| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a small number of USB fixes for 5.12-rc3 to resolve a bunch
of reported issues:
- usbip fixups for issues found by syzbot
- xhci driver fixes and quirk additions
- gadget driver fixes
- dwc3 QCOM driver fix
- usb-serial new ids and fixes
- usblp fix for a long-time issue
- cdc-acm quirk addition
- other tiny fixes for reported problems
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
xhci: Fix repeated xhci wake after suspend due to uncleared internal wake state
usb: xhci: Fix ASMedia ASM1042A and ASM3242 DMA addressing
xhci: Improve detection of device initiated wake signal.
usb: xhci: do not perform Soft Retry for some xHCI hosts
usbip: fix vudc usbip_sockfd_store races leading to gpf
usbip: fix vhci_hcd attach_store() races leading to gpf
usbip: fix stub_dev usbip_sockfd_store() races leading to gpf
usbip: fix vudc to check for stream socket
usbip: fix vhci_hcd to check for stream socket
usbip: fix stub_dev to check for stream socket
usb: dwc3: qcom: Add missing DWC3 OF node refcount decrement
USB: usblp: fix a hang in poll() if disconnected
USB: gadget: udc: s3c2410_udc: fix return value check in s3c2410_udc_probe()
usb: renesas_usbhs: Clear PIPECFG for re-enabling pipe with other EPNUM
usb: dwc3: qcom: Honor wakeup enabled/disabled state
usb: gadget: f_uac1: stop playback on function disable
usb: gadget: f_uac2: always increase endpoint max_packet_size by one audio slot
USB: gadget: u_ether: Fix a configfs return code
usb: dwc3: qcom: add ACPI device id for sc8180x
Goodix Fingerprint device is not a modem
...
|
|
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501aa ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501aa ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB devices cannot perform DMA and hence have no dma_mask set in their
device structure. Therefore importing dmabuf into a USB-based driver
fails, which breaks joining and mirroring of display in X11.
For USB devices, pick the associated USB controller as attachment device.
This allows the DRM import helpers to perform the DMA setup. If the DMA
controller does not support DMA transfers, we're out of luck and cannot
import. Our current USB-based DRM drivers don't use DMA, so the actual
DMA device is not important.
Tested by joining/mirroring displays of udl and radeon under Gnome/X11.
v8:
* release dmadev if device initialization fails (Noralf)
* fix commit description (Noralf)
v7:
* fix use-before-init bug in gm12u320 (Dan)
v6:
* implement workaround in DRM drivers and hold reference to
DMA device while USB device is in use
* remove dev_is_usb() (Greg)
* collapse USB helper into usb_intf_get_dma_device() (Alan)
* integrate Daniel's TODO statement (Daniel)
* fix typos (Greg)
v5:
* provide a helper for USB interfaces (Alan)
* add FIXME item to documentation and TODO list (Daniel)
v4:
* implement workaround with USB helper functions (Greg)
* use struct usb_device->bus->sysdev as DMA device (Takashi)
v3:
* drop gem_create_object
* use DMA mask of USB controller, if any (Daniel, Christian, Noralf)
v2:
* move fix to importer side (Christian, Daniel)
* update SHMEM and CMA helpers for new PRIME callbacks
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 6eb0233ec2d0 ("usb: don't inherity DMA properties for USB devices")
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210303133229.3288-1-tzimmermann@suse.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.12-rc3
Here's a fix for a long-standing memory leak after probe failure in
io_edgeport and a fix for a NULL-deref on disconnect in the new xr
driver.
Included are also some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.12-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: io_edgeport: fix memory leak in edge_startup
USB: serial: ch341: add new Product ID
USB: serial: xr: fix NULL-deref on disconnect
USB: serial: cp210x: add some more GE USB IDs
USB: serial: cp210x: add ID for Acuity Brands nLight Air Adapter
|
|
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb gadget device from usbip host. vhci_hcd sends
import request and usbip_sockfd_store() exports the device if it is
free for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down. Device status is shared between host and client.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
Fixes: 9720b4bc76a83807 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/b1c08b983ffa185449c9f0f7d1021dc8c8454b60.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
attach_store() is invoked when user requests import (attach) a device
from usbip host.
Attach and detach are governed by local state and shared state
- Shared state (usbip device status) - Device status is used to manage
the attach and detach operations on import-able devices.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- Device has to be in the right state to be attached and detached.
