Age | Commit message (Collapse) | Author |
|
IRIG and DCF output time in UTC, but the timecard operates
on TAI internally. Add an attribute node which allows adding
an offset to these modes before output.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRIG-B has several different output formats, the timecard defaults
to using B007. Add a control which selects different output modes.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRIG (Inter-range Instrumentation Group) timecode format on
one of the SMA output channels is provided by the IRIG master
FPGA block. Enable the master when the IRIG output format is
selected on either one of the output channels.
By default, the output is in B007 format.
DCF output format is provided by the DCF master block.
Also enable the IRIG and DCF slaves, which parse an incoming
signal from the external SMA connectors, and may be used to
adjust the PHC.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest firmware for the TimeCard adds selectable signals for
the SMA input/outputs. Add support for SMA selectors, and the
GPIO controls needed for steering signals.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware may provide a third signal timestamper, so make it
available for use.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a resource could not be registered, report the name of
the resource and the error code.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TimeCard exposes different resources, which may have their
own irqs. Space for the irqs is allocated through a MSI or MSI-X
interrupt vector. On some platforms, the interrupt allocation
fails.
Rather than making this fatal, just skip exposing those resources.
The main timecard functionality (that of a PTP clock) will work
without the additional resources.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an I2C controller isn't present, don't try and read the I2C flash.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only display the TOD information if there is a corresponding
TOD resource.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the xilinx i2c driver parameters to the resource block instead
of hardcoding things in the registration functions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and WP
Also correct how initialize_dco_operating_mode is called
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we don't need to support new 5.2 functions but different register
addresses
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not need since TCS firmware file will configure it properlly.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the 'imply' statements, these apparently are not doing
what I expected. Platform modules which are used by the driver
still need to be enabled in the overall config for them to be
used, but there isn't a hard dependency on them.
Use 'depend' for selectable modules which provide functions
used directly by the driver.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/ptp/Kconfig:
55c8fca1dae1 ("ptp_pch: Restore dependency on PCI")
e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NET doesn't imply NET_DEVLINK. Select this separately, so that
random config combinations don't complain.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If ptp_ocp_device_init() fails, pci_disable_device() is skipped.
Fix the error handling so this case is covered. Update ptp_ocp_remove()
so the normal exit path is identical.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If attempting to flash the firmware with a blob of size 0,
the entire write loop is skipped and the uninitialized err
is returned. Fix by setting to 0 first.
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix kconfig warning on arch/s390/:
WARNING: unmet direct dependencies detected for SERIAL_8250
Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && !S390 [=y]
Selected by [m]:
- PTP_1588_CLOCK_OCP [=m] && PTP_1588_CLOCK [=m] && HAS_IOMEM [=y] && PCI [=y] && SPI [=y] && I2C [=m] && MTD [=m]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h
9e26680733d5 ("bnxt_en: Update firmware call to retrieve TX PTP timestamp")
9e518f25802c ("bnxt_en: 1PPS functions to configure TSIO pins")
099fdeda659d ("bnxt_en: Event handler for PPS events")
kernel/bpf/helpers.c
include/linux/bpf-cgroup.h
a2baf4e8bb0f ("bpf: Fix potentially incorrect results with bpf_get_local_storage()")
c7603cfa04e7 ("bpf: Add ambient BPF runtime context stored in current")
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c
5957cc557dc5 ("net/mlx5: Set all field of mlx5_irq before inserting it to the xarray")
2d0b41a37679 ("net/mlx5: Refcount mlx5_irq with integer")
MAINTAINERS
7b637cd52f02 ("MAINTAINERS: fix Microchip CAN BUS Analyzer Tool entry typo")
7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes possible leak of PTP virtual clocks.
The number of PTP virtual clocks to be unregistered is passed as
'u32', but the function that unregister the devices handles that as
'u8'.
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After writing an image blob to the flash memory, a reboot is required
to reload the FPGA. There is no versioning prsent in the FPGA image
file, so only a running version is available. The 'stored version'
was set to 'pending' in order to indicate a reboot was needed.
This isn't reliable, as the module could be unloaded/loaded, losing
the "reboot needed" indicator. Also, the devlink 'stored version'
information is designed to refer to the actual image version.
Unfortunately, there is no method to determine the flash image version
other than booting it, so remove the devlink stored version setting.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TimeCard has two FPGA images in the flash: the actual firmware,
and a manufacturing fallback version which is intended to act as a
loader in case the flash update failed.
