| Age | Commit message (Collapse) | Author |
|---|
|
IPA configuration data includes an array of memory region
descriptors. That was a fixed-size array at one time, but
at some point we started defining it such that it was only
as big as required for a given platform. The actual number
of entries in the array is recorded in the configuration data
along with the array.
A loop in ipa_mem_config() still assumes the array has entries
for all defined memory region IDs. As a result, this loop can
go past the end of the actual array and attempt to write
"canary" values based on nonsensical data.
Fix this, by stashing the number of entries in the array, and
using that rather than IPA_MEM_COUNT in the initialization loop
found in ipa_mem_config().
The only remaining use of IPA_MEM_COUNT is in a validation check
to ensure configuration data doesn't have too many entries.
That's fine for now.
Fixes: 3128aae8c439a ("net: ipa: redefine struct ipa_mem_data")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IONIC=y and PTP_1588_CLOCK=m were set in the .config file
the driver link failed with undefined references.
We add the dependancy
depends on PTP_1588_CLOCK || !PTP_1588_CLOCK
to clear this up.
If PTP_1588_CLOCK=m, the depends limits IONIC to =m (or disabled).
If PTP_1588_CLOCK is disabled, IONIC can be any of y/m/n.
Fixes: 61db421da31b ("ionic: link in the new hw timestamp code")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
pull-request: mac80211 2021-05-11
So exciting times, for the first pull request for fixes I
have a bunch of security things that have been under embargo
for a while - see more details in the tag below, and at the
patch posting message I linked to.
I organized with Kalle to just have a single set of fixes
for mac80211 and ath10k/ath11k, we don't know about any of
the other vendors (the mac80211 + already released firmware
is sufficient to fix iwlwifi.)
Please pull and let me know if there's any problem.
Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), and this contains the
fixes developed for mac80211 and specifically Qualcomm drivers, I'm
sending this together (as agreed with Kalle) to have just a single
set of patches for now. We don't know about other vendors though.
More details in the patch posting:
https://lore.kernel.org/r/20210511180259.159598-1-johannes@sipsolutions.net
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both get and set WoL will check device_can_wakeup(), if MAC supports PMT, it
will set device wakeup capability. After commit 1d8e5b0f3f2c ("net: stmmac:
Support WOL with phy"), device wakeup capability will be overwrite in
stmmac_init_phy() according to phy's Wol feature. If phy doesn't support WoL,
then MAC will lose wakeup capability. To fix this issue, only overwrite device
wakeup capability when MAC doesn't support PMT.
For STMMAC now driver checks MAC's WoL capability if MAC supports PMT, if
not support, driver will check PHY's WoL capability.
Fixes: 1d8e5b0f3f2c ("net: stmmac: Support WOL with phy")
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fragmentation is used only with unicast frames. Drop multicast fragments
to avoid any undesired behavior.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.1d53bfd20a8b.Ibb63283051bb5e2c45951932c6e1f351d5a73dc3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the fragment cache setup during peer assoc is
cleared only during peer delete. In case a key reinstallation
happens with the same peer, the same fragment cache with old
fragments added before key installation could be clubbed
with fragments received after. This might be exploited
to mix fragments of different data resulting in a proper
unintended reassembled packet to be passed up the stack.
Hence flush the fragment cache on every key installation to prevent
potential attacks (CVE-2020-24587).
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.218dc777836f.I9af6fc76215a35936c4152552018afb5079c5d8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In certain scenarios a normal MSDU can be received as an A-MSDU when
the A-MSDU present bit of a QoS header gets flipped during reception.
Since this bit is unauthenticated, the hardware crypto engine can pass
the frame to the driver without any error indication.
This could result in processing unintended subframes collected in the
A-MSDU list. Hence, validate A-MSDU list by checking if the first frame
has a valid subframe header.
Comparing the non-aggregated MSDU and an A-MSDU, the fields of the first
subframe DA matches the LLC/SNAP header fields of a normal MSDU.
In order to avoid processing such frames, add a validation to
filter such A-MSDU frames where the first subframe header DA matches
with the LLC/SNAP header pattern.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.10-00047
Cc: stable@vger.kernel.org
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.e6f5eb7b9847.I38a77ae26096862527a5eab73caebd7346af8b66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
TKIP Michael MIC was not verified properly for PCIe cases since the
validation steps in ieee80211_rx_h_michael_mic_verify() in mac80211 did
not get fully executed due to unexpected flag values in
ieee80211_rx_status.