Attach sequence includes validating the socket and creating receive (rx)
and transmit (tx) threads to talk to the host to get access to the
imported device. rx and tx threads depends on local and shared state to
be correct and in sync.
Detach sequence shuts the socket down and stops the rx and tx threads.
Detach sequence relies on local and shared states to be in sync.
There are races in updating the local and shared status in the current
attach sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to VDEV_ST_NOTASSIGNED. This opens
up a race condition between the threads, port connect, and detach
handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold vhci and usbip_device locks to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to VDEV_ST_NOTASSIGNED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the attach sequence.
- Update usbip_device tcp_rx and tcp_tx pointers holding vhci and
usbip_device locks.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
Fixes: 9720b4bc76a83807 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/bb434bd5d7a64fbec38b5ecfb838a6baef6eb12b.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip_sockfd_store() is invoked when user requests attach (import)
detach (unimport) usb device from usbip host. vhci_hcd sends import
request and usbip_sockfd_store() exports the device if it is free
for export.
Export and unexport are governed by local state and shared state
- Shared state (usbip device status, sockfd) - sockfd and Device
status are used to determine if stub should be brought up or shut
down.
- Local state (tcp_socket, rx and tx thread task_struct ptrs)
A valid tcp_socket controls rx and tx thread operations while the
device is in exported state.
- While the device is exported, device status is marked used and socket,
sockfd, and thread pointers are valid.
Export sequence (stub-up) includes validating the socket and creating
receive (rx) and transmit (tx) threads to talk to the client to provide
access to the exported device. rx and tx threads depends on local and
shared state to be correct and in sync.
Unexport (stub-down) sequence shuts the socket down and stops the rx and
tx threads. Stub-down sequence relies on local and shared states to be
in sync.
There are races in updating the local and shared status in the current
stub-up sequence resulting in crashes. These stem from starting rx and
tx threads before local and global state is updated correctly to be in
sync.
1. Doesn't handle kthread_create() error and saves invalid ptr in local
state that drives rx and tx threads.
2. Updates tcp_socket and sockfd, starts stub_rx and stub_tx threads
before updating usbip_device status to SDEV_ST_USED. This opens up a
race condition between the threads and usbip_sockfd_store() stub up
and down handling.
Fix the above problems:
- Stop using kthread_get_run() macro to create/start threads.
- Create threads and get task struct reference.
- Add kthread_create() failure handling and bail out.
- Hold usbip_device lock to update local and shared states after
creating rx and tx threads.
- Update usbip_device status to SDEV_ST_USED.
- Update usbip_device tcp_socket, sockfd, tcp_rx, and tcp_tx
- Start threads after usbip_device (tcp_socket, sockfd, tcp_rx, tcp_tx,
and status) is complete.
Credit goes to syzbot and Tetsuo Handa for finding and root-causing the
kthread_get_run() improper error handling problem and others. This is a
hard problem to find and debug since the races aren't seen in a normal
case. Fuzzing forces the race window to be small enough for the
kthread_get_run() error path bug and starting threads before updating the
local and shared state bug in the stub-up sequence.
Tested with syzbot reproducer:
- https://syzkaller.appspot.com/text?tag=ReproC&x=14801034d00000
Fixes: 9720b4bc76a83807 ("staging/usbip: convert to kthread")
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+a93fba6d384346a761e3@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+bf1a360e305ee719e364@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+95ce4b142579611ef0a9@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/268a0668144d5ff36ec7d87fdfa90faf583b7ccc.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix usbip_sockfd_store() to validate the passed in file descriptor is
a stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Cc: stable@vger.kernel.org
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/387a670316002324113ac7ea1e8b53f4085d0c95.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix attach_store() to validate the passed in file descriptor is a
stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Cc: stable@vger.kernel.org
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/52712aa308915bda02cece1589e04ee8b401d1f3.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix usbip_sockfd_store() to validate the passed in file descriptor is
a stream socket. If the file descriptor passed was a SOCK_DGRAM socket,
sock_recvmsg() can't detect end of stream.
Cc: stable@vger.kernel.org
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/e942d2bd03afb8e8552bd2a5d84e18d17670d521.1615171203.git.skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_get_child_by_name() increments the reference counter of the OF node it
managed to find. So after the code is done using the device node, the
refcount must be decremented. Add missing of_node_put() invocation then
to the dwc3_qcom_of_register_core() method, since DWC3 OF node is being
used only there.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20210212205521.14280-1-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apparently an application that opens a device and calls select()
on it, will hang if the decice is disconnected. It's a little
surprising that we had this bug for 15 years, but apparently
nobody ever uses select() with a printer: only write() and read(),
and those work fine. Well, you can also select() with a timeout.
