2000 SoC. Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20201116141906.11758-4-zhouyanjie@wanyeetech.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-09-11phy: Add USB3 PHY support for Intel LGM SoCRamuthevar Vadivel Murugan
Add support for USB PHY on Intel LGM SoC. Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20200828022312.52724-3-vadivel.muruganx.ramuthevar@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-06-29phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit TransceiverAnurag Kumar Vulisha
Xilinx ZynqMP SoCs have a Gigabit Transceiver with four lanes. All the high speed peripherals such as USB, SATA, PCIE, Display Port and Ethernet SGMII can rely on any of the four GT lanes for PHY layer. This patch adds driver for that ZynqMP GT core. Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://lore.kernel.org/r/20200629120054.29338-3-laurent.pinchart@ideasonboard.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-06-24phy: Remove CONFIG_ARCH_* check for related subdir in MakefileTiezhu Yang
If CONFIG_ARCH_ROCKCHIP is not set but COMPILE_TEST is set, the file in the subdir rockchip can not be built due to CONFIG_ARCH_ROCKCHIP check in drivers/phy/Makefile. Since the related configs in drivers/phy/rockchip/Kconfig depend on ARCH_ROCKCHIP, so remove CONFIG_ARCH_ROCKCHIP check for subdir rockchip in drivers/phy/Makefile. The other CONFIG_ARCH_* about allwinner, amlogic, mediatek, renesas and tegra have the same situation, so remove them too. Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/1590412138-13903-2-git-send-email-yangtiezhu@loongson.cn Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-14phy: intel-lgm-emmc: Add support for eMMC PHYRamuthevar Vadivel Murugan
Add support for eMMC PHY on Intel's Lightning Mountain SoC. Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-08-23phy: enable compile-testing for the Lantiq PHY driversMartin Blumenstingl
Unconditionally include the lantiq subdirectory in the phy Makefile. All drivers in there have their dependencies maintained. One of these (optional) dependencies is COMPILE_TEST, however this can only be evaluated when Kconfig scans the lantiq subdirectory. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-12-12phy: dphy: Add configuration helpersMaxime Ripard
The MIPI D-PHY spec defines default values and boundaries for most of the parameters it defines. Introduce helpers to help drivers get meaningful values based on their current parameters, and validate the boundaries of these parameters if needed. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-12-12phy: add driver for Freescale i.MX8MQ USB3 PHYLi Jun
This is a cleaned up port of the downstream i.MX8MQ USB3 PHY driver. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-10-26Merge tag 'usb-4.20-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big USB/PHY driver patches for 4.20-rc1 Lots of USB changes in here, primarily in these areas: - typec updates and new drivers - new PHY drivers - dwc2 driver updates and additions (this old core keeps getting added to new devices.) - usbtmc major update based on the industry group coming together and working to add new features and performance to the driver. - USB gadget additions for new features - USB gadget configfs updates - chipidea driver updates - other USB gadget updates - USB serial driver updates - renesas driver updates - xhci driver updates - other tiny USB driver updates All of these have been in linux-next for a while with no reported issues" * tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits) usb: phy: ab8500: silence some uninitialized variable warnings usb: xhci: tegra: Add genpd support usb: xhci: tegra: Power-off power-domains on removal usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten usbip: tools: fix atoi() on non-null terminated string USB: misc: appledisplay: fix backlight update_status return code phy: phy-pxa-usb: add a new driver usb: host: add DT bindings for faraday fotg2 usb: host: ohci-at91: fix request of irq for optional gpio usb/early: remove set but not used variable 'remain_length' usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc usb: typec: tcpm: Report back negotiated PPS voltage and current USB: core: remove set but not used variable 'udev' usb: core: fix memory leak on port_dev_path allocation USB: net2280: Remove ->disconnect() callback from net2280_pullup() usb: dwc2: disable power_down on rockchip devices usb: gadget: udc: renesas_usb3: add support for r8a77990 dt-bindings: usb: renesas_usb3: add bindings for r8a77990 usb: gadget: udc: renesas_usb3: Add r8a774a1 support USB: serial: cypress_m8: remove set but not used variable 'iflag' ...
