| Age | Commit message (Collapse) | Author |
|---|
|
Add support for SAMA7G5 including reset_controller_dev support for 3 lines
(which are USB PHYs).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
SAMA7G5 reset controller has 5 extra lines that goes to different devices
(3 lines to USB PHYs, 1 line to DDR controller, 1 line to DDR PHY
controller). These reset lines could be requested by different controller
drivers (e.g. USB PHY driver) and these controllers' drivers could
assert/deassert these lines when necessary. Thus add support for
reset_controller_dev which brings this functionality.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add struct at91_reset_data to keep per platform related information.
This is a prerequisite for adding reset_controller_dev support.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Document structures and enums.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
|
|
Merge power-supply fixes, that missed the v5.18 merge window
into power-supply's for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The Tosa device (Sharp SL-6000) has a mishmash driver set-up
for the Toshiba TC6393xb MFD that includes a battery charger
and touchscreen and has some kind of relationship to the SoC
sound driver for the AC97 codec. Other devices define a chip
like this but seem only half-implemented, not really handling
battery charging etc.
This patch switches the Toshiba MFD device to provide GPIO
descriptors to the battery charger and SoC codec. As a result
some descriptors need to be moved out of the Tosa boardfile
and new one added: all SoC GPIO resources to these drivers
now comes from the main boardfile, while the MFD provide
GPIOs for its portions.
As a result we can request one GPIO from our own GPIO chip
and drop two hairy callbacks into the board file.
This platform badly needs to have its drivers split up and
converted to device tree probing to handle this quite complex
relationship in an orderly manner. I just do my best in solving
the GPIO descriptor part of the puzzle. Please don't ask me
to fix everything that is wrong with these driver to todays
standards, I am just trying to fix one aspect. I do try to
use modern devres resource management and handle deferred
probe using new functions where appropriate.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Dirk Opfer <dirk@opfer-online.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When the Capacity Inaccurate flag is set, the chip still provides data
about the battery, albeit inaccurate. Instead of discarding capacity
values for CI=1, expose the stale data and use the
POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED property to indicate that the
values should be used with care.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The workqueue is allocated in bind() but all interrupts are
registered in probe().
Some interrupts put work on the workqueue, which can have
bad side effects.
Allocate the workqueue in probe() instead, destroy it in
.remove() and make unbind() simply flush the workqueue.
Fixes: 1c1f13a006ed ("power: supply: ab8500: Move to componentized binding")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
quirk
Some "T3 MRD" mini-PCs / HDMI-sticks without a battery use a different
value then "5.11" for their DMI BIOS version field.
Drop the BIOS version check so that the no-battery "T3 MRD" DMI quirk
applies to these too.
Fixes: 3a06b912a5ce ("power: supply: axp288_fuel_gauge: Make "T3 MRD" no_battery_list DMI entry more generic")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Commit 3a06b912a5ce ("power: supply: axp288_fuel_gauge: Make "T3 MRD"
no_battery_list DMI entry more generic") added a generic no-battery DMI
match for many mini-PCs / HDMI-sticks which use "T3 MRD" as their DMI
board-name.
It turns out that the One Mix 1 mini laptop also uses "T3 MRD" for its
DMI boardname and it also has its chassis-type wrongly set to a value
of "3" (desktop). This was causing the axp288_fuel_gauge driver to
disable battery reporting because this matches the no-battery DMI
list entry for generic "T3 MRD" mini-PCs.
Change the no-battery DMI list into a quirks DMI list and add a
specific match for the One Mix 1 mini laptop before the generic
"T3 MRD" no-battery quirk entry to fix this.
Fixes: 3a06b912a5ce ("power: supply: axp288_fuel_gauge: Make "T3 MRD" no_battery_list DMI entry more generic")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
As we rely on pointers in the battery info to be zero-initialized
such as in the helper function power_supply_supports_vbat2ri()
we certainly need to allocate the struct power_supply_battery_info
with kzalloc() as well. Else this happens:
Unable to handle kernel paging request at virtual address 00280000
(...)
