| Age | Commit message (Collapse) | Author |
|---|
|
commit 84961f28e9d1 ("[SCSI] Don't add scsi_device for devices that return
PQ=1, PDT=0x1f") returns SCSI_SCAN_TARGET_PRESENT if inquiry returns PQ=1,
and PDT = 0x1f. However, from the scsi spec, it seemed setting PQ=1, and
PDT to the type it is capable to support, can also mean the device is not
connected. E.g. we see an IBM/2145 returns PQ=1 and PDT=0 for a non-mapped
lun (details attached at the end).
This patch changes the check condition a bit, so the check don't require
PTD to be 0x1f when PQ=1.
$ echo 0 0 1 > /sys/class/scsi_host/host1/scan
[ 2483.722186] scsi 1:0:0:1: scsi scan: INQUIRY pass 1 length 36
[ 2483.725687] scsi 1:0:0:1: scsi scan: INQUIRY successful with code 0x0
[ 2483.729171] scsi 1:0:0:1: scsi scan: INQUIRY pass 2 length 109
[ 2483.732481] scsi 1:0:0:1: scsi scan: INQUIRY successful with code 0x0
[ 2483.735911] scsi 1:0:0:1: Direct-Access IBM 2145 0000 PQ: 1 ANSI: 6
[ 2483.741282] scsi 1:0:0:1: Attached scsi generic sg2 type 0
$ tail /proc/scsi/scsi
Attached devices:
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: IBM Model: 2145 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 06
$ lsscsi
[0:0:0:0] disk IBM 2145 0000 /dev/sdb
[1:0:0:0] disk IBM 2145 0000 /dev/sda
[1:0:0:1] disk IBM 2145 0000 -
Signed-off-by: Li Zhong <lizhongfs@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
scsi_alloc_sdev()
scsi_probe_and_add_lun()
scsi_sequential_lun_scan()
__scsi_scan_target()
scsi_scan_target()
mutex_lock()
scsi_scan_channel()
scsi_scan_host_selected()
mutex_lock()
scsi_report_lun_scan()
__scsi_scan_target()
...
__scsi_add_device()
mutex_lock()
__scsi_scan_target()
...
scsi_report_lun_scan()
...
scsi_get_host_dev()
mutex_lock()
scsi_probe_and_add_lun()
...
scsi_add_lun()
scsi_probe_and_add_lun()
...
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This removes the legacy (non-mq) IO path for SCSI.
Cc: linux-scsi@vger.kernel.org
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When evaluating a SCSI command's result using the field access macros,
check for equality of the fields and not if a specific bit is set.
This is a preparation patch, for reworking the results field in the
SCSI command.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the type blist_flags_t for all variables that represent blacklist
flags. Additionally, suppress recently introduced sparse warnings
related to blacklist flags.
[mkp: fixed commit id]
Fixes: 5ebde4694e3b ("scsi: Use 'blist_flags_t' for scsi_devinfo flags")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As per recommendation from Linus we should be using a distinct type for
blacklist flags.
[mkp: was cut against an older kernel, applied by hand]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each scsi device is scanned according to the found blacklist flags, but
this information is never presented to sysfs. This makes it quite hard
to figure out if blacklisting worked as expected. With this patch we're
exporting an additional attribute 'blacklist' containing the blacklist
flags for this device.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SBC-4 states:
"A MAXIMUM UNMAP LBA COUNT field set to a non-zero value indicates the
maximum number of LBAs that may be unmapped by an UNMAP command"
"A MAXIMUM WRITE SAME LENGTH field set to a non-zero value indicates
the maximum number of contiguous logical blocks that the device server
allows to be unmapped or written in a single WRITE SAME command."
Despite the spec being clear on the topic, some devices incorrectly
expect WRITE SAME commands with the UNMAP bit set to be limited to the
value reported in MAXIMUM UNMAP LBA COUNT in the Block Limits VPD.
Implement a blacklist option that can be used to accommodate devices
with this behavior.