2018-10-05phy: add driver for Microsemi Ocelot SerDes muxingQuentin Schulz
The Microsemi Ocelot can mux SerDes lanes (aka macros) to different switch ports or even make it act as a PCIe interface. This adds support for the muxing of the SerDes. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-10phy: socionext: add USB3 PHY driver for UniPhier SoCKunihiko Hayashi
Add a driver for PHY interface built into USB3 controller implemented in UniPhier SoCs. This driver supports High-Speed PHY and Super-Speed PHY. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Motoya Tanigawa <tanigawa.motoya@socionext.com> Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-09-10phy: Add driver for Cadence MHDP DisplayPort SD0801 PHYScott Telford
Add driver for the Cadence SD0801 "Torrent" PHY used with the Cadence MHDP DisplayPort Tx controller. Integration with the MHDP driver will be the subject of another commit. Signed-off-by: Scott Telford <stelford@cadence.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-15Merge branch '4.14-features' of ↵Linus Torvalds
git://git.linux-mips.org/pub/scm/ralf/upstream-linus Pull MIPS updates from Ralf Baechle: "This is the main pull request for 4.14 for MIPS; below a summary of the non-merge commits: CM: - Rename mips_cm_base to mips_gcr_base - Specify register size when generating accessors - Use BIT/GENMASK for register fields, order & drop shifts - Add cluster & block args to mips_cm_lock_other() CPC: - Use common CPS accessor generation macros - Use BIT/GENMASK for register fields, order & drop shifts - Introduce register modify (set/clear/change) accessors - Use change_*, set_* & clear_* where appropriate - Add CM/CPC 3.5 register definitions - Use GlobalNumber macros rather than magic numbers - Have asm/mips-cps.h include CM & CPC headers - Cluster support for topology functions - Detect CPUs in secondary clusters CPS: - Read GIC_VL_IDENT directly, not via irqchip driver DMA: - Consolidate coherent and non-coherent dma_alloc code - Don't use dma_cache_sync to implement fd_cacheflush FPU emulation / FP assist code: - Another series of 14 commits fixing corner cases such as NaN propgagation and other special input values. - Zero bits 32-63 of the result for a CLASS.D instruction. - Enhanced statics via debugfs - Do not use bools for arithmetic. GCC 7.1 moans about this. - Correct user fault_addr type Generic MIPS: - Enhancement of stack backtraces - Cleanup from non-existing options - Handle non word sized instructions when examining frame - Fix detection and decoding of ADDIUSP instruction - Fix decoding of SWSP16 instruction - Refactor handling of stack pointer in get_frame_info - Remove unreachable code from force_fcr31_sig() - Convert to using %pOF instead of full_name - Remove the R6000 support. - Move FP code from *_switch.S to *_fpu.S - Remove unused ST_OFF from r2300_switch.S - Allow platform to specify multiple its.S files - Add #includes to various files to ensure code builds reliable and without warning.. - Remove __invalidate_kernel_vmap_range - Remove plat_timer_setup - Declare various variables & functions static - Abstract CPU core & VP(E) ID access through accessor functions - Store core & VP IDs in GlobalNumber-style variable - Unify checks for sibling CPUs - Add CPU cluster number accessors - Prevent direct use of generic_defconfig - Make CONFIG_MIPS_MT_SMP default y - Add __ioread64_copy - Remove unnecessary inclusions of linux/irqchip/mips-gic.h GIC: - Introduce asm/mips-gic.h with accessor functions - Use new GIC accessor functions in mips-gic-timer - Remove counter access functions from irq-mips-gic.c - Remove gic_read_local_vp_id() from irq-mips-gic.c - Simplify shared interrupt pending/mask reads in irq-mips-gic.c - Simplify gic_local_irq_domain_map() in irq-mips-gic.c - Drop gic_(re)set_mask() functions in irq-mips-gic.c - Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(), gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c. - Convert remaining shared reg access, local int mask access and remaining local reg access to new accessors - Move GIC_LOCAL_INT_* to asm/mips-gic.h - Remove GIC_CPU_INT* macros from irq-mips-gic.c - Move various definitions to the driver - Remove gic_get_usm_range() - Remove __gic_irq_dispatch() forward declaration - Remove gic_init() - Use mips_gic_present() in place of gic_present and remove gic_present - Move gic_get_c0_*_int() to asm/mips-gic.h - Remove linux/irqchip/mips-gic.h - Inline __gic_init() - Inline gic_basic_init() - Make pcpu_masks a per-cpu variable - Use pcpu_masks to avoid reading GIC_SH_MASK* - Clean up mti, reserved-cpu-vectors handling - Use cpumask_first_and() in gic_set_affinity() - Let the core set struct irq_common_data affinity microMIPS: - Fix microMIPS stack unwinding on big endian systems MIPS-GIC: - SYNC after enabling GIC region NUMA: - Remove the unused parent_node() macro R6: - Constify r2_decoder_tables - Add accessor & bit definitions for GlobalNumber SMP: - Constify smp ops - Allow boot_secondary SMP op to return errors VDSO: - Drop gic_get_usm_range() usage - Avoid use of linux/irqchip/mips-gic.h Platform changes: Alchemy: - Add devboard machine type to cpuinfo - update cpu feature overrides - Threaded carddetect irqs for devboards AR7: - allow NULL clock for clk_get_rate BCM63xx: - Fix ENETDMA_6345_MAXBURST_REG offset - Allow NULL clock for clk_get_rate CI20: - Enable GPIO and RTC drivers in defconfig - Add ethernet and fixed-regulator nodes to DTS Generic platform: - Move Boston and NI 169445 FIT image source to their own files - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Allow filtering enabled boards by requirements - Don't explicitly disable CONFIG_USB_SUPPORT - Bump default NR_CPUS to 16 JZ4700: - Probe the jz4740-rtc driver from devicetree Lantiq: - Drop check of boot select from the spi-falcon driver. - Drop check of boot select from the lantiq-flash MTD driver. - Access boot cause register in the watchdog driver through regmap - Add device tree binding documentation for the watchdog driver - Add docs for the RCU DT bindings. - Convert the fpi bus driver to a platform_driver - Remove ltq_reset_cause() and ltq_boot_select( - Switch to a proper reset driver - Switch to a new drivers/soc GPHY driver - Add an USB PHY driver for the Lantiq SoCs using the RCU module - Use of_platform_default_populate instead of __dt_register_buses - Enable MFD_SYSCON to be able to use it for the RCU MFD - Replace ltq_boot_select() with dummy implementation. Loongson 2F: - Allow NULL clock for clk_get_rate Malta: - Use new GIC accessor functions NI 169445: - Add support for NI 169445 board. - Only include in 32r2el kernels Octeon: - Add support for watchdog of 78XX SOCs. - Add support for watchdog of CN68XX SOCs. - Expose support for mips32r1, mips32r2 and mips64r1 - Enable more drivers in config file - Add support for accessing the boot vector. - Remove old boot vector code from watchdog driver - Define watchdog registers for 70xx, 73xx, 78xx, F75xx. - Make CSR functions node aware. - Allow access to CIU3 IRQ domains. - Misc cleanups in the watchdog driver Omega2+: - New board, add support and defconfig Pistachio: - Enable Root FS on NFS in defconfig Ralink: - Add Mediatek MT7628A SoC - Allow NULL clock for clk_get_rate - Explicitly request exclusive reset control in the pci-mt7620 PCI driver. SEAD3: - Only include in 32 bit kernels by default VoCore: - Add VoCore as a vendor t0 dt-bindings - Add defconfig file" * '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits) MIPS: Refactor handling of stack pointer in get_frame_info MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems MIPS: microMIPS: Fix decoding of swsp16 instruction MIPS: microMIPS: Fix decoding of addiusp instruction MIPS: microMIPS: Fix detection of addiusp instruction MIPS: Handle non word sized instructions when examining frame MIPS: ralink: allow NULL clock for clk_get_rate MIPS: Loongson 2F: allow NULL clock for clk_get_rate MIPS: BCM63XX: allow NULL clock for clk_get_rate MIPS: AR7: allow NULL clock for clk_get_rate MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset mips: Save all registers when saving the frame MIPS: Add DWARF unwinding to assembly MIPS: Make SAVE_SOME more standard MIPS: Fix issues in backtraces MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree MIPS: Ci20: Enable RTC driver watchdog: octeon-wdt: Add support for 78XX SOCs. watchdog: octeon-wdt: Add support for cn68XX SOCs. watchdog: octeon-wdt: File cleaning. ...