Name these "fw" and "loader", which are reflected in devlink:
[root@timecard drv]# devlink dev info
pci/0000:04:00.0:
driver ptp_ocp
serial_number fc:c2:3d:2e:d7:c0
versions:
running:
fw 5
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GPS is not the only available positioning system. Use the generic
naming of "GNSS" instead.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"devlink health" was used as a way to monitor the GNSS signal
status. This isn't really the intended use, and the same
functionality can be achived by monitoring the status file.
Remove the devlink heath support entirely, and also remove the
currently unused devlink parameters.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two PPS blocks: one handles the external PPS signal output,
with the other handling the PPS signal input to the internal clock.
Add controls for the external PPS block.
Rename the fields so they match their function.
Add cable_delay to the register definitions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the put_device() call to the error handling path, so the
device is released after the .release callback, avoiding a
use-after-free.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The OpenCompute timecard driver has additional functionality besides
a clock. Make the following resources available:
- The external timestamp channels (ts0/ts1)
- devlink support for flashing and health reporting
- GPS and MAC serial ports
- board serial number (obtained from i2c device)
Also add watchdog functionality for when GNSS goes into holdover.
The resources are collected under a timecard class directory:
[jlemon@timecard ~]$ ls -g /sys/class/timecard/ocp1/
total 0
-r--r--r--. 1 root 4096 Aug 3 19:49 available_clock_sources
-rw-r--r--. 1 root 4096 Aug 3 19:49 clock_source
lrwxrwxrwx. 1 root 0 Aug 3 19:49 device -> ../../../0000:04:00.0/
-r--r--r--. 1 root 4096 Aug 3 19:49 gps_sync
lrwxrwxrwx. 1 root 0 Aug 3 19:49 i2c -> ../../xiic-i2c.1024/i2c-2/
drwxr-xr-x. 2 root 0 Aug 3 19:49 power/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 pps ->
../../../../../virtual/pps/pps1/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ptp -> ../../ptp/ptp2/
-r--r--r--. 1 root 4096 Aug 3 19:49 serialnum
lrwxrwxrwx. 1 root 0 Aug 3 19:49 subsystem ->
../../../../../../class/timecard/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ttyGPS -> ../../tty/ttyS7/
lrwxrwxrwx. 1 root 0 Aug 3 19:49 ttyMAC -> ../../tty/ttyS8/
-rw-r--r--. 1 root 4096 Aug 3 19:39 uevent
The labeling is needed at the minimum, in order to tell the serial
devices apart.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An earlier commit set the pps_lookup cookie, but the line
was somehow added to the wrong code block. Correct this.
Fixes: 8602e40fc813 ("ptp: Set lookup cookie when creating a PTP PPS source.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix format string mismatch in ptp_sysfs.c. Use %u for unsigned int.
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix NULL pointer dereference in ptp_clock_register. The argument
"parent" of ptp_clock_register may be NULL pointer.
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add kernel API ptp_convert_timestamp() to convert raw hardware timestamp
to a specified ptp vclock time.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add kernel API ptp_get_vclocks_index() to get all ptp
vclocks index on pclock.
This is preparation for supporting ptp vclocks info query
through ethtool.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Track available ptp vclocks information. Record index values
of available ptp vclocks during registering and unregistering.
This is preparation for supporting ptp vclocks info query
through ethtool.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support ptp physical/virtual clocks conversion via sysfs.
There will be a new attribute n_vclocks under ptp physical
clock sysfs.
- In default, the value is 0 meaning only ptp physical clock
is in use.
- Setting the value can create corresponding number of ptp
virtual clocks to use. But current physical clock is guaranteed
to stay free running.
- Setting the value back to 0 can delete virtual clocks and back
use physical clock again.
Another new attribute max_vclocks control the maximum number of
ptp vclocks.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add ptp virtual clock driver framework
utilizing timecounter/cyclecounter.
The patch just exports two essential APIs for PTP driver.
- ptp_vclock_register()
- ptp_vclock_unregister()
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating a PTP device, the configuration block allows
creation of an associated PPS device. However, there isn't
any way to associate the two devices after creation.
Set the PPS cookie, so pps_lookup_dev(ptp) performs correctly.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511cd ("ptp: validate the requested frequency adjustment.")
Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cdc-wdm: s/kill_urbs/poison_urbs/ to fix build
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an error occurs after a successful 'pci_ioremap_bar()' call, it must be
undone by a corresponding 'pci_iounmap()' call, as already done in the
remove function.
Fixes: a7e1abad13f3 ("ptp: Add clock driver for the OpenCompute TimeCard.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make scaled_ppm_to_ppb static inline to be able to build drivers that
use this function even with PTP_1588_CLOCK disabled.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for Linux 5.13
New features:
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
- Alexandru is now a reviewer (not really a new feature...)