Fix this by setting the flags property to meet mac80211 expectations for
performing Michael MIC validation there. This fixes CVE-2020-26141. It
does the same as ath10k_htt_rx_proc_rx_ind_hl() for SDIO which passed
MIC verification case. This applies only to QCA6174/QCA9377 PCIe.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.c3f1d42c6746.I795593fcaae941c471425b8c7d5f7bb185d29142@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the discard flag is set by the firmware for an MPDU, it should be
dropped. This allows a mitigation for CVE-2020-24588 to be implemented
in the firmware.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.11968c725b5c.Idd166365ebea2771c0c0a38c78b5060750f90e17@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fragmentation is not used with multicast frames. Discard unexpected
fragments with multicast DA. This fixes CVE-2020-26145.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.9ca6ca7945a9.I1e18b514590af17c155bda86699bc3a971a8dcf4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fragmentation is not used with multicast frames. Discard unexpected
fragments with multicast DA. This fixes CVE-2020-26145.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.5a0bd289bda8.Idd6ebea20038fb1cfee6de924aa595e5647c9eae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PN replay check for not fragmented frames is finished in the firmware,
but this was not done for fragmented frames when ath10k is used with
QCA6174/QCA6377 PCIe. mac80211 has the function
ieee80211_rx_h_defragment() for PN replay check for fragmented frames,
but this does not get checked with QCA6174 due to the
ieee80211_has_protected() condition not matching the cleared Protected
bit case.
Validate the PN of received fragmented frames within ath10k when CCMP is
used and drop the fragment if the PN is not correct (incremented by
exactly one from the previous fragment). This applies only for
QCA6174/QCA6377 PCIe.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.9ba2664866a4.I756e47b67e210dba69966d989c4711ffc02dc6bc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 316bcffe4479 ("net: dsa: felix: disable always guard band bit for
TAS config") disabled the guard band and broke 802.3Qbv compliance.
There are two issues here:
(1) Without the guard band the end of the scheduling window could be
overrun by a frame in transit.
(2) Frames that don't fit into a configured window will still be sent.
The reason for both issues is that the switch will schedule the _start_
of a frame transmission inside the predefined window without taking the
length of the frame into account. Thus, we'll need the guard band which
will close the gate early, so that a complete frame can still be sent.
Revert the commit and add a note.
For a lengthy discussion see [1].
[1] https://lore.kernel.org/netdev/c7618025da6723418c56a54fe4683bd7@walle.cc/
Fixes: 316bcffe4479 ("net: dsa: felix: disable always guard band bit for TAS config")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix SFP and QSFP* EEPROM queries by setting i2c_address, offset and page
number correctly. For SFP set the following params:
- I2C address for offsets 0-255 is 0x50. For 256-511 - 0x51.
- Page number is zero.
- Offset is 0-255.
At the same time, QSFP* parameters are different:
- I2C address is always 0x50.
- Page number is not limited to zero.
- Offset is 0-255 for page zero and 128-255 for others.
To set parameters accordingly to cable used, implement function to query
module ID and implement respective helper functions to set parameters
correctly.
Fixes: 135dd9594f12 ("net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ret' is known to be 0 here.
The expected error code is stored in 'tx_pipe->dma_queue', so use it
instead.
While at it, switch from %d to %pe which is more user friendly.