The fix is modeled after devio.c. A few other drivers check the
condition first, then do not add the wait queue in case the
device is disconnected. We doubt that's completely race-free.
So, this patch adds the process first, then locks properly
and checks for the disconnect.
Reviewed-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303221053.1cf3313e@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error, the function devm_platform_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
Fixes: 188db4435ac6 ("usb: gadget: s3c: use platform resources")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210305034927.3232386-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the datasheet, this controller has a restriction
which "set an endpoint number so that combinations of the DIR bit and
the EPNUM bits do not overlap.". However, since the udc core driver is
possible to assign a bulk pipe as an interrupt endpoint, an endpoint
number may not match the pipe number. After that, when user rebinds
another gadget driver, this driver broke the restriction because
the driver didn't clear any configuration in usb_ep_disable().
Example:
# modprobe g_ncm
Then, EP3 = pipe 3, EP4 = pipe 4, EP5 = pipe 6
# rmmod g_ncm
# modprobe g_hid
Then, EP3 = pipe 6, EP4 = pipe 7.
So, pipe 3 and pipe 6 are set as EP3.
So, clear PIPECFG register in usbhs_pipe_free().
Fixes: dfb87b8bfe09 ("usb: renesas_usbhs: gadget: fix re-enabling pipe without re-connecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1615168538-26101-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc3-qcom currently enables wakeup interrupts unconditionally
when suspending, however this should not be done when wakeup is
disabled (e.g. through the sysfs attribute power/wakeup). Only
enable wakeup interrupts when device_may_wakeup() returns true.
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210302103659.v2.1.I44954d9e1169f2cf5c44e6454d357c75ddfa99a2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is missing playback stop/cleanup in case of
gadget's ->disable callback that happens on
events like USB host resetting or gadget disconnection
Fixes: 0591bc236015 ("usb: gadget: add f_uac1 variant based on a new u_audio api")
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-3-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per UAC2 Audio Data Formats spec (2.3.1.1 USB Packets),
if the sampling rate is a constant, the allowable variation
of number of audio slots per virtual frame is +/- 1 audio slot.
It means that endpoint should be able to accept/send +1 audio
slot.
Previous endpoint max_packet_size calculation code
was adding sometimes +1 audio slot due to DIV_ROUND_UP
behaviour which was rounding up to closest integer.
However this doesn't work if the numbers are divisible.
It had no any impact with Linux hosts which ignore
this issue, but in case of more strict Windows it
caused rejected enumeration
Thus always add +1 audio slot to endpoint's max packet size
Fixes: 913e4a90b6f9 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Cc: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org> #v4.3+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-2-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the string is invalid, this should return -EINVAL instead of 0.
Fixes: 73517cf49bd4 ("usb: gadget: add RNDIS configfs options for class/subclass/protocol")
Cc: stable <stable@vger.kernel.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YCqZ3P53yyIg5cn7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It enables USB Host support for sc8180x ACPI boot, both the standalone
one and the one behind URS (USB Role Switch). And they share the
the same dwc3_acpi_pdata with sdm845.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210301075745.20544-1-shawn.guo@linaro.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
Signed-off-by: Yorick de Wid <ydewid@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210213144901.53199-1-ydewid@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sysbot found memory leak in edge_startup().
The problem was that when an error was received from the usb_submit_urb(),
nothing was cleaned up.
Reported-by: syzbot+59f777bdcbdd7eea5305@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable@vger.kernel.org # 2.6.21: c5c0c55598ce
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add PID for CH340 that's found on cheap programmers.
The driver works flawlessly as soon as the new PID (0x9986) is added to it.
These look like ANU232MI but ship with a ch341 inside. They have no special
identifiers (mine only has the string "DB9D20130716" printed on the PCB and
nothing identifiable on the packaging. The merchant i bought it from
doesn't sell these anymore).
the lsusb -v output is:
Bus 001 Device 009: ID 9986:7523
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x9986
idProduct 0x7523
bcdDevice 2.54
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0027
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 96mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 1
bInterfaceProtocol 2
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
Signed-off-by: Niv Sardi <xaiki@evilgiggle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Claiming the sibling control interface is a bit more involved and
specifically requires adding support to USB-serial core for managing
either interface being unbound first, something which could otherwise
lead to a NULL-pointer dereference.
