| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
|
|
We need the USB changes in here for additional patches to be able to
apply cleanly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'arm/omap', 'arm/smmu', 'x86/vt-d', 'x86/amd' and 'core' into next
|
|
r8a66597_endpoint_disable()
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8a5 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the dev->iommu_group check with a proper function
call that better reprensents its purpose.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
refactoring, no functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
detected
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.
Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.
[1] ade2e3a xhci: handle transfer events without TRB pointer
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d602 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6d4 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d602 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dma_pool_destroy() can handle NULL pointer correctly, so there is
no need to check NULL pointer before calling dma_pool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
|
|
The generic power-domain framework has been updated to allow devices
that require more than one power-domain to create a new device for
each power-domain required and then link these new power-domain
devices to the consumer device.
Update the Tegra xHCI driver to use the new APIs provided by the
generic power-domain framework so we can use the generic power-domain
framework for managing the xHCI controllers power-domains. Please
note that to maintain backward compatibility with older device-tree
blobs these new generic power-domain APIs are only used if the
'power-domains' property is present and otherwise we fall back to
using the legacy Tegra APIs for managing the power-domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the XUSB power domains used by the Tegra xHCI controller are
never powered off on the removal of the driver, however, they will be
powered off on probe failure. Update the removal code to be consistent
with the probe failure path to power off the XUSB power domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.
devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.
This fixes the following errors on boards where atmel,oc is not set in
device tree:
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Give USB3 devices a better chance to enumerate at USB3 speeds if
they are connected to a suspended host.
Porting from "671ffdff5b13 xhci: resume USB 3 roothub first"
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The XUSB firmware header is in little endian byte order, so make the
fields __le32 and __le16 instead of u32 and u16 to avoid warnings from
sparse when the fields are used with the endian-aware __le32_to_cpu()
and __le16_to_cpu() accessors, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry
A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.
Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub
Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.
For more details on Soft retry see xhci specs 4.6.8.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Supports SSP scheduling only for SSP device directly connected
to root hub but not through external USB3 gen2 hub which need
use a new scheduling way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Supports LowSpeed and FullSpeed INT/ISOC bandwidth scheduling
with USB multi-TT
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mainly improve SuperSpeed ISOC bandwidth in last microframe,
and LowSpeed/FullSpeed IN INT/ISOC bandwidth in split and
idle microframes by introduing a bandwidth budget table;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make use of maximum ESIT payload of endpoint context to calculate
the number of packets to send in each ESIT
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's dangerous to use empty code define.
Furthermore it lead to the following warning:
"suggest braces around empty body in an « else » statement"
So let's replace emptyness by "do {} while(0)"
Furthermore, as suggested by Joe Perches, rename the macro to INCR.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is code in the .remove() hook to handle the drvdata
being NULL, for good reasons: it is never set, so it will
always be NULL. As I moved code around, static checkers
start complaining.
Instead of this, make sure to always set it on successful
probe so we can always dereference it on the remove path.
Use the platform_device_[set|get]_drvdata() since this is
a platform device.
Fixes: ffa8a31b5b3b ("usb: host: fotg2: add silicon clock handling")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