Fixes: 84640e27f230 ("net: netcp: Add Keystone NetCP core ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes in various drivers (qla2xxx, ufs,
scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
driver to remove the open coded iteration functions in favour of the
scsi provided ones"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Use scsi_host_busy_iter() to traverse commands
scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
scsi: ufs: core: Narrow down fast path in system suspend path
scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
scsi: ufs: core: Do not put UFS power into LPM if link is broken
scsi: qla2xxx: Prevent PRLI in target mode
scsi: qla2xxx: Add marginal path handling support
scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
scsi: ufs: core: Fix a typo in ufs-sysfs.c
scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
scsi: lpfc: Fix illegal memory access on Abort IOCBs
scsi: blk-mq: Fix build warning when making htmldocs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Convert sh and sparc to use generic shell scripts to generate the
syscall headers
- refactor .gitignore files
- Update kernel/config_data.gz only when the content of the .config
is really changed, which avoids the unneeded re-link of vmlinux
- move "remove stale files" workarounds to scripts/remove-stale-files
- suppress unused-but-set-variable warnings by default for Clang
as well
- fix locale setting LANG=C to LC_ALL=C
- improve 'make distclean'
- always keep intermediate objects from scripts/link-vmlinux.sh
- move IF_ENABLED out of <linux/kconfig.h> to make it self-contained
- misc cleanups
* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
kbuild: Don't remove link-vmlinux temporary files on exit/signal
kbuild: remove the unneeded comments for external module builds
kbuild: make distclean remove tag files in sub-directories
kbuild: make distclean work against $(objtree) instead of $(srctree)
kbuild: refactor modname-multi by using suffix-search
kbuild: refactor fdtoverlay rule
kbuild: parameterize the .o part of suffix-search
arch: use cross_compiling to check whether it is a cross build or not
kbuild: remove ARCH=sh64 support from top Makefile
.gitignore: prefix local generated files with a slash
kbuild: replace LANG=C with LC_ALL=C
Makefile: Move -Wno-unused-but-set-variable out of GCC only block
kbuild: add a script to remove stale generated files
kbuild: update config_data.gz only when the content of .config is changed
.gitignore: ignore only top-level modules.builtin
.gitignore: move tags and TAGS close to other tag files
kernel/.gitgnore: remove stale timeconst.h and hz.bc
usr/include: refactor .gitignore
genksyms: fix stale comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc1, including fixes from bpf, can and
netfilter trees. Self-contained fixes, nothing risky.
Current release - new code bugs:
- dsa: ksz: fix a few bugs found by static-checker in the new driver
- stmmac: fix frame preemption handshake not triggering after
interface restart
Previous releases - regressions:
- make nla_strcmp handle more then one trailing null character
- fix stack OOB reads while fragmenting IPv4 packets in openvswitch
and net/sched
- sctp: do asoc update earlier in sctp_sf_do_dupcook_a
- sctp: delay auto_asconf init until binding the first addr
- stmmac: clear receive all(RA) bit when promiscuous mode is off
- can: mcp251x: fix resume from sleep before interface was brought up
Previous releases - always broken:
- bpf: fix leakage of uninitialized bpf stack under speculation
- bpf: fix masking negation logic upon negative dst register
- netfilter: don't assume that skb_header_pointer() will never fail
- only allow init netns to set default tcp cong to a restricted algo
- xsk: fix xp_aligned_validate_desc() when len == chunk_size to avoid
false positive errors
- ethtool: fix missing NLM_F_MULTI flag when dumping
- can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
- sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b
- bridge: fix NULL-deref caused by a races between assigning
rx_handler_data and setting the IFF_BRIDGE_PORT bit
Latecomer:
- seg6: add counters support for SRv6 Behaviors"
* tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
atm: firestream: Use fallthrough pseudo-keyword
net: stmmac: Do not enable RX FIFO overflow interrupts
mptcp: fix splat when closing unaccepted socket
i40e: Remove LLDP frame filters
i40e: Fix PHY type identifiers for 2.5G and 5G adapters
i40e: fix the restart auto-negotiation after FEC modified
i40e: Fix use-after-free in i40e_client_subtask()
i40e: fix broken XDP support
netfilter: nftables: avoid potential overflows on 32bit arches
netfilter: nftables: avoid overflows in nft_hash_buckets()
tcp: Specify cmsgbuf is user pointer for receive zerocopy.
mlxsw: spectrum_mr: Update egress RIF list before route's action
net: ipa: fix inter-EE IRQ register definitions
can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
can: mcp251x: fix resume from sleep before interface was brought up
can: mcp251xfd: mcp251xfd_probe(): add missing can_rx_offload_del() in error path
can: mcp251xfd: mcp251xfd_probe(): fix an error pointer dereference in probe
netfilter: nftables: Fix a memleak from userdata error path in new objects
netfilter: remove BUG_ON() after skb_header_pointer()
netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check
...
|
|
<linux/kconfig.h> is included from all the kernel-space source files,
including C, assembly, linker scripts. It is intended to contain a
minimal set of macros to evaluate CONFIG options.
IF_ENABLED() is an intruder here because (x ? y : z) is C code, which
should not be included from assembly files or linker scripts.
Also, <linux/kconfig.h> is no longer self-contained because NULL is
defined in <linux/stddef.h>.
Move IF_ENABLED() out to <linux/kernel.h> as PTR_IF(). PTF_IF()
takes the general boolean expression instead of a CONFIG option
so that it fits better in <linux/kernel.h>.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Nguyen, Anthony L says:
====================
Intel Wired LAN Driver Updates 2021-05-07
This series contains updates to i40e driver only.