Cc: <stable@vger.kernel.org>
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename several functions to make it easy to see which queue type a
function is intended for.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, bnx2fc,
qedf, hpsa, hisi_sas, smartpqi, cxlflash, aacraid, csiostor along with
a host of minor and miscellaneous changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (276 commits)
qla2xxx: Fix NVMe entry_type for iocb packet on BE system
scsi: qla2xxx: avoid unused-function warning
scsi: snic: fix a couple of spelling mistakes/typos
scsi: qla2xxx: fix a bunch of typos and spelling mistakes
scsi: lpfc: don't double count abort errors
scsi: lpfc: spin_lock_irq() is not nestable
scsi: hisi_sas: optimise DMA slot memory
scsi: ibmvfc: constify dev_pm_ops structures.
scsi: ibmvscsi: constify dev_pm_ops structures.
scsi: cxlflash: Update debug prints in reset handlers
scsi: cxlflash: Update send_tmf() parameters
scsi: cxlflash: Avoid double free of character device
scsi: Add STARGET_CREATED_REMOVE state to scsi_target_state
scsi: ses: do not add a device to an enclosure if enclosure_add_links() fails.
scsi: ufs: flush eh_work when eh_work scheduled.
scsi: qla2xxx: Protect access to qpair members with qpair->qp_lock
scsi: sun_esp: fix device reference leaks
scsi: fnic: changing queue command to return result DID_IMM_RETRY when rport is init
scsi: fnic: correct speed display and add support for 25,40 and 100G
scsi: fnic: added timestamp reporting in fnic debug stats
...
|
|
The addition of the STARGET_REMOVE state had the side effect of
introducing a race condition that can cause a crash.
scsi_target_reap_ref_release() checks the starget->state to
see if it still in STARGET_CREATED, and if so, skips calling
transport_remove_device() and device_del(), because the starget->state
is only set to STARGET_RUNNING after scsi_target_add() has called
device_add() and transport_add_device().
However, if an rport loss occurs while a target is being scanned,
it can happen that scsi_remove_target() will be called while the
starget is still in the STARGET_CREATED state. In this case, the
starget->state will be set to STARGET_REMOVE, and as a result,
scsi_target_reap_ref_release() will take the wrong path. The end
result is a panic:
[ 1255.356653] Oops: 0000 [#1] SMP
[ 1255.360154] Modules linked in: x86_pkg_temp_thermal kvm_intel kvm irqbypass crc32c_intel ghash_clmulni_i
[ 1255.393234] CPU: 5 PID: 149 Comm: kworker/u96:4 Tainted: G W 4.11.0+ #8
[ 1255.401879] Hardware name: Dell Inc. PowerEdge R320/08VT7V, BIOS 2.0.22 11/19/2013
[ 1255.410327] Workqueue: scsi_wq_6 fc_scsi_scan_rport [scsi_transport_fc]
[ 1255.417720] task: ffff88060ca8c8c0 task.stack: ffffc900048a8000
[ 1255.424331] RIP: 0010:kernfs_find_ns+0x13/0xc0
[ 1255.429287] RSP: 0018:ffffc900048abbf0 EFLAGS: 00010246
[ 1255.435123] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 1255.443083] RDX: 0000000000000000 RSI: ffffffff8188d659 RDI: 0000000000000000
[ 1255.451043] RBP: ffffc900048abc10 R08: 0000000000000000 R09: 0000012433fe0025
[ 1255.459005] R10: 0000000025e5a4b5 R11: 0000000025e5a4b5 R12: ffffffff8188d659
[ 1255.466972] R13: 0000000000000000 R14: ffff8805f55e5088 R15: 0000000000000000
[ 1255.474931] FS: 0000000000000000(0000) GS:ffff880616b40000(0000) knlGS:0000000000000000
[ 1255.483959] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1255.490370] CR2: 0000000000000068 CR3: 0000000001c09000 CR4: 00000000000406e0
[ 1255.498332] Call Trace:
