| Age | Commit message (Collapse) | Author |
|---|
|
Update lpfc version to 12.8.0.2
Link: https://lore.kernel.org/r/20200630215001.70793-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Although the existing implementation is very good at high I/O load, on
tests involving light load, especially on only a few hardware queues,
latency was a little higher than it can be due to using workqueue
scheduling. Other tasks in the system can delay handling.
Change the lower level to use irq_poll by default which uses a softirq for
I/O completion. This gives better latency as variance in when the cq is
processed is reduced over the workqueue interface. However, as high load is
better served by not being in softirq when the CPU is loaded, work queues
are still used under high I/O load.
Link: https://lore.kernel.org/r/20200630215001.70793-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, if there has been an issue whereby an adapter dump was taken,
there is nothing displayed to hint that it is present. Utilities must be
run and they must query for the status in order to then download the dump.
Add a message to the driver to query dump image presence when initializing
the SLI Port.
Link: https://lore.kernel.org/r/20200630215001.70793-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently the driver validates command codes received from the
application. COMMON_SET_FEATURES is not currently being approved.
Add definition of the missing command and allow it to be issued by
applications.
Link: https://lore.kernel.org/r/20200630215001.70793-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change vocabulary of 0373 log msg from "error" to "cmpl" The current
language of the 0373 message contains the word "error" which caused a
number of customers to inquire about the "error" and if it should be a
concern. It isn't an error, it's simply an io completion status.
Revise the message to replace the word "error" with "cmpl" for completion.
Link: https://lore.kernel.org/r/20200630215001.70793-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the kdump kernel shuts down lpfc calls flush_work_queue on an
interrupt to schedule the cq handler. When there is only one CPU active on
the kdump kernel, it is possible for the work_on to get scheduled on a
non-active CPU causing it to never be scheduled.
When in the kdump environment, per-CPU affinity of cq's to cpus is not
necessary. In those cases, use a general queue_work rather than a
queue_work_on().
Link: https://lore.kernel.org/r/20200630215001.70793-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Call traces have been observed running different tests that involve aborts
and setting the rrq active flag. The lpfc_set_rrq_active routine is doing
a mempool_alloc under the soft_irq processing level. When the mempool needs
to get a new buffer from the free pool and has to wait for memory to become
free it will check the flags passed in on the alloc and dump the stack if
the thread is running in interrupt context.
Replace the GFP_KERNEL flag with GFP_ATOMIC so that the memory allocation
will not attempt to sleep if there is no mem available.
Link: https://lore.kernel.org/r/20200630215001.70793-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When using DUMP on SLI3 to read VPD and Port status data (config region
23), the adapter is overruning the kmalloc'd buffer causing havoc on other
consumers of the allocation pools.
Rework the loops processing the dump data and validate/size memory lengths
before performing bcopy.
Link: https://lore.kernel.org/r/20200630215001.70793-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Visual code inspection of the MDS implementation revealed two errors in
the driver:
- The set features Feature Code had an incorrect value
- The routine that classifies command type for cmd completions was missing
the Send Frame definition. Send Frame is used for MDS driver loopback.
Link: https://lore.kernel.org/r/20200630215001.70793-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Coverity reported the following error:
Assigned value that is never used may represent unnecessary computation.
The rc variable was initially assigned a value but in several cases, when
an error case is detected, it is reassigned a new value. The initial value
had little use.
In code-reviewing this routine, it could use some cleanup:
- Setting the initialization value to -ENODEV is a much better choice and
lessens code in the routine.
- The wasn't tracking logic errors vs no error and mailbox failure.
Better to resolve by adding a status to track the mailbox failure
and merge it with the logic error when the routine returns.
Link: https://lore.kernel.org/r/20200630215001.70793-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
* Firmware Initialization with SCM enabled based on NVRAM setting and
firmware support (About Firmware).
* Enable PUREX and add support for fabric performance impact
notification (FPIN) handling.
* Allocate a default PUREX item for each vha to handle memory allocation
failures in ISR.
Link: https://lore.kernel.org/r/20200630102229.29660-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SAN Congestion Management generates ELS pkts whose size can vary and be >
64 bytes. Change the PUREX handling code to support non-standard ELS pkt
size.
Link: https://lore.kernel.org/r/20200630102229.29660-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of repeating the code for generating a debug message prefix six
times, introduce a function for computing the debug message prefix.