Magnus fixes XDP by adding and correcting checks that were caused by a
previous commit which introduced a new variable but did not account for
it in all paths.
Yunjian Wang adds a return in an error path to prevent reading a freed
pointer.
Jaroslaw forces link reset when changing FEC so that changes take
affect.
Mateusz fixes PHY types for 2.5G and 5G as there is a differentiation on
PHY identifiers based on operation.
Arkadiusz removes filtering of LLDP frames for software DCB as this is
preventing them from being properly transmitted.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Remove LLDP frame filters
i40e: Fix PHY type identifiers for 2.5G and 5G adapters
i40e: fix the restart auto-negotiation after FEC modified
i40e: Fix use-after-free in i40e_client_subtask()
i40e: fix broken XDP support
====================
Link: https://lore.kernel.org/r/20210507164151.2878147-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add pseudo-keyword macro fallthrough[1]
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Link: https://lore.kernel.org/r/20210507123843.10602-1-jj251510319013@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- Changes around DP mode check, hard reset, tracking port change.
cros_ec misc:
- wilco_ec: Convert stream-like files from nonseekable to stream open
- cros_usbpd_notify: Listen to EC_HSOT_EVENT_USB_MUX host event
- fix format warning in cros_ec_typec"
* tag 'tag-chrome-platform-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_lpc: Use DEFINE_MUTEX() for mutex lock
platform/chrome: cros_usbpd_notify: Listen to EC_HOST_EVENT_USB_MUX host event
platform/chrome: cros_ec_typec: Add DP mode check
platform/chrome: cros_ec_typec: Handle hard reset
platform/chrome: cros_ec: Add Type C hard reset
platform/chrome: cros_ec_typec: Track port role
platform/chrome: cros_ec_typec: fix clang -Wformat warning
platform/chrome: cros_ec_typec: Check for device within remove function
platform/chrome: wilco_ec: convert stream-like files from nonseekable_open -> stream_open
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3cupdates from Alexandre Belloni:
"Fix i3c_master_register error path"
* tag 'i3c/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
Revert "i3c master: fix missing destroy_workqueue() on error in i3c_master_register"
dt-bindings: i3c: Fix silvaco,i3c-master-v1 compatible string
i3c: master: svc: remove redundant assignment to cmd->read_len
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"A mix of fixes and clean-ups that turned up too late for the first
pull request:
- Restore terminal stack frame records. Their previous removal caused
traces which cross secondary_start_kernel to terminate one entry
too late, with a spurious "0" entry.
- Fix boot warning with pseudo-NMI due to the way we manipulate the
PMR register.
- ACPI fixes: avoid corruption of interrupt mappings on watchdog
probe failure (GTDT), prevent unregistering of GIC SGIs.
- Force SPARSEMEM_VMEMMAP as the only memory model, it saves with
having to test all the other combinations.
- Documentation fixes and updates: tagged address ABI exceptions on
brk/mmap/mremap(), event stream frequency, update booting
requirements on the configuration of traps"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kernel: Update the stale comment
arm64: Fix the documented event stream frequency
arm64: entry: always set GIC_PRIO_PSR_I_SET during entry
arm64: Explicitly document boot requirements for SVE
arm64: Explicitly require that FPSIMD instructions do not trap
arm64: Relax booting requirements for configuration of traps
arm64: cpufeatures: use min and max
arm64: stacktrace: restore terminal records
arm64/vdso: Discard .note.gnu.property sections in vDSO
arm64: doc: Add brk/mmap/mremap() to the Tagged Address ABI Exceptions
psci: Remove unneeded semicolon
ACPI: irq: Prevent unregistering of GIC SGIs
ACPI: GTDT: Don't corrupt interrupt mappings on watchdow probe failure
arm64: Show three registers per line
arm64: remove HAVE_DEBUG_BUGVERBOSE
arm64: alternative: simplify passing alt_region
arm64: Force SPARSEMEM_VMEMMAP as the only memory management model
arm64: vdso32: drop -no-integrated-as flag
|
|
Pull block fixes from Jens Axboe:
- dasd spelling fixes (Bhaskar)
- Limit bio max size on multi-page bvecs to the hardware limit, to
avoid overly large bio's (and hence latencies). Originally queued for
the merge window, but needed a fix and was dropped from the initial
pull (Changheun)
- NVMe pull request (Christoph):
- reset the bdev to ns head when failover (Daniel Wagner)
- remove unsupported command noise (Keith Busch)
- misc passthrough improvements (Kanchan Joshi)
- fix controller ioctl through ns_head (Minwoo Im)
- fix controller timeouts during reset (Tao Chiu)
- rnbd fixes/cleanups (Gioh, Md, Dima)
- Fix iov_iter re-expansion (yangerkun)
* tag 'block-5.13-2021-05-07' of git://git.kernel.dk/linux-block:
block: reexpand iov_iter after read/write
nvmet: remove unsupported command noise
nvme-multipath: reset bdev to ns head when failover
nvme-pci: fix controller reset hang when racing with nvme_timeout
nvme: move the fabrics queue ready check routines to core
nvme: avoid memset for passthrough requests
nvme: add nvme_get_ns helper
nvme: fix controller ioctl through ns_head
bio: limit bio max size
RDMA/rtrs: fix uninitialized symbol 'cnt'
s390: dasd: Mundane spelling fixes
block/rnbd: Remove all likely and unlikely
block/rnbd-clt: Check the return value of the function rtrs_clt_query
block/rnbd: Fix style issues
block/rnbd-clt: Change queue_depth type in rnbd_clt_session to size_t
|
|
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa8078 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f4677a ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196f1 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0ac9 ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 12738ac4754e ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac4754e ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Merge yet more updates from Andrew Morton:
"This is everything else from -mm for this merge window.