[ 1255.501058] kernfs_find_and_get_ns+0x31/0x60
[ 1255.505916] sysfs_unmerge_group+0x1d/0x60
[ 1255.510498] dpm_sysfs_remove+0x22/0x60
[ 1255.514783] device_del+0xf4/0x2e0
[ 1255.518577] ? device_remove_file+0x19/0x20
[ 1255.523241] attribute_container_class_device_del+0x1a/0x20
[ 1255.529457] transport_remove_classdev+0x4e/0x60
[ 1255.534607] ? transport_add_class_device+0x40/0x40
[ 1255.540046] attribute_container_device_trigger+0xb0/0xc0
[ 1255.546069] transport_remove_device+0x15/0x20
[ 1255.551025] scsi_target_reap_ref_release+0x25/0x40
[ 1255.556467] scsi_target_reap+0x2e/0x40
[ 1255.560744] __scsi_scan_target+0xaa/0x5b0
[ 1255.565312] scsi_scan_target+0xec/0x100
[ 1255.569689] fc_scsi_scan_rport+0xb1/0xc0 [scsi_transport_fc]
[ 1255.576099] process_one_work+0x14b/0x390
[ 1255.580569] worker_thread+0x4b/0x390
[ 1255.584651] kthread+0x109/0x140
[ 1255.588251] ? rescuer_thread+0x330/0x330
[ 1255.592730] ? kthread_park+0x60/0x60
[ 1255.596815] ret_from_fork+0x29/0x40
[ 1255.600801] Code: 24 08 48 83 42 40 01 5b 41 5c 5d c3 66 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90
[ 1255.621876] RIP: kernfs_find_ns+0x13/0xc0 RSP: ffffc900048abbf0
[ 1255.628479] CR2: 0000000000000068
[ 1255.632756] ---[ end trace 34a69ba0477d036f ]---
Fix this by adding another scsi_target state STARGET_CREATED_REMOVE
to distinguish this case.
Fixes: f05795d3d771 ("scsi: Add intermediate STARGET_REMOVE state to scsi_target_state")
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Serializing SCSI device state changes avoids that two state changes can
occur concurrently, e.g. the state changes in scsi_target_block() and
__scsi_remove_device(). This serialization is essential to make patch
"Make __scsi_remove_device go straight from BLOCKED to DEL" work
reliably.
Enable this mechanism for all scsi_target_*block() callers but not for
the scsi_internal_device_unblock() calls from the mpt3sas driver because
that driver can call scsi_internal_device_unblock() from atomic context.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sphinx is very pedantic with regards to ident/spacing.
Fix some kernel-doc markups in order to solve those
errors/warnings:
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsicam.c:121: WARNING: Inline emphasis start-string without end-string.
./drivers/scsi/scsi_scan.c:1056: ERROR: Unexpected indentation.
./drivers/scsi/scsi_scan.c:1057: WARNING: Block quote ends without a blank line; unexpected unindent.
./drivers/scsi/scsi_transport_fc.c:2918: ERROR: Unexpected indentation.
./drivers/scsi/scsi_transport_fc.c:2921: WARNING: Block quote ends without a blank line; unexpected unindent.
./drivers/scsi/scsi_transport_fc.c:2922: WARNING: Enumerated list ends without a blank line; unexpected unindent.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The local variable of 'devname' in scsi_report_lun_scan() isn't used any
more, so remove it.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes one use-after-free report[1] by KASAN.
In __scsi_scan_target(), when a type 31 device is probed,
SCSI_SCAN_TARGET_PRESENT is returned and the target will be scanned
again.
Inside the following scsi_report_lun_scan(), one new scsi_device
instance is allocated, and scsi_probe_and_add_lun() is called again to
probe the target and still see type 31 device, finally
__scsi_remove_device() is called to remove & free the device at the end
of scsi_probe_and_add_lun(), so cause use-after-free in
scsi_report_lun_scan().