Similarly, additional infrastructure is also needed to handle suspend
properly.
Since the driver currently isn't actually using the control interface,
we can defer this for now by simply not claiming the control interface.
Fixes: c2d405aa86b4 ("USB: serial: add MaxLinear/Exar USB to Serial driver")
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tested-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
GE CS1000 has some more custom USB IDs for CP2102N; add them
to the driver to have working auto-probing.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
IDs of nLight Air Adapter, Acuity Brands, Inc.:
vid: 10c4
pid: 88d8
Signed-off-by: Karan Singhal <karan.singhal@acuitybrands.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Fix false-positive build warnings for ARCH=ia64 builds
- Optimize dictionary size for module compression with xz
- Check the compiler and linker versions in Kconfig
- Fix misuse of extra-y
- Support DWARF v5 debug info
- Clamp SUBLEVEL to 255 because stable releases 4.4.x and 4.9.x
exceeded the limit
- Add generic syscall{tbl,hdr}.sh for cleanups across arches
- Minor cleanups of genksyms
- Minor cleanups of Kconfig
* tag 'kbuild-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (38 commits)
initramfs: Remove redundant dependency of RD_ZSTD on BLK_DEV_INITRD
kbuild: remove deprecated 'always' and 'hostprogs-y/m'
kbuild: parse C= and M= before changing the working directory
kbuild: reuse this-makefile to define abs_srctree
kconfig: unify rule of config, menuconfig, nconfig, gconfig, xconfig
kconfig: omit --oldaskconfig option for 'make config'
kconfig: fix 'invalid option' for help option
kconfig: remove dead code in conf_askvalue()
kconfig: clean up nested if-conditionals in check_conf()
kconfig: Remove duplicate call to sym_get_string_value()
Makefile: Remove # characters from compiler string
Makefile: reuse CC_VERSION_TEXT
kbuild: check the minimum linker version in Kconfig
kbuild: remove ld-version macro
scripts: add generic syscallhdr.sh
scripts: add generic syscalltbl.sh
arch: syscalls: remove $(srctree)/ prefix from syscall tables
arch: syscalls: add missing FORCE and fix 'targets' to make if_changed work
gen_compile_commands: prune some directories
kbuild: simplify access to the kernel's version
...
|
|
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
|
|
Instead of storing the version in a single integer and having various
kernel (and userspace) code how it's constructed, export individual
(major, patchlevel, sublevel) components and simplify kernel code that
uses it.
This should also make it easier on userspace.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
of_dev_get() and of_dev_put are just wrappers for get_device()/put_device()
on a platform_device. There's also already platform_device_{get,put}()
wrappers for this purpose. Let's update the few users and remove
of_dev_{get,put}().
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Gilles Muller <Gilles.Muller@inria.fr>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210211232745.1498137-2-robh@kernel.org
|
|
Based on
https://lore.kernel.org/linux-arm-kernel/YCJv59g3Tq2haDSa@kroah.com/
initialization should fail if any registration fails.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/a8547f6fe698014df08cad3bcc9c5d9a7137d8b8.1612873935.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As started by commit 05a5f51ca566 ("Documentation: Replace lkml.org
links with lore"), replace lkml.org links with lore to better use a
single source that's more likely to stay available long-term.
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210210235330.3292719-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
reliable
Without this quirk starting a video capture from the device often fails with
kernel: uvcvideo: Failed to set UVC probe control : -110 (exp. 34).