2017-09-04phy: Add an USB PHY driver for the Lantiq SoCs using the RCU moduleHauke Mehrtens
This driver starts the DWC2 core(s) built into the XWAY SoCs and provides the PHY interfaces for each core. The phy instances can be passed to the dwc2 driver, which already supports the generic phy interface. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Rob Herring <robh@kernel.org> Cc: martin.blumenstingl@googlemail.com Cc: john@phrozen.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17127/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-20phy: ralink-usb: add driver for Mediatek/RalinkJohn Crispin
Add a driver to setup the USB phy on Mediatek/Ralink SoCs. The driver sets up power and host mode, but also needs to configure PHY registers for the MT7628 and MT7688. Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-08-20phy: phy-mt65xx-usb3: add mediatek directory and rename fileChunfeng Yun
The driver is actually for T-PHY which supports USB3.0, PCIe and SATA, and supports more SoCs now, but not just only for series of mt65xx SoCs, so the name of file, data struct, functions etc with 'mt65xx' may cause misunderstanding when new SoCs are supported. Here rename them to reflect the real functions and also enhance readability. And also update MAINTAINERS file to reflect the correct driver Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-06-06phy: cpcap-usb: Add CPCAP PMIC USB supportTony Lindgren
Some Motorola phones like droid 4 use a custom CPCAP PMIC that has a multiplexing USB PHY. This USB PHY can operate at least in four modes using pin multiplexing and two control GPIOS: - Pass through companion PHY for the SoC USB PHY - ULPI PHY for the SoC - Pass through USB for the modem - UART debug console for the SoC This patch adds support for droid 4 USB PHY and debug UART modes, support for other modes can be added later on as needed. Both peripheral and host mode are working for the USB. The host mode depends on the cpcap-charger driver for VBUS. VBUS and ID pin detection are done using cpcap-adc IIO ADC driver. Cc: devicetree@vger.kernel.org Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-06-01phy: Group vendor specific phy driversVivek Gautam
Adding vendor specific directories in phy to group phy drivers under their respective vendor umbrella. Also updated the MAINTAINERS file to reflect the correct directory structure for phy drivers. Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: David S. Miller <davem@davemloft.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-usb@vger.kernel.org Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-04-10phy: qcom-qmp: new qmp phy driver for qcom-chipsetsVivek Gautam
Qualcomm SOCs have QMP phy controller that provides support to a number of controller, viz. PCIe, UFS, and USB. Add a new driver, based on generic phy framework, for this phy controller. Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-04-10phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chipsVivek Gautam
PHY transceiver driver for QUSB2 phy controller that provides HighSpeed functionality for DWC3 controller present on Qualcomm chipsets. Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-03-09Revert "phy: Add USB3 PHY support for Broadcom NSP SoC"Rafał Miłecki
This reverts commit d7bc1a7d41bf ("phy: Add USB3 PHY support for Broadcom NSP SoC") as we already have driver for this PHY (shared by NS and NSP). It was added in commit e5666281d9ea ("phy: bcm-ns-usb3: new driver for USB 3.0 PHY on Northstar"). Instead of adding separated driver & duplicating code we should work on improving existing (old) one. Thanks to work done by Broadcom we know there is MDIO bus we weren't aware of & we know register names which makes initialization more clear. This is very valuable info and we should work on using it in existing driver afterwards. Acked-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-23Merge tag 'pci-v4.11-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: - add ASPM L1 substate support - enable PCIe Extended Tags when supported - configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx - increase VPD access timeout - add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432 - use new pci_irq_alloc_vectors() in more drivers - fix MSI affinity memory leak - remove unused MSI interfaces and update documentation - remove unused AER .link_reset() callback - avoid pci_lock / p->pi_lock deadlock seen with perf - serialize sysfs enable/disable num_vfs operations - move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and refactor so we can support both hosts and endpoints - add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers - add Rockchip system power management support - add Thunder-X cn81xx and cn83xx support - add Exynos 5440 PCIe PHY support * tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits) PCI: dwc: Remove dependency of designware on CONFIG_PCI PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host PCI: dwc: Split pcie-designware.c into host and core files PCI: dwc: designware: Fix style errors in pcie-designware.c PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc() PCI: dwc: all: Split struct pcie_port into host-only and core structures PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init() PCI: dwc: all: Rename cfg_read/cfg_write to read/write PCI: dwc: all: Use platform_set_drvdata() to save private data PCI: dwc: designware: Move register defines to designware header file PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code PCI: dra7xx: Group PHY API invocations PCI: dra7xx: Enable MSI and legacy interrupts simultaneously PCI: dra7xx: Add support to force RC to work in GEN1 mode PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional() PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory PCI: exynos: Support the PHY generic framework Documentation: binding: Modify the exynos5440 PCIe binding phy: phy-exynos-pcie: Add support for Exynos PCIe PHY Documentation: samsung-phy: Add exynos-pcie-phy binding ...