Link: https://lore.kernel.org/r/20200629225454.22863-10-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of using complicated control flow to only have one return statement
at the end of qla2x00_restart_isp(), return an error status as soon as it
is known that this function will fail.
Link: https://lore.kernel.org/r/20200629225454.22863-9-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
'cnt' can exceed the size of the risc_ram[] array. Prevent that Coverity
complains by rewriting an address calculation expression. This patch fixes
the following Coverity complaint:
CID 337803 (#1 of 1): Out-of-bounds read (OVERRUN)
109. overrun-local: Overrunning array of 122880 bytes at byte offset 122880
by dereferencing pointer &fw->risc_ram[cnt].
Link: https://lore.kernel.org/r/20200629225454.22863-8-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
request_t.handle
The request_t 'handle' member is 32-bits wide, hence use wrt_reg_dword().
Change the cast in the wrt_reg_byte() call to make it clear that a regular
pointer is casted to an __iomem pointer.
Note: 'pkt' points to I/O memory for the qlafx00 adapter family and to
coherent memory for all other adapter families.
This patch fixes the following Coverity complaint:
CID 358864 (#1 of 1): Reliance on integer endianness (INCOMPATIBLE_CAST)
incompatible_cast: Pointer &pkt->handle points to an object whose effective
type is unsigned int (32 bits, unsigned) but is dereferenced as a narrower
unsigned short (16 bits, unsigned). This may lead to unexpected results
depending on machine endianness.
Link: https://lore.kernel.org/r/20200629225454.22863-7-bvanassche@acm.org
Fixes: 8ae6d9c7eb10 ("[SCSI] qla2xxx: Enhancements to support ISPFx00.")
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove an unnecessary cast because it prevents the compiler to perform type
checking.
Link: https://lore.kernel.org/r/20200629225454.22863-6-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following code:
qla82xx_rom_fast_read(ha, 0, &n)
only initializes 'n' if it succeeds. Since 'n' may be reported in a debug
message even if no ROM reads succeeded, initialize 'n' to zero.
This patch fixes the following sparse warning:
qla_nx.c:1218: qla82xx_pinit_from_rom() error: uninitialized symbol 'n'.
Link: https://lore.kernel.org/r/20200629225454.22863-5-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return early instead of having a single return statement at the end of this
function. This patch fixes the following sparse warning:
qla_nx.c:1018: qla82xx_flash_wait_write_finish() error: uninitialized symbol 'val'.
Link: https://lore.kernel.org/r/20200629225454.22863-4-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove the __packed annotation from struct fcp_hdr* because that annotation
is not necessary for these data structures.
Link: https://lore.kernel.org/r/20200629225454.22863-3-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since struct fcp_hdr is used to exchange data with the firmware, check its
size at compile time.
Link: https://lore.kernel.org/r/20200629225454.22863-2-bvanassche@acm.org
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The "head" pointer can't be NULL because it points to an address in the
middle of a ufs_hba struct. Looking at this code, probably someone would
wonder if the intent was to check whether "hba" is NULL, but "hba" isn't
NULL and the check can just be removed.
Link: https://lore.kernel.org/r/20200626105133.GF314359@mwanda
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix typo: "trigerred" --> "triggered"
Link: https://lore.kernel.org/r/20200624135600.14274-1-f.suligoi@asem.it
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If a UFS device is not qualified to use WriteBooster, either due to wrong
UFS version or device-specific quirks, then the capability in host shall be
disabled to prevent any WriteBooster operations in the future.
Link: https://lore.kernel.org/r/20200625030430.25048-1-stanley.chu@mediatek.com
Fixes: 3d17b9b5ab11 ("scsi: ufs: Add write booster feature support")
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Removed all the unused variables.
Link: https://lore.kernel.org/r/20200622093814.3250-1-jhasan@marvell.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The dev_id used in request_irq() and free_irq() should match. Use 'info'
in both cases.
Link: https://lore.kernel.org/r/20200625204730.943520-1-christophe.jaillet@wanadoo.fr
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While building for x86_64 allmodconfig, the following warning was reported:
WARNING: modpost: missing MODULE_LICENSE() in drivers/scsi/ufs/ufs-exynos.o
Add the missing license/author/description tags.
