| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch sets STATUS_EXIT_PENDING on pci_remove. Otherwise
iwl4965_down may fail to uninitialize the driver.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch calls apm stop on exit and suspend. Without this patch
hardware consumes power even after driver is removed or suspended.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch "iwlwifi: do not use GFP_DMA in iwl_tx_queue_init" removes
GFP_DMA from allocation tx command buffers. GFP_DMA allows allocation
only for memory under 16M which causes allocation problems
suspend/resume flows.
Using kmalloc is temporal solution and some consistent/coherent
allocation schema will be more correct. Since iwlwifi hardware
supports 64bit address this solution should work on x86 (32 and
64bit) for now.
This patch fixes memory freeing problem in the previous patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes rx_chain computation. The code that adjusts number of
rx chains to number supported by HW was missing. Miss configuration
causes firmware error. Note: iwlwifi supports HW with up to 3 RX
chains (2x2, 2x3, 1x2, and 3x3 MIMO). This patch also simplifies the
whole RX chain computation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes the wrong use MIMO power save values. Our TX was
configured with our MIMO power save values instead of peer's MIMO power
save values, this may affect connectivity. The peer STA/AP may not sense
our traffic at all as it doesn't have all RX chains opened.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rx chain might change during power save transitions but it doesn't
require sending Full-ROXN command to the firmware. Full-RXON requires
reconnection to an AP and thus affects user experience. The patch
avoids the Full-RXON by removing the rx_chain modification check in
iwl_full_rxon_required function.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This enables sending of direct probes on passive channels, as long as
traffic was detected on that channel. This enables connectivity to
hidden/non broadcasting SSIDs APs on passive channels. Note 5000 HW
declares all 5.2 spectrum as passive.
Signed-off-by: Cahill Ben <ben.m.cahill@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is a W/A for the TSF sync issue in IBSS merging. HW is not
capable to sync TSF (it's constantly little behind). This creates
constant IBSS merging upon reception of each beacon, adding and removing
station which in turn creates above 50% packet loss and thus dramatically
degrade the throughput. The W/A simply stops the driver from declaring it
has a reliable TSF value and thus eliminates IBSS merging.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove chipset-specific quirk workaround; the workaround caused
unrecoverable DMA lockups when the driver was loaded following a
PXE boot.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
pcnet_cs:
add new ID: "corega Ether PCC-TD".
remove duplicate ID: "IC-CARD".
axnet_cs:
add new ID: "IO DATA ETXPCM".
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40ae0e6508d6c717b6e0d6d81cd77ac25
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Make the "pegasus" driver scream less loudly in the face of
problems as it initializes, avoiding hundreds of messages:
- ratelimit some key error messages
- avoid some spurious diagnostics caused by strange codeflow
And fix one instance of goofy indentation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch addresses an issue with the locking order. ath_rx_flush_tid()
uses spin_lock/unlock_bh when IRQs are disabled in sta_notify by mac80211.
As node clean up is still pending with ath9k and this problematic portion
of the code is expected to change anyway, thinking of a proper fix may not
be worthwhile. So having this interim fix helps the users to get rid of the
kernel warning message.
Pasted the kernel warning message for reference.