2017-02-21phy: phy-exynos-pcie: Add support for Exynos PCIe PHYJaehoon Chung
Add support for Generic PHY framework about Exynos SoCs. Current Exynos PCIe driver doesn't use the PHY framework, which makes it difficult to upstream the other Exynos variants because of different PHY registers. Move the codes relevant to PHY from Exnyos PCIe driver to PHY Exynos PCIe driver. [bhelgaas: depend on "OF && (ARCH_EXYNOS || COMPILE_TEST)", update copyright year, both per Vivek] Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Jingoo Han <jingoohan1@gmail.com> Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com> Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2017-01-27phy: Add USB3 PHY support for Broadcom NSP SoCYendapally Reddy Dhananjaya Reddy
This patch adds support for Broadcom NSP USB3 PHY Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-01-27phy: Add support for Qualcomm's USB HS phyStephen Boyd
The high-speed phy on qcom SoCs is controlled via the ULPI viewport. Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: <devicetree@vger.kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-01-27phy: Add support for Qualcomm's USB HSIC phyStephen Boyd
The HSIC USB controller on qcom SoCs has an integrated all digital phy controlled via the ULPI viewport. Cc: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Rob Herring <robh@kernel.org> Cc: <devicetree@vger.kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-11-18phy: stih41x-usb: Remove usb phy driver and dt bindingPeter Griffin
documentation. This phy is only used on STiH415/6 based silicon, and support for these SoC's is being removed from the kernel. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-11-18phy: phy-miphy365x: Remove miphy365 driver and dt bindingPeter Griffin
documentation. This phy is only used on STiH415/6 based silicon, and support for these SoC's is being removed from the kernel. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-11-18phy: meson: add USB2 PHY support for Meson8b and GXBBMartin Blumenstingl
This is a new driver for the USB PHY found in Meson8b and GXBB SoCs. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-09-10phy: Add USB Type-C PHY driver for rk3399Chris Zhong
Add a PHY provider driver for the rk3399 SoC Type-c PHY. The USB Type-C PHY is designed to support the USB3 and DP applications. The USB3 operates in SuperSpeed mode and the DP can operate at RBR, HBR and HBR2 data rates. This driver create 2 PHY devices separately for USB3 and DisplyPort, and registers them under the child node. Signed-off-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Guenter Roeck <groeck@chromium.org> Tested-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-09-10phy: add a driver for the Rockchip SoC internal PCIe PHYShawn Lin
This patch to add a generic PHY driver for rockchip PCIe PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-09-10phy: rockchip-inno-usb2: add a new driver for Rockchip usb2phyFrank Wang
The newer SoCs (rk3366, rk3399) take a different usb-phy IP block than rk3288 and before, and most of phy-related registers are also different from the past, so a new phy driver is required necessarily. Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Suggested-by: Heiko Stuebner <heiko@sntech.de> Suggested-by: Guenter Roeck <linux@roeck-us.net> Suggested-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-09-10phy: bcm-ns-usb3: new driver for USB 3.0 PHY on NorthstarRafał Miłecki
Northstar is a family of SoCs used in home routers. They have USB 2.0 and 3.0 controllers with PHYs that need to be properly initialized. This driver provides PHY init support in a generic way and can be bound with XHCI controller driver. There aren't any public datasheets from Broadcom so we can't have nice defines for all used bits. It means we just follow Broadcom's initialization procedure using their magic values. We were quite lucky actually that Broadcom put some comments in their SDK reference code explaining what given writes are responsible for. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-07-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Unified UDP encapsulation offload methods for drivers, from Alexander Duyck. 2) Make DSA binding more sane, from Andrew Lunn. 3) Support QCA9888 chips in ath10k, from Anilkumar Kolli. 