Link: https://lore.kernel.org/r/20200625154405.60448-1-alim.akhtar@samsung.com
Fixes: 55f4b1f73631 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Link: https://lore.kernel.org/r/20200618133837.127274-1-weiyongjun1@huawei.com
Fixes: 55f4b1f73631 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow Exynos UFS driver to build as a module. This patch fixes the
followin build issue reported by kernel build robot.
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_probe':
drivers/scsi/ufs/ufs-exynos.c:1231: undefined reference to `ufshcd_pltfrm_init'
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_pre_pwr_mode':
drivers/scsi/ufs/ufs-exynos.c:635: undefined reference to `ufshcd_get_pwr_dev_param'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_shutdown'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_idle'
Link: https://lore.kernel.org/r/20200620173232.52521-1-alim.akhtar@samsung.com
Fixes: 55f4b1f73631 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes the following crash (see
https://bugzilla.kernel.org/show_bug.cgi?id=208045)
Process iscsi_trx (pid: 7496, stack limit = 0x0000000010dd111a)
CPU: 0 PID: 7496 Comm: iscsi_trx Not tainted 4.19.118-0419118-generic
#202004230533
Hardware name: Greatwall QingTian DF720/F601, BIOS 601FBE20 Sep 26 2019
pstate: 80400005 (Nzcv daif +PAN -UAO)
pc : flush_dcache_page+0x18/0x40
lr : is_ring_space_avail+0x68/0x2f8 [target_core_user]
sp : ffff000015123a80
x29: ffff000015123a80 x28: 0000000000000000
x27: 0000000000001000 x26: ffff000023ea5000
x25: ffffcfa25bbe08b8 x24: 0000000000000078
x23: ffff7e0000000000 x22: ffff000023ea5001
x21: ffffcfa24b79c000 x20: 0000000000000fff
x19: ffff7e00008fa940 x18: 0000000000000000
x17: 0000000000000000 x16: ffff2d047e709138
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: ffff2d047fbd0a40
x11: 0000000000000000 x10: 0000000000000030
x9 : 0000000000000000 x8 : ffffc9a254820a00
x7 : 00000000000013b0 x6 : 000000000000003f
x5 : 0000000000000040 x4 : ffffcfa25bbe08e8
x3 : 0000000000001000 x2 : 0000000000000078
x1 : ffffcfa25bbe08b8 x0 : ffff2d040bc88a18
Call trace:
flush_dcache_page+0x18/0x40
is_ring_space_avail+0x68/0x2f8 [target_core_user]
queue_cmd_ring+0x1f8/0x680 [target_core_user]
tcmu_queue_cmd+0xe4/0x158 [target_core_user]
__target_execute_cmd+0x30/0xf0 [target_core_mod]
target_execute_cmd+0x294/0x390 [target_core_mod]
transport_generic_new_cmd+0x1e8/0x358 [target_core_mod]
transport_handle_cdb_direct+0x50/0xb0 [target_core_mod]
iscsit_execute_cmd+0x2b4/0x350 [iscsi_target_mod]
iscsit_sequence_cmd+0xd8/0x1d8 [iscsi_target_mod]
iscsit_process_scsi_cmd+0xac/0xf8 [iscsi_target_mod]
iscsit_get_rx_pdu+0x404/0xd00 [iscsi_target_mod]
iscsi_target_rx_thread+0xb8/0x130 [iscsi_target_mod]
kthread+0x130/0x138
ret_from_fork+0x10/0x18
Code: f9000bf3 aa0003f3 aa1e03e0 d503201f (f9400260)
---[ end trace 1e451c73f4266776 ]---
The solution is based on patch:
"scsi: target: tcmu: Optimize use of flush_dcache_page"
which restricts the use of tcmu_flush_dcache_range() to addresses from
vmalloc'ed areas only.
This patch now replaces the virt_to_page() call in
tcmu_flush_dcache_range() - which is wrong for vmalloced addrs - by
vmalloc_to_page().
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-3-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Tested-by: Daniel Meyerholt <dxm523@gmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Tested-by: Daniel Meyerholt <dxm523@gmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Delete trailing whitespace, multiple blank lines, and make switch/case be
at the same indentation.
Link: https://lore.kernel.org/r/20200619154117.10262-3-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After commit f664a3cc17b7 ("scsi: kill off the legacy IO path"),
scsi_sdb_cache is not used anymore. Remove it.