90 patches.
Subsystems affected by this patch series: mm (cleanups and slub),
alpha, procfs, sysctl, misc, core-kernel, bitmap, lib, compat,
checkpatch, epoll, isofs, nilfs2, hpfs, exit, fork, kexec, gcov,
panic, delayacct, gdb, resource, selftests, async, initramfs, ipc,
drivers/char, and spelling"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (90 commits)
mm: fix typos in comments
mm: fix typos in comments
treewide: remove editor modelines and cruft
ipc/sem.c: spelling fix
fs: fat: fix spelling typo of values
kernel/sys.c: fix typo
kernel/up.c: fix typo
kernel/user_namespace.c: fix typos
kernel/umh.c: fix some spelling mistakes
include/linux/pgtable.h: few spelling fixes
mm/slab.c: fix spelling mistake "disired" -> "desired"
scripts/spelling.txt: add "overflw"
scripts/spelling.txt: Add "diabled" typo
scripts/spelling.txt: add "overlfow"
arm: print alloc free paths for address in registers
mm/vmalloc: remove vwrite()
mm: remove xlate_dev_kmem_ptr()
drivers/char: remove /dev/kmem for good
mm: fix some typos and code style problems
ipc/sem.c: mundane typo fixes
...
|
|
The section "19) Editor modelines and other cruft" in
Documentation/process/coding-style.rst clearly says, "Do not include any
of these in source files."
I recently receive a patch to explicitly add a new one.
Let's do treewide cleanups, otherwise some people follow the existing code
and attempt to upstream their favoriate editor setups.
It is even nicer if scripts/checkpatch.pl can check it.
If we like to impose coding style in an editor-independent manner, I think
editorconfig (patch [1]) is a saner solution.
[1] https://lore.kernel.org/lkml/20200703073143.423557-1-danny@kdrag0n.dev/
Link: https://lkml.kernel.org/r/20210324054457.1477489-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org> [auxdisplay]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "drivers/char: remove /dev/kmem for good".
Exploring /dev/kmem and /dev/mem in the context of memory hot(un)plug and
memory ballooning, I started questioning the existence of /dev/kmem.
Comparing it with the /proc/kcore implementation, it does not seem to be
able to deal with things like
a) Pages unmapped from the direct mapping (e.g., to be used by secretmem)
-> kern_addr_valid(). virt_addr_valid() is not sufficient.
b) Special cases like gart aperture memory that is not to be touched
-> mem_pfn_is_ram()
Unless I am missing something, it's at least broken in some cases and might
fault/crash the machine.
Looks like its existence has been questioned before in 2005 and 2010 [1],
after ~11 additional years, it might make sense to revive the discussion.
CONFIG_DEVKMEM is only enabled in a single defconfig (on purpose or by
mistake?). All distributions disable it: in Ubuntu it has been disabled
for more than 10 years, in Debian since 2.6.31, in Fedora at least
starting with FC3, in RHEL starting with RHEL4, in SUSE starting from
15sp2, and OpenSUSE has it disabled as well.
1) /dev/kmem was popular for rootkits [2] before it got disabled
basically everywhere. Ubuntu documents [3] "There is no modern user of
/dev/kmem any more beyond attackers using it to load kernel rootkits.".