Signed-off-by: Stefan Ursella <stefan.ursella@wolfvision.net>
Link: https://lore.kernel.org/r/20210210140713.18711-1-stefan.ursella@wolfvision.net
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.12-rc1
Here are the USB-serial updates for 5.12-rc1, including:
- a line-speed fix for newer pl2303 devices
- a line-speed fix for FTDI FT-X devices
- a new xr_serial driver for MaxLinear/Exar devices (non-ACM mode)
- a cdc-acm blacklist entry for when the xr_serial driver is enabled
- cp210x support for software flow control
- various cp210x modem-control fixes
- an updated ZTE P685M modem entry to stop claiming the QMI interface
- an update to drop the port_remove() driver-callback return value
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (41 commits)
USB: serial: drop bogus to_usb_serial_port() checks
USB: serial: make remove callback return void
USB: serial: drop if with an always false condition
USB: serial: option: update interface mapping for ZTE P685M
USB: serial: ftdi_sio: restore divisor-encoding comments
USB: serial: ftdi_sio: fix FTX sub-integer prescaler
USB: serial: cp210x: clean up auto-RTS handling
USB: serial: cp210x: fix RTS handling
USB: serial: cp210x: clean up printk zero padding
USB: serial: cp210x: clean up flow-control debug message
USB: serial: cp210x: drop shift macros
USB: serial: cp210x: fix modem-control handling
USB: serial: cp210x: suppress modem-control errors
USB: serial: mos7720: fix error code in mos7720_write()
USB: serial: xr: fix B0 handling
USB: serial: xr: fix pin configuration
USB: serial: xr: fix gpio-mode handling
USB: serial: xr: simplify line-speed logic
USB: serial: xr: clean up line-settings handling
USB: serial: xr: document vendor-request recipient
...
|
|
Move the last entry to its proper place to maintain the VID/PID sort
order.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210210111746.13360-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The to_usb_serial_port() macro is implemented using container_of() so
there's no need to check for NULL.
Note that neither bus match() or probe() is ever called with a NULL
struct device pointer so the checks weren't just misplaced.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
All usb_serial drivers return 0 in their remove callbacks and driver
core ignores the value returned by usb_serial_device_remove(). So change
the remove callback to return void and return 0 unconditionally in
usb_serial_device_remove().
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210208143149.963644-2-uwe@kleine-koenig.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In a bus remove function the passed device is always valid, so there is
no need to check for it being NULL.
(Side note: The check for port being non-NULL is broken anyhow, because
to_usb_serial_port() is a wrapper around container_of() for a member that is
not the first one. So port can hardly become NULL.)
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210208143149.963644-1-uwe@kleine-koenig.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix the following coccicheck warnings:
./drivers/usb/gadget/udc/udc-xilinx.c:846:1-17: WARNING: Assignment of
0/1 to bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1612678696-15794-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a079973f462a ("usb: typec: tcpm: Remove tcpc_config
configuration mechanism") removed the tcpc_config which includes the
Sink VDO and it is not yet added back with fwnode. Add it now.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-8-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
VDM header now requires SVDM Version. Get it from typec_partner.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-6-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch implements the following requirement in the Spec.
PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10
6.4.4.2.3 Structured VDM Version
"The Structured VDM Version field of the Discover Identity Command
sent and received during VDM discovery Shall be used to determine the
lowest common Structured VDM Version supported by the Port Partners or
Cable Plug and Shall continue to operate using this Specification
Revision until they are Detached."
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-5-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10
6.4.4.2.3 Structured VDM Version
"The Structured VDM Version field of the Discover Identity Command
sent and received during VDM discovery Shall be used to determine the
lowest common Structured VDM Version supported by the Port Partners or
Cable Plug and Shall continue to operate using this Specification
Revision until they are Detached."
Also clear the fields newly defined in SVDM version 2.0 if the
negotiated SVDM version is 1.0.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Rev 3.0 introduces SVDM Version 2.0. This patch makes the field
configuable in the header in order to be able to be compatible with
older SVDM version.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10
6.4.4.2.3 Structured VDM Version
"The Structured VDM Version field of the Discover Identity Command
sent and received during VDM discovery Shall be used to determine the
lowest common Structured VDM Version supported by the Port Partners or
Cable Plug and Shall continue to operate using this Specification
Revision until they are Detached."
Add a variable in typec_capability to specify the highest SVDM version
supported by the port and another variable in typec_partner to cache the
negotiated SVDM version between the port and the partner.
Also add setter/getter functions for the negotiated SVDM version.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dep->interval captures the number of frames/microframes per interval
from bInterval. Fullspeed interrupt endpoint bInterval is the number of
frames per interval and not 2^(bInterval - 1). So fix it here. This
change is only for debugging purpose and should not affect the interrupt
endpoint operation.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1263b563dedc4ab8b0fb854fba06ce4bc56bd495.1612820995.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Valid range for DEPCFG.bInterval_m1 is from 0 to 13, and it must be set
to 0 when the controller operates in full-speed. See the programming
guide for DEPCFG command section 3.2.2.1 (v3.30a).
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f57026f993c0ce71498dbb06e49b3a47c4d0265.1612820995.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
