| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
Thanks for your patch. A more general solution would be to move the
rx_dropped up into sky2_receive.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If receive buffer mapping failed, then it was possible to get
stuck with unmapped receive buffer in DMA ring.
This would be an extremely rare condition because the driver had just
released the map for the last receive so it should be able to get
another map again (in soft-irq).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses concerns about efficiency of handling incoming
packets. Handling of interrupts is done in a threaded interrupt handler
which has a smaller latency than workqueues. This change needed a rework
of the locking scheme that was much simplified. Some other (more or less
longstanding) bugs are fixed: utilization of just half of the RX
buffers, useless wait for interrupt on open, more reliable reset
sequence. The MERR interrupt is not used anymore: it overloads the CPU
in error-passive state without any additional information. One shot mode
is disabled because it's not clear if it can be handled efficiently on
this CAN controller.
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to maintain stats in the bonding structure.
Use the instance of net_device_stats in netdevice.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to use macvlan with qemu and other tools that require
a tap file descriptor, the macvtap driver adds a small backend
with a character device with the same interface as the tun
driver, with a minimum set of features.
Macvtap interfaces are created in the same way as macvlan
interfaces using ip link, but the netif is just used as a
handle for configuration and accounting, while the data
goes through the chardev. Each macvtap interface has its
own character device, simplifying permission management
significantly over the generic tun/tap driver.
Cc: Patrick McHardy <kaber@trash.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Or Gerlitz <ogerlitz@voltaire.com>
Cc: netdev@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes it possible to hook into the macvlan driver
from another kernel module. In particular, the goal is
to extend it with the macvtap backend that provides
a tun/tap compatible interface directly on the macvlan
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error return should be negative. Its only caller that acts upon its
return, handle_bmsg(), transmits the positive error but can also return
negative errors.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove these compiler warnings:
drivers/isdn/hardware/mISDN/w6692.c:534: warning: `setvolume' defined but not used
drivers/isdn/hardware/mISDN/w6692.c:561: warning: `enable_pots' defined but not used
by moving the functions inside #if 0 ... #endif. And an alternative is
to remove them completely if nobody has plans to use them.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If setup_instance() fails we kfree() the card, and then use it in the next
loop iteration. So lets bail out of the loop instead.
Coverity CID: 13357
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With `while (timeout++ < maxdelay)' timeout reaches maxdelay + 1 after the
loop This is probably unlikely a problem in practice.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix crash where resources are freed twice on an eeh recovery failure.
If eeh recovery fails we set a flag to indicate to close() that
resources have been freed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issue asic reset and verify functionality before continuing to the
resume call. This allows proper error code to be returned in the case
the asic does not recover.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allocates the ring structures themselves on each
NUMA node along with the buffer_info structures. This way we
don't allocate the entire ring memory on a single node in one
big block, thus reducing NUMA node memory crosstalk.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default policy for the current driver is to do all its memory
allocation on whatever processor is running insmod/modprobe. This
is less than optimal.
This driver's default mode of operation will be to use each node for each
subsequent transmit/receive queue. The most efficient allocation will be
to then have the interrupts bound in such a way as to match up the
interrupt of the queue to the cpu where its memory was allocated.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a call to pci_save_state() immediately after
the call to pci_restore_state(). Due to a change in the behavior
of pci_restore_state() it is necessary to call pci_save_state()
to keep the state_saved flag. This patch is based on a similar
patch for ixgbe.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this change ethtool will correctly report link status when
the interface is down. Currently ethtool reports the link as not
detected when the interface is down.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Processing multiple ixgbe_watchdog_task calls may cause
the link_up variable and IXGBE_FLAG_NEED_LINK_UPDATE flag
to be set incorrectly. In the worse case this is causing
the netif_carrier_off to be called inappropriately which
results in an interface that can't be brought up.
Although schedule_work() will only schedule the task if
it is not already on the work queue the WORK_STRUCT_PENDING
bits are cleared just before calling the work function.
This allows WORK_STRUCT_PENDING to be cleared, the work
function to start and meanwhile schedule another task.
This patch adds a mutex to the watchdog task. This bug is
actualized by changing DCB settings or doing extended
cable pull or reset tests.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
a developer had complained of getting lots of warnings:
"eth16 selects TX queue 98, but real number of TX queues is 64"
http://www.mail-archive.com/e1000-devel@lists.sourceforge.net/msg02200.html
As there was no follow up on that bug, I am submitting this
patch assuming that the other return points will not return
invalid txq's, and also that this fixes the bug (not tested).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e5a43549f7a58509a91b299a51337d386697b92c (ixgbe: remove
skb_dma_map/unmap calls from driver) looks to have introduced a bug in
ixgbe_tx_map. If we get an error from a PCI DMA call, we loop backwards
through count until it becomes -1 and return that.
The caller of ixgbe_tx_map expects 0 on error, so return that instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o context resources can be in used, while resource cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For NX2031, first try to scrub interrupt before requesting firmware
reset. Return statement was missing after scrubbbing interrupt.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier refactoring has made these inclusions unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In particular, the comment about EVQ_RPTR_REG is based on inconsistent
preliminary hardware documentation, though the following code was
fixed long before release.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SFC9000-family boards do not all use MDIO PHYs, so we need a different
test for PHY aliveness.
Introduce a PHY operation test_alive(). For PHYs attached to Falcon,
use a common implementation based on the existing PHY MDIO test.
For PHYs managed through MCDI, use the appropriate MCDI request.
Change test name in ethtool from 'core mdio' to 'phy alive'.
Rename test_results::mdio to phy_alive and test_results::phy to phy_ext.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows the driver to recover if the MC firmware has crashed due
to an assertion failure.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is for CAN interface cards based on the PLX90xx PCI bridge.
Driver supports now:
- Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/)
- Adlink PCI-7841/cPCI-7841 SE card
- Marathon CAN-bus-PCI card (http://www.marathon.ru/)
- TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)
Changes since v1:
- Added some defines for static inline int plx_pci_check_sja1000(...)
- static struct pci_device_id plx_pci_tbl[] replaced by
static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl)
- Typo fixed
Signed-off-by: Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add memory barriers to fix crashes observed on newest PowerPC platforms.
The HW and driver state of the receive rings were getting out of sync.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The book keeping structure for transmit always had the flags value
cleared so transmit DMA maps were never released correctly.
Based on patch by Jarek Poplawski, problem observed by Michael Breuer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ChangeLog:
Implement .reset_resume support to retain a live network connection
during suspend despite USB power loss.
- rework operation to reference cached data in mcs7830_data and
netdev->dev_addr
- update netdev->dev_addr only in case new MAC was set successfully
. Tests done:
. ethtool -d pre-/post-suspend: register values match
. running ssh session suspend, resume: works
. ifdown device, suspend, resume: works
. ifup, suspend, unplug, resume: WORKS (eth1 is removed, re-ifup of eth1
after card replug works)
. verified identical MAC in ifconfig post-resume
(ok, should be verified on network side to be fully certain...)
Keywords: suspend resume network connection dead interface down
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ChangeLog:
- rename register, add comment
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ChangeLog:
- spelling corrections / whitespace
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ChangeLog:
- evaluate Rx error statistics from trailing Rx status byte
- add driver TODO list
- add myself to authors
Quilt series run-tested, based on 2.6.33-rc4 (net-2.6.git mcs7830 has idle history,
should be good to go).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