PC is at power_supply_vbat2ri+0x50/0x12c
LR is at ab8500_fg_battery_resistance+0x34/0x108
Fixes: e9e7d165b4b0 ("power: supply: Support VBAT-to-Ri lookup tables")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Otherwise power_supply_get_battery_info always returns -ENODEV
on devices that do not have a static battery, even when a simple
battery is found.
Fixes: c8aee3f41cb8 ("power: supply: Static data for Samsung batteries")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Two of the batteries were missing charging restart voltages,
meaning they can drain if the algorithm relies on restarting
charging at this voltage. Fix it up.
Fixes: c8aee3f41cb8 ("power: supply: Static data for Samsung batteries")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
|
|
The HRTimer in the AB8500 charging code is using CLOCK_REALTIME
to set an alarm some hours forward in time +/- 5 min for a safety
timer.
I have observed that this will sometimes fire sporadically
early when charging a battery with the result that
charging stops.
As CLOCK_REALTIME can be subject to adjustments of time from
sources such as NTP, this cannot be trusted and will likely
for example fire events if the clock is set forward some hours
by say NTP.
Use CLOCK_MONOTONIC as indicated in other instances and the
problem goes away. Also initialize the timer to REL mode
as this is what will be used later.
Fixes: 257107ae6b9b ("ab8500-chargalg: Use hrtimer")
Cc: Lee Jones <lee.jones@linaro.org>
Suggested-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver supports several chip variants which all share the same I2C
register interface. Since the chip will turn off and become inaccessible
under conditions outside of software control (e.g. upon button press or
input voltage removal), some special handling is needed to delay the
initialization of the IC until it is accessible.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Kernel test robot reported below warning ->
drivers/power/supply/ab8500_chargalg.c:790:13: warning:
variable 'delta_i_ua' set but not used [-Wunused-but-set-variable]
Remove unused variable delta_i_ua.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
Eliminate the follow coccicheck warning:
./drivers/power/supply/da9150-fg.c:524:2-9: line 524 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There are a few spelling mistakes in comments and in a dev_err
error message. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We add the line impedance to the inner resistance determined
from the battery voltage or other means to improve the
capacity estimations.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In free_charger_irq(), there is no free for 'WM8350_IRQ_CHG_FAST_RDY'.
Therefore, it should be better to add it in order to avoid the memory leak.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
If we detect a Samsung SDI battery, we return a static
struct power_supply_battery_info and avoid looking further.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Augment the AB8500 fuel gauge to use the VBAT-to-Ri method of
estimating the internal resistance if possible. Else fall back
to using the temperature-to-Ri or just the default Ri.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In Samsung devices, the method used to compensate for temperature,
age, load etc is by way of VBAT to Ri tables, which correlates the
battery voltage under load (VBAT) to an internal resistance (Ri).
Using this Ri and a measurement of the current out of the battery
(IBAT) the open circuit voltage (OCV) can be calculated as:
OCV = VBAT - (Ri * IBAT)
The details are described in comments to struct
power_supply_battery_info in the commit.
Since not all batteries supply this VBAT-to-Ri data, the fallback
method to use the temperature-to-Ri lookup table can also be used
as a fallback.
Add two helper functions to check if we have the tables needed for
using power_supply_vbat2ri() or power_supply_temp2resist_simple()
respectively, so capacity estimation code can choose which one
to employ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The Battery Type Indicator (BTI) resistor is a resistor mounted
between a special terminal on the battery and ground. By sending
a fixed current (such as 7mA) through this resistor and measuring
the voltage over it, the resistance can be determined, and this
verifies the battery type.
Typical side view of the battery:
o o o
GND BTI +3.8V
Typical example of the electrical layout:
+3.8 V BTI
| |
| + |
_______ [ ] 7kOhm
___ |
| |
| |
GND GND
By verifying this resistance before attempting to charge the
battery we add an additional level of security.