RHEL documents in a BZ [5] "it served no practical purpose other than to
serve as a potential security problem or to enable binary module drivers
to access structures/functions they shouldn't be touching"
2) /proc/kcore is a decent interface to have a controlled way to read
kernel memory for debugging puposes. (will need some extensions to
deal with memory offlining/unplug, memory ballooning, and poisoned
pages, though)
3) It might be useful for corner case debugging [1]. KDB/KGDB might be a
better fit, especially, to write random memory; harder to shoot
yourself into the foot.
4) "Kernel Memory Editor" [4] hasn't seen any updates since 2000 and seems
to be incompatible with 64bit [1]. For educational purposes,
/proc/kcore might be used to monitor value updates -- or older
kernels can be used.
5) It's broken on arm64, and therefore, completely disabled there.
Looks like it's essentially unused and has been replaced by better
suited interfaces for individual tasks (/proc/kcore, KDB/KGDB). Let's
just remove it.
[1] https://lwn.net/Articles/147901/
[2] https://www.linuxjournal.com/article/10505
[3] https://wiki.ubuntu.com/Security/Features#A.2Fdev.2Fkmem_disabled
[4] https://sourceforge.net/projects/kme/
[5] https://bugzilla.redhat.com/show_bug.cgi?id=154796
Link: https://lkml.kernel.org/r/20210324102351.6932-1-david@redhat.com
Link: https://lkml.kernel.org/r/20210324102351.6932-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Chris Zankel <chris@zankel.net>
Cc: Corentin Labbe <clabbe@baylibre.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hillf Danton <hdanton@sina.com>
Cc: huang ying <huang.ying.caritas@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: James Troup <james.troup@canonical.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kairui Song <kasong@redhat.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: openrisc@lists.librecores.org
Cc: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Pavel Machek (CIP)" <pavel@denx.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Pierre Morel <pmorel@linux.ibm.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Theodore Dubois <tblodt@icloud.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: William Cohen <wcohen@redhat.com>
Cc: Xiaoming Ni <nixiaoming@huawei.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "background initramfs unpacking, and CONFIG_MODPROBE_PATH", v3.
These two patches are independent, but better-together.
The second is a rather trivial patch that simply allows the developer to
change "/sbin/modprobe" to something else - e.g. the empty string, so
that all request_module() during early boot return -ENOENT early, without
even spawning a usermode helper, needlessly synchronizing with the
initramfs unpacking.
The first patch delegates decompressing the initramfs to a worker thread,
allowing do_initcalls() in main.c to proceed to the device_ and late_
initcalls without waiting for that decompression (and populating of
rootfs) to finish. Obviously, some of those later calls may rely on the
initramfs being available, so I've added synchronization points in the
firmware loader and usermodehelper paths - there might be other places
that would need this, but so far no one has been able to think of any
places I have missed.
There's not much to win if most of the functionality needed during boot is
only available as modules. But systems with a custom-made .config and
initramfs can boot faster, partly due to utilizing more than one cpu
earlier, partly by avoiding known-futile modprobe calls (which would still
trigger synchronization with the initramfs unpacking, thus eliminating
most of the first benefit).
This patch (of 2):
Most of the boot process doesn't actually need anything from the
initramfs, until of course PID1 is to be executed. So instead of doing
the decompressing and populating of the initramfs synchronously in
populate_rootfs() itself, push that off to a worker thread.
This is primarily motivated by an embedded ppc target, where unpacking
even the rather modest sized initramfs takes 0.6 seconds, which is long
enough that the external watchdog becomes unhappy that it doesn't get
attention soon enough. By doing the initramfs decompression in a worker
thread, we get to do the device_initcalls and hence start petting the
watchdog much sooner.
Normal desktops might benefit as well. On my mostly stock Ubuntu kernel,
my initramfs is a 26M xz-compressed blob, decompressing to around 126M.
That takes almost two seconds:
[ 0.201454] Trying to unpack rootfs image as initramfs...
[ 1.976633] Freeing initrd memory: 29416K
Before this patch, these lines occur consecutively in dmesg. With this
patch, the timestamps on these two lines is roughly the same as above, but
with 172 lines inbetween - so more than one cpu has been kept busy doing
work that would otherwise only happen after the populate_rootfs()
finished.
Should one of the initcalls done after rootfs_initcall time (i.e., device_
and late_ initcalls) need something from the initramfs (say, a kernel
module or a firmware blob), it will simply wait for the initramfs
unpacking to be done before proceeding, which should in theory make this
completely safe.