kernel: ath0: No ProbeResp from current AP 00:1b:11:60:7a:3d - assume out of range
kernel: ------------[ cut here ]------------
kernel: WARNING: at kernel/softirq.c:136 local_bh_enable+0x3c/0xab()
kernel: Pid: 1029, comm: ath9k Not tainted 2.6.27-rc4-wt-w1fi-wl
kernel:
kernel: Call Trace:
kernel: [<ffffffff802278d8>] warn_on_slowpath+0x51/0x77
kernel: [<ffffffff80224c51>] check_preempt_wakeup+0xf3/0x123
kernel: [<ffffffff80239658>] autoremove_wake_function+0x9/0x2e
kernel: [<ffffffff8022c281>] local_bh_enable+0x3c/0xab
kernel: [<ffffffffa01ab75a>] ath_rx_node_cleanup+0x38/0x6e [ath9k]
kernel: [<ffffffffa01b2280>] ath_node_detach+0x3b/0xb6 [ath9k]
kernel: [<ffffffffa01ab09f>] ath9k_sta_notify+0x12b/0x165 [ath9k]
kernel: [<ffffffff802366cf>] queue_work+0x1d/0x49
kernel: [<ffffffffa018c3fc>] add_todo+0x70/0x99 [mac80211]
kernel: [<ffffffffa017de76>] __sta_info_unlink+0x16b/0x19e [mac80211]
kernel: [<ffffffffa017e6ed>] sta_info_unlink+0x18/0x43 [mac80211]
kernel: [<ffffffffa0182732>] ieee80211_associated+0xaa/0x16d [mac80211]
kernel: [<ffffffffa0184a1a>] ieee80211_sta_work+0x4fb/0x6b4 [mac80211]
kernel: [<ffffffff80469c58>] thread_return+0x30/0xa9
kernel: [<ffffffffa018451f>] ieee80211_sta_work+0x0/0x6b4 [mac80211]
kernel: [<ffffffff802362c2>] run_workqueue+0xb1/0x17a
kernel: [<ffffffff80236be9>] worker_thread+0xd0/0xdb
kernel: [<ffffffff8023964f>] autoremove_wake_function+0x0/0x2e
kernel: [<ffffffff80236b19>] worker_thread+0x0/0xdb
kernel: [<ffffffff8023954a>] kthread+0x47/0x75
kernel: [<ffffffff80223121>] schedule_tail+0x18/0x50
kernel: [<ffffffff8020bc49>] child_rip+0xa/0x11
kernel: [<ffffffff80239503>] kthread+0x0/0x75
kernel: [<ffffffff8020bc3f>] child_rip+0x0/0x11
kernel:
kernel: ---[ end trace e9bb5da661055827 ]---
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Updating sc_keytype multiple times when groupwise and pairwise
ciphers are different results in incorrect pairwise key type
assumed for TX control and normal ping fails. This works fine
for cases where both groupwise and pairwise ciphers are same.
Also use mac80211 provided enums for key length calculation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The leak in if_cs_prog_helper() is obvious.
It looks a bit as if not freeing "fw" in if_cs_prog_real() was done
intentionally, but I'm not seeing why it shouldn't be freed.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When multicasting the driver sets the number of group addresses using
the count from the previous set multicast command. In general this means
you have to set the multicast addresses twice to get the behaviour you
want.
If we were multicasting, and reduce the number of addresses we are
multicasting to, then the driver would write uninitialised data from the
stack into the group addresses to multicast to.
Only write the multicast addresses we have specifically set.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes loading firmware from memory above 32bit.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Marcel Holtmann <holtmann@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch fixes CSR_GP_CNTRL_REG_FLAG_INIT_DONE was set instead of
cleared which disabled moving device to D0U state.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds workaround for an interrupt related hardware bug on
some platforms. (Apparently these platforms boot-up w/ INTX_DISABLED
set. -- JWL)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
GFP_DMA is not necessary for the iwlwifi hardware and it can cause
allocation failures and/or invoke the OOM killer on lots of systems.
For reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459709
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are missing capability checks in the following code:
1300 static int
1301 sbni_ioctl( struct net_device *dev, struct ifreq *ifr, int cmd)
1302 {
[...]
1319 case SIOCDEVRESINSTATS :
1320 if( current->euid != 0 ) /* root only */
1321 return -EPERM;
[...]
1336 case SIOCDEVSHWSTATE :
1337 if( current->euid != 0 ) /* root only */
1338 return -EPERM;
[...]
1357 case SIOCDEVENSLAVE :
1358 if( current->euid != 0 ) /* root only */
1359 return -EPERM;
[...]