4) Several workqueue usage cleanups, from Bhaktipriya Shridhar. 5) Add XDP (eXpress Data Path), essentially running BPF programs on RX packets as soon as the device sees them, with the option to mirror the packet on TX via the same interface. From Brenden Blanco and others. 6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet. 7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli. 8) Simplify netlink conntrack entry layout, from Florian Westphal. 9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido Schimmel, Yotam Gigi, and Jiri Pirko. 10) Add SKB array infrastructure and convert tun and macvtap over to it. From Michael S Tsirkin and Jason Wang. 11) Support qdisc packet injection in pktgen, from John Fastabend. 12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy. 13) Add NV congestion control support to TCP, from Lawrence Brakmo. 14) Add GSO support to SCTP, from Marcelo Ricardo Leitner. 15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni. 16) Support MPLS over IPV4, from Simon Horman. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits) xgene: Fix build warning with ACPI disabled. be2net: perform temperature query in adapter regardless of its interface state l2tp: Correctly return -EBADF from pppol2tp_getname. net/mlx5_core/health: Remove deprecated create_singlethread_workqueue net: ipmr/ip6mr: update lastuse on entry change macsec: ensure rx_sa is set when validation is disabled tipc: dump monitor attributes tipc: add a function to get the bearer name tipc: get monitor threshold for the cluster tipc: make cluster size threshold for monitoring configurable tipc: introduce constants for tipc address validation net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update() MAINTAINERS: xgene: Add driver and documentation path Documentation: dtb: xgene: Add MDIO node dtb: xgene: Add MDIO node drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset drivers: net: xgene: Use exported functions drivers: net: xgene: Enable MDIO driver drivers: net: xgene: Add backward compatibility drivers: net: phy: xgene: Add MDIO driver ...
2016-07-04phy: da8xx-usb: new driver for DA8xx SoC USB PHYDavid Lechner
This is a new phy driver for the SoC USB controllers on the TI DA8xx family of microcontrollers. The USB 1.1 PHY is just a simple on/off. The USB 2.0 PHY also allows overriding the VBUS and ID pins. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-06-10phy: Add Northstar2 PCI Phy supportPramod Kumar
Add PCI Phy support for Broadcom Northstar2 SoCs. This driver uses the interface from the iproc mdio mux driver to enable the devices respective phys. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jon Mason <jonmason@broadcom.com> Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-20Merge tag 'usb-4.7-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB updates from Greg KH: "Here's the big pull request for USB and PHY drivers for 4.7-rc1 Full details in the shortlog, but it's the normal major gadget driver updates, phy updates, new usbip code, as well as a bit of lots of other stuff. All have been in linux-next with no reported issues" * tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits) USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support USB: serial: fix minor-number allocation USB: serial: quatech2: fix use-after-free in probe error path USB: serial: mxuport: fix use-after-free in probe error path USB: serial: keyspan: fix debug and error messages USB: serial: keyspan: fix URB unlink USB: serial: keyspan: fix use-after-free in probe error path USB: serial: io_edgeport: fix memory leaks in probe error path USB: serial: io_edgeport: fix memory leaks in attach error path usb: Remove unnecessary space before operator ','. usb: Remove unnecessary space before open square bracket. USB: FHCI: avoid redundant condition usb: host: xhci-rcar: Avoid long wait in xhci_reset() usb/host/fotg210: remove dead code in create_sysfs_files usb: wusbcore: Do not initialise statics to 0. usb: wusbcore: Remove space before ',' and '(' . USB: serial: cp210x: clean up CRTSCTS flag code USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code USB: serial: cp210x: fix hardware flow-control disable USB: serial: option: add even more ZTE device ids ...