And the following SCSI log can be observed:
scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36
scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0
scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added
scsi 0:0:2:0: scsi scan: Sending REPORT LUNS to (try 0)
scsi 0:0:2:0: scsi scan: REPORT LUNS successful (try 0) result 0x0
scsi 0:0:2:0: scsi scan: REPORT LUN scan
scsi 0:0:2:0: scsi scan: INQUIRY pass 1 length 36
scsi 0:0:2:0: scsi scan: INQUIRY successful with code 0x0
scsi 0:0:2:0: scsi scan: peripheral device type of 31, no device added
BUG: KASAN: use-after-free in __scsi_scan_target+0xbf8/0xe40 at addr ffff88007b44a104
This patch fixes the issue by moving the putting reference at
the end of scsi_report_lun_scan().
[1] KASAN report
==================================================================
[ 3.274597] PM: Adding info for serio:serio1
[ 3.275127] BUG: KASAN: use-after-free in __scsi_scan_target+0xd87/0xdf0 at addr ffff880254d8c304
[ 3.275653] Read of size 4 by task kworker/u10:0/27
[ 3.275903] CPU: 3 PID: 27 Comm: kworker/u10:0 Not tainted 4.8.0 #2121
[ 3.276258] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3.276797] Workqueue: events_unbound async_run_entry_fn
[ 3.277083] ffff880254d8c380 ffff880259a37870 ffffffff94bbc6c1 ffff880078402d80
[ 3.277532] ffff880254d8bb80 ffff880259a37898 ffffffff9459fec1 ffff880259a37930
[ 3.277989] ffff880254d8bb80 ffff880078402d80 ffff880259a37920 ffffffff945a0165
[ 3.278436] Call Trace:
[ 3.278528] [<ffffffff94bbc6c1>] dump_stack+0x65/0x84
[ 3.278797] [<ffffffff9459fec1>] kasan_object_err+0x21/0x70
[ 3.279063] device: 'psaux': device_add
[ 3.279616] [<ffffffff945a0165>] kasan_report_error+0x205/0x500
[ 3.279651] PM: Adding info for No Bus:psaux
[ 3.280202] [<ffffffff944ecd22>] ? kfree_const+0x22/0x30
[ 3.280486] [<ffffffff94bc2dc9>] ? kobject_release+0x119/0x370
[ 3.280805] [<ffffffff945a0543>] __asan_report_load4_noabort+0x43/0x50
[ 3.281170] [<ffffffff9507e1f7>] ? __scsi_scan_target+0xd87/0xdf0
[ 3.281506] [<ffffffff9507e1f7>] __scsi_scan_target+0xd87/0xdf0
[ 3.281848] [<ffffffff9507d470>] ? scsi_add_device+0x30/0x30
[ 3.282156] [<ffffffff94f7f660>] ? pm_runtime_autosuspend_expiration+0x60/0x60
[ 3.282570] [<ffffffff956ddb07>] ? _raw_spin_lock+0x17/0x40
[ 3.282880] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160
[ 3.283200] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0
[ 3.283563] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250
[ 3.283882] [<ffffffff9507efc1>] do_scan_async+0x41/0x450
[ 3.284173] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610
[ 3.284492] [<ffffffff941a8954>] ? pwq_dec_nr_in_flight+0x124/0x2a0
[ 3.284876] [<ffffffff941d1770>] ? preempt_count_add+0x130/0x160
[ 3.285207] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0
[ 3.285526] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0
[ 3.285844] [<ffffffff941aa810>] ? process_one_work+0x12d0/0x12d0
[ 3.286182] [<ffffffff941bb365>] kthread+0x1c5/0x260
[ 3.286443] [<ffffffff940855cd>] ? __switch_to+0x88d/0x1430
[ 3.286745] [<ffffffff941bb1a0>] ? kthread_worker_fn+0x5a0/0x5a0
[ 3.287085] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40
[ 3.287368] [<ffffffff941bb1a0>] ? kthread_worker_fn+0x5a0/0x5a0
[ 3.287697] Object at ffff880254d8bb80, in cache kmalloc-2048 size: 2048
[ 3.288064] Allocated:
[ 3.288147] PID = 27
[ 3.288218] [<ffffffff940b27ab>] save_stack_trace+0x2b/0x50
[ 3.288531] [<ffffffff9459f246>] save_stack+0x46/0xd0
[ 3.288806] [<ffffffff9459f4bd>] kasan_kmalloc+0xad/0xe0
[ 3.289098] [<ffffffff9459c07e>] __kmalloc+0x13e/0x250