But if some driver pokes around in the filesystem directly and not via one
of the official kernel interfaces (i.e. request_firmware*(),
call_usermodehelper*) that theory may not hold - also, I certainly might
have missed a spot when sprinkling wait_for_initramfs(). So there is an
escape hatch in the form of an initramfs_async= command line parameter.
Link: https://lkml.kernel.org/r/20210313212528.2956377-1-linux@rasmusvillemoes.dk
Link: https://lkml.kernel.org/r/20210313212528.2956377-2-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: Hycon HY46XX, ILITEK Lego Series,
and MStar MSG2638
- a new driver for Azoteq IQS626A proximity and touch controller
- addition of Amazon Game Controller to the list of devices handled
by the xpad driver
- Elan touchscreen driver will avoid binding to devices described as
I2CHID compatible in ACPI tables
- various driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (56 commits)
Input: xpad - add support for Amazon Game Controller
Input: ili210x - add missing negation for touch indication on ili210x
MAINTAINERS: repair reference in HYCON HY46XX TOUCHSCREEN SUPPORT
Input: add driver for the Hycon HY46XX touchpanel series
dt-bindings: touchscreen: Add HY46XX bindings
dt-bindings: Add Hycon Technology vendor prefix
Input: cyttsp - flag the device properly
Input: cyttsp - set abs params for ABS_MT_TOUCH_MAJOR
Input: cyttsp - drop the phys path
Input: cyttsp - reduce reset pulse timings
Input: cyttsp - error message on boot mode exit error
Input: apbps2 - remove useless variable
Input: mms114 - support MMS136
Input: mms114 - convert bindings to YAML and extend
Input: Add support for ILITEK Lego Series
dt-bindings: input: touchscreen: ilitek_ts_i2c: Add bindings
Input: add MStar MSG2638 touchscreen driver
dt-bindings: input/touchscreen: add bindings for msg2638
Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state
Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices
...
|
|
My UEK-derived config has 1030 files depending on pagemap.h before this
change. Afterwards, just 326 files need to be rebuilt when I touch
pagemap.h. I think blkdev.h is probably included too widely, but
untangling that dependency is harder and this solves my problem. x86
allmodconfig builds, but there may be implicit include problems on other
architectures.
Link: https://lkml.kernel.org/r/20210309195747.283796-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com> [nvdimm]
Acked-by: Jens Axboe <axboe@kernel.dk> [block]
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> [scsi]
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that proc_ops are separate from file_operations and other operations
it easy to check all instances to have ->proc_lseek hook and remove check
in main code.
Note:
nonseekable_open() files naturally don't require ->proc_lseek.
Garbage collect pde_lseek() function.
[adobriyan@gmail.com: smoke test lseek()]
Link: https://lkml.kernel.org/r/YG4OIhChOrVTPgdN@localhost.localdomain
Link: https://lkml.kernel.org/r/YFYX0Bzwxlc7aBa/@localhost.localdomain
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Each multicast route that is forwarding packets (as opposed to trapping
them) points to a list of egress router interfaces (RIFs) through which
packets are replicated.
A route's action can transition from trap to forward when a RIF is
created for one of the route's egress virtual interfaces (eVIF). When
this happens, the route's action is first updated and only later the
list of egress RIFs is committed to the device.
This results in the route pointing to an invalid list. In case the list
pointer is out of range (due to uninitialized memory), the device will
complain:
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=5733bf490000905c,reg_id=300f(pefa),type=write,status=7(bad parameter))
Fix this by first committing the list of egress RIFs to the device and
only later update the route's action.
Note that a fix is not needed in the reverse function (i.e.,
mlxsw_sp_mr_route_evif_unresolve()), as there the route's action is
first updated and only later the RIF is removed from the list.
Cc: stable@vger.kernel.org
Fixes: c011ec1bbfd6 ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20210506072308.3834303-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf01 ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Amazon Luna controller (product name "Amazon Game Controller") behaves
like an Xbox 360 controller when connected over USB.
Signed-off-by: Matt Reynolds <mattreynolds@chromium.org>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/20210429103548.1.If5f9a44cb81e25b9350f7c6c0b3c88b4ecd81166@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds the negation needed for proper finger detection on Ilitek
ili2107/ili210x. This fixes polling issues (on Amazon Kindle Fire)
caused by returning false for the cooresponding finger on the touchscreen.