In some systems this is used for plug-and-play of batteries with
different capacity. In other cases, this is merely used to verify
that the right type of battery is connected, if several batteries
have the same physical shape and can be plugged into the same
slot. Sometimes this is just a surplus security mechanism.
Nokia and Samsung among many other vendors are known to use these
BTI resistors.
Add the BTI properties to struct power_supply_battery_info and
switch the AB8500 charger code over to using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The AB8500 code is using a special current and voltage setting
when the battery is in "alert mode", i.e. when it is starting
to go outside normal operating conditions so it is too
cold or too hot. This makes sense as a way for the charging
algorithm to deal with hostile environments.
Add the needed members to the struct power_supply_battery_info,
and switch the AB8500 charging code over to using this.
Reviewed-by: Matti Vaittineen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Maintenance charging is the phase of keeping up the charge
after the battery has charged fully using CC/CV charging.
This can be done in many successive phases and is usually
done with a slightly lower constant voltage than CV, and
a slightly lower allowed current.
Add an array of maintenance charging points each with a
current, voltage and safety timer, and add helper functions
to use these. Migrate the AB8500 code over.
This is used in several Samsung products using the AB8500
and these batteries and their complete parameters will
be added later as full examples, but the default battery
in the AB8500 code serves as a reasonable example so far.
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
We need the driver core fix in here as well for future changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
5V Vbus boost is on
Recently userspace has started switching power_supply class devices with
a charge_type psy-property between fast and trickle charge mode, see:
https://gitlab.freedesktop.org/hadess/power-profiles-daemon/-/issues/85
Before this patch bq24190_charger_set_charge_type() would unconditionally
write charging or none to the BQ24190_REG_POC_CHG_CONFIG bits, replacing
the otg setting of those bits when the OTG 5V Vbus boost converter was on,
turning the 5V Vbus off, removing the power from any attached peripherals.
This fixes this by keeping track of otg_vbus_enabled and the requested
charger_type settings and when otg_vbus_enabled is true, delay applying
the charger_type until the 5V boost converter is turned off.
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4e0 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use the common compare helper from component.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20220214060819.7334-22-yong.wu@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use devm_delayed_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver only uses managed resources, except for the delayed work, if
it is used.
Use devm_delayed_work_autocancel() to also manage the delayed work.
The error handling path of the probe and the remove function can both be
removed.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This driver can use an interrupt or polling in order get the charger's
status.
When using polling, a delayed work is used.
However, the remove() function unconditionally call
cancel_delayed_work_sync(), even if the delayed work is not used and is not
initialized.
In order to fix it, use devm_delayed_work_autocancel() and remove the now
useless remove() function.
Fixes: feb583e37f8a ("power: supply: add sbs-charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This patch remaps the bypass operation from POWER_SUPPLY_CHARGE_TYPE_FAST
to POWER_SUPPLY_CHARGE_TYPE_BYPASS.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Adds a POWER_SUPPLY_CHARGE_TYPE_BYPASS option to the POWER_SUPPLY_PROP_CHARGE_TYPE
property to facilitate bypass charging operation.
In bypass charging operation, the charger bypasses the charging path around the
integrated converter allowing for a "smart" wall adaptor to perform the power
conversion externally.
This operational mode is critical for the USB PPS standard of power adaptors and is
becoming a common feature in modern charging ICs such as:
- BQ25980
- BQ25975
- BQ25960
- LN8000
- LN8410
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use devm_work_autocancel() instead of hand-writing it.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The smb347 has a very sparse register map (the maximum register is 0x3f but
less than 10% of the possible registers appear to be defined) and doesn't
have any hardware defaults specified so the sparser data structure of an
rbtree is a better fit for it's needs than a flat cache. Since it uses I2C
for the control interface there is no performance concern with the slightly
more involved code so let's convert it.
This will mean we avoid any issues created by assuming that any previously
unaccessed registers hold a value that doesn't match what's in the hardware
(eg, an _update_bits() suppressing a write).
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.
For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.
This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.
As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.
Set Vhold to 4.4V to fix the slow charging issue on various devices.
There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.
Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