[ 3.289378] [<ffffffff95078e5a>] scsi_alloc_sdev+0xea/0xcf0
[ 3.289701] [<ffffffff9507de76>] __scsi_scan_target+0xa06/0xdf0
[ 3.290034] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160
[ 3.290362] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0
[ 3.290724] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250
[ 3.291055] [<ffffffff9507efc1>] do_scan_async+0x41/0x450
[ 3.291354] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610
[ 3.291695] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0
[ 3.292022] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0
[ 3.292325] [<ffffffff941bb365>] kthread+0x1c5/0x260
[ 3.292594] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40
[ 3.292886] Freed:
[ 3.292945] PID = 27
[ 3.293016] [<ffffffff940b27ab>] save_stack_trace+0x2b/0x50
[ 3.293327] [<ffffffff9459f246>] save_stack+0x46/0xd0
[ 3.293600] [<ffffffff9459fa61>] kasan_slab_free+0x71/0xb0
[ 3.293916] [<ffffffff9459bac2>] kfree+0xa2/0x1f0
[ 3.294168] [<ffffffff9508158a>] scsi_device_dev_release_usercontext+0x50a/0x730
[ 3.294598] [<ffffffff941ace9a>] execute_in_process_context+0xda/0x130
[ 3.294974] [<ffffffff9508107c>] scsi_device_dev_release+0x1c/0x20
[ 3.295322] [<ffffffff94f566f6>] device_release+0x76/0x1e0
[ 3.295626] [<ffffffff94bc2db7>] kobject_release+0x107/0x370
[ 3.295942] [<ffffffff94bc29ce>] kobject_put+0x4e/0xa0
[ 3.296222] [<ffffffff94f56e17>] put_device+0x17/0x20
[ 3.296497] [<ffffffff9505201c>] scsi_device_put+0x7c/0xa0
[ 3.296801] [<ffffffff9507e1bc>] __scsi_scan_target+0xd4c/0xdf0
[ 3.297132] [<ffffffff9507e505>] scsi_scan_channel+0x105/0x160
[ 3.297458] [<ffffffff9507e8a2>] scsi_scan_host_selected+0x212/0x2f0
[ 3.297829] [<ffffffff9507eb3c>] do_scsi_scan_host+0x1bc/0x250
[ 3.298156] [<ffffffff9507efc1>] do_scan_async+0x41/0x450
[ 3.298453] [<ffffffff941c1fee>] async_run_entry_fn+0xfe/0x610
[ 3.298777] [<ffffffff941a9a84>] process_one_work+0x544/0x12d0
[ 3.299105] [<ffffffff941aa8e9>] worker_thread+0xd9/0x12f0
[ 3.299408] [<ffffffff941bb365>] kthread+0x1c5/0x260
[ 3.299676] [<ffffffff956dde9f>] ret_from_fork+0x1f/0x40
[ 3.299967] Memory state around the buggy address:
[ 3.300209] ffff880254d8c200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 3.300608] ffff880254d8c280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 3.300986] >ffff880254d8c300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 3.301408] ^
[ 3.301550] ffff880254d8c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 3.301987] ffff880254d8c400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 3.302396]
==================================================================
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We get 2 warnings about global functions without a declaration in the
scsi driver when building with W=1:
drivers/scsi/scsi_lib.c:467:6: warning: no previous prototype for 'scsi_requeue_run_queue' [-Wmissing-prototypes]
drivers/scsi/scsi_lib.c:2609:6: warning: no previous prototype for 'scsi_evt_thread' [-Wmissing-prototypes]
In fact, both functions are declared in drivers/scsi/scsi_scan.c but
need to move them into scsi_priv.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795d3 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
40998193560d ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 40998193560dab6c3ce8d25f4fa58a23e252ef38
Cc: stable@vger.kernel.org
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On larger installations it is useful to disable automatic LUN scanning,
and only add the required LUNs via udev rules. This can speed up bootup
dramatically.