Link: https://lore.kernel.org/r/20200619154117.10262-2-huobean@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since commit 61fb24822166 ("scsi: target: tcmu: Userspace must not complete
queued commands") tcmu_cmd bit TCMU_CMD_BIT_INFLIGHT is set but never
checked. So we can remove it safely.
[mkp: fixed Mike's email address]
Link: https://lore.kernel.org/r/20200619173806.5016-1-bstroesser@ts.fujitsu.com
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a spelling mistake in a dev_warn message. Fix it.
Link: https://lore.kernel.org/r/20200617084911.167359-1-colin.king@canonical.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix build warning reported by kernel test robot:
Warning:
>> drivers/scsi/ufs/ufs-mediatek.c:181:5: warning: no previous prototype
>> for 'ufs_mtk_wait_link_state' [-Wmissing-prototypes]
Link: https://lore.kernel.org/r/20200616095120.14570-1-stanley.chu@mediatek.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The UFS load calculation is based on "total_time" and "busy_time" in a
devfreq window. However, the source of time is different for both
parameters: "busy_time" is assigned from "jiffies" thus has different
accuracy from "total_time" which is assigned from ktime_get().
In addition, the time of window boundary is not exactly the same as the
starting busy time in this window if UFS is actually busy in the beginning
of the window. A similar accuracy error may also happen for the end of busy
time in current window.
To guarantee the precision of load calculation, we need to
1. Align time accuracy of both devfreq_dev_status.total_time and
devfreq_dev_status.busy_time. For example, use "ktime_get()" directly.
2. Align the following timelines:
- The beginning time of devfreq windows
- The beginning of busy time in a new window
- The end of busy time in the current window
Link: https://lore.kernel.org/r/20200611101043.6379-1-stanley.chu@mediatek.com
Fixes: a3cd5ec55f6c ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the ftrace infrastructure to conditionally trace UFS UIC command
events.
New trace event "ufshcd_uic_command" is created, which samples the
following UFS UIC command data:
- Device name
- Optional identification string
- UIC command opcode
- UIC command argument1
- UIC command argument2
- UIC command argement3
Usage:
echo 1 > /sys/kernel/debug/tracing/events/ufs/enable
cat /sys/kernel/debug/tracing/trace_pipe
Link: https://lore.kernel.org/r/20200615072235.23042-3-stanley.chu@mediatek.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove unused fields "cmd_active" and "result" in struct ufs_command.
Link: https://lore.kernel.org/r/20200615072235.23042-2-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Clean up the following items:
- Sort vendor names in alphabetical order
- Squash quirks as compact as possible in device table to enhance
performance of the lookup
- Sort device quirks in alphabetical order
Link: https://lore.kernel.org/r/20200612012625.6615-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is confirmed that Micron device needs DELAY_BEFORE_LPM quirk to have a
delay before VCC is powered off. Sdd Micron vendor ID and this quirk for
Micron devices.
Link: https://lore.kernel.org/r/20200612012625.6615-2-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix typo: "tigger" --> "trigger"
Link: https://lore.kernel.org/r/20200609161313.32098-1-f.suligoi@asem.it
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The word 'descriptor' is misspelled throughout the tree.
Fix it up accordingly:
decriptors -> descriptors
Link: https://lore.kernel.org/r/20200609124610.3445662-7-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add SPDX GPL-2.0 to UFS driver files that specified the GPL version 2
license, remove the full boilerplate text.
Link: https://lore.kernel.org/r/20200605200520.20831-2-huobean@gmail.com
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For UFS 3.1, the normal unit descriptor is 10 bytes larger than the RPMB
unit. However, both descriptors share the same desc_idn, to cover both unit
descriptors with one length, we choose the normal unit descriptor length by
desc_index.
Link: https://lore.kernel.org/r/20200603091959.27618-6-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
At UFS initialization stage, to get the length of the descriptor,
ufshcd_read_desc_length() was being called 6 times. Instead, we will
capture the descriptor size the first time we'll read it.
Delete unnecessary redundant code, remove ufshcd_read_desc_length(),
ufshcd_init_desc_sizes(), and boost UFS initialization.
Link: https://lore.kernel.org/r/20200603091959.27618-5-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