Signed-off-by: Hansem Ro <hansemro@outlook.com>
Fixes: e3559442afd2a ("ili210x - rework the touchscreen sample processing")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- add support for system call stack randomization
- handle stale PCI deconfiguration events
- couple of defconfig updates
- some fixes and cleanups
* tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix detection of vector enhancements facility 1 vs. vector packed decimal facility
s390/entry: add support for syscall stack randomization
s390/configs: change CONFIG_VIRTIO_CONSOLE to "m"
s390/cio: remove invalid condition on IO_SCH_UNREG
s390/cpumf: remove call to perf_event_update_userpage
s390/cpumf: move counter set size calculation to common place
s390/cpumf: beautify if-then-else indentation
s390/configs: enable CONFIG_PCI_IOV
s390/pci: handle stale deconfiguration events
s390/pci: rename zpci_configure_device()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux
Pull pcmcia updates from Dominik Brodowski:
"A number of patches fixing W=1 kernel build warnings, and one patch
removing an always-false NULL check"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: rsrc_nonstatic: Fix call-back function as reference formatting
pcmcia: pcmcia_resource: Fix some kernel-doc formatting/disparities and demote others
pcmcia: ds: Fix function name disparity in header
pcmcia: pcmcia_cis: Demote non-conforming kernel-doc headers to standard kernel-doc
pcmcia: cistpl: Demote non-conformant kernel-doc headers to standard comments
pcmcia: rsrc_nonstatic: Demote kernel-doc abuses
pcmcia: ds: Remove if with always false condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert one recent commit that turned out to be problematic,
address two issues in the ACPI "custom method" interface and update
GPIO properties documentation.
Specifics:
- Revent recent commit related to the handling of ACPI power
resources during initialization, because it turned out to cause
problems to occur on some systems (Rafael Wysocki).
- Fix potential use-after-free and potential memory leak in the ACPI
"custom method" debugfs interface (Mark Langsdorf).
- Update ACPI GPIO properties documentation to cover assumptions
regarding GPIO polarity (Andy Shevchenko)"
* tag 'acpi-5.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: scan: Turn off unused power resources during initialization"
ACPI: custom_method: fix a possible memory leak
ACPI: custom_method: fix potential use-after-free issue
Documentation: firmware-guide: gpio-properties: Add note to SPI CS case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Several Renesas binding fixes to fix warnings
- Remove duplicate compatibles in 8250 binding
- Remove orphaned Sigma Designs Tango bindings
- Fix bcm2711-hdmi binding to use 'additionalProperties'
- Fix idt,32434-pic warning for missing 'interrupts' property
- Fix 'stored but not read' warnings in DT overlay code
* tag 'devicetree-fixes-for-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: net: renesas,etheravb: Fix optional second clock name
dt-bindings: display: renesas,du: Add missing power-domains property
dt-bindings: media: renesas,vin: Make resets optional on R-Car Gen1
dt-bindings: PCI: rcar-pci-host: Document missing R-Car H1 support
of: overlay: Remove redundant assignment to ret
dt-bindings: serial: 8250: Remove duplicated compatible strings
dt-bindings: Remove unused Sigma Designs Tango bindings
dt-bindings: bcm2711-hdmi: Fix broken schema
dt-bindings: interrupt-controller: idt,32434-pic: Add missing interrupts property
|
|
* acpi-pm:
Revert "ACPI: scan: Turn off unused power resources during initialization"
* acpi-docs:
Documentation: firmware-guide: gpio-properties: Add note to SPI CS case
|
|
The m_can_start_xmit() function checks if the cdev->tx_skb is NULL and
returns with NETDEV_TX_BUSY in case tx_sbk is not NULL.
There is a race condition in the m_can_tx_work_queue(), where first
the skb is send to the driver and then the case tx_sbk is set to NULL.
A TX complete IRQ might come in between and wake the queue, which
results in tx_skb not being cleared yet.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Tested-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since 8ce8c0abcba3 the driver queues work via priv->restart_work when
resuming after suspend, even when the interface was not previously
enabled. This causes a null dereference error as the workqueue is only
allocated and initialized in mcp251x_open().
To fix this we move the workqueue init to mcp251x_can_probe() as there
is no reason to do it later and repeat it whenever mcp251x_open() is
called.
Fixes: 8ce8c0abcba3 ("can: mcp251x: only reset hardware as required")
Link: https://lore.kernel.org/r/17d5d714-b468-482f-f37a-482e3d6df84e@kontron.de
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[mkl: fix error handling in mcp251x_stop()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