This patch introduces a new scan module parameter value 'manual', which
works like 'none', but can be overridden by setting the 'rescan' value
from scsi_scan_target to 'SCSI_SCAN_MANUAL'. And it updates all
relevant callers to set the 'rescan' value to 'SCSI_SCAN_MANUAL' if
invoked via the 'scan' option in sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If a device needs to be rescanned the device_handler might need
to be rechecked, too.
So add a 'rescan' callback to the device handler and call it
upon scsi_rescan_device(). The rescan callback will be invoked
from the Unit Attention handling of ASC/ASCQ 3F 03
(INQUIRY DATA HAS CHANGED).
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new blacklist flag BLIST_SYNC_ALUA to instruct the
alua device handler to use synchronous command submission
for ALUA commands.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The hpsa driver uses this function to cleanup inquiry data. Our new pqi
driver will also use this function. This function was copied into both
drivers.
This patch exports sanitize_inquiry_string so the hpsa and the pqi
drivers can use this function directly.
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
|
|
The VPD page information might change, so we need to be able to update
it. This patch implements a VPD page rescan whenever the 'rescan' sysfs
attribute is triggered.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some host adapters (e.g. Hyper-V storvsc) are known for not respecting
the SPC-2/3/4 requirement for 'INQUIRY data (see table ...) shall
contain at least 36 bytes'. As a result we get tons on 'scsi 0:7:1:1:
scsi scan: INQUIRY result too short (5), using 36' messages on
console. This can be problematic for slow consoles. Introduce
short_inquiry flag in struct Scsi_Host to print the message once per
host.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SCSI queue for 4.4.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The only user of scsi_prep_async_scan() is scsi_scan_host() and it
handles the situation correctly. Move 'called twice' reporting to debug
level as well.
The issue is observed on Hyper-V: on any device add/remove event storvsc
driver calls scsi_scan_host() and in case previous scan is still running
we get the message and stack dump on console.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This patch fixes an issue seen with an IBM 2145 (SVC) where, following an error
injection test which results in paths going offline, when they came
back online, the path would timeout the REPORT_LUNS issued during the
scan. This timeout situation continued until retries were expired, resulting in
falling back to a sequential LUN scan. Then, since the target responds
with PQ=1, PDT=0 for all possible LUNs, due to the way the sequential
LUN scan code works, we end up adding 512 LUNs for each target, when there
is really only a small handful of LUNs that are actually present.
This patch increases the timeout used on the REPORT_LUNS to 30 seconds.
This patch solves the issue of 512 non existent LUNs showing up after
this event.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the functions that are used by both the initiator and target
subsystems into scsi_common.c/.h. This change will allow to remove
the initiator SCSI header include directives from most SCSI target
source files in a later patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Currently we blindly use the value of cmd_per_lun as the initial setting for
queue_depth. This fails miserably (hangs the system) if it is zero, which is
the default value for anything uninitialised in the template. The net result
is that every host template has to set a value for cmd_per_lun. Instead, use
a default value of 1 if the actual value is unset. This should pave the way
for removing cmd_per_lun from all the templates and eventually from SCSI
itself.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This works around a issue with qnap iscsi targets not handling large IOs
very well.
The target returns:
VPD INQUIRY: Block limits page (SBC)
Maximum compare and write length: 1 blocks
Optimal transfer length granularity: 1 blocks
Maximum transfer length: 4294967295 blocks
Optimal transfer length: 4294967295 blocks
Maximum prefetch, xdread, xdwrite transfer length: 0 blocks
Maximum unmap LBA count: 8388607
Maximum unmap block descriptor count: 1
Optimal unmap granularity: 16383
Unmap granularity alignment valid: 0
Unmap granularity alignment: 0
Maximum write same length: 0xffffffff blocks
Maximum atomic transfer length: 0
Atomic alignment: 0
Atomic transfer length granularity: 0
and it is *sometimes* able to handle at least one IO of size up to 8 MB. We
have seen in traces where it will sometimes work, but other times it
looks like it fails and it looks like it returns failures if we send
multiple large IOs sometimes. Also it looks like it can return 2 different
errors. It will sometimes send iscsi reject errors indicating out of
resources or it will send invalid cdb illegal requests check conditions.
And then when it sends iscsi rejects it does not seem to handle retries
when there are command sequence holes, so I could not just add code to
try and gracefully handle that error code.
The problem is that we do not have a good contact for the company,
so we are not able to determine under what conditions it returns
which error and why it sometimes works.
So, this patch just adds a new black list flag to set targets like this to
the old max safe sectors of 1024. The max_hw_sectors changes added in 3.19
caused this regression, so I also ccing stable.
Reported-by: Christian Hesse <list@eworm.de>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Lock the device embedded in the scsi_device to protect against
concurrent calls to ->remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull core block IO changes from Jens Axboe:
"This contains:
- A series from Christoph that cleans up and refactors various parts
of the REQ_BLOCK_PC handling. Contributions in that series from
Dongsu Park and Kent Overstreet as well.
- CFQ:
- A bug fix for cfq for realtime IO scheduling from Jeff Moyer.
- A stable patch fixing a potential crash in CFQ in OOM
situations. From Konstantin Khlebnikov.
- blk-mq:
- Add support for tag allocation policies, from Shaohua. This is
a prep patch enabling libata (and other SCSI parts) to use the
blk-mq tagging, instead of rolling their own.
- Various little tweaks from Keith and Mike, in preparation for
DM blk-mq support.
- Minor little fixes or tweaks from me.
- A double free error fix from Tony Battersby.
- The partition 4k issue fixes from Matthew and Boaz.
- Add support for zero+unprovision for blkdev_issue_zeroout() from
Martin"
* 'for-3.20/core' of git://git.kernel.dk/linux-block: (27 commits)
block: remove unused function blk_bio_map_sg
block: handle the null_mapped flag correctly in blk_rq_map_user_iov
blk-mq: fix double-free in error path
block: prevent request-to-request merging with gaps if not allowed
blk-mq: make blk_mq_run_queues() static
dm: fix multipath regression due to initializing wrong request
cfq-iosched: handle failure of cfq group allocation
block: Quiesce zeroout wrapper
block: rewrite and split __bio_copy_iov()
block: merge __bio_map_user_iov into bio_map_user_iov
block: merge __bio_map_kern into bio_map_kern
block: pass iov_iter to the BLOCK_PC mapping functions
block: add a helper to free bio bounce buffer pages
block: use blk_rq_map_user_iov to implement blk_rq_map_user
block: simplify bio_map_kern
block: mark blk-mq devices as stackable
block: keep established cmd_flags when cloning into a blk-mq request
block: add blk-mq support to blk_insert_cloned_request()
block: require blk_rq_prep_clone() be given an initialized clone request
blk-mq: add tag allocation policy
...
|
|
The libata tag allocation is using a round-robin policy. Next patch will
make libata use block generic tag allocation, so let's add a policy to
tag allocation.
Currently two policies: FIFO (default) and round-robin.
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Update scsi_report_lun_scan to initially always report up to 511 LUs,
as the previous default max_report_luns did. Retry in a loop if not
enough memory is available for the number of LUs reported. Parameter
max_report_luns is removed as it is no longer used.
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The driver core driver structure has grown an owner field and now
requires it to be set for all modular drivers. Set it up for
all scsi_driver instances and get rid of the now superflous
scsi_driver owner field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Shane M Seymour <shane.seymour@hp.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
The Scsi_Host structure max_lun field is the maximum allowed LUN plus 1. So
a LUN value is invalid if >= max_lun.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If LLD has added scsi device (by calling scsi_add_device) before scheduling
async scsi_scan_host then scsi_finish_async_scan() will end up calling
scsi_sysfs_add_sdev for scsi device which was already added by LLD.
This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev()
if it's already visible to rest of the kernel.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some devices may respond with wrong type for well-known logical units.
This patch forces well-known type for devices which doesn't report it
correct.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