Fixes:
- Proper emulation of the GICR_TYPER register
- Handle the complete set of relocation in the nVHE EL2 object
- Get rid of the oprofile dependency in the PMU code (and of the
oprofile body parts at the same time)
- Debug and SPE fixes
- Fix vcpu reset
|
|
Commit 300bb1fe7671 ("ptp: arm/arm64: Enable ptp_kvm for arm/arm64")
enable ptp_kvm support for ARM platforms and for any ARM platform that
does not support this, the following error message is displayed ...
ERR KERN fail to initialize ptp_kvm
For platforms that do not support ptp_kvm this error is a bit misleading
and so fix this by only printing this message if the error returned by
kvm_arch_ptp_init() is not -EOPNOTSUPP. Note that -EOPNOTSUPP is only
returned by ARM platforms today if ptp_kvm is not supported.
Fixes: 300bb1fe7671 ("ptp: arm/arm64: Enable ptp_kvm for arm/arm64")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210420132419.1318148-1-jonathanh@nvidia.com
|
|
Currently, there is no mechanism to keep time sync between guest and host
in arm/arm64 virtualization environment. Time in guest will drift compared
with host after boot up as they may both use third party time sources
to correct their time respectively. The time deviation will be in order
of milliseconds. But in some scenarios,like in cloud environment, we ask
for higher time precision.
kvm ptp clock, which chooses the host clock source as a reference
clock to sync time between guest and host, has been adopted by x86
which takes the time sync order from milliseconds to nanoseconds.
This patch enables kvm ptp clock for arm/arm64 and improves clock sync precision
significantly.
Test result comparisons between with kvm ptp clock and without it in arm/arm64
are as follows. This test derived from the result of command 'chronyc
sources'. we should take more care of the last sample column which shows
the offset between the local clock and the source at the last measurement.
no kvm ptp in guest:
MS Name/IP address Stratum Poll Reach LastRx Last sample
========================================================================
^* dns1.synet.edu.cn 2 6 377 13 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 21 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 29 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 37 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 45 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 53 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 61 +1040us[+1581us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 4 -130us[ +796us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 12 -130us[ +796us] +/- 21ms
^* dns1.synet.edu.cn 2 6 377 20 -130us[ +796us] +/- 21ms
in host:
MS Name/IP address Stratum Poll Reach LastRx Last sample
========================================================================
^* 120.25.115.20 2 7 377 72 -470us[ -603us] +/- 18ms
^* 120.25.115.20 2 7 377 92 -470us[ -603us] +/- 18ms
^* 120.25.115.20 2 7 377 112 -470us[ -603us] +/- 18ms
^* 120.25.115.20 2 7 377 2 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 22 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 43 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 63 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 83 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 103 +872ns[-6808ns] +/- 17ms
^* 120.25.115.20 2 7 377 123 +872ns[-6808ns] +/- 17ms
The dns1.synet.edu.cn is the network reference clock for guest and
120.25.115.20 is the network reference clock for host. we can't get the
clock error between guest and host directly, but a roughly estimated value
will be in order of hundreds of us to ms.
with kvm ptp in guest:
chrony has been disabled in host to remove the disturb by network clock.
MS Name/IP address Stratum Poll Reach LastRx Last sample
========================================================================
* PHC0 0 3 377 8 -7ns[ +1ns] +/- 3ns
* PHC0 0 3 377 8 +1ns[ +16ns] +/- 3ns
* PHC0 0 3 377 6 -4ns[ -0ns] +/- 6ns
* PHC0 0 3 377 6 -8ns[ -12ns] +/- 5ns
* PHC0 0 3 377 5 +2ns[ +4ns] +/- 4ns
* PHC0 0 3 377 13 +2ns[ +4ns] +/- 4ns
* PHC0 0 3 377 12 -4ns[ -6ns] +/- 4ns
* PHC0 0 3 377 11 -8ns[ -11ns] +/- 6ns
* PHC0 0 3 377 10 -14ns[ -20ns] +/- 4ns
* PHC0 0 3 377 8 +4ns[ +5ns] +/- 4ns
The PHC0 is the ptp clock which choose the host clock as its source
clock. So we can see that the clock difference between host and guest
is in order of ns.
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-8-jianyong.wu@arm.com
|
|
Currently, the ptp_kvm module contains a lot of x86-specific code.
Let's move this code into a new arch-specific file in the same directory,
and rename the arch-independent file to ptp_kvm_common.c.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-4-jianyong.wu@arm.com
|