1372 case SIOCDEVEMANSIPATE :
1373 if( current->euid != 0 ) /* root only */
1374 return -EPERM;
Here's my proposed fix:
Missing capability checks.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
There were 2 omitted readb's used on an iomap space. eliminate them
by using ioread8 instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When a preallocated header qdio buffer is filled we have to account
the offset for the data length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
In case the netdev unicast list contains additional entries we have
to register/deregister them.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
return value -ENOTSUPP is not valid in userspace context, use
-EOPNOTSUPP instead.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We must not call dev_mc_add() from within our HW configure which happens
before we initialize and register the netdev. Do it in open() instead.
Thanks to Sebastian Siewior for tracking it down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
I got the following backtrace while network was unavailble:
|NETDEV WATCHDOG: eth0: transmit timed out
|BUG: sleeping function called from invalid context at /home/bigeasy/git/linux-2.6-powerpc/kernel/mutex.c:87
|in_atomic():1, irqs_disabled():0
|Call Trace:
|[c0383d90] [c0006dd8] show_stack+0x48/0x184 (unreliable)
|[c0383db0] [c001e938] __might_sleep+0xe0/0xf4
|[c0383dc0] [c025a43c] mutex_lock+0x24/0x3c
|[c0383de0] [c019005c] phy_stop+0x20/0x70
|[c0383df0] [c018d4ec] stop_gfar+0x28/0xf4
|[c0383e10] [c018e8c4] gfar_timeout+0x30/0x60
|[c0383e20] [c01fe7c0] dev_watchdog+0xa8/0x144
|[c0383e30] [c002f93c] run_timer_softirq+0x148/0x1c8
|[c0383e60] [c002b084] __do_softirq+0x5c/0xc4
|[c0383e80] [c00046fc] do_softirq+0x3c/0x54
|[c0383e90] [c002ac60] irq_exit+0x3c/0x5c
|[c0383ea0] [c000b378] timer_interrupt+0xe0/0xf8
|[c0383ec0] [c000e5ac] ret_from_except+0x0/0x18
|[c0383f80] [c000804c] cpu_idle+0xcc/0xdc
|[c0383fa0] [c025c07c] etext+0x7c/0x90
|[c0383fc0] [c0338960] start_kernel+0x294/0x2a8
|[c0383ff0] [c00003dc] skpinv+0x304/0x340
|------------[ cut here ]------------
The phylock was once a spinlock but got changed into a mutex via
commit 35b5f6b1a aka [PHYLIB: Locking fixes for PHY I/O potentially sleeping]
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Manfred Spraul <manfred@colorfullife.com
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Viktor Horvath <ViktorHorvath@gmx.net>
Cc: Robbert Wethmar <robbert@wethmar.nl>
Cc: Bart van der Klip <bklip@xs4all.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Properly handle resource cleanup on unplug/exit.
Spotted by Jonathan Cameron
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes dev_kfree_skb happening too many times when hso_start_net_device
is called from hso_resume.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes Icon-322 detection.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The atl1 driver is causing stalled connections and file corruption
whenever TSO is enabled. Two examples are here:
http://lkml.org/lkml/2008/7/15/325
http://lkml.org/lkml/2008/8/18/543
Disable TSO by default until we can determine the source of the
problem.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Doesn't cause problems (yet) because err gets zeroed earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
LCS recovery dumps in irq routine when CCW address in
Subchannel Status Word (SCSW) is zero. This occurs
when recovery is driven after cable reconnect.
Signed-off-by: Klaus-D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use netdev->ml_priv instead of netdev->priv
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
probe_error() frees memory only, if cgdev->dev.driver_data refers
to the claw_privbk structure. Move forward its setting in claw_probe()
to ensure proper freeing of claw_privbk allocations.
Cc: Daniel <danielm77@spray.se>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Alan 'pass the paper bags' Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