2016-04-30phy: bcm-ns-usb2: new driver for USB 2.0 PHY on NorthstarRafał Miłecki
Northstar is a family of SoCs used in home routers. They have USB 2.0 and 3.0 controllers with PHYs that need to be properly initialized. This driver provides PHY init support in a generic way and can be bound with an EHCI controller driver. There are (just a few) registers being defined in bcma header. It's because DMU/CRU registers will be also needed in other drivers. We will need them e.g. in PCIe controller/PHY driver and at some point probably in clock driver for BCM53573 chipset. By using include/linux/bcma/ we avoid code duplication. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-04-30phy: Add support for NS2 SATA3 PHY in Broadcom SATA3 PHY driverAnup Patel
This patch adds support for Broadcom NS2 SATA3 PHY in existing Broadcom SATA3 PHY driver. Signed-off-by: Anup Patel <anup.patel@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-04-29phy: Add Tegra XUSB pad controller supportThierry Reding
Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs. This hardware block used to be exposed as a pin controller, but it turns out that this isn't a good fit. The new driver and DT binding much more accurately describe the hardware and are more flexible in supporting new SoC generations. Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2016-04-29phy: Rename phy-brcmstb-sata driver to phy-brcm-sata driverAnup Patel
Currently, we have a common SATA3 PHY driver for all Broadcom STB SoCs. This driver can be extended and re-used for Broadcom iProc SoCs having same SATA3 PHY. This patch renames existing Broadcom STB SATA3 PHY driver to common Broadcom SATA3 PHY driver to share this PHY driver across Broadcom SoCs. Signed-off-by: Anup Patel <anup.patel@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01phy: Add driver for rockchip Display Port PHYYakir Yang
Add phy driver for the Rockchip DisplayPort PHY module. This is required to get DisplayPort working in Rockchip SoCs. Signed-off-by: Yakir Yang <ykk@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-01phy: add a driver for the Rockchip SoC internal eMMC PHYShawn Lin
This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-12-20phy: add phy-hi6220-usbZhangfei Gao
Support hi6220 use phy for HiKey board Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-12-20phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driverYoshihiro Shimoda
This patch adds support for R-Car generation 3 USB2 PHY driver. This SoC has 3 EHCI/OHCI channels, and the channel 0 is shared with the HSUSB (USB2.0 peripheral) device. And each channel has independent registers about the PHYs. So, the purpose of this driver is: 1) initializes some registers of SoC specific to use the {ehci,ohci}-platform driver. 2) detects id pin to select host or peripheral on the channel 0. For now, this driver only supports 1) above. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-10-06phy: cygnus: pcie: Add Cygnus PCIe PHY supportRay Jui
This patch adds the PCIe PHY support for the Broadcom PCIe RC interface on Cygnus Signed-off-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Arun Parameswaran <aparames@broadcom.com> Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-10-06phy: add usb3.0 phy driver for mt65xx SoCsChunfeng Yun
support usb3.0 phy of mt65xx SoCs Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25phy: add lpc18xx usb otg phy driverJoachim Eastwood
Add PHY driver for the internal USB OTG PHY found on NXP LPC18xx and LPC43xx devices. This driver takes care of enabling the PHY in CREG (syscon) and setting the required clock frequency. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-06-27Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds
Pull MIPS updates from Ralf Baechle: - Improvements to the tlb_dump code - KVM fixes - Add support for appended DTB - Minor improvements to the R12000 support - Minor improvements to the R12000 support - Various platform improvments for BCM47xx - The usual pile of minor cleanups - A number of BPF fixes and improvments - Some improvments to the support for R3000 and DECstations - Some improvments to the ATH79 platform support - A major patchset for the JZ4740 SOC adding support for the CI20 platform - Add support for the Pistachio SOC - Minor BMIPS/BCM63xx platform support improvments. - Avoid "SYNC 0" as memory barrier when unlocking spinlocks - Add support for the XWR-1750 board. - Paul's __cpuinit/__cpuinitdata cleanups. - New Malta CPU board support large memory so enable ZONE_DMA32. * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits) MIPS: spinlock: Adjust arch_spin_lock back-off time MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA MIPS: BCM47xx: Simplify handling SPROM revisions MIPS: Cobalt Don't use module_init in non-modular MTD registration. MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/ MIPS: use for_each_sg() MIPS: BCM47xx: Don't select BCMA_HOST_PCI MIPS: BCM47xx: Add helper variable for storing NVRAM length MIPS: IRQ/IP27: Move IRQ allocation API to platform code. MIPS: Replace smp_mb with release barrier function in unlocks. MIPS: i8259: DT support MIPS: Malta: Basic DT plumbing MIPS: include errno.h for ENODEV in mips-cm.h MIPS: Define GCR_GIC_STATUS register fields MIPS: BPF: Introduce BPF ASM helpers MIPS: BPF: Use BPF register names to describe the ABI MIPS: BPF: Move register definition to the BPF header MIPS: net: BPF: Replace RSIZE with SZREG MIPS: BPF: Free up some callee-saved registers MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers ...