| Age | Commit message (Collapse) | Author |
|---|
|
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
|
|
The Octeon OHCI is now supported by the ohci-platform driver, and
USB_OCTEON_OHCI is marked as deprecated. However, it is currently
still necessary to enable it in order to select
USB_OHCI_BIG_ENDIAN_MMIO. Make CPU_CAVIUM_OCTEON select that as well,
so that USB_OCTEON_OHCI is really obsolete.
The old ohci-octeon and ehci-octeon drivers also only enabled big-endian
MMIO in case the CPU was big-endian. Make the selections of
USB_EHCI_BIG_ENDIAN_MMIO and USB_OHCI_BIG_ENDIAN_MMIO conditional, to
match this.
Fixes: 2193dda5eec6 ("USB: host: Remove ehci-octeon and ohci-octeon drivers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Cc: Paul Martin <paul.martin@codethink.co.uk>
Patchwork: https://patchwork.linux-mips.org/patch/10178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of manually handling the frees use devm. There was also a free
missing in the unregister call which is not needed with devm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes bcma_hcd_create_pdev() not return NULL, but a prober
error code in case of an error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fix compilation error in fsl ehci drv because ehci_reset()
and ehci_adjust_port_wakeup_flags() were not exported, and
are used when PM is enabled
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for USB controller version-2.5 used in
T4240 rev2.0, T1024, T1040, T2080, LS1021A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check IP version 2.4 for multi port host USB controller and
return FSL_USB_VER_2_4 macro
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The comment stating that xhci_setup_device() is protected by the address
mutex is not true since
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
as xhci handles two buses.
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the xhci driver from bluntly setting the transferred length to 0 if
we get a STALL on anything else than the data stage of a control transfer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We used to write the root port state changes in turn for every port,
sleeping 20ms after every port state change. Suspended usb2 ports need
two state changes, taking minimun 40ms per port.
Now instead poll the Port Link State Change (PLC) bit as
the state change to U0 will set this bit.
Suspended usb2 ports still need the extra 20ms delay, but we now change
all the port states at once so we only need to sleep 20ms once all together
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the OTG case, the controller might not yet have been
added or is removed before the system suspends.
Assign xhci->main_hcd during probe to prevent NULL
pointer de-reference in xhci_suspend/resume().
Use the hcd->state flag to check if HCD is halted
and if that is so do nothing for xhci_suspend/resume().
[Only for xhci-plat devices, pci devices need it in gen_setup -Mathias]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.
I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.
The following lockup was detected while testing the otg state
machine.
[ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.245358] usb usb1: Product: xHCI Host Controller
[ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 178.267014] hub 1-0:1.0: USB hub found
[ 178.272108] hub 1-0:1.0: 1 port detected
[ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.308776] usb usb2: Product: xHCI Host Controller
[ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 178.329061] hub 2-0:1.0: USB hub found
[ 178.333126] hub 2-0:1.0: 1 port detected
[ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 178.578064] usb usb2: USB disconnect, device number 1
[ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 178.597924] usb usb1: USB disconnect, device number 1
[ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000
[ 190.625120] Workqueue: usb_otg usb_otg_work
[ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.739898] 5 locks held by kworker/u4:0/6:
[ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000
[ 190.814457] Workqueue: usb_hub_wq hub_event
[ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.902650] 5 locks held by kworker/1:0/14:
[ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't set xhci->shared_hcd to NULL in xhci_stop() as we have
still not de-allocated it. It was resulting in a NULL pointer
de-reference if usb_add/remove_hcd() is called repeatedly.
We want repeated add/remove to work for the OTG use case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As xhci_hcd is now allocated by usb_create_hcd(), we don't
need to add the primary HCD before creating the shared HCD.
Creating the shared HCD before adding the primary HCD is particularly
useful for the OTG use case so that we know at the OTG core if
the HCD is in single configuration or dual (primary + shared)
configuration.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Mathias: rearranged to fit on top of the Marvell Armada 385 phy changes]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.
Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some EHCI controllers have a Transaction Translator built into
the root hub. Support this feature in device tree when using
the ehci-platform driver by adding a feature flag for it.
This is needed to get USB working on NXP LPC18xx/43xx platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make Freescale EHCI driver an independent entity from ehci-hcd.c.
This involves
- using module_init/module_exit functions
- using overrides structure
- some necessary code cleanup
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Getting phys by index instead of phy names so that we do
not have to create a naming scheme when multiple phys are present
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Getting phys by index instead of phy names so that we do
not have to create a naming scheme when multiple phys
are present
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Petr Mladek <pmladek@suse.cz>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Our event ring consists of only one segment, and we risk filling
the event ring in case we get isoc transfers with short intervals
such as webcams that fill a TD every microframe (125us)
With 64 TRB segment size one usb camera could fill the event ring in 8ms.
A setup with several cameras and other devices can fill up the
event ring as it is shared between all devices.
This has occurred when uvcvideo queues 5 * 32TD URBs which then
get cancelled when the video mode changes. The cancelled URBs are returned
in the xhci interrupt context and blocks the interrupt handler from
handling the new events.
A full event ring will block xhci from scheduling traffic and affect all
devices conneted to the xhci, will see errors such as Missed Service
Intervals for isoc devices, and and Split transaction errors for LS/FS
interrupt devices.
Increasing the TRB_PER_SEGMENT will also increase the default endpoint ring
size, which is welcome as for most isoc transfer we had to dynamically
expand the endpoint ring anyway to be able to queue the 5 * 32TDs uvcvideo
queues.
The default size used to be 64 TRBs per segment
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB PCI quirks code gets built into the kernel whenever CONFIG_PCI
is enabled, even if CONFIG_USB is not set. This can cause unnecessary
messages to show up in the kernel log, such as "CONFIG_USB_XHCI_HCD is
turned off, defaulting to EHCI" (which makes no sense when the kernel
has been configured without host-side USB support).
This patch addresses the problem by building pci-quirks.o only when
CONFIG_PCI and CONFIG_USB are both enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 70843f623b58 ("usb: host: ehci-msm: Use
devm_ioremap_resource instead of devm_ioremap") and commit
e507bf577e5a ("host: ehci-msm: remove duplicate check on resource"),
because msm_otg and this driver are using same address space to
access AHB mode and USB command registers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Some clean ups and small fixes, but the biggest change is the addition
of the TRACE_DEFINE_ENUM() macro that can be used by tracepoints.
Tracepoints have helper functions for the TP_printk() called
__print_symbolic() and __print_flags() that lets a numeric number be
displayed as a a human comprehensible text. What is placed in the
TP_printk() is also shown in the tracepoint format file such that user
space tools like perf and trace-cmd can parse the binary data and
express the values too. Unfortunately, the way the TRACE_EVENT()
macro works, anything placed in the TP_printk() will be shown pretty
much exactly as is. The problem arises when enums are used. That's
because unlike macros, enums will not be changed into their values by
the C pre-processor. Thus, the enum string is exported to the format
file, and this makes it useless for user space tools.
The TRACE_DEFINE_ENUM() solves this by converting the enum strings in
the TP_printk() format into their number, and that is what is shown to
user space. For example, the tracepoint tlb_flush currently has this
in its format file:
__print_symbolic(REC->reason,
{ TLB_FLUSH_ON_TASK_SWITCH, "flush on task switch" },
{ TLB_REMOTE_SHOOTDOWN, "remote shootdown" },
{ TLB_LOCAL_SHOOTDOWN, "local shootdown" },
{ TLB_LOCAL_MM_SHOOTDOWN, "local mm shootdown" })
After adding:
TRACE_DEFINE_ENUM(TLB_FLUSH_ON_TASK_SWITCH);
TRACE_DEFINE_ENUM(TLB_REMOTE_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_SHOOTDOWN);
TRACE_DEFINE_ENUM(TLB_LOCAL_MM_SHOOTDOWN);
Its format file will contain this:
__print_symbolic(REC->reason,
{ 0, "flush on task switch" },
{ 1, "remote shootdown" },
{ 2, "local shootdown" },
{ 3, "local mm shootdown" })"
* tag 'trace-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (27 commits)
tracing: Add enum_map file to show enums that have been mapped
writeback: Export enums used by tracepoint to user space
v4l: Export enums used by tracepoints to user space
SUNRPC: Export enums in tracepoints to user space
mm: tracing: Export enums in tracepoints to user space
irq/tracing: Export enums in tracepoints to user space
f2fs: Export the enums in the tracepoints to userspace
net/9p/tracing: Export enums in tracepoints to userspace
x86/tlb/trace: Export enums in used by tlb_flush tracepoint
tracing/samples: Update the trace-event-sample.h with TRACE_DEFINE_ENUM()
tracing: Allow for modules to convert their enums to values
tracing: Add TRACE_DEFINE_ENUM() macro to map enums to their values
tracing: Update trace-event-sample with TRACE_SYSTEM_VAR documentation
tracing: Give system name a pointer
brcmsmac: Move each system tracepoints to their own header
iwlwifi: Move each system tracepoints to their own header
mac80211: Move message tracepoints to their own header
tracing: Add TRACE_SYSTEM_VAR to xhci-hcd
tracing: Add TRACE_SYSTEM_VAR to kvm-s390
tracing: Add TRACE_SYSTEM_VAR to intel-sst
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
New code will require TRACE_SYSTEM to be a valid C variable name,
but some tracepoints have TRACE_SYSTEM with '-' and not '_', so
it can not be used. Instead, add a TRACE_SYSTEM_VAR that can
give the tracing infrastructure a unique name for the trace system.
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
We want the fixes in here, and to help resolve merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
